From 5b0c02f9b8acf2a791e531bbc09acae2d51f4f9b Mon Sep 17 00:00:00 2001 From: Nicolas Frattaroli Date: Sat, 22 Feb 2025 20:39:57 +0100 Subject: [PATCH 1/7] ASoC: es8328: fix route from DAC to output The ES8328 codec driver, which is also used for the ES8388 chip that appears to have an identical register map, claims that the output can either take the route from DAC->Mixer->Output or through DAC->Output directly. To the best of what I could find, this is not true, and creates problems. Without DACCONTROL17 bit index 7 set for the left channel, as well as DACCONTROL20 bit index 7 set for the right channel, I cannot get any analog audio out on Left Out 2 and Right Out 2 respectively, despite the DAPM routes claiming that this should be possible. Furthermore, the same is the case for Left Out 1 and Right Out 1, showing that those two don't have a direct route from DAC to output bypassing the mixer either. Those control bits toggle whether the DACs are fed (stale bread?) into their respective mixers. If one "unmutes" the mixer controls in alsamixer, then sure, the audio output works, but if it doesn't work without the mixer being fed the DAC input then evidently it's not a direct output from the DAC. ES8328/ES8388 are seemingly not alone in this. ES8323, which uses a separate driver for what appears to be a very similar register map, simply flips those two bits on in its probe function, and then pretends there is no power management whatsoever for the individual controls. Fair enough. My theory as to why nobody has noticed this up to this point is that everyone just assumes it's their fault when they had to unmute an additional control in ALSA. Fix this in the es8328 driver by removing the erroneous direct route, then get rid of the playback switch controls and have those bits tied to the mixer's widget instead, which until now had no register to play with. Fixes: 567e4f98922c ("ASoC: add es8328 codec driver") Signed-off-by: Nicolas Frattaroli Link: https://patch.msgid.link/20250222-es8328-route-bludgeoning-v1-1-99bfb7fb22d9@collabora.com Signed-off-by: Mark Brown --- sound/soc/codecs/es8328.c | 15 ++++----------- 1 file changed, 4 insertions(+), 11 deletions(-) diff --git a/sound/soc/codecs/es8328.c b/sound/soc/codecs/es8328.c index f3c97da798dc..76159c45e6b5 100644 --- a/sound/soc/codecs/es8328.c +++ b/sound/soc/codecs/es8328.c @@ -233,7 +233,6 @@ static const struct snd_kcontrol_new es8328_right_line_controls = /* Left Mixer */ static const struct snd_kcontrol_new es8328_left_mixer_controls[] = { - SOC_DAPM_SINGLE("Playback Switch", ES8328_DACCONTROL17, 7, 1, 0), SOC_DAPM_SINGLE("Left Bypass Switch", ES8328_DACCONTROL17, 6, 1, 0), SOC_DAPM_SINGLE("Right Playback Switch", ES8328_DACCONTROL18, 7, 1, 0), SOC_DAPM_SINGLE("Right Bypass Switch", ES8328_DACCONTROL18, 6, 1, 0), @@ -243,7 +242,6 @@ static const struct snd_kcontrol_new es8328_left_mixer_controls[] = { static const struct snd_kcontrol_new es8328_right_mixer_controls[] = { SOC_DAPM_SINGLE("Left Playback Switch", ES8328_DACCONTROL19, 7, 1, 0), SOC_DAPM_SINGLE("Left Bypass Switch", ES8328_DACCONTROL19, 6, 1, 0), - SOC_DAPM_SINGLE("Playback Switch", ES8328_DACCONTROL20, 7, 1, 0), SOC_DAPM_SINGLE("Right Bypass Switch", ES8328_DACCONTROL20, 6, 1, 0), }; @@ -336,10 +334,10 @@ static const struct snd_soc_dapm_widget es8328_dapm_widgets[] = { SND_SOC_DAPM_DAC("Left DAC", "Left Playback", ES8328_DACPOWER, ES8328_DACPOWER_LDAC_OFF, 1), - SND_SOC_DAPM_MIXER("Left Mixer", SND_SOC_NOPM, 0, 0, + SND_SOC_DAPM_MIXER("Left Mixer", ES8328_DACCONTROL17, 7, 0, &es8328_left_mixer_controls[0], ARRAY_SIZE(es8328_left_mixer_controls)), - SND_SOC_DAPM_MIXER("Right Mixer", SND_SOC_NOPM, 0, 0, + SND_SOC_DAPM_MIXER("Right Mixer", ES8328_DACCONTROL20, 7, 0, &es8328_right_mixer_controls[0], ARRAY_SIZE(es8328_right_mixer_controls)), @@ -418,19 +416,14 @@ static const struct snd_soc_dapm_route es8328_dapm_routes[] = { { "Right Line Mux", "PGA", "Right PGA Mux" }, { "Right Line Mux", "Differential", "Differential Mux" }, - { "Left Out 1", NULL, "Left DAC" }, - { "Right Out 1", NULL, "Right DAC" }, - { "Left Out 2", NULL, "Left DAC" }, - { "Right Out 2", NULL, "Right DAC" }, - - { "Left Mixer", "Playback Switch", "Left DAC" }, + { "Left Mixer", NULL, "Left DAC" }, { "Left Mixer", "Left Bypass Switch", "Left Line Mux" }, { "Left Mixer", "Right Playback Switch", "Right DAC" }, { "Left Mixer", "Right Bypass Switch", "Right Line Mux" }, { "Right Mixer", "Left Playback Switch", "Left DAC" }, { "Right Mixer", "Left Bypass Switch", "Left Line Mux" }, - { "Right Mixer", "Playback Switch", "Right DAC" }, + { "Right Mixer", NULL, "Right DAC" }, { "Right Mixer", "Right Bypass Switch", "Right Line Mux" }, { "DAC DIG", NULL, "DAC STM" }, From 0da83ab025bc45e9742e87c2cce19bff423377c8 Mon Sep 17 00:00:00 2001 From: Chancel Liu Date: Mon, 17 Feb 2025 10:04:37 +0900 Subject: [PATCH 2/7] ASoC: fsl: Rename stream name of SAI DAI driver If stream names of DAI driver are duplicated there'll be warnings when machine driver tries to add widgets on a route: [ 8.831335] fsl-asoc-card sound-wm8960: ASoC: sink widget CPU-Playback overwritten [ 8.839917] fsl-asoc-card sound-wm8960: ASoC: source widget CPU-Capture overwritten Use different stream names to avoid such warnings. DAI names in AUDMIX are also updated accordingly. Fixes: 15c958390460 ("ASoC: fsl_sai: Add separate DAI for transmitter and receiver") Signed-off-by: Chancel Liu Acked-by: Shengjiu Wang Link: https://patch.msgid.link/20250217010437.258621-1-chancel.liu@nxp.com Signed-off-by: Mark Brown --- sound/soc/fsl/fsl_sai.c | 6 +++--- sound/soc/fsl/imx-audmix.c | 4 ++-- 2 files changed, 5 insertions(+), 5 deletions(-) diff --git a/sound/soc/fsl/fsl_sai.c b/sound/soc/fsl/fsl_sai.c index c4eb87c5d39e..9f33dd11d47f 100644 --- a/sound/soc/fsl/fsl_sai.c +++ b/sound/soc/fsl/fsl_sai.c @@ -994,10 +994,10 @@ static struct snd_soc_dai_driver fsl_sai_dai_template[] = { { .name = "sai-tx", .playback = { - .stream_name = "CPU-Playback", + .stream_name = "SAI-Playback", .channels_min = 1, .channels_max = 32, - .rate_min = 8000, + .rate_min = 8000, .rate_max = 2822400, .rates = SNDRV_PCM_RATE_KNOT, .formats = FSL_SAI_FORMATS, @@ -1007,7 +1007,7 @@ static struct snd_soc_dai_driver fsl_sai_dai_template[] = { { .name = "sai-rx", .capture = { - .stream_name = "CPU-Capture", + .stream_name = "SAI-Capture", .channels_min = 1, .channels_max = 32, .rate_min = 8000, diff --git a/sound/soc/fsl/imx-audmix.c b/sound/soc/fsl/imx-audmix.c index 50ecc5f51100..dac5d4ddacd6 100644 --- a/sound/soc/fsl/imx-audmix.c +++ b/sound/soc/fsl/imx-audmix.c @@ -119,8 +119,8 @@ static const struct snd_soc_ops imx_audmix_be_ops = { static const char *name[][3] = { {"HiFi-AUDMIX-FE-0", "HiFi-AUDMIX-FE-1", "HiFi-AUDMIX-FE-2"}, {"sai-tx", "sai-tx", "sai-rx"}, - {"AUDMIX-Playback-0", "AUDMIX-Playback-1", "CPU-Capture"}, - {"CPU-Playback", "CPU-Playback", "AUDMIX-Capture-0"}, + {"AUDMIX-Playback-0", "AUDMIX-Playback-1", "SAI-Capture"}, + {"SAI-Playback", "SAI-Playback", "AUDMIX-Capture-0"}, }; static int imx_audmix_probe(struct platform_device *pdev) From d31babd7e304d3b800d36ff74be6739405b985f2 Mon Sep 17 00:00:00 2001 From: Nicolas Frattaroli Date: Fri, 21 Feb 2025 21:39:32 +0100 Subject: [PATCH 3/7] ASoC: dapm-graph: set fill colour of turned on nodes Some tools like KGraphViewer interpret the "ON" nodes not having an explicitly set fill colour as them being entirely black, which obscures the text on them and looks funny. In fact, I thought they were off for the longest time. Comparing to the output of the `dot` tool, I assume they are supposed to be white. Instead of speclawyering over who's in the wrong and must immediately atone for their wickedness at the altar of RFC2119, just be explicit about it, set the fillcolor to white, and nobody gets confused. Signed-off-by: Nicolas Frattaroli Tested-by: Luca Ceresoli Reviewed-by: Luca Ceresoli Link: https://patch.msgid.link/20250221-dapm-graph-node-colour-v1-1-514ed0aa7069@collabora.com Signed-off-by: Mark Brown --- tools/sound/dapm-graph | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/sound/dapm-graph b/tools/sound/dapm-graph index f14bdfedee8f..b6196ee5065a 100755 --- a/tools/sound/dapm-graph +++ b/tools/sound/dapm-graph @@ -10,7 +10,7 @@ set -eu STYLE_COMPONENT_ON="color=dodgerblue;style=bold" STYLE_COMPONENT_OFF="color=gray40;style=filled;fillcolor=gray90" -STYLE_NODE_ON="shape=box,style=bold,color=green4" +STYLE_NODE_ON="shape=box,style=bold,color=green4,fillcolor=white" STYLE_NODE_OFF="shape=box,style=filled,color=gray30,fillcolor=gray95" # Print usage and exit From 56a677293509b2a0d39ac8d02b583c1ab1fe4d94 Mon Sep 17 00:00:00 2001 From: Bard Liao Date: Tue, 25 Feb 2025 17:37:15 +0800 Subject: [PATCH 4/7] ASoC: SOF: Intel: don't check number of sdw links when set dmic_fixup MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Currently, we assume that the PCH DMIC pins are pin-muxed with SoundWire links. However, we do see a HW design that use PCH DMIC along with 3 SoundWire links. Remove the check now. With this change the PCM DMIC will be presented if it is reported by the BIOS irrespective of whether there are SDW links present or not. Signed-off-by: Bard Liao Reviewed-by: Ranjani Sridharan Reviewed-by: Péter Ujfalusi Link: https://patch.msgid.link/20250225093716.67240-2-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown --- sound/soc/sof/intel/hda.c | 18 ++---------------- 1 file changed, 2 insertions(+), 16 deletions(-) diff --git a/sound/soc/sof/intel/hda.c b/sound/soc/sof/intel/hda.c index be689f6e10c8..a1ccd95da8bb 100644 --- a/sound/soc/sof/intel/hda.c +++ b/sound/soc/sof/intel/hda.c @@ -1312,22 +1312,8 @@ struct snd_soc_acpi_mach *hda_machine_select(struct snd_sof_dev *sdev) /* report to machine driver if any DMICs are found */ mach->mach_params.dmic_num = check_dmic_num(sdev); - if (sdw_mach_found) { - /* - * DMICs use up to 4 pins and are typically pin-muxed with SoundWire - * link 2 and 3, or link 1 and 2, thus we only try to enable dmics - * if all conditions are true: - * a) 2 or fewer links are used by SoundWire - * b) the NHLT table reports the presence of microphones - */ - if (hweight_long(mach->link_mask) <= 2) - dmic_fixup = true; - else - mach->mach_params.dmic_num = 0; - } else { - if (mach->tplg_quirk_mask & SND_SOC_ACPI_TPLG_INTEL_DMIC_NUMBER) - dmic_fixup = true; - } + if (sdw_mach_found || mach->tplg_quirk_mask & SND_SOC_ACPI_TPLG_INTEL_DMIC_NUMBER) + dmic_fixup = true; if (tplg_fixup && dmic_fixup && From 4bcef04ca67fa8c46591a211885bb9c37f25dbbd Mon Sep 17 00:00:00 2001 From: Bard Liao Date: Tue, 25 Feb 2025 17:37:16 +0800 Subject: [PATCH 5/7] ASoC: Intel: sof_sdw: warn both sdw and pch dmic are used MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Typically, SoundWire MIC and PCH DMIC will not coexist. However, we may want to use both of them in some special cases. Add a warning to let users know that SoundWire MIC and PCH DMIC are both present and they could overwrite it with kernel params. Signed-off-by: Bard Liao Reviewed-by: Ranjani Sridharan Reviewed-by: Péter Ujfalusi Link: https://patch.msgid.link/20250225093716.67240-3-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown --- sound/soc/intel/boards/sof_sdw.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/sound/soc/intel/boards/sof_sdw.c b/sound/soc/intel/boards/sof_sdw.c index 203b07d4d833..c13064c77726 100644 --- a/sound/soc/intel/boards/sof_sdw.c +++ b/sound/soc/intel/boards/sof_sdw.c @@ -803,7 +803,9 @@ static int create_sdw_dailink(struct snd_soc_card *card, int *be_id, struct snd_soc_codec_conf **codec_conf) { struct device *dev = card->dev; + struct snd_soc_acpi_mach *mach = dev_get_platdata(card->dev); struct asoc_sdw_mc_private *ctx = snd_soc_card_get_drvdata(card); + struct snd_soc_acpi_mach_params *mach_params = &mach->mach_params; struct intel_mc_ctx *intel_ctx = (struct intel_mc_ctx *)ctx->private; struct asoc_sdw_endpoint *sof_end; int stream; @@ -900,6 +902,11 @@ static int create_sdw_dailink(struct snd_soc_card *card, codecs[j].name = sof_end->codec_name; codecs[j].dai_name = sof_end->dai_info->dai_name; + if (sof_end->dai_info->dai_type == SOC_SDW_DAI_TYPE_MIC && + mach_params->dmic_num > 0) { + dev_warn(dev, + "Both SDW DMIC and PCH DMIC are present, if incorrect, please set kernel params snd_sof_intel_hda_generic dmic_num=0 to disable PCH DMIC\n"); + } j++; } From fe08b7d5085a9774abc30c26d5aebc5b9cdd6091 Mon Sep 17 00:00:00 2001 From: Richard Fitzgerald Date: Tue, 25 Feb 2025 13:18:42 +0000 Subject: [PATCH 6/7] firmware: cs_dsp: Remove async regmap writes Change calls to async regmap write functions to use the normal blocking writes so that the cs35l56 driver can use spi_bus_lock() to gain exclusive access to the SPI bus. As this is part of a fix, it makes only the minimal change to swap the functions to the blocking equivalents. There's no need to risk reworking the buffer allocation logic that is now partially redundant. The async writes are a 12-year-old workaround for inefficiency of synchronous writes in the SPI subsystem. The SPI subsystem has since been changed to avoid the overheads, so this workaround should not be necessary. The cs35l56 driver needs to use spi_bus_lock() prevent bus activity while it is soft-resetting the cs35l56. But spi_bus_lock() is incompatible with spi_async() calls, which will fail with -EBUSY. Fixes: 8a731fd37f8b ("ASoC: cs35l56: Move utility functions to shared file") Signed-off-by: Richard Fitzgerald Link: https://patch.msgid.link/20250225131843.113752-2-rf@opensource.cirrus.com Signed-off-by: Mark Brown --- drivers/firmware/cirrus/cs_dsp.c | 24 ++++++------------------ 1 file changed, 6 insertions(+), 18 deletions(-) diff --git a/drivers/firmware/cirrus/cs_dsp.c b/drivers/firmware/cirrus/cs_dsp.c index 5365e9a43000..42433c19eb30 100644 --- a/drivers/firmware/cirrus/cs_dsp.c +++ b/drivers/firmware/cirrus/cs_dsp.c @@ -1609,8 +1609,8 @@ static int cs_dsp_load(struct cs_dsp *dsp, const struct firmware *firmware, goto out_fw; } - ret = regmap_raw_write_async(regmap, reg, buf->buf, - le32_to_cpu(region->len)); + ret = regmap_raw_write(regmap, reg, buf->buf, + le32_to_cpu(region->len)); if (ret != 0) { cs_dsp_err(dsp, "%s.%d: Failed to write %d bytes at %d in %s: %d\n", @@ -1625,12 +1625,6 @@ static int cs_dsp_load(struct cs_dsp *dsp, const struct firmware *firmware, regions++; } - ret = regmap_async_complete(regmap); - if (ret != 0) { - cs_dsp_err(dsp, "Failed to complete async write: %d\n", ret); - goto out_fw; - } - if (pos > firmware->size) cs_dsp_warn(dsp, "%s.%d: %zu bytes at end of file\n", file, regions, pos - firmware->size); @@ -1638,7 +1632,6 @@ static int cs_dsp_load(struct cs_dsp *dsp, const struct firmware *firmware, cs_dsp_debugfs_save_wmfwname(dsp, file); out_fw: - regmap_async_complete(regmap); cs_dsp_buf_free(&buf_list); if (ret == -EOVERFLOW) @@ -2326,8 +2319,8 @@ static int cs_dsp_load_coeff(struct cs_dsp *dsp, const struct firmware *firmware cs_dsp_dbg(dsp, "%s.%d: Writing %d bytes at %x\n", file, blocks, le32_to_cpu(blk->len), reg); - ret = regmap_raw_write_async(regmap, reg, buf->buf, - le32_to_cpu(blk->len)); + ret = regmap_raw_write(regmap, reg, buf->buf, + le32_to_cpu(blk->len)); if (ret != 0) { cs_dsp_err(dsp, "%s.%d: Failed to write to %x in %s: %d\n", @@ -2339,10 +2332,6 @@ static int cs_dsp_load_coeff(struct cs_dsp *dsp, const struct firmware *firmware blocks++; } - ret = regmap_async_complete(regmap); - if (ret != 0) - cs_dsp_err(dsp, "Failed to complete async write: %d\n", ret); - if (pos > firmware->size) cs_dsp_warn(dsp, "%s.%d: %zu bytes at end of file\n", file, blocks, pos - firmware->size); @@ -2350,7 +2339,6 @@ static int cs_dsp_load_coeff(struct cs_dsp *dsp, const struct firmware *firmware cs_dsp_debugfs_save_binname(dsp, file); out_fw: - regmap_async_complete(regmap); cs_dsp_buf_free(&buf_list); if (ret == -EOVERFLOW) @@ -2561,8 +2549,8 @@ static int cs_dsp_adsp2_enable_core(struct cs_dsp *dsp) { int ret; - ret = regmap_update_bits_async(dsp->regmap, dsp->base + ADSP2_CONTROL, - ADSP2_SYS_ENA, ADSP2_SYS_ENA); + ret = regmap_update_bits(dsp->regmap, dsp->base + ADSP2_CONTROL, + ADSP2_SYS_ENA, ADSP2_SYS_ENA); if (ret != 0) return ret; From 769c1b79295c38d60fde4c0a8f5f31e01360c54f Mon Sep 17 00:00:00 2001 From: Richard Fitzgerald Date: Tue, 25 Feb 2025 13:18:43 +0000 Subject: [PATCH 7/7] ASoC: cs35l56: Prevent races when soft-resetting using SPI control When SPI is used for control, the driver must hold the SPI bus lock while issuing the sequence of writes to perform a soft reset. >From the time the driver writes the SYSTEM_RESET command until the driver does a write to terminate the reset, there must not be any activity on the SPI bus lines. If there is any SPI activity during the soft-reset, another soft-reset will be triggered. The state of the SPI chip select is irrelevant. A repeated soft-reset does not in itself cause any problems, and it is not an infinite loop. The problem is a race between these resets and the driver polling for boot completion. There is a time window between soft resets where the driver could read HALO_STATE as 2 (fully booted) while the chip is actually soft-resetting. Although this window is small, it is long enough that it is possible to hit it in normal operation. To prevent this race and ensure the chip really is fully booted, the driver calls spi_bus_lock() to prevent other activity while resetting. It then issues the SYSTEM_RESET mailbox command. After allowing sufficient time for reset to take effect, the driver issues a PING mailbox command, which will force completion of the full soft-reset sequence. The SPI bus lock can then be released. The mailbox is checked for any boot or wakeup response from the firmware, before the value in HALO_STATE will be trusted. This does not affect SoundWire or I2C control. Fixes: 8a731fd37f8b ("ASoC: cs35l56: Move utility functions to shared file") Signed-off-by: Richard Fitzgerald Link: https://patch.msgid.link/20250225131843.113752-3-rf@opensource.cirrus.com Signed-off-by: Mark Brown --- include/sound/cs35l56.h | 31 ++++++++++++ sound/pci/hda/cs35l56_hda_spi.c | 3 ++ sound/soc/codecs/cs35l56-shared.c | 80 +++++++++++++++++++++++++++++++ sound/soc/codecs/cs35l56-spi.c | 3 ++ 4 files changed, 117 insertions(+) diff --git a/include/sound/cs35l56.h b/include/sound/cs35l56.h index 3dc7a1551ac3..5d653a3491d0 100644 --- a/include/sound/cs35l56.h +++ b/include/sound/cs35l56.h @@ -12,6 +12,7 @@ #include #include #include +#include #include #define CS35L56_DEVID 0x0000000 @@ -61,6 +62,7 @@ #define CS35L56_IRQ1_MASK_8 0x000E0AC #define CS35L56_IRQ1_MASK_18 0x000E0D4 #define CS35L56_IRQ1_MASK_20 0x000E0DC +#define CS35L56_DSP_MBOX_1_RAW 0x0011000 #define CS35L56_DSP_VIRTUAL1_MBOX_1 0x0011020 #define CS35L56_DSP_VIRTUAL1_MBOX_2 0x0011024 #define CS35L56_DSP_VIRTUAL1_MBOX_3 0x0011028 @@ -224,6 +226,7 @@ #define CS35L56_HALO_STATE_SHUTDOWN 1 #define CS35L56_HALO_STATE_BOOT_DONE 2 +#define CS35L56_MBOX_CMD_PING 0x0A000000 #define CS35L56_MBOX_CMD_AUDIO_PLAY 0x0B000001 #define CS35L56_MBOX_CMD_AUDIO_PAUSE 0x0B000002 #define CS35L56_MBOX_CMD_AUDIO_REINIT 0x0B000003 @@ -254,6 +257,16 @@ #define CS35L56_NUM_BULK_SUPPLIES 3 #define CS35L56_NUM_DSP_REGIONS 5 +/* Additional margin for SYSTEM_RESET to control port ready on SPI */ +#define CS35L56_SPI_RESET_TO_PORT_READY_US (CS35L56_CONTROL_PORT_READY_US + 2500) + +struct cs35l56_spi_payload { + __be32 addr; + __be16 pad; + __be32 value; +} __packed; +static_assert(sizeof(struct cs35l56_spi_payload) == 10); + struct cs35l56_base { struct device *dev; struct regmap *regmap; @@ -269,6 +282,7 @@ struct cs35l56_base { s8 cal_index; struct cirrus_amp_cal_data cal_data; struct gpio_desc *reset_gpio; + struct cs35l56_spi_payload *spi_payload_buf; }; static inline bool cs35l56_is_otp_register(unsigned int reg) @@ -276,6 +290,23 @@ static inline bool cs35l56_is_otp_register(unsigned int reg) return (reg >> 16) == 3; } +static inline int cs35l56_init_config_for_spi(struct cs35l56_base *cs35l56, + struct spi_device *spi) +{ + cs35l56->spi_payload_buf = devm_kzalloc(&spi->dev, + sizeof(*cs35l56->spi_payload_buf), + GFP_KERNEL | GFP_DMA); + if (!cs35l56->spi_payload_buf) + return -ENOMEM; + + return 0; +} + +static inline bool cs35l56_is_spi(struct cs35l56_base *cs35l56) +{ + return IS_ENABLED(CONFIG_SPI_MASTER) && !!cs35l56->spi_payload_buf; +} + extern const struct regmap_config cs35l56_regmap_i2c; extern const struct regmap_config cs35l56_regmap_spi; extern const struct regmap_config cs35l56_regmap_sdw; diff --git a/sound/pci/hda/cs35l56_hda_spi.c b/sound/pci/hda/cs35l56_hda_spi.c index d4ee5bb7c486..903578466905 100644 --- a/sound/pci/hda/cs35l56_hda_spi.c +++ b/sound/pci/hda/cs35l56_hda_spi.c @@ -22,6 +22,9 @@ static int cs35l56_hda_spi_probe(struct spi_device *spi) return -ENOMEM; cs35l56->base.dev = &spi->dev; + ret = cs35l56_init_config_for_spi(&cs35l56->base, spi); + if (ret) + return ret; #ifdef CS35L56_WAKE_HOLD_TIME_US cs35l56->base.can_hibernate = true; diff --git a/sound/soc/codecs/cs35l56-shared.c b/sound/soc/codecs/cs35l56-shared.c index e0ed4fc11155..e28bfefa72f3 100644 --- a/sound/soc/codecs/cs35l56-shared.c +++ b/sound/soc/codecs/cs35l56-shared.c @@ -10,6 +10,7 @@ #include #include #include +#include #include #include @@ -303,6 +304,79 @@ void cs35l56_wait_min_reset_pulse(void) } EXPORT_SYMBOL_NS_GPL(cs35l56_wait_min_reset_pulse, "SND_SOC_CS35L56_SHARED"); +static const struct { + u32 addr; + u32 value; +} cs35l56_spi_system_reset_stages[] = { + { .addr = CS35L56_DSP_VIRTUAL1_MBOX_1, .value = CS35L56_MBOX_CMD_SYSTEM_RESET }, + /* The next write is necessary to delimit the soft reset */ + { .addr = CS35L56_DSP_MBOX_1_RAW, .value = CS35L56_MBOX_CMD_PING }, +}; + +static void cs35l56_spi_issue_bus_locked_reset(struct cs35l56_base *cs35l56_base, + struct spi_device *spi) +{ + struct cs35l56_spi_payload *buf = cs35l56_base->spi_payload_buf; + struct spi_transfer t = { + .tx_buf = buf, + .len = sizeof(*buf), + }; + struct spi_message m; + int i, ret; + + for (i = 0; i < ARRAY_SIZE(cs35l56_spi_system_reset_stages); i++) { + buf->addr = cpu_to_be32(cs35l56_spi_system_reset_stages[i].addr); + buf->value = cpu_to_be32(cs35l56_spi_system_reset_stages[i].value); + spi_message_init_with_transfers(&m, &t, 1); + ret = spi_sync_locked(spi, &m); + if (ret) + dev_warn(cs35l56_base->dev, "spi_sync failed: %d\n", ret); + + usleep_range(CS35L56_SPI_RESET_TO_PORT_READY_US, + 2 * CS35L56_SPI_RESET_TO_PORT_READY_US); + } +} + +static void cs35l56_spi_system_reset(struct cs35l56_base *cs35l56_base) +{ + struct spi_device *spi = to_spi_device(cs35l56_base->dev); + unsigned int val; + int read_ret, ret; + + /* + * There must not be any other SPI bus activity while the amp is + * soft-resetting. + */ + ret = spi_bus_lock(spi->controller); + if (ret) { + dev_warn(cs35l56_base->dev, "spi_bus_lock failed: %d\n", ret); + return; + } + + cs35l56_spi_issue_bus_locked_reset(cs35l56_base, spi); + spi_bus_unlock(spi->controller); + + /* + * Check firmware boot by testing for a response in MBOX_2. + * HALO_STATE cannot be trusted yet because the reset sequence + * can leave it with stale state. But MBOX is reset. + * The regmap must remain in cache-only until the chip has + * booted, so use a bypassed read. + */ + ret = read_poll_timeout(regmap_read_bypassed, read_ret, + (val > 0) && (val < 0xffffffff), + CS35L56_HALO_STATE_POLL_US, + CS35L56_HALO_STATE_TIMEOUT_US, + false, + cs35l56_base->regmap, + CS35L56_DSP_VIRTUAL1_MBOX_2, + &val); + if (ret) { + dev_err(cs35l56_base->dev, "SPI reboot timed out(%d): MBOX2=%#x\n", + read_ret, val); + } +} + static const struct reg_sequence cs35l56_system_reset_seq[] = { REG_SEQ0(CS35L56_DSP1_HALO_STATE, 0), REG_SEQ0(CS35L56_DSP_VIRTUAL1_MBOX_1, CS35L56_MBOX_CMD_SYSTEM_RESET), @@ -315,6 +389,12 @@ void cs35l56_system_reset(struct cs35l56_base *cs35l56_base, bool is_soundwire) * accesses other than the controlled system reset sequence below. */ regcache_cache_only(cs35l56_base->regmap, true); + + if (cs35l56_is_spi(cs35l56_base)) { + cs35l56_spi_system_reset(cs35l56_base); + return; + } + regmap_multi_reg_write_bypassed(cs35l56_base->regmap, cs35l56_system_reset_seq, ARRAY_SIZE(cs35l56_system_reset_seq)); diff --git a/sound/soc/codecs/cs35l56-spi.c b/sound/soc/codecs/cs35l56-spi.c index c101134e8532..ca6c03a8766d 100644 --- a/sound/soc/codecs/cs35l56-spi.c +++ b/sound/soc/codecs/cs35l56-spi.c @@ -33,6 +33,9 @@ static int cs35l56_spi_probe(struct spi_device *spi) cs35l56->base.dev = &spi->dev; cs35l56->base.can_hibernate = true; + ret = cs35l56_init_config_for_spi(&cs35l56->base, spi); + if (ret) + return ret; ret = cs35l56_common_probe(cs35l56); if (ret != 0)