In the transcoder port sync mode, the slave transcoders mask their vblanks
until master transcoder's vblank so while disabling them, make
sure slaves are disabled first and then the masters.
v5:
* Dont pass dev priv to get_slave_crtc (Ville)
v4:
* Obtain slave state from master (Maarten)
v3:
* Rebase
v2:
* Use the intel_old_crtc_state_disables() helper
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-6-manasi.d.navare@intel.com
This clears the transcoder port sync bits of the TRANS_DDI_FUNC_CTL2
register during crtc_disable().
v3:
* Rebase on maarten's patches
v2:
* Directly write the trans_port_sync reg value (Maarten)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-5-manasi.d.navare@intel.com
As per the display enable sequence, we need to follow the enable sequence
for slaves first with DP_TP_CTL set to Idle and configure the transcoder
port sync register to select the corersponding master, then follow the
enable sequence for master leaving DP_TP_CTL to idle.
At this point the transcoder port sync mode is configured and enabled
and the Vblanks of both ports are synchronized so then set DP_TP_CTL
for the slave and master to Normal and do post crtc enable updates.
v11:
* Rebase (Manasi)
v10:
* in trans sync mode, dont stop link train for tgl (Manasi)
v9:
Remove update_scanline_offset to rebase on Maarten's patch (Manasi)
v8:
* Rebase on Maarten's patches (Manasi)
v7:
* Use ffs(slaves) to get slave crtc (Ville)
v6:
* Modeset implies active_changed, remove one condition (Maarten)
v5:
* Fix checkpatch warning (Manasi)
v4:
* Reuse skl_commit_modeset_enables() hook (Maarten)
* Obtain slave crtc and states from master (Maarten)
v3:
* Rebase on drm-tip (Manasi)
v2:
* Create a icl_update_crtcs hook (Maarten, Danvet)
* This sequence only for CRTCs in trans port sync mode (Maarten)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-4-manasi.d.navare@intel.com
After the state is committed, we readout the HW registers and compare
the HW state with the SW state that we just committed.
For Transcdoer port sync, we add master_transcoder and the
salves bitmask to the crtc_state, hence we need to read those during
the HW state readout to avoid pipe state mismatch.
v11:
* Move master trans init to get pipe_Config hooks (Ville)
v10:
* Initialize master_tarnscoder readout for all platforms (Ville)
v9:
* Initialize master_transcoder = INVALID at get config (Ville)
v8:
* Use master_select -1, address TRANS_EDP case (Ville)
* Rename master_transcoder to _readout (Lucas)
v7:
* NDont read HW state for DSI
v6:
* Go through both parts of HW readout (Maarten)
* Add a WARN if the same trans configured as
master and slave (Ville, Maarten)
v5:
* Add return INVALID in defaut case (Maarten)
v4:
* Get power domains in master loop for get_config (Ville)
v3:
* Add TRANSCODER_D (Maarten)
* v3 Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
v2:
* Add Transcoder_D and MISSING_CASE (Maarten)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-3-manasi.d.navare@intel.com
In case of tiled displays where different tiles are displayed across
different ports, we need to synchronize the transcoders involved.
This patch implements the transcoder port sync feature for
synchronizing one master transcoder with one or more slave
transcoders. This is only enbaled in slave transcoder
and the master transcoder is unaware that it is operating
in this mode.
This has been tested with tiled display connected to ICL.
v7:
* Rebase on Maarten's patches
v6:
* Use master_trans +1 and address missing trans_edp case (Ville)
v5:
* Add TRANSCODER_D case and MISSING_CASE (Maarten)
v4:
Rebase
v3:
* Check of DP_MST moved to atomic_check (Maarten)
v2:
* Do not use RMW, just write to the register in commit (Jani N)
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-2-manasi.d.navare@intel.com
In case of tiled displays when the two tiles are sent across two CRTCs
over two separate DP SST connectors, we need a mechanism to synchronize
the two CRTCs and their corresponding transcoders.
So use the master-slave mode where there is one master corresponding
to last horizontal and vertical tile that needs to be genlocked with
all other slave tiles.
This patch identifies saves the master transcoder in all the slave
CRTC states. This is needed to select the master CRTC/transcoder
while configuring transcoder port sync for the corresponding slaves.
v6:
Rebase (manasi)
v5:
* Address Ville's comments
* Just pass crtc_state, no need to check GEN (Ville)
v4:
* Rebase
v3:
* Use master_tramscoder instead of master_crtc for valid
HW state readouts (Ville)
v2:
* Move this to intel_mode_set_pipe_config(Jani N, Ville)
* Use slave_bitmask to save associated slaves in master crtc state (Ville)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-1-manasi.d.navare@intel.com
Replace the hand rolled stuff with drm_encoder_mask() when populating
possible_clones, and rename the function to
intel_encoder_possible_clones() to make it clear what it's used for.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-1-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Unlike other planes the cursor currently handles 180 degree rotation
adjustment during the hardware programming phase. Let's move that
stuff into intel_cursor_check_surface() to match how we do things
with other plane types.
And while at we'll plop in the final src x/y coordinates (which will
actually always be zero) into the src rect and color_plane[0].x/y,
just for some extra consistency.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015152757.12231-1-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Once we do the hw vs. uapi split we can no longer use
drm_atomic_helper_calc_timestamping_constants() as it'll
consult the uapi state instead of the hw state.
So let's just update the vblank timestamping constants whenever
we update the scanline offset. We use both to convert the hw
scanline count to something which matches the software timing
values.
First I thought to put these into intel_crtc_vblank_on() but
we may want to get the scanline counter value before that (eg.
from some early tracepoints), so let's stick to updating them
a bit earlier than intel_crtc_vblank_on().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191007114943.29307-3-ville.syrjala@linux.intel.com
While not all platforms allow us to change the cdclk frequency
we should still verify that the fixed cdclk frequency isn't
too low. To that end let's cook up a .modeset_calc_cdclk()
implementation that only does the min_cdclk vs. actual cdclk
frequency check for such platforms.
Also we mustn't forget about double wide pipe on gen2/3 when
doing this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708125325.16576-11-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We need to insert stuff between the plane and crtc .atomic_check()
drm_atomic_helper_check_planes() doesn't allow us to do that so
stop using it and hand roll the loops instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708125325.16576-9-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
When BT.2020 Colorimetry output is used for DP, we should program BT.2020
Colorimetry to MSA and VSC SDP. In order to handle colorspace of
drm_connector_state, it moves a calling of intel_ddi_set_pipe_settings()
function into intel_ddi_pre_enable_dp(). And it also rename
intel_ddi_set_pipe_settings() to intel_ddi_set_dp_msa().
As per DP 1.4a spec section 2.2.4 [MSA Data Transport]
The MSA data that the DP Source device transports for reproducing the main
video stream. Attribute data is sent once per frame during the main video
stream’s vertical blanking period.
In order to distinguish needed colorimetry for VSC SDP, it adds
intel_dp_needs_vsc_sdp function.
If the output colorspace requires vsc sdp or output format is YCbCr 4:2:0,
it uses MSA with VSC SDP.
As per DP 1.4a spec section 2.2.4.3 [MSA Field for Indication of
Color Encoding Format and Content Color Gamut] while sending
BT.2020 Colorimetry signals we should program MSA MISC1 fields which
indicate VSC SDP for the Pixel Encoding/Colorimetry Format.
v2: Remove useless parentheses
v3: Addressed review comments from Ville
- In order to checking output format and output colorspace on
intel_dp_needs_vsc_sdp(), it passes entire intel_crtc_state struct
value.
- Remove a pointless variable.
v9: Addressed review comments from Ville
- Remove a duplicated output color space from intel_crtc_state.
- In order to handle colorspace of drm_connector_state, it moves a
calling of intel_ddi_set_pipe_settings() function into
intel_ddi_pre_enable_dp().
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190919195311.13972-3-gwan-gyeong.mun@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Just a parameter rename,
drivers/gpu/drm/i915/display/intel_display.c:14425: warning: Function parameter or member '_new_plane_state' not described in 'intel_prepare_plane_fb'
drivers/gpu/drm/i915/display/intel_display.c:14425: warning: Excess function parameter 'new_state' description in 'intel_prepare_plane_fb'
drivers/gpu/drm/i915/display/intel_display.c:14534: warning: Function parameter or member '_old_plane_state' not described in 'intel_cleanup_plane_fb'
drivers/gpu/drm/i915/display/intel_display.c:14534: warning: Excess function parameter 'old_state' description in 'intel_cleanup_plane_fb'
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191012080208.18774-1-chris@chris-wilson.co.uk
We have a src and dect rectangle, use it instead of relying on
the core drm properties.
Because the core by default clips the src/dst properties, after
the drm_atomic_helper_check_plane_state() we manually set the
unclipped src/dst rectangles. We still need the call for
visibility checks, but this way we are able to use the src/dst
rects in the check/commit code.
This removes the special case in the watermark code for cursor w/h.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004113514.17064-5-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[mlankhorst: Clarify commit message to state we use unclipped src/dst
This can all be done from the intel_update_crtc function. Split out the
pipe update into a separate function, just like is done for the planes.
Pull in all the changes done during fastset as well. It makes no sense
for it to still exist as a separate function.
Changes since v1:
- Inline intel_update_pipe_config()
Changes since v2:
- Add comments suggested by matt.
- Reorder commit_pipe_config() to remove all nesting. (Ville, Matt)
- Use intel_set_pipe_src_size((). (Matt)
Changes since v3:
- Move atomic_update_watermarks closer to the plane calls.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004113514.17064-7-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[mlankhorst: Replace 8 spaces with tabs in comment]
We need to look at the hw fb in the plane split, so replace all the places
that use drm_plane_state with intel_plane_state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004113514.17064-6-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[mlankhorst: Fix line wraps (Matt Roper)]
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
DC3CO enabling B.Specs sequence requires to enable end configure
exit scanlines to TRANS_EXITLINE register, programming this register
has to be part of modeset sequence as this can't be change when
transcoder or port is enabled.
When system boots with only eDP panel there may not be real
modeset as BIOS has already programmed the necessary registers,
therefore it needs to force a modeset to enable and configure
DC3CO exitline.
v1: Computing dc3co_exitline crtc state from a DP encoder
compute config. [Imre]
Enabling and disabling DC3CO PSR2 transcoder exitline from
encoder pre_enable and post_disable hooks. [Imre]
Computing dc3co_exitline instead of has_dc3co_exitline bool. [Imre]
v2: Code refactoring for symmetry and to avoid exported function. [Imre]
Removing IS_TIGERLAKE check from compute_config, adding PIPE_A
restriction and clearing dc3co_exitline state if crtc is not active
or it is not PSR2 capable in dc3co exitline compute_config. [Imre]
Using GEN >= 12 check in dc3co exitline get_config. [Imre]
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003081738.22101-5-anshuman.gupta@intel.com
Pair the gmbus setup and teardown in the same layer. This also fixes the
double gmbus teardown on the i915_driver_modeset_probe() error path.
Move the gmbus setup a bit later in the sequence to make the follow-up
refactoring easier, and to pinpoint any unexpected consequences of this
change right here, instead of the later refactoring.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004122019.12009-3-jani.nikula@intel.com
Our other backends return an actual error value upon failure. Do the
same for stolen objects, which currently just return NULL on failure.
Signed-off-by: CQ Tang <cq.tang@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004170452.15410-2-matthew.auld@intel.com
The current "disable C3+" workaround for the delayed vblank
irqs on i945gm no longer works. I'm not sure what changed, but
now I need to also disable C2. I also got my hands on a i915gm
machine that suffers from the same issue.
After some furious poking of registers I managed to find a
better workaround: The "Do not Turn off Core Render Clock in C
states" bit. With that I no longer have to disable any C-states,
and as a nice bonus the power cost is only ~1/4 of the
"disable C3+" method (which mind you doesn't even work anymore,
and so would have an even higher power cost if we made it work
by also disabling C2).
So let's throw out all the cpuidle/qos crap and just toggle
the magic bit as needed. And we extend the workaround to cover
i915gm as well.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003140231.24408-1-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Replace the struct_mutex requirement for pinning the i915_vma with the
local vm->mutex instead. Note that the vm->mutex is tainted by the
shrinker (we require unbinding from inside fs-reclaim) and so we cannot
allocate while holding that mutex. Instead we have to preallocate
workers to do allocate and apply the PTE updates after we have we
reserved their slot in the drm_mm (using fences to order the PTE writes
with the GPU work and with later unbind).
In adding the asynchronous vma binding, one subtle requirement is to
avoid coupling the binding fence into the backing object->resv. That is
the asynchronous binding only applies to the vma timeline itself and not
to the pages as that is a more global timeline (the binding of one vma
does not need to be ordered with another vma, nor does the implicit GEM
fencing depend on a vma, only on writes to the backing store). Keeping
the vma binding distinct from the backing store timelines is verified by
a number of async gem_exec_fence and gem_exec_schedule tests. The way we
do this is quite simple, we keep the fence for the vma binding separate
and only wait on it as required, and never add it to the obj->resv
itself.
Another consequence in reducing the locking around the vma is the
destruction of the vma is no longer globally serialised by struct_mutex.
A natural solution would be to add a kref to i915_vma, but that requires
decoupling the reference cycles, possibly by introducing a new
i915_mm_pages object that is own by both obj->mm and vma->pages.
However, we have not taken that route due to the overshadowing lmem/ttm
discussions, and instead play a series of complicated games with
trylocks to (hopefully) ensure that only one destruction path is called!
v2: Add some commentary, and some helpers to reduce patch churn.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004134015.13204-4-chris@chris-wilson.co.uk
Split out the code related to vga client and vgaarb all over the place
into new intel_vga.[ch]. No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001152506.7854-1-jani.nikula@intel.com
As we execute GPU resets on a gt/ basis, and use the intel_gt as the
primary for all other reset functions, also use it for the has-reset?
predicates. Gradually simplifying the churn of pointers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190927211749.2181-1-chris@chris-wilson.co.uk
Now that TC support was added, initialize DDIs.
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-4-jose.souza@intel.com
We had this as an optimization to not do a plane update, but we killed
it off because there are so many reasons we may have to do a plane
update or fastset that it's best to just assume everything changed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920114235.22411-6-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
There was a integer wraparound when mode_clock became too high,
and we didn't correct for the FEC overhead factor when dividing,
with the calculations breaking at HBR3.
As a result our calculated bpp was way too high, and the link width
limitation never came into effect.
Print out the resulting bpp calcululations as a sanity check, just
in case we ever have to debug it later on again.
We also used the wrong factor for FEC. While bspec mentions 2.4%,
all the calculations use 1/0.972261, and the same ratio should be
applied to data M/N as well, so use it there when FEC is enabled.
This fixes the FIFO underrun we are seeing with FEC enabled.
Changes since v2:
- Handle fec_enable in intel_link_compute_m_n, so only data M/N is adjusted. (Ville)
- Fix initial hardware readout for FEC. (Ville)
Changes since v3:
- Remove bogus fec_to_mode_clock. (Ville)
Changes since v4:
- Use the correct register for icl. (Ville)
- Split hw readout to a separate patch.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: d9218c8f6c ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")
Cc: <stable@vger.kernel.org> # v5.0+
Cc: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925082110.17439-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The i915 specific mode config init code is too specific and detailed to
have open in a high level function. Abstract away. No functional
changes.
v2: nest drm_mode_config_init() in the function too (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920185421.17822-5-jani.nikula@intel.com
The code is too specific and detailed to have open in a high level
function. Abstract away. As a drive-by improvement switch to using
enableddisabled() in logging and git rid of a redundant !!. No
functional changes.
v2: drop the !! while at it too (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920185421.17822-4-jani.nikula@intel.com
In general, prefer struct drm_i915_private * over struct drm_device *
when either will do. Rename the local variable to i915. Also propagate
to intel_hpd_poll_fini(). No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920185421.17822-3-jani.nikula@intel.com
On ILK-IVB the pipe colorspace is configured via PIPECONF
(as opposed to PIPEMISC in BDW+). Let's configure+readout
that stuff correctly.
Enabling YCbCr 4:4:4 output will now be a simple matter of
setting crtc_state->output_format appropriately in the encoder
.compute_config(). However, when we do that we must be
aware of the fact that YCbCr DP output doesn't seem to work
on ILK (resulting image is totally garbled), but on SNB+
it works fine. However HDMI YCbCr output does work correctly
even on ILK.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718145053.25808-13-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
On HSW the pipe colorspace is configured via PIPECONF
(as opposed to PIPEMISC in BDW+). Let's configure+readout
that stuff correctly.
Enabling YCbCr 4:4:4 output will now be a simple matter of
setting crtc_state->output_format appropriately in the encoder
.compute_config().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718145053.25808-10-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Make intel_get_crtc_ycbcr_config() simpler and rename it
to bdw_get_pipemisc_output_format() to better reflect what
it does.
Also toss in some comments to document that the 4:2:0 PIPECONF
bits are glk+ only. They are mbz on earlier platforms so reading
them unconditionally is safe however.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718145053.25808-9-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Since HSW the PIPECONF progressive vs. interlaced selection is done
with just two bits instead of the earlier three. Let's not look at the
extra bit on HSW+. Also gen2 doesn't support interlaced displays at all.
This is actually fine as is currently because the extra bit is mbz (as
are all three bits on gen2). But just to avoid mishaps in the future
if the bits get reused let's only look at what's properly defined.
v2: constify crtc_state
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718145053.25808-8-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Modern platforms allow the transcoders hdisplay/vdisplay to exceed the
planes' max resolution. This has the nasty implication that modes on the
connectors' mode list may not be usable when the user asks for a
fullscreen plane. Seeing as that is the most common use case it seems
prudent to filter out modes that don't allow for fullscreen planes to
be enabled.
Let's do that in the connetor .mode_valid() hook so that normally
such modes are kept hidden but the user is still able to forcibly
specify such a mode if they know they don't need fullscreen planes.
This is in line with ealier policies regarding certain clock limits.
The idea is to prevent the casual user from encountering a mode that
would fail under typical conditions, but allow the expert user to
force things if they so wish.
Maybe in the future we should consider automagically using two
planes when one can't cover the entire screen? Wouldn't be a
great match for the current uapi with explicit planes though,
but I guess no worse than using two pipes (which we apparently
have to in the future anyway). Either that or we'd have to
teach userspace to do it for us.
v2: Fix icl+ max plane heigth (Manasi)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Leho Kraav <leho@kraav.com>
Cc: Sean Paul <sean@poorly.run>
Cc: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190918150707.32420-1-ville.syrjala@linux.intel.com
The officially validated plane width limit is 4k on skl+, however
we already had people using 5k displays before we started to enforce
the limit. Also it seems Windows allows 5k resolutions as well
(though not sure if they do it with one plane or two).
According to hw folks 5k should work with the possible
exception of the following features:
- Ytile (already limited to 4k)
- FP16 (already limited to 4k)
- render compression (already limited to 4k)
- KVMR sprite and cursor (don't care)
- horizontal panning (need to verify this)
- pipe and plane scaling (need to verify this)
So apart from last two items on that list we are already
fine. We should really verify what happens with those last
two items but I don't have a 5k display on hand atm so it'll
have to wait.
In the meantime let's just bump the limit back up to 5k since
several users have already been using it without apparent issues.
At least we'll be no worse off than we were prior to lowering
the limits.
Cc: stable@vger.kernel.org
Cc: Sean Paul <sean@poorly.run>
Cc: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Leho Kraav <leho@kraav.com>
Fixes: 372b9ffb57 ("drm/i915: Fix skl+ max plane width")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111501
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190905135044.2001-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Sean Paul <sean@poorly.run>
