The source device should ensure the sink is ready before proceeding to
read the sink capability or perform any aux transactions. The sink
will indicate its readiness by asserting the HPD line. The controller
driver needs to wait for the hpd line to be asserted by the sink before
it performs any aux transactions.
The eDP sink is assumed to be always connected. It needs power from the
source and its HPD line will be asserted only after the panel is powered
on. The panel power will be enabled from the panel-edp driver and only
after that, the hpd line will be asserted.
Whereas for DP, the sink can be hotplugged and unplugged anytime. The hpd
line gets asserted to indicate the sink is connected and ready. Hence
there is no need to wait for the hpd line to be asserted for a DP sink.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/483312/
Link: https://lore.kernel.org/r/1650887072-16652-4-git-send-email-quic_sbillaka@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
If you happened to try to access `/dev/drm_dp_aux` devices provided by
the MSM DP AUX driver too early at bootup you could go boom. Let's
avoid that by only allowing AUX transfers when the controller is
powered up.
Specifically the crash that was seen (on Chrome OS 5.4 tree with
relevant backports):
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 0 PID: 3131 Comm: fwupd Not tainted 5.4.144-16620-g28af11b73efb #1
Hardware name: Google Lazor (rev3+) with KB Backlight (DT)
Call trace:
dump_backtrace+0x0/0x14c
show_stack+0x20/0x2c
dump_stack+0xac/0x124
panic+0x150/0x390
nmi_panic+0x80/0x94
arm64_serror_panic+0x78/0x84
do_serror+0x0/0x118
do_serror+0xa4/0x118
el1_error+0xbc/0x160
dp_catalog_aux_write_data+0x1c/0x3c
dp_aux_cmd_fifo_tx+0xf0/0x1b0
dp_aux_transfer+0x1b0/0x2bc
drm_dp_dpcd_access+0x8c/0x11c
drm_dp_dpcd_read+0x64/0x10c
auxdev_read_iter+0xd4/0x1c4
I did a little bit of tracing and found that:
* We register the AUX device very early at bootup.
* Power isn't actually turned on for my system until
hpd_event_thread() -> dp_display_host_init() -> dp_power_init()
* You can see that dp_power_init() calls dp_aux_init() which is where
we start allowing AUX channel requests to go through.
In general this patch is a bit of a bandaid but at least it gets us
out of the current state where userspace acting at the wrong time can
fully crash the system.
* I think the more proper fix (which requires quite a bit more
changes) is to power stuff on while an AUX transfer is
happening. This is like the solution we did for ti-sn65dsi86. This
might be required for us to move to populating the panel via the
DP-AUX bus.
* Another fix considered was to dynamically register / unregister. I
tried that at <https://crrev.com/c/3169431/3> but it got
ugly. Currently there's a bug where the pm_runtime() state isn't
tracked properly and that causes us to just keep registering more
and more.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211109100403.1.I4e23470d681f7efe37e2e7f1a6466e15e9bb1d72@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
Aux hardware calibration sequence requires resetting the aux controller
in order for the new setting to take effect. However resetting the AUX
controller will also clear HPD interrupt status which may accidentally
cause pending unplug interrupt to get lost. Therefore reset aux
controller only when link is in connection state when dp_aux_cmd_fifo_tx()
fail. This fixes Link Layer CTS cases 4.2.1.1 and 4.2.1.2.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1628196295-7382-4-git-send-email-khsieh@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Let's look at the irq status bits after a transfer and see if we got a
nack or a defer or a timeout, instead of telling drm layers that
everything was fine, while still printing an error message. I wasn't
sure about NACK+DEFER so I lumped all those various errors along with a
nack so that the drm core can figure out that things are just not going
well. The important thing is that we're now returning -ETIMEDOUT when
the message times out and nacks for bad addresses.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Cc: aravindh@codeaurora.org
Cc: Sean Paul <sean@poorly.run>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Kuogee Hsieh <khsieh@codeaurora.org>
Link: https://lore.kernel.org/r/20210507212505.1224111-4-swboyd@chromium.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
We don't need to hold the lock to inspect the message we're going to
transfer, and we don't need to clear the busy flag either. Take the lock
later and bail out earlier if conditions aren't met.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Cc: aravindh@codeaurora.org
Cc: Sean Paul <sean@poorly.run>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Kuogee Hsieh <khsieh@codeaurora.org>
Link: https://lore.kernel.org/r/20210507212505.1224111-3-swboyd@chromium.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
We don't need to stash away 'isr' in the aux structure to pass to two
functions. Let's use a local variable instead. And we can complete the
completion variable in one place instead of two to simplify the code.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Cc: aravindh@codeaurora.org
Cc: Sean Paul <sean@poorly.run>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Kuogee Hsieh <khsieh@codeaurora.org>
Link: https://lore.kernel.org/r/20210507212505.1224111-2-swboyd@chromium.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
In commit 9fc418430c ("drm/msm/dp: unplug interrupt missed after
irq_hpd handler") we dropped a reset of the aux phy during aux transfers
because resetting the phy during active communication caused us to miss
an hpd irq in some cases. Unfortunately, we also dropped the part of the
code that changes the aux phy tuning when an aux transfer fails due to a
timeout. That part of the code was calling into the phy driver to
reconfigure the aux TX swing controls, working around poor channel
quality. Let's restore this phy setting code so that aux channel
communication is more reliable.
Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Fixes: 9fc418430c ("drm/msm/dp: unplug interrupt missed after irq_hpd handler")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is HPD unplug interrupts missed at scenario of an irq_hpd
followed by unplug interrupts with around 10 ms in between.
Since both AUX_SW_RESET and DP_SW_RESET clear pending HPD interrupts,
irq_hpd handler should not issues either aux or sw reset to avoid
following unplug interrupt be cleared accidentally. This patch
also postpone handling of irq_hpd until connected state if it
happened at connection pending state.
Changes in V2:
-- add postpone handling of irq_hpd until connected state
-- check DP_TRAINING_1 instead of DP_TRAINING_NONE
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Make the necessary changes to the DP driver to use the qmp phy from the
common phy framework instead of rolling our own in the drm subsystem.
This also removes the PLL code and adds proper includes so things build.
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Rob Clark <robdclark@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
add event thread to execute events serially from event queue. Also
timeout mode is supported which allow an event be deferred to be
executed at later time. Both link and phy compliant tests had been
done successfully.
Changes in v2:
-- Fix potential deadlock by removing redundant connect_mutex
-- Check and enable link clock during modeset
-- Drop unused code and fix function prototypes.
-- set sink power to normal operation state (D0) before DPCD read
Changes in v3:
-- push idle pattern at main link before timing generator off
-- add timeout handles for both connect and disconnect
Changes in v4:
-- add ST_SUSPEND_PENDING to handles suspend/modeset test operations
-- clear dp phy aux interrupt status when ERR_DPPHY_AUX error
-- send segment addr during edid read
-- clear bpp depth before MISC register write
Changes in v5:
-- add ST_SUSPENDED to fix crash at resume
Changes in v6:
-- at msm_dp_display_enable() do not return until resume_done to avoid
kms commit timeout
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add the needed displayPort files to enable DP driver
on msm target.
"dp_display" module is the main module that calls into
other sub-modules. "dp_drm" file represents the interface
between DRM framework and DP driver.
Changes in v12:
-- Add support of pm ops in display port driver
-- Clear bpp depth bits before writing to MISC register
-- Fix edid read
Previous Change log:
https://lkml.kernel.org/lkml/20200818051137.21478-3-tanmay@codeaurora.org/
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Co-developed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Co-developed-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Co-developed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Co-developed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
