The downstream uses read-modify-write for updating command mode
compression registers. Let's follow this approach. This also fixes the
following warning:
drivers/gpu/drm/msm/dsi/dsi_host.c:918:23: warning: variable 'reg_ctrl' set but not used [-Wunused-but-set-variable]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/484305/
Link: https://lore.kernel.org/r/20220430175533.3817792-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
As noticed by Dan ([1] an the followup thread) there are multiple issues
with the return values for MSM DSI command transmission callback. In
the error case it can easily return a positive value when it should
have returned a proper error code.
This commits attempts to fix these issues both in TX and in RX paths.
[1]: https://lore.kernel.org/linux-arm-msm/20211001123617.GH2283@kili/
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/480501/
Link: https://lore.kernel.org/r/20220401231104.967193-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
When DSC is enabled, we need to configure DSI registers accordingly and
configure the respective stream compression registers.
Add support to calculate the register setting based on DSC params and
timing information and configure these registers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480934/
Link: https://lore.kernel.org/r/20220406094031.1027376-15-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add a mode valid callback for dsi_mgr for checking mode being valid in
case of DSC. For DSC the height and width needs to be multiple of slice,
so we check that here
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480930/
Link: https://lore.kernel.org/r/20220406094031.1027376-13-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
When DSC is enabled, we need to get the DSC parameters from the panel
driver, so add a dsc parameter in panel to fetch and pass DSC
configuration for DSI panels to DPU encoder, which will enable and
then configure DSC hardware blocks accordingly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480910/
Link: https://lore.kernel.org/r/20220406094031.1027376-3-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Config autodetect based on DSI controller version is quite limited
since several qcom SoCs can integrate a DSI controller with the same
version, but with different config (io_offset, supplies, etc).
This change allows to specify dsi config via device data pointer.
config autodetect is still used in case data pointer is NULL.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/474089/
Link: https://lore.kernel.org/r/1644853060-12222-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Quoting the header comments, IRQF_ONESHOT is "Used by threaded interrupts
which need to keep the irq line disabled until the threaded handler has
been run.". When applied to an interrupt that doesn't request a threaded
irq then IRQF_ONESHOT has a lesser known (undocumented?) side effect,
which it to disable the forced threading of irqs (and for "normal" kernels
it is a nop). In this case I can find no evidence that suppressing forced
threading is intentional. Had it been intentional then a driver must adopt
the raw_spinlock API in order to avoid deadlocks on PREEMPT_RT kernels
(and avoid calling any kernel API that uses regular spinlocks).
Fix this by removing the spurious additional flag.
This change is required for my Snapdragon 7cx Gen2 tablet to boot-to-GUI
with PREEMPT_RT enabled.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220201174734.196718-2-daniel.thompson@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
msm_ioremap() functions take additional argument dbgname which is now
unused.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20220105232700.444170-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
No functional change, as we only actually enable autosuspend for the GPU
device. But lets not encourage thinking that autosuspend is a good idea
for anything display related.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211215175910.1744151-1-robdclark@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is no reason to set clock parents manually, use device tree to
assign DSI/display clock parents to DSI PHY clocks. Dropping this manual
setup allows us to drop repeating code and to move registration of hw
clock providers to generic place.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20211006204828.1218225-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Move DPHY/CPHY setting from msm_dsi_host_set_src_pll() to new function
msm_dsi_host_set_phy_mode().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20211006204828.1218225-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
If "data_lanes" property of the dsi output endpoint is missing in
the DT, num_data_lanes would be 0 by default, which could cause
dsi_host_attach() to fail if dsi->lanes is set to a non-zero value
by the bridge driver.
According to the binding document of msm dsi controller, the
input/output endpoint of the controller is expected to have 4 lanes.
So let's set num_data_lanes to 4 by default.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211030100812.1.I6cd9af36b723fed277d34539d3b2ba4ca233ad2d@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
Switch to the documented order dsi-host vs bridge probe.
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Tested-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025151536.1048186-22-maxime@cerno.tech
Change byte_clk_rate, pixel_clk_rate, esc_clk_rate, and src_clk_rate
from u32 to unsigned long, since clk_get_rate() returns an unsigned long.
Fixes: a6bcddbc2e ("drm/msm: dsi: Handle dual-channel for 6G as well")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jessica Zhang <jesszhan@codeaurora.org>
Link: https://lore.kernel.org/r/20211020183438.32263-1-jesszhan@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jyri Sarha <jyri.sarha@iki.fi>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Link: https://lore.kernel.org/r/75e8ba40076ad707d47e3a3670e6b23c1b8b11bc.1633874223.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use clk_bulk_* API instead of hand-coding them. Note, this drops support
for legacy clk naming (e.g. "iface_clk" instead of just "iface"),
however all in-kernel device trees were converted long long ago. The
warning is present there since 2017.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211002012715.691406-1-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The DSI host might be left in some state by the bootloader. If this
state generates an IRQ, it might hang the system by holding the
interrupt line before the driver sets up the DSI host to the known
state.
Move the request_irq into msm_dsi_host_init and pass IRQF_NO_AUTOEN to
it. Call enable/disable_irq after msm_dsi_host_power_on/_off()
functions, so that we can be sure that the interrupt is delivered when
the host is in the known state.
It is not possible to defer the interrupt enablement to a later point,
because drm_panel_prepare might need to communicate with the panel over
the DSI link and that requires working interrupt.
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20211002010830.647416-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201231095616.25973-1-vulab@iscas.ac.cn
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This disables a lock which wasn't enabled and it does not disable
the first lock in the array.
Fixes: 6e0eb52eba ("drm/msm/dsi: Parse bus clocks from a list")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211001123409.GG2283@kili
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This is the main pull for v5.15, after the early pull request with
drm/scheduler conversion:
* New a6xx GPU support: a680 and 7c3
* dsi: 7nm phi, sc7280 support, test pattern generator support
* mdp4 fixes for older hw like the nexus7
* displayport fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGs_tyanTeDGMH1X+Uf4wdyy7jYj-CinGXXVETiYOESahw@mail.gmail.com
Unlike previous generations, 7nm PHYs are required to collaborate with
the host for continuos clock mode. Add changes neccessary to enable
continuous clock mode in the 7nm DSI PHYs.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210805170817.3337665-1-dmitry.baryshkov@linaro.org
[Fix merge conflict, and $description typo]
Signed-off-by: Rob Clark <robdclark@chromium.org>
We are preparing to support two independent DSI hosts in the DSI/DPU
code. To remove possible confusion (as both configurations can be
referenced as dual DSI) let's rename old "dual DSI" (two DSI hosts
driving single device, with clocks being locked) to "bonded DSI".
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210717124016.316020-2-dmitry.baryshkov@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[DB: add one extra hunk added by one previous patches]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
During board bringups its useful to have a DSI test pattern
generator to isolate a DPU vs a DSI issue and focus on the relevant
hardware block.
To facilitate this, add an API which triggers the DSI controller
test pattern. The expected output is a rectangular checkered pattern.
This has been validated on a single DSI video mode panel by calling it
right after drm_panel_enable() which is also the ideal location to use
this as the DSI host and the panel have been initialized by then.
Further validation on dual DSI and command mode panel is pending.
If there are any fix ups needed for those, it shall be applied on top
of this change.
Changes in v2:
- generate the new dsi.xml.h and update the bitfield names
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/1626922232-29105-2-git-send-email-abhinavk@codeaurora.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
None of supported devies uses "gdsc" regulator for DSI. GDSC support is
now implemented as a power domain. Drop old code and config handling
gdsc regulator requesting and enabling.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210701000015.3347713-1-dmitry.baryshkov@linaro.org
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add the required changes to support 7nm pll/phy in CPHY mode.
This adds a "qcom,dsi-phy-cphy-mode" property for the PHY node to enable
the CPHY mode.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210617144349.28448-4-jonathan@marek.ca
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Required bump from v5.13-rc3 to v5.14-rc3, and to pick up sysfb compilation fixes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Many of the DSI flags have names opposite to their actual effects,
e.g. MIPI_DSI_MODE_EOT_PACKET means that EoT packets will actually
be disabled. Fix this by including _NO_ in the flag names, e.g.
MIPI_DSI_MODE_NO_EOT_PACKET.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@samsung.com>
Reviewed-by: Xin Ji <xji@analogixsemi.com> # anx7625.c
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> # msm/dsi
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727094435.v3.1.I629b2366a6591410359c7fcf6d385b474b705ca2@changeid
Use resource-managed OPP API to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314163408.22292-12-digetx@gmail.com
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
msm_gem_get_vaddr() currently always maps as writecombine, so use the right
flag instead of relying on broken behavior (things don't actually work if
they are mapped as uncached).
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Link: https://lore.kernel.org/r/20210423190833.25319-3-jonathan@marek.ca
Signed-off-by: Rob Clark <robdclark@chromium.org>
Instead of looping throught the resources each time to get the DSI CTRL
area size, get it at the ioremap time.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210427001828.2375555-4-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Instead of always getting the disp_state from drm device, pass it as an
argument.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210427001828.2375555-2-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add an API to take a snapshot of DSI controller registers. This API
will be used by the msm_disp_snapshot module to capture the DSI
snapshot.
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1618606645-19695-4-git-send-email-abhinavk@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add the msm_disp_snapshot module which adds supports to dump dpu
registers and capture the drm atomic state which can be used in
case of error conditions.
changes in v5:
- start storing disp_state in msm_kms instead of dpu_kms
- get rid of MSM_DISP_SNAPSHOT_IN_* enum by simplifying the functions
- move snprintf inside the snapshot core by using varargs
- get rid of some stale code comments
- allow snapshot module for non-DPU targets
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1618606645-19695-3-git-send-email-abhinavk@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
All MSM DSI PHYs provide two clocks: byte and pixel ones.
Register/unregister provided clocks from the generic place, removing
boilerplate code from all MSM DSI PHY drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-11-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The only usage of dsi_host_ops is to assign its address to the ops field
in the mipi_dsi_host struct, which is a const pointer. Make it const to
allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
While at it, also create a label to put clkname.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We haven't sync'd for a while.. pull in updates to get definitions for
some fields in pkt7 payloads.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
On SDM845 and SC7180 DSI needs to express a performance state
requirement on a power domain depending on the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
dev_pm_opp_set_rate() is designed to be equivalent to clk_set_rate()
for devices without an OPP table, hence the change works fine
on devices/platforms which only need to set a clock rate.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Spelling out _unlocked for each and every driver is a annoying.
Especially if we consider how many drivers, do not know (or need to)
about the horror stories involving struct_mutex.
Just drop the suffix. It makes the API cleaner.
Done via the following script:
__from=drm_gem_object_put_unlocked
__to=drm_gem_object_put
for __file in $(git grep --name-only $__from); do
sed -i "s/$__from/$__to/g" $__file;
done
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200515095118.2743122-25-emil.l.velikov@gmail.com
LANE_CTRL register in latest version of DSI controller (v2.2)
has additional functionality introduced to enable/disable HS
signalling with default value set to enabled. To accommodate this
change, LANE_CTRL register should be read and bit wise ORed to enable
non continuous clock mode. Without this change, if register is written
directly, HS signalling will be disabled resulting in black screen.
Changes in v1:
-Update LANE_CTRL register value
Changes in v2:
-Changing commit message accordingly.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Decouple enable and rate setting. Prep work to handle bootloader
enabled display.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
+ OCMEM support to enable the couple generations that had shared OCMEM
rather than GMEM exclusively for the GPU (late a3xx and I think basically
all of a4xx). Bjorn and Brian decided to land this through the drm
tree to avoid having to coordinate merge requests.
+ a510 support, and various associated display support
+ the usual misc cleanups and fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CAF6AEGv-JWswEJRxe5AmnGQO1SZnpxK05kO1E29K6UUzC9GMMw@mail.gmail.com
On msm8998, vblank timeouts are observed because the DSI controller is not
reset properly, which ends up stalling the MDP. This is because the reset
logic is not correct per the hardware documentation.
The documentation states that after asserting reset, software should wait
some time (no indication of how long), or poll the status register until it
returns 0 before deasserting reset.
wmb() is insufficient for this purpose since it just ensures ordering, not
timing between writes. Since asserting and deasserting reset occurs on the
same register, ordering is already guaranteed by the architecture, making
the wmb extraneous.
Since we would define a timeout for polling the status register to avoid a
possible infinite loop, lets just use a static delay of 20 ms, since 16.666
ms is the time available to process one frame at 60 fps.
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Cc: Hai Li <hali@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Sean Paul <sean@poorly.run>
[seanpaul renamed RESET_DELAY to DSI_RESET_TOGGLE_DELAY_MS]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011133939.16551-1-jeffrey.l.hugo@gmail.com
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/msm/dsi/dsi_host.c: In function dsi_cmd_dma_rx:
drivers/gpu/drm/msm/dsi/dsi_host.c:1302:7: warning: variable lp set but not used [-Wunused-but-set-variable]
It is not used since commit a689554ba6 ("drm/msm:
Initial add DSI connector support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1570690506-83287-5-git-send-email-zhengbin13@huawei.com
