The clock and data lanes of the DSI PHY have a calibration circuitry
feature. As per the MSM DSI PHY tuning guidelines, the drive strength
tuning can be done by adjusting rescode offset for hstop/hsbot, and
the drive level tuning can be done by adjusting the LDO output level
for the HSTX drive.
Signed-off-by: Rajeev Nandan <quic_rajeevny@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1643573719-32095-4-git-send-email-quic_rajeevny@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
All DSI PHY/PLL drivers were referencing their VCO parent clock by a
global name, most of which don't exist or have been renamed. These
clock drivers seem to function fine without that except the 14nm driver
for sdm6xx [1].
At the same time all DTs provide a "ref" clock as per the requirements
of dsi-phy-common.yaml, but the clock is never used. This patchset puts
that clock to use without relying on a global clock name, so that all
dependencies are explicitly defined in DT (the firmware) in the end.
Note that this patch intentionally breaks older firmware (DT) that
relies on the clock to be found globally instead. The only affected
platform is msm8974 [2] for whose dsi_phy_28nm a .name="xo" fallback is
left in place to accommodate a more graceful transition period. All
other platforms had the "ref" clock added to their phy node since its
inception, or in a followup patch some time after. These patches
wrongly assumed that the "ref" clock was actively used and have hence
been listed as "Fixes:" below.
Furthermore apq8064 was providing the wrong 19.2MHz cxo instead of
27MHz pxo clock, which has been addressed in [3].
It is expected that both [2] and [3] are applied to the tree well in
advance of this patch such that any actual breakage is extremely
unlikely, but might still occur if kernel upgrades are performed without
the DT to match. After some time the fallback for msm8974 can be
removed again as well.
[1]: https://lore.kernel.org/linux-arm-msm/386db1a6-a1cd-3c7d-a88e-dc83f8a1be96@somainline.org/
[2]: https://lore.kernel.org/linux-arm-msm/20210830175739.143401-1-marijn.suijten@somainline.org/
[3]: https://lore.kernel.org/linux-arm-msm/20210829203027.276143-2-marijn.suijten@somainline.org/
Fixes: 79e51645a1 ("arm64: dts: qcom: msm8916: Set 'xo_board' as ref clock of the DSI PHY")
Fixes: 6969d1d9c6 ("ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY")
Fixes: 0c0e72705a ("arm64: dts: sdm845: Set 'bi_tcxo' as ref clock of the DSI PHYs")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210911131922.387964-2-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
We are preparing to support two independent DSI hosts in the DSI/DPU
code. To remove possible confusion (as both configurations can be
referenced as dual DSI) let's rename old "dual DSI" (two DSI hosts
driving single device, with clocks being locked) to "bonded DSI".
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210717124016.316020-2-dmitry.baryshkov@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[DB: add one extra hunk added by one previous patches]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Based on mesa commit daa2ccff7a0201941db3901780d179e2634057d5
Small bit of .c churn in the phy code to adapt to split up of phy
related registers.
Signed-off-by: Rob Clark <robdclark@chromium.org>
A problem was reported on CoachZ devices where the display wouldn't come
up, or it would be distorted. It turns out that the PLL code here wasn't
getting called once dsi_pll_10nm_vco_recalc_rate() started returning the
same exact frequency, down to the Hz, that the bootloader was setting
instead of 0 when the clk was registered with the clk framework.
After commit 001d8dc338 ("drm/msm/dsi: remove temp data from global
pll structure") we use a hardcoded value for the parent clk frequency,
i.e. VCO_REF_CLK_RATE, and we also hardcode the value for FRAC_BITS,
instead of getting it from the config structure. This combination of
changes to the recalc function allows us to properly calculate the
frequency of the PLL regardless of whether or not the PLL has been
clk_prepare()d or clk_set_rate()d. That's a good improvement.
Unfortunately, this means that now we won't call down into the PLL clk
driver when we call clk_set_rate() because the frequency calculated in
the framework matches the frequency that is set in hardware. If the rate
is the same as what we want it should be OK to not call the set_rate PLL
op. The real problem is that the prepare op in this driver uses a
private struct member to stash away the vco frequency so that it can
call the set_rate op directly during prepare. Once the set_rate op is
never called because recalc_rate told us the rate is the same, we don't
set this private struct member before the prepare op runs, so we try to
call the set_rate function directly with a frequency of 0. This
effectively kills the PLL and configures it for a rate that won't work.
Calling set_rate from prepare is really quite bad and will confuse any
downstream clks about what the rate actually is of their parent. Fixing
that will be a rather large change though so we leave that to later.
For now, let's stash away the rate we calculate during recalc so that
the prepare op knows what frequency to set, instead of 0. This way
things keep working and the display can enable the PLL properly. In the
future, we should remove that code from the prepare op so that it
doesn't even try to call the set rate function.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Fixes: 001d8dc338 ("drm/msm/dsi: remove temp data from global pll structure")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210608195519.125561-1-swboyd@chromium.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Phy driver already knows the source PLL id basing on the set usecase and
the current PLL id. Stop passing it to the phy_enable call. As a
reminder, dsi manager will always use DSI 0 as a clock master in a slave
mode, so PLL 0 is always a clocksource for DSI 0 and it is always a
clocksource for DSI 1 too unless DSI 1 is used in the standalone mode.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-25-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The src_truthtable config is not used for some of phys, which use other
means of configuring the master/slave usecases. Inline this function
with the goal of removing src_pll_id argument in the next commit.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-24-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The 7nm, 10nm and 14nm drivers would store interim data used during
VCO/PLL rate setting in the global dsi_pll_Nnm structure. Move this data
structures to the onstack storage. While we are at it, drop
unused/static 'config' data, unused config fields, etc.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-23-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Drop duplicate fields pdev and id from dsi_pll_Nnm instances. Reuse
those fields from the provided msm_dsi_phy.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-22-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
All PHY drivers would map dsi_pll area. Some PHY drivers would also
map dsi_phy area again (a leftover from old PHY/PLL separation). Move
all ioremaps to the common dsi_phy driver code and drop individual
ioremapped areas from PHY drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-21-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Drop the struct msm_dsi_pll abstraction, by including vco's clk_hw
directly into struct msm_dsi_phy.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-19-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Make save_state/restore callbacks accept struct msm_dsi_phy rather than
struct msm_dsi_pll. This moves them to struct msm_dsi_phy_ops, allowing
us to drop struct msm_dsi_pll_ops.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-18-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
These drivers do not use vco_delay variable, so drop it from all of
them.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-15-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Morph msm_dsi_pll_save/restore_state() into msm_dsi_phy_save/restore_state(),
thus removing last bits of knowledge about msm_dsi_pll from dsi_manager.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-14-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use devres-enabled version of clock registration functions. This lets us
remove dsi_pll destroy callbacks completely.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-12-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
All MSM DSI PHYs provide two clocks: byte and pixel ones.
Register/unregister provided clocks from the generic place, removing
boilerplate code from all MSM DSI PHY drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-11-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
msm_dsi_pll_set_usecase() function is not used outside of individual DSI
PHY drivers, so drop it in favour of calling the the respective
set_usecase functions directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-10-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
With the current upstream driver the msm_dsi_phy_type enum does not make
much sense: all DSI PHYs are probed using the dt bindings, the phy type
is not passed between drivers. Use quirks in phy individual PHY drivers
to differentiate minor harware differences and drop the enum.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-8-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Move all PLL-related callbacks into struct msm_dsi_phy_cfg. This limits
the amount of data in the struct msm_dsi_pll.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-7-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Each phy version is tightly coupled with the corresponding PLL code,
there is no need to keep them separate. Fuse source files together in
order to simplify DSI code.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-5-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
DSI PHY init callback would either map dsi_phy_regulator or dsi_phy_lane
depending on the PHY type. Replace those callbacks with configuration
options governing mapping those regions.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-4-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Implement phy_disable() callback to disable DSI PHY lanes and blocks
when phy is not used.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: ff73ff1940 ("drm/msm/dsi: Populate the 10nm PHY funcs")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Clang warns:
drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c:80:6: warning: logical not is
only applied to the left hand side of this bitwise operator
[-Wlogical-not-parentheses]
if (!phy->cfg->quirks & V3_0_0_10NM_OLD_TIMINGS_QUIRK) {
^ ~
drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c:80:6: note: add parentheses
after the '!' to evaluate the bitwise operator first
if (!phy->cfg->quirks & V3_0_0_10NM_OLD_TIMINGS_QUIRK) {
^
( )
drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c:80:6: note: add parentheses
around left hand side expression to silence this warning
if (!phy->cfg->quirks & V3_0_0_10NM_OLD_TIMINGS_QUIRK) {
^
( )
1 warning generated.
Add parentheses around the bitwise AND so it is evaluated first then
negated.
Fixes: 3dbbf8f09e ("drm/msm/dsi: Add old timings quirk for 10nm phy")
Link: https://github.com/ClangBuiltLinux/linux/issues/547
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The v3.0.0 10nm phy has two different implementations between MSM8998 and
SDM845, which require different timings calculations. Unfortunately, the
hardware designers did not choose to revise the version to account for this
delta so implement a quirk instead.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The MSM8998 dsi phy is 10nm v3.0.0 like SDM845, however there appear to
be minor differences such as the address space location.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use DRM_DEV_INFO/ERROR/WARN instead of dev_info/err/debug to generate
drm-formatted specific log messages so that it will be easy to
differentiate in case of multiple instances of driver.
Signed-off-by: Mamta Shukla <mamtashukla555@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the DSI PHY timings are hard-coded for a specific panel
for the 10nm PHY.
Replace this with the auto PHY timing calculator which can calculate
the PHY timings for any panel.
Changes in v4:
- None
Changes in v3:
- None
Changes in v2:
- None
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Populate the PHY ops with the downstream driver as reference.
There are a couple of TODOs which need to be resolved:
- The PHY timings are all hardcoded for now. This needs to be replaced
with automatic calculations once we get/understand them.
- There are some lane configuration registers which use a new
representation between physical and logical lane mappings. For now,
we've hardcoced them to follow the default mapping (i.e
logical 0 -> phy 0, logical 1 -> phy 1 etc).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add new 10nm DSI PLL/PHY files that will be used on SDM845.
Just populate empty pll/phy funcs for now. These will be filled up
later.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
