All DSI PHY/PLL drivers were referencing their VCO parent clock by a
global name, most of which don't exist or have been renamed. These
clock drivers seem to function fine without that except the 14nm driver
for sdm6xx [1].
At the same time all DTs provide a "ref" clock as per the requirements
of dsi-phy-common.yaml, but the clock is never used. This patchset puts
that clock to use without relying on a global clock name, so that all
dependencies are explicitly defined in DT (the firmware) in the end.
Note that this patch intentionally breaks older firmware (DT) that
relies on the clock to be found globally instead. The only affected
platform is msm8974 [2] for whose dsi_phy_28nm a .name="xo" fallback is
left in place to accommodate a more graceful transition period. All
other platforms had the "ref" clock added to their phy node since its
inception, or in a followup patch some time after. These patches
wrongly assumed that the "ref" clock was actively used and have hence
been listed as "Fixes:" below.
Furthermore apq8064 was providing the wrong 19.2MHz cxo instead of
27MHz pxo clock, which has been addressed in [3].
It is expected that both [2] and [3] are applied to the tree well in
advance of this patch such that any actual breakage is extremely
unlikely, but might still occur if kernel upgrades are performed without
the DT to match. After some time the fallback for msm8974 can be
removed again as well.
[1]: https://lore.kernel.org/linux-arm-msm/386db1a6-a1cd-3c7d-a88e-dc83f8a1be96@somainline.org/
[2]: https://lore.kernel.org/linux-arm-msm/20210830175739.143401-1-marijn.suijten@somainline.org/
[3]: https://lore.kernel.org/linux-arm-msm/20210829203027.276143-2-marijn.suijten@somainline.org/
Fixes: 79e51645a1 ("arm64: dts: qcom: msm8916: Set 'xo_board' as ref clock of the DSI PHY")
Fixes: 6969d1d9c6 ("ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY")
Fixes: 0c0e72705a ("arm64: dts: sdm845: Set 'bi_tcxo' as ref clock of the DSI PHYs")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210911131922.387964-2-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Based on mesa commit daa2ccff7a0201941db3901780d179e2634057d5
Small bit of .c churn in the phy code to adapt to split up of phy
related registers.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Phy driver already knows the source PLL id basing on the set usecase and
the current PLL id. Stop passing it to the phy_enable call. As a
reminder, dsi manager will always use DSI 0 as a clock master in a slave
mode, so PLL 0 is always a clocksource for DSI 0 and it is always a
clocksource for DSI 1 too unless DSI 1 is used in the standalone mode.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-25-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The src_truthtable config is not used for some of phys, which use other
means of configuring the master/slave usecases. Inline this function
with the goal of removing src_pll_id argument in the next commit.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-24-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Drop duplicate fields pdev and id from dsi_pll_Nnm instances. Reuse
those fields from the provided msm_dsi_phy.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-22-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
All PHY drivers would map dsi_pll area. Some PHY drivers would also
map dsi_phy area again (a leftover from old PHY/PLL separation). Move
all ioremaps to the common dsi_phy driver code and drop individual
ioremapped areas from PHY drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-21-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Drop the struct msm_dsi_pll abstraction, by including vco's clk_hw
directly into struct msm_dsi_phy.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-19-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Make save_state/restore callbacks accept struct msm_dsi_phy rather than
struct msm_dsi_pll. This moves them to struct msm_dsi_phy_ops, allowing
us to drop struct msm_dsi_pll_ops.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-18-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
10nm and 7nm already do not use these helpers, as they handle setting
slave DSI clocks after enabling VCO. Modify the rest of PHY drivers to
remove unnecessary indirection and drop enable_seq/disable_seq PLL
callbacks.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-17-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Instead of setting the variable and then using it just in the one place,
determine vco_delay directly at the PLL configuration time.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-16-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use devres-enabled version of clock registration functions. This lets us
remove dsi_pll destroy callbacks completely.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-12-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
All MSM DSI PHYs provide two clocks: byte and pixel ones.
Register/unregister provided clocks from the generic place, removing
boilerplate code from all MSM DSI PHY drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-11-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
With the current upstream driver the msm_dsi_phy_type enum does not make
much sense: all DSI PHYs are probed using the dt bindings, the phy type
is not passed between drivers. Use quirks in phy individual PHY drivers
to differentiate minor harware differences and drop the enum.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-8-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Move all PLL-related callbacks into struct msm_dsi_phy_cfg. This limits
the amount of data in the struct msm_dsi_pll.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-7-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The only PLL using multiple enable sequences is the 28nm PLL, which just
does the single step in the loop. Push that support back into the PLL
code.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-6-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Each phy version is tightly coupled with the corresponding PLL code,
there is no need to keep them separate. Fuse source files together in
order to simplify DSI code.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-5-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
DSI PHY init callback would either map dsi_phy_regulator or dsi_phy_lane
depending on the PHY type. Replace those callbacks with configuration
options governing mapping those regions.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-4-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The 28nm PLL has a different iospace on MSM/APQ family B SoCs:
add a new configuration and use it when the DT reports the
"qcom,dsi-phy-28nm-hpm-fam-b" compatible.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The DSI PHY regulator supports two regulator modes: LDO and DCDC.
This mode can be selected using the "qcom,dsi-phy-regulator-ldo-mode"
device tree property.
However, at the moment only the 20nm PHY driver actually implements
that option. Add a check in the 28nm PHY driver to program the
registers correctly for LDO mode.
Tested-by: Nikita Travkin <nikitos.tr@gmail.com> # l8150
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191023165617.28738-1-stephan@gerhold.net
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DRM_DEV_INFO/ERROR/WARN instead of dev_info/err/debug to generate
drm-formatted specific log messages so that it will be easy to
differentiate in case of multiple instances of driver.
Signed-off-by: Mamta Shukla <mamtashukla555@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since DSI PHY has been a separate platform device, it should not
depend on the resources in host to be functional. This change is
to trigger PHY operations in manager, instead of host, so that
host and PHY can be completely separated.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create an init() op for dsi_phy which sets up things specific to
a given DSI PHY.
The dsi_phy driver probe expects every DSI version to get a
"dsi_phy_regulator" mmio base. This isn't the case for 8x96.
Creating an init() op will allow us to accommodate such
differences.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI host and PHY driver currently expects the DT bindings to provide
custom properties "qcom,dsi-host-index" and "qcom,dsi-phy-index" so that
the driver can identify which DSI instance it is.
The binding isn't acceptable, but the driver still needs to figure out
what its instance id. This is now done by storing the mmio starting
addresses for each DSI instance in every SoC version in the driver. The
driver then identifies the index number by trying to match the stored
address with comparing the resource start address we get from DT.
We don't have compatible strings for DSI PHY on each SoC, but only the
DSI PHY type. We only support one SoC version for each PHY type, so we
get away doing the same thing above for the PHY driver. We can revisit
this when we support two SoCs with the same DSI PHY.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The voltage changing code in this driver is broken and should be
removed. The driver sets a single, exact voltage on probe. Unless
there is a very good reason for this (which should be documented in
comments) constraints like this need to be set via the machine
constraints, voltage setting in a driver is expected to be used in cases
where the voltage varies at runtime.
In addition client drivers should almost never be calling
regulator_can_set_voltage(), if the device needs to set a voltage it
needs to set the voltage and the regulator core will handle the case
where the regulator is fixed voltage. If the driver simply skips
setting the voltage if it doesn't have permission then it should just
not bother in the first place.
Originally authored by Mark Brown <broonie@kernel.org>
Remove the min/max voltage data entries per SoC managed by the driver.
These aren't needed as we don't try to set voltages any more. Mention in
comments the voltages that each regulator expects.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current settings for 28nm PHY data lane CFG4 registers do
not work with certain panels. This change is to modify them to
hw recommended values.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change moves each PHY type specific code into
separate files.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
