Make separate function to perform raw read for one codeword and
call this function multiple times for each codeword in case of
raw page read. This separate function will help in subsequent
patches related with erased codeword bitflip detection.
It will decrease throughput for raw page read. Raw page read
is used for debug purpose so it won't affect normal flash
operations.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently there is no error checking for raw read. For raw
reads, there won’t be any ECC failure but the operational
failures are possible, so schedule the NAND_FLASH_STATUS read
after each codeword.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix value returned by ->read_page_raw() to be the
actual operation status, instead of always 0.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
QCOM NAND controller layout protects available OOB data bytes with
ECC also so when ecc->write_oob() is being called then it
can't update just OOB bytes. Currently, it first reads the last
codeword which includes old OOB bytes. Then it updates the old OOB
bytes with new ones and then again writes the codeword back.
The reading codeword is unnecessary since user is responsible to
have these bytes cleared to 0xFF.
This patch removes the read part and updates the OOB bytes with
data area padded with OxFF.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
read_page and read_oob both calls the read_page_ecc function.
The QCOM NAND controller protect the OOB available bytes with
ECC so read errors should be checked for read_oob also.
This patch moves the error checking code inside read_page_ecc
so caller does not have to check explicitly for read errors.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
parse_read_errors can be called with only oob_buf in which case
data_buf will be NULL. If data_buf is NULL, then don’t
treat this page as completely erased in case of ECC uncorrectable
error for RS ECC. For BCH ECC, the controller itself tells
regarding erased page in status register.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Following is the flow in the HW if controller tries to read erased
page:
1. First ECC uncorrectable error will be generated from ECC engine
since ECC engine first calculates the ECC with all 0xff and match
the calculated ECC with ECC code in OOB (which is again all 0xff).
2. After getting ECC error, erased CW detection logic will be
applied which is different for BCH and RS ECC
a. For BCH, HW checks if all the bytes in page are 0xff and then
it updates the status in separate register
NAND_ERASED_CW_DETECT_STATUS.
b. For RS ECC, the HW reports the same error when reading an
erased CW, but it notifies that it is an erased CW by
placing special characters at certain offsets in the
buffer.
So the erased CW detect status should be checked only if ECC engine
generated the uncorrectable error.
Currently for all other operational errors also (like TIMEOUT, MPU
errors, etc.), the erased CW detect logic is being applied so fix this
and return EIO for other operational errors.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The BAM has 3 channels - tx, rx and command. command channel
is used for register read/writes, tx channel for data writes
and rx channel for data reads. Currently, the driver assumes the
transfer completion once it gets all the command descriptors
completed. Sometimes, there is race condition between data channel
(tx/rx) and command channel completion. In these cases,
the data present in buffer is not valid during small window
between command descriptor completion and data descriptor
completion.
This patch generates NAND transfer completion when both
(Data and Command) DMA channels have completed all its DMA
descriptors. It assigns completion callback in last
DMA descriptors of that channel and wait for completion.
Fixes: 8d6b6d7e13 ("mtd: nand: qcom: support for command descriptor formation")
Cc: stable@vger.kernel.org
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently the driver uses the ECC strength specified in DT.
The QPIC/EBI2 NAND supports 4 or 8-bit ECC correction. The same
kind of board can have different NAND parts so use the ECC
strength from device parameters if it is not specified in DT.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
QCOM NAND controller supports only one step size (512) so
nand-ecc-step-size DT property is redundant. This property
can be removed and ecc step size can be assigned with 512 value.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SET/GET FEATURES are flagged ONFI-compliant because of their name. This
is not accurate as non-ONFI NAND chips support it and use it.
Rename the hooks and helpers to remove the "onfi" prefix.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
As part of the process of sharing more code between different NAND
based devices, we need to move all raw NAND related code to the raw/
subdirectory.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
