The .c files in the Makefile are ordered alphabetically. This patch
groups the function prototypes by their corresponding .c file and
brings the into the same order.
Link: https://lore.kernel.org/all/20220105154300.1258636-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A RX overflow usually happens during high system load. Printing
overflow messages to the kernel log, which on embedded systems often
is outputted on the serial console, even increases the system load.
To decrease the system load in these situations, denote the messages
to debug level and wrap them with net_ratelimit().
Link: https://lore.kernel.org/all/20220105154300.1258636-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With patch
| dd8088d5a8 PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter
the usual pm_runtime_get_sync() and pm_runtime_put_noidle()
in-case-of-error dance is no longer needed. Convert the mcp251xfd
driver to use this function.
Link: https://lore.kernel.org/all/20220105154300.1258636-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch exchanges the order of open_candev() and
pm_runtime_get_sync(), so that open_candev() is called first.
A usual reason why open_candev() fails is missing CAN bit rate
configuration. It makes no sense to resume the device from PM sleep
first just to put it to sleep if the bit rate is not configured.
Link: https://lore.kernel.org/all/20220105154300.1258636-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::tx_bytes should not be increased when
sending RTR frames.
The function can_get_echo_skb() already returns the correct length,
even for RTR frames (c.f. [1]). However, for historical reasons, the
drivers do not use can_get_echo_skb()'s return value and instead, most
of them store a temporary length (or dlc) in some local structure or
array. Using the return value of can_get_echo_skb() solves the
issue. After doing this, such length/dlc fields become unused and so
this patch does the adequate cleaning when needed.
This patch fixes all the CAN drivers.
Finally, can_get_echo_skb() is decorated with the __must_check
attribute in order to force future drivers to correctly use its return
value (else the compiler would emit a warning).
[1] commit ed3320cec2 ("can: dev: __can_get_echo_skb():
fix real payload length return value for RTR frames")
Link: https://lore.kernel.org/all/20211207121531.42941-6-mailhol.vincent@wanadoo.fr
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
[mkl: add conversion for grcan]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::rx_bytes should not be increased for the
RTR frames.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-5-mailhol.vincent@wanadoo.fr
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
For this reason, it is incorrect to copy the payload of RTR frames
(the payload buffer would only contain garbage data). This patch
encapsulates the payload copy in a check toward the RTR flag.
Link: https://lore.kernel.org/all/20211207121531.42941-4-mailhol.vincent@wanadoo.fr
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
GPIO library does copy the of_node from the parent device of the GPIO
chip, there is no need to repeat this in the individual drivers.
Remove assignment here.
For the details one may look into the of_gpio_dev_init()
implementation.
Link: https://lore.kernel.org/all/20211202205855.76946-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When deferred the reason is saved for further debugging. Besides that,
it's fine to call dev_err_probe() in ->probe() when error code is
known. Convert the driver to use dev_err_probe().
Link: https://lore.kernel.org/all/20211206165542.69887-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In some configurations, mainly ACPI-based, the clock frequency of the
device is supplied by very well established 'clock-frequency'
property. Hence, try to get it from the property at last if no other
providers are available.
Link: https://lore.kernel.org/all/20211206165542.69887-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It's not clear what was the intention of redundant usage of IS_ERR()
around the clock pointer since with the error check of devm_clk_get()
followed by bailout it can't be invalid,
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). It will allow to switch to device properties
approach in the future.
Link: https://lore.kernel.org/all/20211206165542.69887-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the error handling for mcp251xfd_chip_rx_int_enable().
Instead just returning the error, properly shut down the chip.
Link: https://lore.kernel.org/all/20211106201526.44292-2-mkl@pengutronix.de
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function can_rx_offload_threaded_irq_finish() is needed to trigger
the NAPI thread to deliver read CAN frames to the networking stack.
This patch adds the missing call to can_rx_offload_threaded_irq_finish()
in case of a bus off, before leaving the interrupt handler to avoid
packet starvation.
Link: https://lore.kernel.org/all/20211106201526.44292-1-mkl@pengutronix.de
Fixes: 30bfec4fec ("can: rx-offload: can_rx_offload_threaded_irq_finish(): add new function to be called from threaded interrupt")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With the patch 07ff4aed01 ("time/timecounter: Mark 1st argument of
timecounter_cyc2time() as const") some instances of the struct
mcp251xfd_priv can be marked as const. This patch marks these as
const.
Link: https://lore.kernel.org/r/20210813091027.159379-1-mkl@pengutronix.de
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hi3110_cmd() is supposed to return zero on success and negative
error codes on failure, but it was accidentally declared as a u8 when
it needs to be an int type.
Fixes: 57e83fb9b7 ("can: hi311x: Add Holt HI-311x CAN driver")
Link: https://lore.kernel.org/r/20210729141246.GA1267@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In some configurations, mainly ACPI-based, the clock frequency of the
device is supplied by very well established 'clock-frequency'
property. Hence, try to get it from the property at last if no other
providers are available.
Link: https://lore.kernel.org/r/20210531084444.1785397-1-mkl@pengutronix.de
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After reading all CAN frames from the controller in the IRQ handler
and storing them into a skb_queue, the driver calls napi_schedule().
In the napi poll function the skb from the skb_queue are then pushed
into the networking stack.
However if napi_schedule() is called from a threaded IRQ handler this
triggers the following error:
| NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
To avoid this, create a new rx-offload
function (can_rx_offload_threaded_irq_finish()) with a call to
local_bh_disable()/local_bh_enable() around the napi_schedule() call.
Convert all drivers that call can_rx_offload_irq_finish() from
threaded IRQ context to can_rx_offload_threaded_irq_finish().
Link: https://lore.kernel.org/r/20210724204745.736053-4-mkl@pengutronix.de
Suggested-by: Daniel Glöckner <dg@emlix.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Adding a skb to the skb_queue in rx-offload requires to take a lock.
This commit avoids this by adding an unlocked skb queue that is
appended at the end of the ISR. Having one lock at the end of the ISR
should be OK as the HW is empty, not about to overflow.
Link: https://lore.kernel.org/r/20210724204745.736053-2-mkl@pengutronix.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Co-developed-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case an error occurred in the IRQ handler, the chip status is
dumped via devcoredump and all IRQs are disabled, but the chip stays
powered for further analysis.
The chip is in an undefined state and will not receive any CAN frames,
so shut down the timestamping worker, which reads the TBC register
regularly, too. This avoids any CRC read error messages if there is a
communication problem with the chip.
Fixes: efd8d98dfb ("can: mcp251xfd: add HW timestamp infrastructure")
Link: https://lore.kernel.org/r/20210724155131.471303-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the following clang warning, by marking the functions
as maybe unused. gcc doesn't complain about unused inline functions.
| drivers/net/can/spi/mcp251xfd/mcp251xfd-core.c:564:1: warning: unused function 'mcp251xfd_chip_set_mode_nowait' [-Wunused-function]
| mcp251xfd_chip_set_mode_nowait(const struct mcp251xfd_priv *priv,
| ^
| 1 warning generated.
Link: https://lore.kernel.org/r/20210514153741.1958041-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch silences the following clang warning:
| drivers/net/can/spi/mcp251x.c:1333:17: warning: cast to smaller integer type
| 'enum mcp251x_model' from 'const void *' [-Wvoid-pointer-to-enum-cast]
| priv->model = (enum mcp251x_model)match;
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 8de29a5c34 ("can: mcp251x: Make use of device property API")
Link: https://lore.kernel.org/r/20210504200520.1179635-2-mkl@pengutronix.de
Reported-by: kernel test robot <lkp@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since 8ce8c0abcb the driver queues work via priv->restart_work when
resuming after suspend, even when the interface was not previously
enabled. This causes a null dereference error as the workqueue is only
allocated and initialized in mcp251x_open().
To fix this we move the workqueue init to mcp251x_can_probe() as there
is no reason to do it later and repeat it whenever mcp251x_open() is
called.
Fixes: 8ce8c0abcb ("can: mcp251x: only reset hardware as required")
Link: https://lore.kernel.org/r/17d5d714-b468-482f-f37a-482e3d6df84e@kontron.de
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[mkl: fix error handling in mcp251x_stop()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When we converted this code to use dev_err_probe() we accidentally
removed a return. It means that if devm_clk_get() it will lead to an
Oops when we call clk_get_rate() on the next line.
Fixes: cf8ee6de25 ("can: mcp251xfd: mcp251xfd_probe(): use dev_err_probe() to simplify error handling")
Link: https://lore.kernel.org/r/YJANZf13Qxd5Mhr1@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MCP251XFD_REG_TBC is the time base counter register. It increments
once per SYS clock tick, which is 20 or 40 MHz. Observation shows that
if the lowest byte (which is transferred first on the SPI bus) of that
register is 0x00 or 0x80 the calculated CRC doesn't always match the
transferred one.
To reproduce this problem let the driver read the TBC register in a
high frequency. This can be done by attaching only the mcp251xfd CAN
controller to a valid terminated CAN bus and send a single CAN frame.
As there are no other CAN controller on the bus, the sent CAN frame is
not ACKed and the mcp251xfd repeats it. If user space enables the bus
error reporting, each of the NACK errors is reported with a time
stamp (which is read from the TBC register) to user space.
$ ip link set can0 down
$ ip link set can0 up type can bitrate 500000 berr-reporting on
$ cansend can0 4FF#ff.01.00.00.00.00.00.00
This leads to several error messages per second:
| mcp251xfd spi0.0 can0: CRC read error at address 0x0010 (length=4, data=00 3a 86 da, CRC=0x7753) retrying.
| mcp251xfd spi0.0 can0: CRC read error at address 0x0010 (length=4, data=80 01 b4 da, CRC=0x5830) retrying.
| mcp251xfd spi0.0 can0: CRC read error at address 0x0010 (length=4, data=00 e9 23 db, CRC=0xa723) retrying.
| mcp251xfd spi0.0 can0: CRC read error at address 0x0010 (length=4, data=00 8a 30 db, CRC=0x4a9c) retrying.
| mcp251xfd spi0.0 can0: CRC read error at address 0x0010 (length=4, data=80 f3 43 db, CRC=0x66d2) retrying.
If the highest bit in the lowest byte is flipped the transferred CRC
matches the calculated one. We assume for now the CRC calculation in
the chip works on wrong data and the transferred data is correct.
This patch implements the following workaround:
- If a CRC read error on the TBC register is detected and the lowest
byte is 0x00 or 0x80, the highest bit of the lowest byte is flipped
and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
For now we assume transferred data was OK.
Link: https://lore.kernel.org/r/20210406110617.1865592-5-mkl@pengutronix.de
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch factors out the crc check into a separate function. This is
preparation for the next patch.
Link: https://lore.kernel.org/r/20210406110617.1865592-4-mkl@pengutronix.de
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch re-adds BQL support to the driver. Support for
netdev_xmit_more() will be added in a separate patch series.
Link: https://lore.kernel.org/r/20210406110617.1865592-3-mkl@pengutronix.de
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some SPI host controllers do not support full-duplex SPI transfers.
The function mcp251x_spi_trans() does a full duplex transfer. It is
used in several places in the driver, where a TX half duplex transfer
is sufficient.
To fix support for half duplex SPI host controllers, this patch
introduces a new function mcp251x_spi_write() and changes all callers
that do a TX half duplex transfer to use mcp251x_spi_write().
Fixes: e0e25001d0 ("can: mcp251x: add support for half duplex controllers")
Link: https://lore.kernel.org/r/20210330100246.1074375-1-mkl@pengutronix.de
Cc: Tim Harvey <tharvey@gateworks.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Reported-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch uses the previously added mcp251xfd_skb_set_timestamp()
function to convert the timestamp done by the CAN controller into a
proper skb hw timestamp.
Link: https://lore.kernel.org/r/20210304161209.2754463-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch add the HW timestamping infrastructure. The mcp251xfd has a
free running timer of 32 bit width, running at max 40MHz, which wraps
around every 107 seconds. The current timestamp is latched into RX and
TEF objects automatically be the CAN controller.
This patch sets up a cyclecounter, timecounter and delayed worker
infrastructure (which runs every 45 seconds) to convert the timer into
a proper 64 bit based ns timestamp.
Link: https://lore.kernel.org/r/20210304160328.2752293-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the patches:
| 1f652bb6ba can: mcp25xxfd: rx-path: reduce number of SPI core requests to set UINC bit
| 68c0c1c7f9 can: mcp251xfd: tef-path: reduce number of SPI core requests to set UINC bit
the setting of the UINC bit in the TEF and RX FIFO was batched into a
single SPI message consisting of several transfers. All transfers but
the last need to have the cs_change set to 1.
In the original patches the array of prepared transfers is send from
the beginning with the length depending on the number of read TEF/RX
objects. The cs_change of the last transfer is temporarily set to
0 during send.
This patch removes the modification of cs_change by preparing the last
transfer with cs_change to 0 and all other to 1. When sending the SPI
message the driver now starts with an offset into the array, so that
it always ends on the last entry in the array, which has the cs_change
set to 0.
Link: https://lore.kernel.org/r/20210304160328.2752293-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For easier debugging this patch adds dev coredump support to the
driver. A dev coredump is generated in case the chip fails to start or
an error in the interrupt handler is detected.
The dev coredump consists of all chip registers and chip memory, as
well as the driver's internal state of the TEF-, RX- and TX-FIFOs, it
can be analyzed with the mcp251xfd-dump tool of the can-utils:
https://github.com/linux-can/can-utils/tree/master/mcp251xfd
Link: https://lore.kernel.org/r/20210304160328.2752293-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to implement byte queue limits (bql) in CAN drivers, the
length of the CAN frame needs to be passed into the networking stack
even if the transmission failed for some reason.
To avoid to calculate this length twice, extend can_free_echo_skb() to
return that value. Convert all users of this function, too.
This patch is the natural extension of commit:
| 9420e1d495 ("can: dev: can_get_echo_skb(): extend to return can
| frame length")
Link: https://lore.kernel.org/r/20210319142700.305648-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
