Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of PHY type error occurs, the message was too generic.
Add additional info to PHY type error indicating that it can be
wrong cable connected.
Fixes: 124ed15bf1 ("i40e: Add dual speed module support")
Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make warning meaningful for the user.
Previously the trace:
"Starting FW LLDP agent failed: error: I40E_ERR_ADMIN_QUEUE_ERROR, I40E_AQ_RC_EAGAIN"
was produced when user tried to start Firmware LLDP agent,
just after it was stopped with sequence:
ethtool --set-priv-flags <dev> disable-fw-lldp on
ethtool --set-priv-flags <dev> disable-fw-lldp off
(without any delay between the commands)
At that point the firmware is still processing stop command, the behavior
is expected.
Fixes: c1041d0704 ("i40e: Missing response checks in driver when starting/stopping FW LLDP")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Disabling autonegotiation was allowed only for 10GBaseT PHY.
The condition was changed to check if link media type is BaseT.
Fixes: 3ce12ee9d8 ("i40e: Fix order of checks when enabling/disabling autoneg in ethtool")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Karen Sornek <karen.sornek@intel.com>
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove filters from being setup in case of software DCB and allow the
LLDP frames to be properly transmitted to the wire.
It is not possible to transmit the LLDP frame out of the port, if they
are filtered by control VSI. This prohibits software LLDP agent
properly communicate its DCB capabilities to the neighbors.
Fixes: 4b208eaa80 ("i40e: Add init and default config of software based DCB")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Unlike other supported adapters, 2.5G and 5G use different
PHY type identifiers for reading/writing PHY settings
and for reading link status. This commit introduces
separate PHY identifiers for these two operation types.
Fixes: 2e45d3f467 ("i40e: Add support for X710 B/P & SFP+ cards")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When FEC mode was changed the link didn't know it because
the link was not reset and new parameters were not negotiated.
Set a flag 'I40E_AQ_PHY_ENABLE_ATOMIC_LINK' in 'abilities'
to restart the link and make it run with the new settings.
Fixes: 1d96340196 ("i40e: Add support FEC configuration for Fortville 25G")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change parameters order in aq_get_phy_register() due to wrong
statistics in PHY reported by ethtool. Previously all PHY statistics were
exactly the same for all interfaces
Now statistics are reported correctly - different for different interfaces
Fixes: 0514db37dd ("i40e: Extend PHY access with page change flag")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If veb-stats was enabled, the ethtool stats triggered a warning
due to invalid size: 'unexpected stat size for veb.tc_%u_tx_packets'.
This was due to an incorrect structure definition for the statistics.
Structures and functions have been improved in line with requirements
for the presentation of statistics, in particular for the functions:
'i40e_add_ethtool_stats' and 'i40e_add_stat_strings'.
Fixes: 1510ae0be2 ("i40e: convert VEB TC stats to use an i40e_stats array")
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add Asym_Pause to supported link modes (it is supported by HW).
Lack of Asym_Pause in supported modes can cause several problems,
i.e. it won't be possible to turn the autonegotiation on
with asymmetric pause settings (i.e. Tx on, Rx off).
Fixes: 4e91bcd5d4 ("i40e: Finish implementation of ethtool get settings")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
A bunch of header comments were showing warnings when compiling
with W=1. Fix them all at once. This changes only comments.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update the Intel drivers to make use of ethtool_sprintf. The general idea
is to reduce code size and overhead by replacing the repeated pattern of
string printf statements and ETH_STRING_LEN counter increments.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-02-19
This series contains updates to i40e driver only.
Slawomir resolves an issue with the IPv6 extension headers being
processed incorrectly.
Keita Suzuki fixes a memory leak on probe failure.
Mateusz initializes AQ command structures to zero to comply with
spec, fixes FW flow control settings being overwritten and resolves an
issue with adding VLAN filters after enabling FW LLDP. He also adds
an additional check when adding TC filter as the current check doesn't
properly distinguish between IPv4 and IPv6.
Sylwester removes setting disabled bit when syncing filters as this
prevents VFs from completing setup.
Norbert cleans up sparse warnings.
v2:
- Fix fixes tag on patch 7
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Fix endianness conversions
i40e: Fix add TC filter for IPv6
i40e: Fix VFs not created
i40e: Fix addition of RX filters after enabling FW LLDP agent
i40e: Fix overwriting flow control settings during driver loading
i40e: Add zero-initialization of AQ command structures
i40e: Fix memory leak in i40e_probe
i40e: Fix flow for IPv6 next header (extension header)
====================
Link: https://lore.kernel.org/r/20210219213606.2567536-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix addition of VLAN filter for PF after enabling FW LLDP agent.
Changing LLDP Agent causes FW to re-initialize per NVM settings.
Remove default PF filter and move "Enable/Disable" to currently used
reset flag.
Without this patch PF would try to add MAC VLAN filter with default
switch filter present. This causes AQ error and sets promiscuous mode
on.
Fixes: c65e78f87f ("i40e: Further implementation of LLDP")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It seems that the right argument to be passed is &tcp_ip6_spec->ip6dst,
not &tcp_ip6_spec->ip6src, when calling function ipv6_addr_any().
Addresses-Coverity-ID: 1501734 ("Copy-paste error")
Fixes: efca91e89b ("i40e: Add flow director support for IPv6")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow user to specify VLAN field and add it to flow director. Show VLAN
field in "ethtool -n ethx" command.
Handle VLAN type and tag field provided by ethtool command. Refactored
filter addition, by replacing static arrays with runtime dummy packet
creation, which allows specifying VLAN field.
Previously, VLAN field was omitted.
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Flow director for IPv6 is not supported.
1) Implementation of support for IPv6 flow director.
2) Added handlers for addition of TCP6, UDP6, SCTP6, IPv6.
3) Refactored legacy code to make it more generic.
4) Added packet templates for TCP6, UDP6, SCTP6, IPv6.
5) Added handling of IPv6 source and destination address for flow director.
6) Improved argument passing for source and destination portin TCP6, UDP6
and SCTP6.
7) Added handling of ethtool -n for IPv6, TCP6,UDP6, SCTP6.
8) Used correct bit flag regarding FLEXOFF field of flow director data
descriptor.
Without this patch, there would be no support for flow director on IPv6,
TCP6, UDP6, SCTP6.
Tested based on x710 datasheet by using:
ethtool -N enp133s0f0 flow-type tcp4 src-port 13 dst-port 37 user-def 0x44142 action 1
ethtool -N enp133s0f0 flow-type tcp6 src-port 13 dst-port 40 user-def 0x44142 action 2
ethtool -N enp133s0f0 flow-type udp4 src-port 20 dst-port 40 user-def 0x44142 action 3
ethtool -N enp133s0f0 flow-type udp6 src-port 25 dst-port 40 user-def 0x44142 action 4
ethtool -N enp133s0f0 flow-type sctp4 src-port 55 dst-port 65 user-def 0x44142 action 5
ethtool -N enp133s0f0 flow-type sctp6 src-port 60 dst-port 40 user-def 0x44142 action 6
ethtool -N enp133s0f0 flow-type ip4 src-ip 1.1.1.1 dst-ip 1.1.1.4 user-def 0x44142 action 7
ethtool -N enp133s0f0 flow-type ip6 src-ip fe80::3efd:feff:fe6f:bbbb dst-ip fe80::3efd:feff:fe6f:aaaa user-def 0x44142 action 8
Then send traffic from client which matches the criteria provided to ethtool.
Observe that packets are redirected to user set queues with ethtool -S <interface>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement Energy Efficient Ethernet (EEE) status getting & setting.
The i40e_get_eee() requesting PHY EEE capabilities from firmware.
The i40e_set_eee() function requests PHY EEE capabilities
from firmware and sets PHY EEE advertising to full abilities or 0
depending whether EEE is to be enabled or disabled.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add extra handling on changing the "disable-fw-lldp" private
flag to properly initialize software based DCB feature.
Add default configuration of DCB functionality when Firmware
LLDP agent is turned off, in case of driver probe and device
reset on reconfiguration.
Update copyright dates as appropriate.
Software based DCB is a brand-new feature in i40e driver.
Before, DCB was implemented by Firmware LLDP agent only. The agent was
responsible for handling incoming DCB-related LLDP frames and
applying received DCB configuration to hardware.
Default configuration and new initialization flow for software based
DCB is required. If LLDP agent is turned off in BIOS, or after
setting private flag ("disable-fw-lldp on"). The driver initializes
DCB functionality with default values, one traffic class with 100%
bandwidth allocated.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Starting with API version 1.10 firmware for X722 devices has ability
to change FEC settings in PHY. Code added in this patch allows
changing FEC settings if the capability flag indicates the device
supports this feature.
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the explicit umem reference passed to the driver in AF_XDP
zero-copy mode with the buffer pool instead. This in preparation for
extending the functionality of the zero-copy mode so that umems can be
shared between queues on the same netdev and also between netdevs. In
this commit, only an umem reference has been added to the buffer pool
struct. But later commits will add other entities to it. These are
going to be entities that are different between different queue ids
and netdevs even though the umem is shared between them.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-2-git-send-email-magnus.karlsson@intel.com
After OS requests to down a link on a physical network port, the
traffic is no longer being processed but the physical link with
a link partner is still established.
Currently there is a feature (Link down on close) which allows
to physically bring the link down (after OS request).
With this patch new feature with similar capability is introduced:
TOTAL_PORT_SHUTDOWN
Allows to physically disable the link on the NIC's port.
If enabled, (after link down request from the OS)
no link, traffic or led activity is possible on that port.
If I40E_FLAG_TOTAL_PORT_SHUTDOWN is enabled, the
I40E_FLAG_LINK_DOWN_ON_CLOSE_ENABLED must be explicitly forced to
true and cannot be disabled at that time.
The functionalities are exclusive in terms of configuration, but
they also have similar behavior (allowing to disable physical link
of the port), with following differences:
- LINK_DOWN_ON_CLOSE_ENABLED is configurable at host OS run-time
and is supported by whole family of 7xx Intel Ethernet Controllers
- TOTAL_PORT_SHUTDOWN may be enabled only before OS loads (in BIOS)
only if motherboard's BIOS and NIC's FW has support of it
- when LINK_DOWN_ON_CLOSE_ENABLED is used, the link is being brought
down by sending phy_type=0 to NIC's FW
- when TOTAL_PORT_SHUTDOWN is used, phy_type is not altered, instead
the link is being brought down by clearing bit
(I40E_AQ_PHY_ENABLE_LINK) in abilities field of
i40e_aq_set_phy_config structure
Introduced changes:
- new private flag I40E_FLAG_TOTAL_PORT_SHUTDOWN for handling the
feature
- probe of NVM if the feature was enabled at driver's port
initialization
- special handling on link-down procedure to let FW physically
shutdown the port if the feature was enabled
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Convert all the remaining 'fall through" code comments to the newer
'fallthrough;' keyword.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2020-06-25
This series contains updates to i40e driver and removes the individual
driver versions from all of the Intel wired LAN drivers.
Shiraz moves the client header so that it can easily be shared between
the i40e LAN driver and i40iw RDMA driver.
Jesse cleans up the unused defines, since they are just dead weight.
Alek reduces the unreasonably long wait time for a PF reset after reboot
by using jiffies to limit the maximum wait time for the PF reset to
succeed. Added additional logging to let the user know when the driver
transitions into recovery mode. Adds new device support for our 5 Gbps
NICs.
Todd adds a check to see if MFS is set after warm reboot and notifies
the user when MFS is set to anything lower than the default value.
Arkadiusz fixes a possible race condition, where were holding a
spin-lock while in atomic context.
v2: removed code comments that were no longer applicable in patch 2 of
the series. Also removed 'inline' from patch 4 and patch 8 of the
series. Also re-arranged code to be able to remove the forward
function declarations. Dropped patch 9 of the series, while the
author works on cleaning up the commit message.
v3: Updated patch 8 description to answer Jakub's questions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.
For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.
What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
When the AF_XDP buffer allocator was introduced, the Rx SW ring
"rx_bi" allocation was moved from i40e_setup_rx_descriptors()
function, and was instead done in the i40e_configure_rx_ring()
function.
This broke the ethtool set_ringparam() hook for changing the Rx
descriptor count, which was relying on i40e_setup_rx_descriptors() to
handle the allocation.
Fix this by adding an explicit i40e_alloc_rx_bi() call to
i40e_set_ringparam().
Fixes: be1222b585 ("i40e: Separate kernel allocated rx_bi rings from AF_XDP rings")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
Let ethtool print driver and firmware versions when NIC is in
recovery mode. Assign i40e_get_drvinfo() operation to ethtool
recovery mode operations. Previously ethtool did not report
driver and firmware versions when NIC was in recovery mode.
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently FW use MDIO I/F number corresponded with current PF for PHY
access. This code allow to specify used MDIO I/F number.
Add new field - command flags with only one flag for now. Added flag
tells FW that it shouldn't change page while accessing QSFP module, as
it was set manually.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix display of parameters "Configured FEC encodings:" and "Advertised
FEC modes:" in ethtool. Implemented by setting proper FEC bits in
“advertising” bitmask of link_modes struct and “fec” bitmask in
ethtool_fecparam struct. Without this patch wrong FEC settings
can be shown.
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to the ixgbe issue fixed in:
655c914145 ("ixgbe: Check DDM existence in transceiver before access)
i40e has the same issue when reading eeprom from SFP's module that comply
with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM)
interface described in it. The existence of such area is specified by bit
6 of byte 92, set to 1 if implemented.
Without this patch, due to not checking this bit i40e fails to read SFP
module's eeprom with the follow message:
ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error
Because it fails to read the additional 256 bytes in which it was assumed
to exist the DDM data.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to i40e_get_ethtool_stats, add a goto to verify that the data
pointer for the strings lines up with the expected stats count. This
helps ensure that bugs are not introduced when adding stats.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Updates visual effect for advertised mode after setting desired mode.
The mode appears in advertised FEC mode correctly, when ethtool
interface command is called. Without this commit advertised FEC
is displayed regardless of the settings as "None BaseR RS".
Signed-off-by: Czeslaw Zagorski <czeslawx.zagorski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes missing call of i40e_update_veb_stats() in function
i40e_get_ethtool_stats() to update stats data of VEB and VEB TC
counters before they are written into ethtool buffer.
Before the patch ethtool counters may fell behind interface counters.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changing descriptor count via 'ethtool -G' is not persistent across resets.
When PF reset occurs, we roll back to the default value of vsi->num_desc,
which is used then in i40e_alloc_rings to set descriptor count. XDP does a
PF reset so when user has changed the descriptor count and load XDP
program, the default count will be back there.
To fix this:
* introduce new VSI members - num_tx_desc and num_rx_desc in favour of
num_desc
* set them in i40e_set_ringparam to user's values
* set them to default values in i40e_set_num_rings_in_vsi only when they
don't have previous values
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver updated pf->flags before calling i40e_aq_start_lldp().
This patch moved down updating pf->flags down so flags will be
updated only in case of successful i40e_aq_start_lldp() call.
Also was introduced is_reset_needed local flag to avoid unnecessary h/w
reset in case 40e_aq_start_lldp() didn't change lldp state.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver did not check response on LLDP flag change and always returned
SUCCESS.
This patch now checks for an error and returns an error code and has
additional information in the log.
Signed-off-by: Piotr Marczak <piotr.marczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds functions stubs to support EEE on/off.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New device ids are created to support X710 backplane and SFP+ cards.
This patch adds in i40e driver support for 2.5GbaseT and 5GbaseT speed.
It's implemented by checking I40E_CAP_PHY_TYPE_2_5GBASE_T,
I40E_CAP_PHY_TYPE_5GBASE_T bits from f/w and setting corresponding bits
in ethtool link ksettings supported and advertising masks.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the typo in I40E_CAP_PHY_TYPE mode link code.
It was fixed by changing 40000baseLR4_Full to 40000baseKR4_Full
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces "recovery mode" to the i40e driver. It is
part of a new Any2Any idea of upgrading the firmware. In this
approach, it is required for the driver to have support for
"transition firmware", that is used for migrating from structured
to flat firmware image. In this new, very basic mode, i40e driver
must be able to handle particular IOCTL calls from the NVM Update
Tool and run a small set of AQ commands.
These additional AQ commands are part of the interface used by
the NVMUpdate tool. The NVMUpdate tool contains all of the
necessary logic to reference these new AQ commands. The end user
experience remains the same, they are using the NVMUpdate tool to
update the NVM contents.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Piotr Marczak <piotr.marczak@intel.com>
Tested-by: Don Buchholz <donald.buchholz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code implements driver code changes necessary for LLDP
Agent support. Modified i40e_aq_start_lldp() and
i40e_aq_stop_lldp() adding false parameter whether LLDP state
should be persistent across power cycles.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add assignments for advertising 40GBase_LR4, 40GBase_CR4 and fibre
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Defined the advertised link mode field for 40000baseSR4_Full for
use with ethtool.
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces DDP (Dynamic Device Personalization) which allows
loading profiles that change the way internal parser interprets processed
frames. To load DDP profiles it utilizes ethtool flash feature. The files
with recipes must be located in /var/lib/firmware directory. Afterwards
the recipe can be loaded by invoking:
ethtool -f <if_name> <file_name> 100
ethtool -f <if_name> - 100
See further details of this feature in the i40e documentation, or
visit
https://www.intel.com/content/www/us/en/architecture-and-technology/ethernet/dynamic-device-personalization-brief.html
The driver shall verify DDP profile can be loaded in accordance with
the rules:
* Package with Group ID 0 are exclusive and can only be loaded the first.
* Packages with Group ID 0x01-0xFE can only be loaded simultaneously
with the packages from the same group.
* Packages with Group ID 0xFF are compatible with all other packages.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current check for WoL on i40e is broken. Code comment says only
magic packet is supported, so only check for that.
Fixes: 540a152da7 (i40e/ixgbe/igb: fail on new WoL flag setting WAKE_MAGICSECURE)
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are several statements that have incorrect levels of indentation,
fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
