Implement support for Credit-based shaper(CBS) Qdisc hardware
offload mode in the driver. There are two sets of IEEE802.1Qav
(CBS) HW logic in i225 controller and this patch supports
enabling them in the top two priority TX queues.
Driver implemented as recommended by Foxville External
Architecture Specification v0.993. Idleslope and Hi-credit are
the CBS tunable parameters for i225 NIC, programmed in TQAVCC
and TQAVHC registers respectively.
In-order for IEEE802.1Qav (CBS) algorithm to work as intended
and provide BW reservation CBS should be enabled in highest
priority queue first. If we enable CBS on any of low priority
queues, the traffic in high priority queue does not allow low
priority queue to be selected for transmission and bandwidth
reservation is not guaranteed.
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Signed-off-by: Mallikarjuna Chilakala <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This reverts commit cf8331825a.
There are better Linux interfaces to export the different LED modes
and blinking reasons.
Revert this patch for now and come up with better solution later.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20210719101640.16047-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Each i225 has three LEDs. Export them via the LED class framework.
Each LED is controllable via sysfs. Example:
$ cd /sys/class/leds/igc_led0
$ cat brightness # Current Mode
$ cat max_brightness # 15
$ echo 0 > brightness # Mode 0
$ echo 1 > brightness # Mode 1
The brightness field here reflects the different LED modes ranging
from 0 to 15.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Intel i225 NIC has the possibility to add flex filters which can
match up to the first 128 byte of a packet. These filters are useful
for all kind of packet matching. One particular use case is Profinet,
as the different traffic classes are distinguished by the frame id
range which cannot be matched by any other means.
Add code to configure and enable flex filters.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add HW VLAN acceleration protocol handling. In case of HW VLAN tagging,
we need that protocol available in the ndo_start_xmit(), so that it will be
stored in a new fields in the skb.
HW offloading is set to OFF by default.
Users are allow to turn on/off Rx/Tx HW VLAN acceleration via ethtool.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The MDICNFG register from igc registers is not used so remove it.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The i225 device offers a number of special PTP Hardware Clock features on
the Software Defined Pins (SDPs) - much like i210, which is used as
inspiration for this patch. It enables two possible functions, namely
time stamping external events and periodic output signals.
The assignment of PHC functions to the four SDP can be freely chosen by
the user.
For the external events time stamping, when the SDP (configured as input
by user) level changes, an interrupt is generated and the kernel
Precision Time Protocol (PTP) is informed.
For the periodic output signals, the i225 is configured to generate them
(so the SDP level will change periodically) and the driver also has to
keep updating the time of the next level change. However, this work is
not necessary for some frequencies as the i225 takes care of them
(namely, anything with a half-cycle of 500ms, 250ms, 125ms or < 70ms).
While i225 allows up to four timers to be used to source the time used
on the external events or output signals, this patch uses only one of
those timers. Main reason is to keep it simple, as it's not clear how
these extra timers would be exposed to users. Note that currently a NIC
can expose a single PTP device.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Extend reporting of NVM image version to include the gPHY (i225 PHY)
firmware version.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove ictxptc, ictxatc, cbtmpc, cbrdpc, cbrmpc and htcbdpc fields from
the hw_stats structure. Accordance to the i225 device
specification these fields not in use.
This patch come to clean up the driver code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
IGC_ICTXPTC and IGC_ICTXATC are already defined elsewhere, remove this
double definition. Also, remove unneeded registers as they are not
applicable to i225 devices.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tx Queue Min Threshold Count register no applicable for the i225 device.
This patch comes to clean up it.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Though we are populating and tracking ictxqec, the value is not being used
for anything so remove it altogether and save the register read.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
TCP segmentation TX context fail counter is not
applicable for i225 devices.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown<aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add EEE TX LPI and EEE RX LPI counters. A EEE TX LPI event
occurs when the transmitter enters EEE (IEEE 802.3az) LPI
state. A EEE RX LPI event occurs when the receiver detect
link partner entry into EEE(IEEE 802.3az) LPI state.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Differently from I210, I225 doesn't report Rx timestamps via the TS bit
Rx descriptor + RXSTMPL/RXSTMPH registers mechanism. Rx timestamps are
reported in the packet buffer only, which is implemented by igc_ptp_rx_
pktstamp(). So this patch removes igc_ptp_rx_rgtstamp() and all code
related to it, copied from igb driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The LTR message on the PCIe inform the requested latency
on which the PCIe must become active to the downstream
PCIe port of the system.
This patch provide recommended LTR parameters by i225
specification.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IEEE802.3az-2010 Energy Efficient Ethernet has been
approved as standard (September 2010) and the driver
can enable and disable it via ethtool.
Disable the feature by default on parts which support it.
Add enable/disable eee options.
tx-lpi, tx-timer and advertise not supported yet.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accordance to the i225 datasheet this register address
used by Host Transmit Discarded Packet by MAC counter
and not by not applicable Carrier Extension Error counter.
This patch comes to fix this wrong definition.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accordance to the i225 datasheet sequence error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Receive error counter reflect total number of non-filtered
packets received with errors. This includes: CRC error,
symbol error, Rx data error and carrier extend error.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accordance to the i225 datasheet symbol error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Per queue good transmitted packet counter not applicable for i225 device.
This patch comes to clean up this register.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Header redirection missed packet counter not applicable for i225 device.
This patch comes to clean up this register.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Part of circuit breaker registers is obsolete
and not applicable for i225 device.
This patch comes to clean up these registers.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tx data FIFO Head/Tail, Saved and Packet Count registers
not applicable for i225 LAN controller.
This patch comes to clean up these registers.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch remove the IGC_RXPBS macro defined in line 233 since it is
already defined in line 18 with the exactly same value.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch renames the IGC_VLAPQF macro to IGC_VLANPQF as well as
related macros so they match the register name and fields described in
the data sheet.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igc driver has leftovers from the previous device that supported
Virtualization. This can be found in the function IGC_REMOVED which
became obsolete, and can be removed.
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
GCR (PCIe Control) register not in use and should be removed
This patch clean up this register
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flow control status register not applicable for i225 parts
so clean up the unneeded define.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduced igc_diag.c and igc_diag.h, these files have the
diagnostics functionality of igc driver. For the time being
these files are being used by ethtool self-test callbacks.
Which mean that eeprom, registers and link self-tests for
ethtool were implemented.
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds support for translating taprio schedules into i225 cycles. This
will allow schedules to run in the hardware, making the schedules
enforcement more precise and saving CPU time.
Right now, the only simple schedules are allowed, complex schedules are
rejected. "simple" in this context are schedules that each HW queue is
opened and closed only once in each cycle.
Changing schedules is still not supported as well.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Placeholder for debugging functionality.
In this patch, we add some registers and rings summary dumps.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
PHY power management control should provide a reliable and accurate
indication of PHY reset completion and decrease the delay time
after a PHY reset
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds support for timestamping received packets.
It is based on the i210, as many features of i225 work the same way.
The main difference from i210 is that i225 has support for choosing
the timer register to use when timestamping packets. Right now, we
only support using timer 0. The other difference is that i225 stores
two timestamps in the receive descriptor, right now, we only retrieve
one.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows the creation of the /dev/ptpX device for i225, and reading
and writing the time.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add show and configure network flow classification (NFC) methods
to the ethtool. Show the specifies Rx ntuple filters.
Configures receive network flow classification option or rules.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable the multi queues to receive.
Program the direction of packets to specified queues according
to the mode selected in the MRQC register.
Multiple receive queues defined by filters and RSS for 4 queues.
Enable/disable RSS hashing and also to enable multiple receive queues.
This patch will allow further ethtool support development.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds basic ethtool support to the device to allow
for configuration.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove redundant igc_check_for_link_base code and replace it with
an igc_check_for_copper_link method.
Fix duplication of IGC_ADVTXD_PAYLEN_SHIFT mask declaration.
Remove obsolete IGC_SCVPC register definition.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add PHY's ID support
Add support for initialization, acquire and release of PHY
Enable register access
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code for NVM support and get MAC address, complete probe
method.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code for hardware initialization and reset
Add code for semaphore handling
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds the defines and structures necessary to support both Tx
and Rx descriptor rings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the basic defines and structures needed by the PF for
operation. With this it is possible to bring up the interface,
but without being able to configure any of the filters on
the interface itself.
Add skeleton for a function pointers.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
