Add new device ID for the next step of the silicon and
reflect the I226_LMVP part.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices only have copper phy media type. There is no point in
checking phy media type during the phy initialization. This patch cleans
up a pointless check.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The variable ret_val is being initialized with a value that is never
read, it is being updated later on. The assignment is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver tried to use Linux' native software I2C bus master
(i2c-algo-bits) for exporting the I2C interface that talks to the SFP
cage(s) towards userspace. As-is, however, the physical SCL/SDA pins
were not moving at all, staying at logical 1 all the time.
The main culprit was the I2CPARAMS register where igb was not setting
the I2CBB_EN bit. That meant that all the careful signal bit-banging was
actually not being propagated to the chip pads (I verified this with a
scope).
The bit-banging was not correct either, because I2C is supposed to be an
open-collector bus, and the code was driving both lines via a totem
pole. The code was also trying to do operations which did not make any
sense with the i2c-algo-bits, namely manipulating both SDA and SCL from
igb_set_i2c_data (which is only supposed to set SDA). I'm not sure if
that was meant as an optimization, or was just flat out wrong, but given
that the i2c-algo-bits is set up to work with a totally dumb GPIO-ish
implementation underneath, there's no need for this code to be smart.
The open-drain vs. totem-pole is fixed by the usual trick where the
logical zero is implemented via regular output mode and outputting a
logical 0, and the logical high is implemented via the IO pad configured
as an input (thus floating), and letting the mandatory pull-up resistors
do the rest. Anything else is actually wrong on I2C where all devices
are supposed to have open-drain connection to the bus.
The missing I2CBB_EN is set (along with a safe initial value of the
GPIOs) just before registering this software I2C bus.
The chip datasheet mentions HW-implemented I2C transactions (SFP EEPROM
reads and writes) as well, but I'm not touching these for simplicity.
Tested on a LR-Link LRES2203PF-2SFP (which is an almost-miniPCIe form
factor card, a cable, and a module with two SFP cages). There was one
casualty, an old broken SFP we had laying around, which was used to
solder some thin wires as a DIY I2C breakout. Thanks for your service.
With this patch in place, I can `i2cdump -y 3 0x51 c` and read back data
which make sense. Yay.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
See-also: https://www.spinics.net/lists/netdev/msg490554.html
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the following coccicheck warning:
./drivers/net/ethernet/intel/i40e/i40e_xsk.c:229:35-40: WARNING:
conversion to bool not needed here
./drivers/net/ethernet/intel/ice/ice_xsk.c:399:35-40: WARNING:
conversion to bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-10-28
This series contains updates to ice driver only.
Michal adds support for eswitch drop and redirect filters from and to
tunnel devices. From meaning from uplink to VF and to means from VF to
uplink. This is accomplished by adding support for indirect TC tunnel
notifications and adding appropriate training packets and match fields
for UDP tunnel headers. He also adds returning virtchannel responses for
blocked operations as returning a response is still needed.
Marcin sets netdev min and max MTU values on port representors to allow
for MTU changes over default values.
Brett adds detecting and reporting of PHY firmware load issues for devices
which support this.
Nathan Chancellor fixes a clang warning for implicit fallthrough.
Wang Hai fixes a return value for failed allocation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Return error code if devm_kmemdup() fails in ice_get_recp_frm_fw()
Fixes: fd2a6b71e3 ("ice: create advanced switch recipe")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Clang warns:
drivers/net/ethernet/intel/ice/ice_lib.c:1906:2: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
default:
^
drivers/net/ethernet/intel/ice/ice_lib.c:1906:2: note: insert 'break;' to avoid fall-through
default:
^
break;
1 error generated.
Clang is a little more pedantic than GCC, which does not warn when
falling through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst, which
states that all switch/case blocks must end in either break,
fallthrough, continue, goto, or return. Add the missing break to silence
the warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/1482
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some devices have support for loading the PHY FW and in some cases this
can fail. When this fails, the FW will set the corresponding bit in the
link info structure. Also, the FW will send a link event if the correct
link event mask bit is set. Add support for printing an error message
when the PHY FW load fails during any link configuration flow and the
link event flow.
Since ice_check_module_power() is already doing something very similar
add a new function ice_check_link_cfg_err() so any failures reported in
the link info's link_cfg_err member can be printed in this one function.
Also, add the new ICE_FLAG_PHY_FW_LOAD_FAILED bit to the PF's flags so
we don't constantly print this error message during link polling if the
value never changed.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This change adds support for changing MTU on port representor in
switchdev mode, by setting the min/max MTU values on port representor
netdev. Before it was possible to change the MTU only in a limited,
default range (68-1500).
Signed-off-by: Marcin Szycik <marcin.szycik@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Part of virtchannel messages are treated in different way in switchdev
mode to block configuring VFs from iavf driver side. This blocking was
done by doing nothing and returning success, event without sending
response.
Not sending response for opcodes that aren't supported in switchdev mode
leads to block iavf driver message handling. This happens for example
when vlan is configured at VF config time (VLAN module is already
loaded).
To get rid of it ice driver should answer for each VF message. In
switchdev mode:
- for adding/deleting VLAN driver should answer success without doing
anything to allow creating vlan device on VFs
- for enabling/disabling VLAN stripping and promiscuous mode driver
should answer not supported, this feature in switchdev can be only
set from host side
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mostly reuse code from Geneve and VXLAN in TC parsing code. Add new GRE
header to match on correct fields. Create new dummy packets with GRE
fields.
Instead of checking if any encap values are presented in TC flower,
check if device is tunnel type or redirect is to tunnel device. This
will allow adding all combination of rules. For example filters only
with inner fields.
Return error in case device isn't tunnel but encap values are presented.
gre example:
- create tunnel device
ip l add $NVGRE_DEV type gretap remote $NVGRE_REM_IP local $VF1_IP \
dev $PF
- add tc filter (in switchdev mode)
tc filter add dev $NVGRE_DEV protocol ip parent ffff: flower dst_ip \
$NVGRE1_IP action mirred egress redirect dev $VF1_PR
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add definition of UDP tunnel dummy packets. Fill destination port value
in filter based on UDP tunnel port. Append tunnel flags to switch filter
definition in case of matching the tunnel.
Both VXLAN and Geneve are UDP tunnels, so only one new header is needed.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add definition for VXLAN and Geneve dummy packet. Define VXLAN and
Geneve type of fields to match on correct UDP tunnel header.
Parse tunnel specific fields from TC tool like outer MACs, outer IPs,
outer destination port and VNI. Save values and masks in outer header
struct and move header pointer to inner to simplify parsing inner
values.
There are two cases for redirect action:
- from uplink to VF - TC filter is added on tunnel device
- from VF to uplink - TC filter is added on PR, for this case check if
redirect device is tunnel device
VXLAN example:
- create tunnel device
ip l add $VXLAN_DEV type vxlan id $VXLAN_VNI dstport $VXLAN_PORT \
dev $PF
- add TC filter (in switchdev mode)
tc filter add dev $VXLAN_DEV protocol ip parent ffff: flower \
enc_dst_ip $VF1_IP enc_key_id $VXLAN_VNI action mirred egress \
redirect dev $VF1_PR
Geneve example:
- create tunnel device
ip l add $GENEVE_DEV type geneve id $GENEVE_VNI dstport $GENEVE_PORT \
remote $GENEVE_IP
- add TC filter (in switchdev mode)
tc filter add dev $GENEVE_DEV protocol ip parent ffff: flower \
enc_key_id $GENEVE_VNI dst_ip $GENEVE1_IP action mirred egress \
redirect dev $VF1_PR
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement indirect notification mechanism to support offloading TC rules
on tunnel devices.
Keep indirect block list in netdev priv. Notification will call setting
tc cls flower function. For now we can offload only ingress type. Return
not supported for other flow block binder.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
PTP is currently only supported on E810 devices, it is checked
in ice_ptp_init(). However, there is no check in ice_ptp_release().
For other E800 series devices, ice_ptp_release() will be wrongly executed.
Fix the following calltrace.
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
Workqueue: ice ice_service_task [ice]
Call Trace:
dump_stack_lvl+0x5b/0x82
dump_stack+0x10/0x12
register_lock_class+0x495/0x4a0
? find_held_lock+0x3c/0xb0
__lock_acquire+0x71/0x1830
lock_acquire+0x1e6/0x330
? ice_ptp_release+0x3c/0x1e0 [ice]
? _raw_spin_lock+0x19/0x70
? ice_ptp_release+0x3c/0x1e0 [ice]
_raw_spin_lock+0x38/0x70
? ice_ptp_release+0x3c/0x1e0 [ice]
ice_ptp_release+0x3c/0x1e0 [ice]
ice_prepare_for_reset+0xcb/0xe0 [ice]
ice_do_reset+0x38/0x110 [ice]
ice_service_task+0x138/0xf10 [ice]
? __this_cpu_preempt_check+0x13/0x20
process_one_work+0x26a/0x650
worker_thread+0x3f/0x3b0
? __kthread_parkme+0x51/0xb0
? process_one_work+0x650/0x650
kthread+0x161/0x190
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
Fixes: 4dd0d5c33c ("ice: add lock around Tx timestamp tracker flush")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the PF is a member of a link aggregate, and the driver
is removed, the process will hang unless we respond to the
NETDEV_UNREGISTER event that is sent to the event_handler
for LAG.
Add a case statement for the ice_lag_event_handler to unlink
the PF from the link aggregate.
Also remove code that was incorrectly applying a dev_hold to
peer_netdevs that were associated with the ice driver.
Fixes: df006dd4b1 ("ice: Add initial support framework for LAG")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support to add/delete channel specific filter using tc-flower.
For now, only supported action is "skip_sw hw_tc <tc_num>"
Filter criteria is specific to channel and it can be
combination of L3, L3+L4, L2+L4.
Example:
MATCH criteria Action
---------------------------
src and/or dest IPv4[6]/mask -> Forward to "hw_tc <tc_num>"
dest IPv4[6]/mask + dest L4 port -> Forward to "hw_tc <tc_num>"
dest MAC + dest L4 port -> Forward to "hw_tc <tc_num>"
src IPv4[6]/mask + src L4 port -> Forward to "hw_tc <tc_num>"
src MAC + src L4 port -> Forward to "hw_tc <tc_num>"
Adding tc-flower filter for channel using "hw_tc"
-------------------------------------------------
tc qdisc add dev <ethX> clsact
Above two steps are only needed the first time when adding
tc-flower filter.
tc filter add dev <ethX> protocol ip ingress prio 1 flower \
dst_ip 192.168.0.1/32 ip_proto tcp dst_port 5001 \
skip_sw hw_tc 1
tc filter show dev <ethX> ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1 hw_tc 1
eth_type ipv4
ip_proto tcp
dst_ip 192.168.0.1
dst_port 5001
skip_sw
in_hw in_hw_count 1
Delete specific filter:
-------------------------
tc filter del dev <ethx> ingress pref 1 handle 0x1 flower
Delete All filters:
------------------
tc filter del dev <ethX> ingress
Co-developed-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support in driver for TC_QDISC_SETUP_MQPRIO. This support
enables instantiation of channels in HW using existing MQPRIO
infrastructure which is extended to be offloadable. This
provides a mechanism to configure dedicated set of queues for
each TC.
Configuring channels using "tc mqprio":
--------------------------------------
tc qdisc add dev <ethX> root mqprio num_tc 3 map 0 1 2 \
queues 4@0 4@4 4@8 hw 1 mode channel
Above command configures 3 TCs having 4 queues each. "hw 1 mode channel"
implies offload of channel configuration to HW. When driver processes
configuration received via "ndo_setup_tc: QDISC_SETUP_MQPRIO", each
TC maps to HW VSI with specified queues.
User can optionally specify bandwidth min and max rate limit per TC
(see example below). If shaper params like min and/or max bandwidth
rate limit are specified, driver configures VSI specific rate limiter
in HW.
Configuring channels and bandwidth shaper parameters using "tc mqprio":
----------------------------------------------------------------
tc qdisc add dev <ethX> root mqprio \
num_tc 4 map 0 1 2 3 queues 4@0 4@4 4@8 4@12 hw 1 mode channel \
shaper bw_rlimit min_rate 1Gbit 2Gbit 3Gbit 4Gbit \
max_rate 4Gbit 5Gbit 6Gbit 7Gbit
Command to view configured TCs:
-----------------------------
tc qdisc show dev <ethX>
Deleting TCs:
------------
tc qdisc del dev <ethX> root mqprio
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add infrastructure required for "ndo_setup_tc:qdisc_mqprio".
ice_vsi_setup is modified to configure traffic classes based
on mqprio data received from the stack. This includes low-level
functions to configure min, max rate-limit parameters in hardware
for traffic classes. Each traffic class gets mapped to a hardware
channel (VSI) which can be individually configured with different
bandwidth parameters.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As part of support for E810 XXV devices, some device ids were
inadvertently left out. Add those missing ids.
Fixes: 195fb97766 ("ice: add additional E810 device id")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
The device ID for I226_K was incorrectly assigned, update the device
ID to the correct one.
Fixes: bfa5e98c9d ("igc: Add new device ID")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update the HW MAC initialization flow. Do not gate DMA clock from
the modPHY block. Keeping this clock will prevent dropped packets
sent in burst mode on the Kumeran interface.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213651
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213377
Fixes: fb776f5d57 ("e1000e: Add support for Tiger Lake")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We have the same LAN controller on different PCHs. Separate TGP board
type from SPT which will allow for specific fixes to be applied for
TGP platforms.
Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Return the error code if ice_eswitch_configure() fails. Don't return
success.
Fixes: 1c54c83993 ("ice: enable/disable switchdev when managing VFs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use 2-factor multiplication argument form devm_kcalloc() instead
of devm_kzalloc().
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch improves a few things:
- it fixes issue where ethtool -i reports that PR supports
priv-flags and tests when in fact it does not support them
- instead of using the same functions for both PF and PR ethtool ops,
this patch introduces separate ops for both cases and internal
functions with core logic.
- prevent accessing VF VSI while VF is not ready by calling
ice_check_vf_ready_for_cfg
- all PR specific functions in ethtool.c were moved to one place in
file
- instead overwriting n_priv_flags in ice_repr_get_drvinfo,
priv-flags code was moved from __ice_get_drvinfo to ice_get_drvinfo
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently it is not possible to set/unset lb_en and lan_en flags
for advanced rules during their creation. Both flags are enabled
by default. In case of switchdev offloads for egress traffic we
need lb_en to be disabled. Because of that, we work around it by
updating the rule immediately after its creation.
This change allows us to set/unset those flags right away and it
gets rid of old workaround as well. Using ice_adv_rule_flags_info
structure we can pass info about flags we want to be set for
a given advanced rule. Flags are stored in flags_info.act.
Values from act would be used only if act_valid was set to true,
otherwise default values would be used.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Merge issues caused the check for switchdev mode has been inserted
in wrong place. It should be in ice_set_vf_trust not in ice_set_vf_mac.
Trusted VFs are forbidden in switchdev mode because they should
be configured only from the host side.
Fixes: 1c54c83993 ("ice: enable/disable switchdev when managing VFs")
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver tried to work around missing completion events that occurred
while interrupts are disabled, by triggering a software interrupt
whenever we exit polling (but we had to have polled at least once).
This was causing a *lot* of extra interrupts for some workloads like
NVMe over TCP, which resulted in regressions in performance. It was also
visible when polling didn't prevent interrupts when busy_poll was
enabled.
Fix the extra interrupts by utilizing our previously unused 3rd ITR
(interrupt throttle) index and set it to 20K interrupts per second, and
then trigger a software interrupt within that rate limit.
While here, slightly refactor the code to avoid an overwrite of a local
variable in the case of wb_en = true.
Fixes: b7306b42be ("ice: manage interrupts during poll exit")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If the adaptive settings are changed with
ethtool -C ethx adaptive-rx off adaptive-tx off
then the interrupt rate limit should be maintained as a user set value,
but only if BOTH adaptive settings are off. Fix a bug where the rate
limit that was being used in adaptive mode was staying set in the
register but was not reported correctly by ethtool -c ethx. Due to long
lines include a small refactor of q_vector variable.
Fixes: b8b4772377 ("ice: refactor interrupt moderation writes")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver was having trouble with unreliable latency when doing single
threaded ping-pong tests. This was root caused to the DIM algorithm
landing on a too slow interrupt value, which caused high latency, and it
was especially present when queues were being switched frequently by the
scheduler as happens on default setups today.
In attempting to improve this, we allow the upper rate limit for
interrupts to move to rate limit of 4 microseconds as a max, which means
that no vector can generate more than 250,000 interrupts per second. The
old config was up to 100,000. The driver previously tried to program the
rate limit too frequently and if the receive and transmit side were both
active on the same vector, the INTRL would be set incorrectly, and this
change fixes that issue as a side effect of the redesign.
This driver will operate from now on with a slightly changed DIM table
with more emphasis towards latency sensitivity by having more table
entries with lower latency than with high latency (high being >= 64
microseconds).
The driver also resets the DIM algorithm state with a new stats set when
there is no work done and the data becomes stale (older than 1 second),
for the respective receive or transmit portion of the interrupt.
Add a new helper for setting rate limit, which will be used more
in a followup patch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement ndo_set_vf_rate to support setting of min_tx_rate and
max_tx_rate; set the appropriate bandwidth in the scheduler for the
node representing the specified VF VSI.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This assignment statement is meaningless, because the statement
will execute to the tag "set_itr_now".
The clang_analyzer complains as follows:
drivers/net/ethernet/intel/e1000e/netdev.c:2552:3 warning:
Value stored to 'current_itr' is never read.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use single state machine for driver initialization and for service
initialized driver. The init state machine implemented in init_task()
is merged into the watchdog_task(). The init_task() function is
removed.
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This commit adds a new state, __IAVF_INIT_FAILED to the state machine.
From now on initialization functions report errors not by returning an
error value, but by changing the state to indicate that something went
wrong.
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace state changes of iavf state machine
with a method that also tracks the previous
state the machine was on.
This change is required for further work with
refactoring init and watchdog state machines.
Tracking of previous state would help us
recover iavf after failure has occurred.
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set(). ixgb_get_ee_mac_addr() is used with
a non-nevdev->dev_addr pointer so we can't deal with the problem
inside it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Go through the code base and use ice_for_each_* macros. While at it,
introduce ice_for_each_xdp_txq() macro that can be used for looping over
xdp_rings array.
Commit is not introducing any new functionality.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Under rare circumstances there might be a situation where a requirement
of having XDP Tx queue per CPU could not be fulfilled and some of the Tx
resources have to be shared between CPUs. This yields a need for placing
accesses to xdp_ring inside a critical section protected by spinlock.
These accesses happen to be in the hot path, so let's introduce the
static branch that will be triggered from the control plane when driver
could not provide Tx queue dedicated for XDP on each CPU.
Currently, the design that has been picked is to allow any number of XDP
Tx queues that is at least half of a count of CPUs that platform has.
For lower number driver will bail out with a response to user that there
were not enough Tx resources that would allow configuring XDP. The
sharing of rings is signalled via static branch enablement which in turn
indicates that lock for xdp_ring accesses needs to be taken in hot path.
Approach based on static branch has no impact on performance of a
non-fallback path. One thing that is needed to be mentioned is a fact
that the static branch will act as a global driver switch, meaning that
if one PF got out of Tx resources, then other PFs that ice driver is
servicing will suffer. However, given the fact that HW that ice driver
is handling has 1024 Tx queues per each PF, this is currently an
unlikely scenario.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Optimize Tx descriptor cleaning for XDP. Current approach doesn't
really scale and chokes when multiple flows are handled.
Introduce two ring fields, @next_dd and @next_rs that will keep track of
descriptor that should be looked at when the need for cleaning arise and
the descriptor that should have the RS bit set, respectively.
Note that at this point the threshold is a constant (32), but it is
something that we could make configurable.
First thing is to get away from setting RS bit on each descriptor. Let's
do this only once NTU is higher than the currently @next_rs value. In
such case, grab the tx_desc[next_rs], set the RS bit in descriptor and
advance the @next_rs by a 32.
Second thing is to clean the Tx ring only when there are less than 32
free entries. For that case, look up the tx_desc[next_dd] for a DD bit.
This bit is written back by HW to let the driver know that xmit was
successful. It will happen only for those descriptors that had RS bit
set. Clean only 32 descriptors and advance the DD bit.
Actual cleaning routine is moved from ice_napi_poll() down to the
ice_xmit_xdp_ring(). It is safe to do so as XDP ring will not get any
SKBs in there that would rely on interrupts for the cleaning. Nice side
effect is that for rare case of Tx fallback path (that next patch is
going to introduce) we don't have to trigger the SW irq to clean the
ring.
With those two concepts, ring is kept at being almost full, but it is
guaranteed that driver will be able to produce Tx descriptors.
This approach seems to work out well even though the Tx descriptors are
produced in one-by-one manner. Test was conducted with the ice HW
bombarded with packets from HW generator, configured to generate 30
flows.
Xdp2 sample yields the following results:
<snip>
proto 17: 79973066 pkt/s
proto 17: 80018911 pkt/s
proto 17: 80004654 pkt/s
proto 17: 79992395 pkt/s
proto 17: 79975162 pkt/s
proto 17: 79955054 pkt/s
proto 17: 79869168 pkt/s
proto 17: 79823947 pkt/s
proto 17: 79636971 pkt/s
</snip>
As that sample reports the Rx'ed frames, let's look at sar output.
It says that what we Rx'ed we do actually Tx, no noticeable drops.
Average: IFACE rxpck/s txpck/s rxkB/s txkB/s rxcmp/s txcmp/s rxmcst/s %ifutil
Average: ens4f1 79842324.00 79842310.40 4678261.17 4678260.38 0.00 0.00 0.00 38.32
with tx_busy staying calm.
When compared to a state before:
Average: IFACE rxpck/s txpck/s rxkB/s txkB/s rxcmp/s txcmp/s rxmcst/s %ifutil
Average: ens4f1 90919711.60 42233822.60 5327326.85 2474638.04 0.00 0.00 0.00 43.64
it can be observed that the amount of txpck/s is almost doubled, meaning
that the performance is improved by around 90%. All of this due to the
drops in the driver, previously the tx_busy stat was bumped at a 7mpps
rate.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With rings being split, it is now convenient to introduce a pointer to
XDP ring within the Rx ring. For XDP_TX workloads this means that
xdp_rings array access will be skipped, which was executed per each
processed frame.
Also, read the XDP prog once per NAPI and if prog is present, set up the
local xdp_ring pointer. Reading prog a single time was discussed in [1]
with some concern raised by Toke around dispatcher handling and having
the need for going through the RCU grace period in the ndo_bpf driver
callback, but ice currently is torning down NAPI instances regardless of
the prog presence on VSI.
Although the pointer to XDP ring introduced to Rx ring makes things a
lot slimmer/simpler, I still feel that single prog read per NAPI
lifetime is beneficial.
Further patch that will introduce the fallback path will also get a
profit from that as xdp_ring pointer will be set during the XDP rings
setup.
[1]: https://lore.kernel.org/bpf/87k0oseo6e.fsf@toke.dk/
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
xdp_frame is not needed for XDP_TX data path in ice driver case.
For this data path cleaning of sent descriptor will not happen anywhere
outside of the driver, which means that carrying the information about
the underlying memory model via xdp_frame will not be used. Therefore,
this conversion can be simply dropped, which would relieve CPU a bit.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There has been a long lasting issue of improper xdp_rings indexing for
XDP_TX and XDP_REDIRECT actions. Given that currently rx_ring->q_index
is mixed with smp_processor_id(), there could be a situation where Tx
descriptors are produced onto XDP Tx ring, but tail is never bumped -
for example pin a particular queue id to non-matching IRQ line.
Address this problem by ignoring the user ring count setting and always
initialize the xdp_rings array to be of num_possible_cpus() size. Then,
always use the smp_processor_id() as an index to xdp_rings array. This
provides serialization as at given time only a single softirq can run on
a particular CPU.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.
Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.
Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.
Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.
Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.
Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
