With previous changes to make the driver handle the TX ring size more
correctly, the default TX ring size of 64 appears to significantly
bottleneck TX performance to around 600 Mbps on a 1 Gbps link on ZynqMP.
Increasing this to 128 seems to bring performance up to near line rate and
shouldn't cause excess bufferbloat (this driver doesn't yet support modern
byte-based queue management).
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network driver documentation indicates we should be avoiding returning
NETDEV_TX_BUSY from ndo_start_xmit in normal cases, since it requires
the packets to be requeued. Instead the queue should be stopped after
a packet is added to the TX ring when there may not be enough room for an
additional one. Also, when TX ring entries are completed, we should only
wake the queue if we know there is room for another full maximally
fragmented packet.
Print a warning if there is insufficient space at the start of start_xmit,
since this should no longer happen.
Combined with increasing the default TX ring size (in a subsequent
patch), this appears to recover the TX performance lost by previous changes
to actually manage the TX ring state properly.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for the number of available TX ring slots was off by 1 since a
slot is required for the skb header as well as each fragment. This could
result in overwriting a TX ring slot that was still in use.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for whether a TX ring slot was available was incorrect,
since a slot which had been loaded with transmit data but the device had
not started transmitting would be treated as available, potentially
causing non-transmitted slots to be overwritten. The control field in
the descriptor should be checked, rather than the status field (which may
only be updated when the device completes the entry).
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will not work properly if the TX ring size is set to below
MAX_SKB_FRAGS + 1 since it needs to hold at least one full maximally
fragmented packet in the TX ring. Limit setting the ring size to below
this value.
Fixes: 8b09ca823f ("net: axienet: Make RX/TX ring sizes configurable")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was missing some required memory barriers:
Use dma_rmb to ensure we see all updates to the descriptor after we see
that an entry has been completed.
Use wmb and rmb to avoid stale descriptor status between the TX path and
TX complete IRQ path.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases where the Xilinx Ethernet core was used in 1000Base-X or
SGMII modes, which use the internal PCS/PMA PHY, and the MGT
transceiver clock source for the PCS was not running at the time the
FPGA logic was loaded, the core would come up in a state where the
PCS could not be found on the MDIO bus. To fix this, the Ethernet core
(including the PCS) should be reset after enabling the clocks, prior to
attempting to access the PCS using of_mdio_find_device.
Fixes: 1a02556086 (net: axienet: Properly handle PCS/PMA PHY for 1000BaseX mode)
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting the device, wait for the PhyRstCmplt bit to be set
in the interrupt status register before continuing initialization, to
ensure that the core is actually ready. When using an external PHY, this
also ensures we do not start trying to access the PHY while it is still
in reset. The PHY reset is initiated by the core reset which is
triggered just above, but remains asserted for 5ms after the core is
reset according to the documentation.
The MgtRdy bit could also be waited for, but unfortunately when using
7-series devices, the bit does not appear to work as documented (it
seems to behave as some sort of link state indication and not just an
indication the transceiver is ready) so it can't really be relied on for
this purpose.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous timeout of 1ms was too short to handle some cases where the
core is reset just after the input clocks were started, which will
be introduced in an upcoming patch. Increase the timeout to 50ms. Also
simplify the reset timeout checking to use read_poll_timeout.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
axienet has a PCS, but does not make use of the phylink PCS support.
Mark it was a pre-March 2020 driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
axienet has no special behaviour in its validation implementation, so
can be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode in the
validation function. Remove this to simplify it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the phy_interface_t bitmap for the Xilinx axienet driver with
interfaces modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding a fallthrough statement instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20210528195831.GA39131@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was only enabling the first clock on the device, regardless
of its name. However, this controller logic can have multiple clocks
which should all be enabled. Add support for enabling additional clocks.
The clock names used are matching those used in the Xilinx version of this
driver as well as the Xilinx device tree generator, except for mgt_clk
which is not present there.
For backward compatibility, if no named clocks are present, the first
clock present is used for determining the MDIO bus clock divider.
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In setups with fixed-link settings there is no mdio node in DTS.
axienet_probe() already handles that gracefully but lp->mii_bus is
then NULL.
Fix code that tries to blindly grab the MDIO lock by introducing two helper
functions that make the locking conditional.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver did not always clean up all allocated resources when probe
failed. Fix the probe cleanup path to clean up everything that was
allocated.
Fixes: 57baf8cc70 ("net: axienet: Handle deferred probe on clock properly")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer versions of the Xilinx AXI Ethernet core (specifically version 7.2 or
later) allow the core to be configured with a PHY interface mode of "Both",
allowing either 1000BaseX or SGMII modes to be selected at runtime. Add
support for this in the driver to allow better support for applications
which can use both fiber and copper SFP modules.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hook up the nway_reset ethtool operation to the corresponding phylink
function so that "ethtool -r" can be supported.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is set up to use a clock mapping in the device tree if it is
present, but still work without one for backward compatibility. However,
if getting the clock returns -EPROBE_DEFER, then we need to abort and
return that error from our driver initialization so that the probe can
be retried later after the clock is set up.
Move clock initialization to earlier in the process so we do not waste as
much effort if the clock is not yet available. Switch to use
devm_clk_get_optional and abort initialization on any error reported.
Also enable the clock regardless of whether the controller is using an MDIO
bus, as the clock is required in any case.
Fixes: 09a0354cad ("net: axienet: Use clock framework to get device clock rate")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO spec does not require an MDC at all times, only when MDIO
transactions are occurring. This patch allows the xilinx_axienet
driver to disable the MDC when not in use, and re-enable it when
needed. It also simplifies the driver by removing MDC disable
and enable in device reset sequence.
Signed-off-by: Clayton Rayment <clayton.rayment@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the axienet driver to properly support the Xilinx PCS/PMA PHY
component which is used for 1000BaseX and SGMII modes, including
properly configuring the auto-negotiation mode of the PHY and reading
the negotiated state from the PHY.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/20201028171429.1699922-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With all DMA address accesses wrapped, we can actually support 64-bit
DMA if this option was chosen at IP integration time.
If the IP has been configured for an address width greater than 32 bits,
we assume the full 64 bit DMA width is working. In practise this will be
limited by the actual system address bus width, which will ideally be the
same as the DMA IP address width.
If this is not the case, the actual width can still be configured using a
dma-ranges property in the parent of the MAC node.
This increases the DMA mask on those systems to let the kernel choose
buffers from memory at higher addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When newer revisions of the Axienet IP are configured for a 64-bit bus,
we *need* to write to the MSB part of the an address registers,
otherwise the IP won't recognise this as a DMA start condition.
This is even true when the actual DMA address comes from the lower 4 GB.
To autodetect this configuration, at probe time we write all 1's to such
an MSB register, and see if any bits stick. If this is configured for a
32-bit bus, those MSB registers are RES0, so reading back 0 indicates
that no MSB writes are necessary.
On the other hands reading anything other than 0 indicated the need to
write the MSB registers, so we set the respective flag.
The actual DMA mask stays at 32-bit for now. To help bisecting, a
separate patch will enable allocations from higher addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer revisions of the AXI DMA IP (>= v7.1) support 64-bit addresses,
both for the descriptors itself, as well as for the buffers they are
pointing to.
This is realised by adding "MSB" words for the next and phys pointer
right behind the existing address word, now named "LSB". These MSB words
live in formerly reserved areas of the descriptor.
If the hardware supports it, write both words when setting an address.
The buffer address is handled by two wrapper functions, the two
occasions where we set the next pointers are open coded.
For now this is guarded by a flag which we don't set yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer versions of the Xilink DMA IP support busses with more than 32
address bits, by introducing an MSB word for the registers holding DMA
pointers (tail/current, RX/TX descriptor addresses).
On IP configured for more than 32 bits, it is also *required* to write
both words, to let the IP recognise this as a start condition for an
MM2S request, for instance.
Wrap the DMA pointer writes with a separate function, to add this
functionality later. For now we stick to the lower 32 bits.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii-tool is useful for debugging, and all it requires to work is to wire
up the ioctl ops function pointer.
Add this to the axienet driver to enable mii-tool.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer revisions of the IP don't have these registers. Since we don't
really use them, just drop them from the ethtools dump.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the DT binding, the Ethernet core interrupt is optional.
Use platform_get_irq_optional() to avoid the error message when the
IRQ is not specified.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Especially with the default 32-bit DMA mask, DMA buffers are a limited
resource, so their allocation can fail.
So as the DMA API documentation requires, add error checking code after
dma_map_single() calls to catch the case where we run out of "low" memory.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the code that cleans up a number of connected TX descriptors,
as we will need it to properly roll back a failed _xmit() call.
There are subtle differences between cleaning up a successfully sent
chain (unknown number of involved descriptors, total data size needed)
and a chain that was about to set up (number of descriptors known), so
cater for those variations with some extra parameters.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 0 is a valid DMA address, we cannot use the physical address to
check whether a TX descriptor is valid and is holding a DMA mapping.
Use the "cntrl" member of the descriptor to make this decision, as it
contains at least the length of the buffer, so 0 points to an
uninitialised buffer.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When axienet_dma_bd_init() bails out during the initialisation process,
it might do so with parts of the structure already allocated and
initialised, while other parts have not been touched yet. Before
returning in this case, we call axienet_dma_bd_release(), which does not
take care of this corner case.
This is most obvious by the first loop happily dereferencing
lp->rx_bd_v, which we actually check to be non NULL *afterwards*.
Make sure we only unmap or free already allocated structures, by:
- directly returning with -ENOMEM if nothing has been allocated at all
- checking for lp->rx_bd_v to be non-NULL *before* using it
- only unmapping allocated DMA RX regions
This avoids NULL pointer dereferences when initialisation fails.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we fail allocating the DMA buffers in axienet_dma_bd_init(), we
report this error, but carry on with initialisation nevertheless.
This leads to a kernel panic when the driver later wants to send a
packet, as it uses uninitialised data structures.
Make the axienet_device_reset() routine return an error value, as it
contains the DMA buffer initialisation. Make sure we propagate the error
up the chain and eventually fail the driver initialisation, to avoid
relying on non-initialised buffers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA error handler routine is currently a tasklet, scheduled to run
after the DMA error IRQ was handled.
However it needs to take the MDIO mutex, which is not allowed to do in a
tasklet. A kernel (with debug options) complains consequently:
[ 614.050361] net eth0: DMA Tx error 0x174019
[ 614.064002] net eth0: Current BD is at: 0x8f84aa0ce
[ 614.080195] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:935
[ 614.109484] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 40, name: kworker/u4:4
[ 614.135428] 3 locks held by kworker/u4:4/40:
[ 614.149075] #0: ffff000879863328 ((wq_completion)rpciod){....}, at: process_one_work+0x1f0/0x6a8
[ 614.177528] #1: ffff80001251bdf8 ((work_completion)(&task->u.tk_work)){....}, at: process_one_work+0x1f0/0x6a8
[ 614.209033] #2: ffff0008784e0110 (sk_lock-AF_INET-RPC){....}, at: tcp_sendmsg+0x24/0x58
[ 614.235429] CPU: 0 PID: 40 Comm: kworker/u4:4 Not tainted 5.6.0-rc3-00926-g4a165a9d5921 #26
[ 614.260854] Hardware name: ARM Test FPGA (DT)
[ 614.274734] Workqueue: rpciod rpc_async_schedule
[ 614.289022] Call trace:
[ 614.296871] dump_backtrace+0x0/0x1a0
[ 614.308311] show_stack+0x14/0x20
[ 614.318751] dump_stack+0xbc/0x100
[ 614.329403] ___might_sleep+0xf0/0x140
[ 614.341018] __might_sleep+0x4c/0x80
[ 614.352201] __mutex_lock+0x5c/0x8a8
[ 614.363348] mutex_lock_nested+0x1c/0x28
[ 614.375654] axienet_dma_err_handler+0x38/0x388
[ 614.389999] tasklet_action_common.isra.15+0x160/0x1a8
[ 614.405894] tasklet_action+0x24/0x30
[ 614.417297] efi_header_end+0xe0/0x494
[ 614.429020] irq_exit+0xd0/0xd8
[ 614.439047] __handle_domain_irq+0x60/0xb0
[ 614.451877] gic_handle_irq+0xdc/0x2d0
[ 614.463486] el1_irq+0xcc/0x180
[ 614.473451] __tcp_transmit_skb+0x41c/0xb58
[ 614.486513] tcp_write_xmit+0x224/0x10a0
[ 614.498792] __tcp_push_pending_frames+0x38/0xc8
[ 614.513126] tcp_rcv_established+0x41c/0x820
[ 614.526301] tcp_v4_do_rcv+0x8c/0x218
[ 614.537784] __release_sock+0x5c/0x108
[ 614.549466] release_sock+0x34/0xa0
[ 614.560318] tcp_sendmsg+0x40/0x58
[ 614.571053] inet_sendmsg+0x40/0x68
[ 614.582061] sock_sendmsg+0x18/0x30
[ 614.593074] xs_sendpages+0x218/0x328
[ 614.604506] xs_tcp_send_request+0xa0/0x1b8
[ 614.617461] xprt_transmit+0xc8/0x4f0
[ 614.628943] call_transmit+0x8c/0xa0
[ 614.640028] __rpc_execute+0xbc/0x6f8
[ 614.651380] rpc_async_schedule+0x28/0x48
[ 614.663846] process_one_work+0x298/0x6a8
[ 614.676299] worker_thread+0x40/0x490
[ 614.687687] kthread+0x134/0x138
[ 614.697804] ret_from_fork+0x10/0x18
[ 614.717319] xilinx_axienet 7fe00000.ethernet eth0: Link is Down
[ 615.748343] xilinx_axienet 7fe00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
Since tasklets are not really popular anymore anyway, lets convert this
over to a work queue, which can sleep and thus can take the MDIO mutex.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters. No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the Xilinx AXI ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the mac_link_state() method to mac_pcs_get_state() to make it
clear that it should be returning the MACs PCS current state, which
is used for inband negotiation rather than just reading back what the
MAC has been configured for. Update the documentation to explicitly
mention that this is for inband.
We drop the return value as well; most of phylink doesn't check the
return value and it is not clear what it should do on error - instead
arrange for state->link to be false.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
