For the SDIO driver, the RESET/ENABLE pins of WILC1000 are controlled
through the SDIO power sequence driver. This commit adds analogous
support for the SPI driver. Specifically, during initialization, the
chip will be ENABLEd and taken out of RESET and during
deinitialization, the chip will be placed back into RESET and disabled
(both to reduce power consumption and to ensure the WiFi radio is
off).
Both RESET and ENABLE GPIOs are optional. However, if the ENABLE GPIO
is specified, then the RESET GPIO should normally also be specified as
otherwise there is no way to ensure proper timing of the ENABLE/RESET
sequence.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221212531.4011609-2-davidm@egauge.net
Smatch complains that there is a double free in probe:
drivers/net/wireless/microchip/wilc1000/spi.c:186 wilc_bus_probe() error: double free of 'spi_priv'
drivers/net/wireless/microchip/wilc1000/sdio.c:163 wilc_sdio_probe() error: double free of 'sdio_priv'
The problem is that wilc_netdev_cleanup() function frees "wilc->bus_data".
That's confusing and a layering violation. Leave the frees in probe(),
delete the free in wilc_netdev_cleanup(), and add some new frees to the
remove() functions.
Fixes: dc8b338f3b ("wilc1000: use goto labels on error path")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217150311.GC16611@kili
The name "wilc1000_spi" follows normal Linux conventions and also is
analogous to the SDIO driver, which uses "wilc1000_sdio".
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211209044411.3482259-2-davidm@egauge.net
The USE_SPI_DMA macro name suggests that it could be set to 1 to
control whether or not SPI DMA should be used. However, that's not
what it does. If set to 1, it'll set the SPI messages'
"is_dma_mapped" flag to true, even though the tx/rx buffers aren't
actually DMA mapped by the driver. In other words, setting this flag
to 1 will break the driver.
Best to clean up this confusion by removing the macro altogether.
There is no need to explicitly initialize "is_dma_mapped" because the
message is cleared to zero anyhow, so "is_dma_mapped" is set to false
by default.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211207002453.3193737-1-davidm@egauge.net
This eliminates warning message:
SPI driver WILC_SPI has no spi_device_id for microchip,wilc1000
and makes device-tree autoloading work.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211202045001.2901903-1-davidm@egauge.net
Instead of using double read for the same register, use the write register
command after the read command.
The correct sequence is to use the read value in write command instead of
reading the same register again.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-11-ajay.kathat@microchip.com
During WILC chip wake-up sequence, the clockless status register sometimes
reports failure even when the actual status is successful. So, for the
clockless register, remove the incorrect error status reporting during the
read and write command API's.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-8-ajay.kathat@microchip.com
For SPI bus, the register read fails after read/write to the clockless
register during chip wakeup sequence. Add workaround to send CMD_RESET
command during chip wake-up sequence to overcome the issue.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-7-ajay.kathat@microchip.com
Add reset/terminate/repeat command for SPI module. In case of SPI commands
failure, the host should issue a RESET command to WILC chip to recover
from any temporary bus error.
For now, the new command support is added and later the SPI read/write
API's would be modified to make use of these commands for retry mechanism
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-6-ajay.kathat@microchip.com
Move static "isinit" variable to wilc_spi structure to allow multiple
WILC1000 devices per machine.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210828151346.3012697-1-davidm@egauge.net
Use goto labels on error path for probe functions. This makes code easier
to read. With this introduce also netdev_cleanup and call it where
necessary.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210806081229.721731-2-claudiu.beznea@microchip.com
Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
requires an "rtc" clock name.
drivers/net/wireless/microchip/wilc1000/sdio.c is using "rtc" clock name
as well. Comply with the binding in wilc1000/spi.c too.
Fixes: 854d66df74 ("staging: wilc1000: look for rtc_clk clock in spi mode")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210428025445.81953-1-tudor.ambarus@microchip.com
The driver so far has always disabled CRC protection. This means any
data corruption that occurrs during the SPI transfers could go
undetected. This patch adds module parameters enable_crc7 and
enable_crc16 to selectively turn on CRC7 (for command transfers) and
CRC16 (for data transfers), respectively.
The default configuration remains unchanged, with both CRC7 and CRC16
off.
The performance impact of CRC was measured by running ttcp -t four
times in a row on a SAMA5 device:
CRC7 CRC16 Throughput: Standard deviation:
---- ----- ----------- -------------------
off off 1720 +/- 48 KB/s
on off 1658 +/- 58 KB/s
on on 1579 +/- 84 KB/s
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-4-davidm@egauge.net
After a DMA write to the WILC chip, check for and report any errors.
This is based on code from the wilc driver in the linux-at91
repository.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-3-davidm@egauge.net
The WILC1000 protocol control register has bits for enabling the CRCs
(CRC7 for commands and CRC16 for data) and to set the data packet
size. Define symbolic names for those so the code is more easily
understood.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-2-davidm@egauge.net
For CMD_SINGLE_READ and CMD_INTERNAL_READ, WILC may insert one or more
zero bytes between the command response and the DATA Start tag (0xf3).
This behavior appears to be undocumented in "ATWILC1000 USER GUIDE"
(https://tinyurl.com/4hhshdts) but we have observed 1-4 zero bytes
when the SPI bus operates at 48MHz and none when it operates at 1MHz.
This code is derived from the equivalent code of the wilc driver in
the linux-at91 repository.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-1-davidm@egauge.net
Added retry mechanism to ensure VMM enable bit is set during the
block transfer of data between host and WILC FW.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201208103739.28597-1-ajay.kathat@microchip.com
When devm_clk_get() returns -EPROBE_DEFER, spi_priv
should be freed just like when wilc_cfg80211_init()
fails.
Fixes: 854d66df74 ("staging: wilc1000: look for rtc_clk clock in spi mode")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200819115426.29852-1-dinghao.liu@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
