The uncore memory frequency value from the mailbox command
CONFIG_TDP_GET_MEM_FREQ needs to be scaled based on the platform for
display. There is no single constant multiplier.
This change introduces CPU model specific memory frequency multiplier.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a new command to get and set TRL (Turbo Ratio Limits). This will
help users to get/set TRL, when the direct MSR access is removed.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
When SST-PP feature is not present, the TRL (Turbo Ratio Limits)
is read from MSRs. This is done as the mailbox command will fail
on Skylake-X based platform. But for IceLake servers, mailbox
commands can still be used. So add a check to allow for non Skylake
based platforms to read from mail box commands.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/platform-driver-x86/57d6648282491906e0e1f70fe3b9a44f72cec90d.camel@intel.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The reported base-freq high-priority-cpu-list was potentially omitting
some cpus, due to incorrectly using a logical core count to constrain
the size of a physical punit core ID mask. We may need to read both high
and low PBF CORE_MASK values regardless of the logical core count.
Signed-off-by: Jonathan Doman <jonathan.doman@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The core mask display is wrong in some cases. This is showing more
cpus than the mask has. This is because mask is 64 bit but it used
with BIT() macro to get the presence of CPU which doesn't support
unsigned long long. Added a new macro for BIT_ULL and use that
to get the presence of a CPU.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
This change adds improved error display and handling for commands related
to turbo-freq feature. The changes include:
- Replace perror/fprintf with helpful error message
- Error for not specifying TDP level when required
- Show error for invalid bucket number
- Show message to enable core-power before enabling turbo-freq feature
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Improve output of perf-profile commands:
get-config-enabled
get-lock-status
Instead of showing 0/1, show meaningful strings. Also show error when
command is failed.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add a common API which can be used to print all error and information
messages. In this way a common format can be used.
For json output an error index in suffixed to make unique error key.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add additional information, which will allow user to detect available
features. This will allow users to check presence of features before
continue to test.
A sample output:
$sudo ./intel-speed-select --info
Intel(R) Speed Select Technology
Executing on CPU model:85[0x55]
Platform: API version : 1
Platform: Driver version : 1
Platform: mbox supported : 1
Platform: mmio supported : 0
Intel(R) SST-PP (feature perf-profile) is not supported
Only performance level 0 (base level) is present
TDP level change control is locked
Intel(R) SST-TF (feature turbo-freq) is supported
Intel(R) SST-BF (feature base-freq) is supported
Intel(R) SST-CP (feature core-power) is supported
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In addition to CLOS enable status, also show the core-power feature
status. This will help why clos enable status didn't give desired
results as the core-power feature may be disabled or unsupported.
The new display looks as follows:
$intel-speed-select core-power info
Intel(R) Speed Select Technology
..
package-0
die-0
cpu-0
core-power
support-status:supported
enable-status:enabled
clos-enable-status:1
priority-type:0
In the above display "support-status" and "enable-status", shows the
status of the core-power feature and "clos-enable-status", shows the
status of the clos.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It is possible that BIOS may not enable core-power feature. In this case
this additional interface will allow to enable from this utility. Also
the information dump, includes the current status of core-power.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some firmware implementation gives error when a command is sent get mask
for core count 32-61. So use core count to decide.
But there is no function to get core count. So introduce one function to
get core count.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There are some platforms, where there limited support of Intel(R) SST
features. Here perf-profile has only one base configuration and limited
support of commands. But still has support for discovery of base-freq and
turbo-freq features. So it is important to show minimum features to use
base-freq and turbo-freq features.
Here the change are:
- When there is no support of CONFIG_TDP_GET_LEVELS_INFO, then instead
of treating this as fatal error, treat this with number of config levels
= 0, that means only base level 0 is present.
- There is no support of mail box commands to get base frequencies or
turbo frequencies. Here present base frequency by reading cpufreq
base freq and turbo frequency by reading MSR 0x1AD.
- Don't display any field, which has value == 0.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
commit "c016ae8f9fa04d361efc8629de49ad3af12b5262
"tools/power/x86/intel-speed-select: Output success/failed for command
output" introduced a regression in perf-profile outputs. With this
the result field is changed to string interpreting every non zero
value as errors. But these commands display on zero (>0) result.
For example before this commit the display was:
package-1
die-0
cpu-14
get-config-levels:4
Here the get-config-levels is interpreted as error and displayed
as error with the above commit:
package-1
die-0
cpu-14
get-config-levels:failed(error 4)
Fix this issue by not using isst_display_result() to display such results,
but define a new function which formats this data and prints.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add additional command to get the clos enable and priority type. The
current info option is actually dumping per clos QOS config, so name
the command appropriately to get-config.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Format the get-assoc command output consistant with other commands.
For example:
Intel(R) Speed Select Technology
Executing on CPU model:142[0x8e]
package-0
die-0
cpu-0
get-assoc
clos:0
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Using enable core mask, do online offline CPUs. There is a new option
--online|-o for set-config-level.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Read the bucket and core count relationship via MSR and display
when displaying turbo ratio limits.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The Intel(R) Speed select technologies contains four features.
Performance profile:An non architectural mechanism that allows multiple
optimized performance profiles per system via static and/or dynamic
adjustment of core count, workload, Tjmax, and TDP, etc. aka ISS
in the documentation.
Base Frequency: Enables users to increase guaranteed base frequency on
certain cores (high priority cores) in exchange for lower base frequency
on remaining cores (low priority cores). aka PBF in the documenation.
Turbo frequency: Enables the ability to set different turbo ratio limits
to cores based on priority. aka FACT in the documentation.
Core power: An Interface that allows user to define per core/tile
priority.
There is a multi level help for commands and options. This can be used
to check required arguments for each feature and commands for the
feature.
To start navigating the features start with
$sudo intel-speed-select --help
For help on a specific feature for example
$sudo intel-speed-select perf-profile --help
To get help for a command for a feature for example
$sudo intel-speed-select perf-profile get-lock-status --help
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
