Stick with pr_info message because session reset isn't an error most of
the time. When it is (i.e. if the server denies the reconnect attempt),
we get a bunch of other pr_err messages.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
con->peer_global_seq is part of session state. Clear it when
the server tells us to reset, not just in ceph_con_close().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Move protocol reset bits into ceph_con_reset_protocol(), leaving
just session reset bits.
Note that con->out_skip is now reset on faults. This fixes a crash
in the case of a stateful session getting a fault while in the middle
of revoking a message.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
A fault due to a version mismatch or a feature set mismatch used to be
treated differently from other faults: the connection would get closed
without trying to reconnect and there was a ->bad_proto() connection op
for notifying about that.
This changed a long time ago, see commits 6384bb8b8e ("libceph: kill
bad_proto ceph connection op") and 0fa6ebc600 ("libceph: fix protocol
feature mismatch failure path"). Nowadays these aren't any different
from other faults (i.e. we try to reconnect even though the mismatch
won't resolve until the server is replaced). reset_connection() calls
there are rather confusing because reset_connection() resets a session
together an individual instance of the protocol. This is cleaned up
in the next patch.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The current setting allows the backoff to climb up to 5 minutes. This
is too high -- it becomes hard to tell whether the client is stuck on
something or just in backoff.
In userspace, ms_max_backoff is defaulted to 15 seconds. Let's do the
same.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Pull crypto updates from Herbert Xu:
"API:
- Add speed testing on 1420-byte blocks for networking
Algorithms:
- Improve performance of chacha on ARM for network packets
- Improve performance of aegis128 on ARM for network packets
Drivers:
- Add support for Keem Bay OCS AES/SM4
- Add support for QAT 4xxx devices
- Enable crypto-engine retry mechanism in caam
- Enable support for crypto engine on sdm845 in qce
- Add HiSilicon PRNG driver support"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (161 commits)
crypto: qat - add capability detection logic in qat_4xxx
crypto: qat - add AES-XTS support for QAT GEN4 devices
crypto: qat - add AES-CTR support for QAT GEN4 devices
crypto: atmel-i2c - select CONFIG_BITREVERSE
crypto: hisilicon/trng - replace atomic_add_return()
crypto: keembay - Add support for Keem Bay OCS AES/SM4
dt-bindings: Add Keem Bay OCS AES bindings
crypto: aegis128 - avoid spurious references crypto_aegis128_update_simd
crypto: seed - remove trailing semicolon in macro definition
crypto: x86/poly1305 - Use TEST %reg,%reg instead of CMP $0,%reg
crypto: x86/sha512 - Use TEST %reg,%reg instead of CMP $0,%reg
crypto: aesni - Use TEST %reg,%reg instead of CMP $0,%reg
crypto: cpt - Fix sparse warnings in cptpf
hwrng: ks-sa - Add dependency on IOMEM and OF
crypto: lib/blake2s - Move selftest prototype into header file
crypto: arm/aes-ce - work around Cortex-A57/A72 silion errata
crypto: ecdh - avoid unaligned accesses in ecdh_set_secret()
crypto: ccree - rework cache parameters handling
crypto: cavium - Use dma_set_mask_and_coherent to simplify code
crypto: marvell/octeontx - Use dma_set_mask_and_coherent to simplify code
...
If we're shifting the page data to the right, and this happens to be a
sparse page array, then we may need to allocate new pages in order to
receive the data.
Reported-by: "Mkrtchyan, Tigran" <tigran.mkrtchyan@desy.de>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
There are a number of xdr helpers for struct xdr_buf that do not change
the structure itself. Mark those as taking const pointers for
documentation purposes.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Move the setting of the xdr_stream 'nwords' field into the helpers that
reset the xdr_stream cursor.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
We do want to try to grow the buffer if possible, but if that attempt
fails, we still want to move the data and truncate the XDR message.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
The main use case right now for xdr_align_data() is to shift the page
data to the left, and in practice shrink the total XDR data buffer.
This patch ensures that we fix up the accounting for the buffer length
as we shift that data around.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Olga K. observed that rpcrdma_marsh_req() allocates sparse pages
only when it has determined that a Reply chunk is necessary. There
are plenty of cases where no Reply chunk is needed, but the
XDRBUF_SPARSE_PAGES flag is set. The result would be a crash in
rpcrdma_inline_fixup() when it tries to copy parts of the received
Reply into a missing page.
To avoid crashing, handle sparse page allocation up front.
Until XATTR support was added, this issue did not appear often
because the only SPARSE_PAGES consumer always expected a reply large
enough to always require a Reply chunk.
Reported-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
When receiving pages data, return value 'ret' when positive includes
`buf->page_base`, so we should subtract that before it is used for
changing `offset` and comparing against `want`.
This was discovered on the very rare cases where the server returned a
chunk of bytes that when added to the already received amount of bytes
for the pages happened to match the current `recv.len`, for example
on this case:
buf->page_base : 258356
actually received from socket: 1740
ret : 260096
want : 260096
In this case neither of the two 'if ... goto out' trigger, and we
continue to tail parsing.
Worth to mention that the ensuing EMSGSIZE from the continued execution of
`xs_read_xdr_buf` may be observed by an application due to 4 superfluous
bytes being added to the pages data.
Fixes: 277e4ab7d5 ("SUNRPC: Simplify TCP receive code by switching to using iterators")
Signed-off-by: Dan Aloni <dan@kernelim.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
According to the X.25 documentation, there was a plan to implement
X.25-over-802.2-LLC. It never finished but left various code stubs in the
X.25 code. At this time it is unlikely that it would ever finish so it
may be better to remove those code stubs.
Also change the documentation to make it clear that this is not a ongoing
plan anymore. Change words like "will" to "could", "would", etc.
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201209033346.83742-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On a few of our systems, I found frequent 'unshare(CLONE_NEWNET)' calls
make the number of active slab objects including 'sock_inode_cache' type
rapidly and continuously increase. As a result, memory pressure occurs.
In more detail, I made an artificial reproducer that resembles the
workload that we found the problem and reproduce the problem faster. It
merely repeats 'unshare(CLONE_NEWNET)' 50,000 times in a loop. It takes
about 2 minutes. On 40 CPU cores / 70GB DRAM machine, the available
memory continuously reduced in a fast speed (about 120MB per second,
15GB in total within the 2 minutes). Note that the issue don't
reproduce on every machine. On my 6 CPU cores machine, the problem
didn't reproduce.
'cleanup_net()' and 'fqdir_work_fn()' are functions that deallocate the
relevant memory objects. They are asynchronously invoked by the work
queues and internally use 'rcu_barrier()' to ensure safe destructions.
'cleanup_net()' works in a batched maneer in a single thread worker,
while 'fqdir_work_fn()' works for each 'fqdir_exit()' call in the
'system_wq'. Therefore, 'fqdir_work_fn()' called frequently under the
workload and made the contention for 'rcu_barrier()' high. In more
detail, the global mutex, 'rcu_state.barrier_mutex' became the
bottleneck.
This commit avoids such contention by doing the 'rcu_barrier()' and
subsequent lightweight works in a batched manner, as similar to that of
'cleanup_net()'. The fqdir hashtable destruction, which is done before
the 'rcu_barrier()', is still allowed to run in parallel for fast
processing, but this commit makes it to use a dedicated work queue
instead of the 'system_wq', to make sure that the number of threads is
bounded.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20201211112405.31158-1-sjpark@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-12-12
Just one patch this time:
1) Redact the SA keys with kernel lockdown confidentiality.
If enabled, no secret keys are sent to uuserspace.
From Antony Antony.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next:
xfrm: redact SA secret with lockdown confidentiality
====================
Link: https://lore.kernel.org/r/20201212085737.2101294-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds three new netlink attributes to encapsulate a list of
expressions per set elements:
- NFTA_SET_EXPRESSIONS: this attribute provides the set definition in
terms of expressions. New set elements get attached the list of
expressions that is specified by this new netlink attribute.
- NFTA_SET_ELEM_EXPRESSIONS: this attribute allows users to restore (or
initialize) the stateful information of set elements when adding an
element to the set.
- NFTA_DYNSET_EXPRESSIONS: this attribute specifies the list of
expressions that the set element gets when it is inserted from the
packet path.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch replaces NFT_SET_EXPR by NFT_SET_EXT_EXPRESSIONS. This new
extension allows to attach several expressions to one set element (not
only one single expression as NFT_SET_EXPR provides). This patch
prepares for support for several expressions per set element in the
netlink userspace API.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* validate key indices for key deletion
* more preamble support in mac80211
* various 6 GHz scan fixes/improvements
* a common SAR power limitations API
* various small fixes & code improvements
-----BEGIN PGP SIGNATURE-----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=+qd6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-12-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A new set of wireless changes:
* validate key indices for key deletion
* more preamble support in mac80211
* various 6 GHz scan fixes/improvements
* a common SAR power limitations API
* various small fixes & code improvements
* tag 'mac80211-next-for-net-next-2020-12-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (35 commits)
mac80211: add ieee80211_set_sar_specs
nl80211: add common API to configure SAR power limitations
mac80211: fix a mistake check for rx_stats update
mac80211: mlme: save ssid info to ieee80211_bss_conf while assoc
mac80211: Update rate control on channel change
mac80211: don't filter out beacons once we start CSA
mac80211: Fix calculation of minimal channel width
mac80211: ignore country element TX power on 6 GHz
mac80211: use bitfield helpers for BA session action frames
mac80211: support Rx timestamp calculation for all preamble types
mac80211: don't set set TDLS STA bandwidth wider than possible
mac80211: support driver-based disconnect with reconnect hint
cfg80211: support immediate reconnect request hint
mac80211: use struct assignment for he_obss_pd
cfg80211: remove struct ieee80211_he_bss_color
nl80211: validate key indexes for cfg80211_registered_device
cfg80211: include block-tx flag in channel switch started event
mac80211: disallow band-switch during CSA
ieee80211: update reduced neighbor report TBTT info length
cfg80211: Save the regulatory domain when setting custom regulatory
...
====================
Link: https://lore.kernel.org/r/20201211142552.209018-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the set infrastucture allows for one single expressions per
element. This patch extends the existing infrastructure to allow for up
to two expressions. This is not updating the netlink API yet, this is
coming as an initial preparation patch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
DESTROY events do not include the remaining timeout.
Add the timeout if the entry was removed explicitly. This can happen
when a conntrack gets deleted prematurely, e.g. due to a tcp reset,
module removal, netdev notifier (nat/masquerade device went down),
ctnetlink and so on.
Add the protocol state too for the destroy message to check for abnormal
state on connection termination.
Joint work with Pablo.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change registers ieee80211_set_sar_specs to
mac80211_config_ops, so cfg80211 can call it.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Abhishek Kumar <kuabhs@chromium.org>
Link: https://lore.kernel.org/r/20201203103728.3034-3-cjhuang@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NL80211_CMD_SET_SAR_SPECS is added to configure SAR from
user space. NL80211_ATTR_SAR_SPEC is used to pass the SAR
power specification when used with NL80211_CMD_SET_SAR_SPECS.
Wireless driver needs to register SAR type, supported frequency
ranges to wiphy, so user space can query it. The index in
frequency range is used to specify which sub band the power
limitation applies to. The SAR type is for compatibility, so later
other SAR mechanism can be implemented without breaking the user
space SAR applications.
Normal process is user space queries the SAR capability, and
gets the index of supported frequency ranges and associates the
power limitation with this index and sends to kernel.
Here is an example of message send to kernel:
8c 00 00 00 08 00 01 00 00 00 00 00 38 00 2b 81
08 00 01 00 00 00 00 00 2c 00 02 80 14 00 00 80
08 00 02 00 00 00 00 00 08 00 01 00 38 00 00 00
14 00 01 80 08 00 02 00 01 00 00 00 08 00 01 00
48 00 00 00
NL80211_CMD_SET_SAR_SPECS: 0x8c
NL80211_ATTR_WIPHY: 0x01(phy idx is 0)
NL80211_ATTR_SAR_SPEC: 0x812b (NLA_NESTED)
NL80211_SAR_ATTR_TYPE: 0x00 (NL80211_SAR_TYPE_POWER)
NL80211_SAR_ATTR_SPECS: 0x8002 (NLA_NESTED)
freq range 0 power: 0x38 in 0.25dbm unit (14dbm)
freq range 1 power: 0x48 in 0.25dbm unit (18dbm)
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Abhishek Kumar <kuabhs@chromium.org>
Link: https://lore.kernel.org/r/20201203103728.3034-2-cjhuang@codeaurora.org
[minor edits, NLA parse cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It should be !is_multicast_ether_addr() in ieee80211_rx_h_sta_process()
for the rx_stats update, below commit remove the !, this patch is to
change it back.
It lead the rx rate "iw wlan0 station dump" become invalid for some
scenario when IEEE80211_HW_USES_RSS is set.
Fixes: 09a740ce35 ("mac80211: receive and process S1G beacons")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/1607483189-3891-1-git-send-email-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ssid info of ieee80211_bss_conf is filled in ieee80211_start_ap()
for AP mode. For STATION mode, it is empty, save the info from struct
ieee80211_mgd_assoc_data, the struct ieee80211_mgd_assoc_data will be
freed after assoc, so the ssid info of ieee80211_mgd_assoc_data can not
access after assoc, save ssid info to ieee80211_bss_conf, then ssid info
can be still access after assoc.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/1607312195-3583-2-git-send-email-wgong@codeaurora.org
[reset on disassoc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A channel change or a channel bandwidth change can impact the
rate control logic. However, the rate control logic was not updated
before/after such a change, which might result in unexpected
behavior.
Fix this by updating the stations rate control logic when the
corresponding channel context changes.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.600d967fe3c9.I48305f25cfcc9c032c77c51396e9e9b882748a86@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I hit a bug in which we started a CSA with an action frame,
but the AP changed its mind and didn't change the beacon.
The CSA wasn't cancelled and we lost the connection.
The beacons were ignored because they never changed: they
never contained any CSA IE. Because they never changed, the
CRC of the beacon didn't change either which made us ignore
the beacons instead of processing them.
Now what happens is:
1) beacon has CRC X and it is valid. No CSA IE in the beacon
2) as long as beacon's CRC X, don't process their IEs
3) rx action frame with CSA
4) invalidate the beacon's CRC
5) rx beacon, CRC is still X, but now it is invalid
6) process the beacon, detect there is no CSA IE
7) abort CSA
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.83470b8407e6.I739b907598001362744692744be15335436b8351@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When calculating the minimal channel width for channel context,
the current operation Rx channel width of a station was used and not
the overall channel width capability of the station, i.e., both for
Tx and Rx.
Fix ieee80211_get_sta_bw() to use the maximal channel width the
station is capable. While at it make the function static.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.4387040b99a0.I74bcf19238f75a5960c4098b10e355123d933281@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Updates to the 802.11ax draft are coming that deprecate the
country element in favour of the transmit power envelope
element, and make the maximum transmit power level field in
the triplets reserved, so if we parse them we'd use 0 dBm
transmit power.
Follow suit and completely ignore the element on 6 GHz for
purposes of determining TX power.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.9abf9f6b4f88.Icb6e52af586edcc74f1f0360e8f6fc9ef2bfe8f5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we set up a TDLS station, we set sta->sta.bandwidth solely based
on the capabilities, because the "what's the current bandwidth" check
is bypassed and only applied for other types of stations.
This leads to the unfortunate scenario that the sta->sta.bandwidth is
160 MHz if both stations support it, but we never actually configure
this bandwidth unless the AP is already using 160 MHz; even for wider
bandwidth support we only go up to 80 MHz (at least right now.)
For iwlwifi, this can also lead to firmware asserts, telling us that
we've configured the TX rates for a higher bandwidth than is actually
available due to the PHY configuration.
For non-TDLS, we check against the interface's requested bandwidth,
but we explicitly skip this check for TDLS to cope with the wider BW
case. Change this to
(a) still limit to the TDLS peer's own chandef, which gets factored
into the overall PHY configuration we request from the driver,
and
(b) limit it to when the TDLS peer is authorized, because it's only
factored into the channel context in this case.
Fixes: 504871e602 ("mac80211: fix bandwidth computation for TDLS peers")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.fcc7d29c4590.I11f77e9e25ddf871a3c8d5604650c763e2c5887a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't really use this struct, we're now using
struct cfg80211_he_bss_color instead.
Change the one place in mac80211 that's using the old
name to use struct assignment instead of memcpy() and
thus remove the wrong sizeof while at it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.f6698d97ae4e.Iba2dffcb79c4ab80bde7407609806010b55edfdf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
syzbot discovered a bug in which an OOB access was being made because
an unsuitable key_idx value was wrongly considered to be acceptable
while deleting a key in nl80211_del_key().
Since we don't know the cipher at the time of deletion, if
cfg80211_validate_key_settings() were to be called directly in
nl80211_del_key(), even valid keys would be wrongly determined invalid,
and deletion wouldn't occur correctly.
For this reason, a new function - cfg80211_valid_key_idx(), has been
created, to determine if the key_idx value provided is valid or not.
cfg80211_valid_key_idx() is directly called in 2 places -
nl80211_del_key(), and cfg80211_validate_key_settings().
Reported-by: syzbot+49d4cab497c2142ee170@syzkaller.appspotmail.com
Tested-by: syzbot+49d4cab497c2142ee170@syzkaller.appspotmail.com
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20201204215825.129879-1-anant.thazhemadam@gmail.com
Cc: stable@vger.kernel.org
[also disallow IGTK key IDs if no IGTK cipher is supported]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP advertises a band switch during CSA, we will not have
the right information to continue working with it, since it will
likely (have to) change its capabilities and we don't track any
capability changes at all. Additionally, we store e.g. supported
rates per band, and that information would become invalid.
Since this is a fringe scenario, just disconnect explicitly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201129172929.0e2327107c06.I461adb07704e056b054a4a7c29b80c95a9f56637@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Accept a scan request with the duration set even if the driver
does not support setting the scan dwell. The duration can be used
as a hint to the driver, but the driver may use its internal logic
for setting the scan dwell.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201129172929.9491a12f9226.Ia9c5b24fcefc5ce5592537507243391633a27e5f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
