Make use of the existing linkmode helpers for converting PHY EEE
register values into links modes, now that ethtool_keee uses link
modes, rather than u32 values.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Energy Efficient Ethernet should always be negotiated with the link
peer. Don't include SUPPORTED_Autoneg in the results of get_eee() for
supported, advertised or lp_advertised, since it is
assumed. Additionally, ethtool(1) ignores the set bit, and no other
driver sets this.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for LEDs on i225/i226. The LEDs can be controlled via sysfs
from user space using the netdev trigger. The LEDs are named as
igc-<bus><device>-<led> to be easily identified.
Offloading link speed and activity are supported. Other modes are simulated
in software by using on/off. Tested on Intel i225.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240213184138.1483968-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
PHY_CONTROL register works as defined in the IEEE 802.3 specification
(IEEE 802.3-2008 22.2.4.1). Tidy up the temporary workaround.
User impact: PHY can now be powered down when the ethernet link is down.
Testing hints: ip link set down <device> (or just disconnect the
ethernet cable).
Oldest tested NVM version is: 1045:740.
Fixes: 5586838fe9 ("igc: Add code for PHY support")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
All filtering parameters such as EtherType and VLAN TCI are stored in host
byte order except for the VLAN EtherType. Unify it.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
All igc filter implementations use netdev_*() printing functions except for
the flex filters. Unify it.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use reverse xmas tree coding style convention in igc_add_flex_filter().
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This is in preparation of using the existing names for linkmode
bitmaps.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-01-03 (i40e, ice, igc)
This series contains updates to i40e, ice, and igc drivers.
Ke Xiao fixes use after free for unicast filters on i40e.
Andrii restores VF MSI-X flag after PCI reset on i40e.
Paul corrects admin queue link status structure to fulfill firmware
expectations for ice.
Rodrigo Cataldo corrects value used for hicredit calculations on igc.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Fix hicredit calculation
ice: fix Get link status data length
i40e: Restore VF MSI-X state during PCI reset
i40e: fix use-after-free in i40e_aqc_add_filters()
====================
Link: https://lore.kernel.org/r/20240103193254.822968-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the Intel Software Manual for I225, Section 7.5.2.7,
hicredit should be multiplied by the constant link-rate value, 0x7736.
Currently, the old constant link-rate value, 0x7735, from the boards
supported on igb are being used, most likely due to a copy'n'paste, as
the rest of the logic is the same for both drivers.
Update hicredit accordingly.
Fixes: 1ab011b0bf ("igc: Add support for CBS offloading")
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Rodrigo Cataldo <rodrigo.cadore@l-acoustics.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the driver accepts VLAN EtherType steering rules regardless of
the configured mask. And things might fail silently or with confusing error
messages to the user. The VLAN EtherType can only be matched by full
mask. Therefore, add a check for that.
For instance the following rule is invalid, but the driver accepts it and
ignores the user specified mask:
|root@host:~# ethtool -N enp3s0 flow-type ether vlan-etype 0x8100 \
| m 0x00ff action 0
|Added rule with ID 63
|root@host:~# ethtool --show-ntuple enp3s0
|4 RX rings available
|Total 1 rules
|
|Filter: 63
| Flow Type: Raw Ethernet
| Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Ethertype: 0x0 mask: 0xFFFF
| VLAN EtherType: 0x8100 mask: 0x0
| VLAN: 0x0 mask: 0xffff
| User-defined: 0x0 mask: 0xffffffffffffffff
| Action: Direct to queue 0
After:
|root@host:~# ethtool -N enp3s0 flow-type ether vlan-etype 0x8100 \
| m 0x00ff action 0
|rmgr: Cannot insert RX class rule: Operation not supported
Fixes: 2b477d057e ("igc: Integrate flex filter into ethtool ops")
Suggested-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the driver accepts VLAN TCI steering rules regardless of the
configured mask. And things might fail silently or with confusing error
messages to the user.
There are two ways to handle the VLAN TCI mask:
1. Match on the PCP field using a VLAN prio filter
2. Match on complete TCI field using a flex filter
Therefore, add checks and code for that.
For instance the following rule is invalid and will be converted into a
VLAN prio rule which is not correct:
|root@host:~# ethtool -N enp3s0 flow-type ether vlan 0x0001 m 0xf000 \
| action 1
|Added rule with ID 61
|root@host:~# ethtool --show-ntuple enp3s0
|4 RX rings available
|Total 1 rules
|
|Filter: 61
| Flow Type: Raw Ethernet
| Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Ethertype: 0x0 mask: 0xFFFF
| VLAN EtherType: 0x0 mask: 0xffff
| VLAN: 0x1 mask: 0x1fff
| User-defined: 0x0 mask: 0xffffffffffffffff
| Action: Direct to queue 1
After:
|root@host:~# ethtool -N enp3s0 flow-type ether vlan 0x0001 m 0xf000 \
| action 1
|rmgr: Cannot insert RX class rule: Operation not supported
Fixes: 7991487ecb ("igc: Allow for Flex Filters to be installed")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the driver allows to configure matching by VLAN EtherType.
However, the retrieval function does not report it back to the user. Add
it.
Before:
|root@host:~# ethtool -N enp3s0 flow-type ether vlan-etype 0x8100 action 0
|Added rule with ID 63
|root@host:~# ethtool --show-ntuple enp3s0
|4 RX rings available
|Total 1 rules
|
|Filter: 63
| Flow Type: Raw Ethernet
| Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Ethertype: 0x0 mask: 0xFFFF
| Action: Direct to queue 0
After:
|root@host:~# ethtool -N enp3s0 flow-type ether vlan-etype 0x8100 action 0
|Added rule with ID 63
|root@host:~# ethtool --show-ntuple enp3s0
|4 RX rings available
|Total 1 rules
|
|Filter: 63
| Flow Type: Raw Ethernet
| Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Ethertype: 0x0 mask: 0xFFFF
| VLAN EtherType: 0x8100 mask: 0x0
| VLAN: 0x0 mask: 0xffff
| User-defined: 0x0 mask: 0xffffffffffffffff
| Action: Direct to queue 0
Fixes: 2b477d057e ("igc: Integrate flex filter into ethtool ops")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor the igc driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired in a later patch.
@get@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor igc driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired in a later patch.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Cc: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This series is introducing the use of FIELD_GET and FIELD_PREP which
requires bitfield.h to be included. Fix all the includes in this one
change, and rearrange includes into alphabetical order to ease
readability and future maintenance.
virtchnl.h and it's usage was modified to have it's own includes as it
should. This required including bits.h for virtchnl.h.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The get/set_rxfh ethtool ops currently takes the rxfh (RSS) parameters
as direct function arguments. This will force us to change the API (and
all drivers' functions) every time some new parameters are added.
This is part 1/2 of the fix, as suggested in [1]:
- First simplify the code by always providing a pointer to all params
(indir, key and func); the fact that some of them may be NULL seems
like a weird historic thing or a premature optimization.
It will simplify the drivers if all pointers are always present.
- Then make the functions take a dev pointer, and a pointer to a
single struct wrapping all arguments. The set_* should also take
an extack.
Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1]
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-2-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch converts some basic cases of ethtool_sprintf() to
ethtool_puts().
The conversions are used in cases where ethtool_sprintf() was being used
with just two arguments:
| ethtool_sprintf(&data, buffer[i].name);
or when it's used with format string: "%s"
| ethtool_sprintf(&data, "%s", buffer[i].name);
which both now become:
| ethtool_puts(&data, buffer[i].name);
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for using Timer 1 (i225/i226 have 4 timer registers) as a
free-running clock (the "cycles" clock) in addition to Timer 0 (the
default, "adjustable clock"). The objective is to allow taprio/etf
offloading to coexist with PTP vclocks.
Besides the implementation of .getcyclesx64() for i225/i226, to keep
timestamping working when vclocks are in use, we also need to add
support for TX and RX timestamping using the free running timer, when
the requesting socket is bound to a vclock.
On the RX side, i225/i226 can be configured to store the values of two
timers in the received packet metadata area, so it's a matter of
configuring the right registers and retrieving the right timestamp.
The TX is a bit more involved because the hardware stores a single
timestamp (with the selected timer in the TX descriptor) into one of
the timestamp registers.
Note some changes at how the timestamps are done for RX, the
conversion and adjustment of timestamps are now done closer to the
consumption of the timestamp instead of near the reception.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We can re-use the IGC_SET_FLAG() macro to simplify setting some values
in the TX data descriptor. With the macro it's easier to get the
meaning of the operations.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The 'ethtool_convert_link_mode_to_legacy_u32' method does not allow us to
advertise 2500M speed support and TP (twisted pair) properly. Convert to
'ethtool_link_ksettings_test_link_mode' to advertise supported speed and
eliminate ambiguity.
Fixes: 8c5ad0dae9 ("igc: Add ethtool support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Suggested-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231019203641.3661960-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
`strncpy` is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect netdev->name to be NUL-terminated based on its use with format
strings:
| if (q_vector->rx.ring && q_vector->tx.ring)
| sprintf(q_vector->name, "%s-TxRx-%u", netdev->name,
Furthermore, we do not need NUL-padding as netdev is already
zero-allocated:
| netdev = alloc_etherdev_mq(sizeof(struct igc_adapter),
| IGC_MAX_TX_QUEUES);
...
alloc_etherdev() -> alloc_etherdev_mq() -> alloc_etherdev_mqs() ->
alloc_netdev_mqs() ...
| p = kvzalloc(alloc_size, GFP_KERNEL_ACCOUNT | __GFP_RETRY_MAYFAIL);
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231017190411.2199743-10-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Get ahead of the game and fix all the -Wformat=2 noted warnings in the
intel drivers directory.
There are one set of i40e and iavf warnings I couldn't figure out how to
fix because the driver is already using vsnprintf without an explicit
"const char *" format string.
Tested with both gcc-12 and clang-15. I found gcc-12 runs clean after
this series but clang-15 is a little worried about the vsnprintf lines.
summary of warnings:
drivers/net/ethernet/intel/fm10k/fm10k_ethtool.c:148:34: warning: format string is not a string literal [-Wformat-nonliteral]
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c:1416:24: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c:1416:24: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c:1421:6: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c:1421:6: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/igc/igc_ethtool.c:776:24: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/igc/igc_ethtool.c:776:24: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/igc/igc_ethtool.c:779:6: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/igc/igc_ethtool.c:779:6: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/iavf/iavf_ethtool.c:199:34: warning: format string is not a string literal [-Wformat-nonliteral]
drivers/net/ethernet/intel/igb/igb_ethtool.c:2360:6: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/igb/igb_ethtool.c:2360:6: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/igb/igb_ethtool.c:2363:6: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/igb/igb_ethtool.c:2363:6: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/i40e/i40e_ethtool.c:208:34: warning: format string is not a string literal [-Wformat-nonliteral]
drivers/net/ethernet/intel/i40e/i40e_ethtool.c:2515:23: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/i40e/i40e_ethtool.c:2515:23: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/i40e/i40e_ethtool.c:2519:23: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/i40e/i40e_ethtool.c:2519:23: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/ice/ice_ethtool.c:1064:6: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/ice/ice_ethtool.c:1064:6: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/ice/ice_ethtool.c:1084:6: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/ice/ice_ethtool.c:1084:6: note: treat the string as an argument to avoid this
drivers/net/ethernet/intel/ice/ice_ethtool.c:1100:24: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
drivers/net/ethernet/intel/ice/ice_ethtool.c:1100:24: note: treat the string as an argument to avoid this
Suggested-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231017190411.2199743-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When users attempt to obtain the coalesce setting using the
ethtool command, current code always returns 0 for tx-usecs.
This is because I225/6 always uses a queue pair setting, hence
tx_coalesce_usecs does not return a value during the
igc_ethtool_get_coalesce() callback process. The pair queue
condition checking in igc_ethtool_get_coalesce() is removed by
this patch so that the user gets information of the value of tx-usecs.
Even if i225/6 is using queue pair setting, there is no harm in
notifying the user of the tx-usecs. The implementation of the current
code may have previously been a copy of the legacy code i210.
Since I225 has the queue pair setting enabled, tx-usecs will always adhere
to the user-set rx-usecs value. An error message will appear when the user
attempts to set the tx-usecs value for the input parameters because,
by default, they should only set the rx-usecs value.
This patch also adds the helper function to get the
previous rx coalesce value similar to tx coalesce.
How to test:
User can get the coalesce value using ethtool command.
Example command:
Get: ethtool -c <interface>
Previous output:
rx-usecs: 3
rx-frames: n/a
rx-usecs-irq: n/a
rx-frames-irq: n/a
tx-usecs: 0
tx-frames: n/a
tx-usecs-irq: n/a
tx-frames-irq: n/a
New output:
rx-usecs: 3
rx-frames: n/a
rx-usecs-irq: n/a
rx-frames-irq: n/a
tx-usecs: 3
tx-frames: n/a
tx-usecs-irq: n/a
tx-frames-irq: n/a
Fixes: 8c5ad0dae9 ("igc: Add ethtool support")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230919170331.1581031-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When an XDP redirect happens before the link is ready, that
transmission will not finish and will timeout, causing an adapter
reset. If the redirects do not stop, the adapter will not stop
resetting.
Wait for the driver to signal that there's a carrier before allowing
transmissions to proceed.
Previous code was relying that when __IGC_DOWN is cleared, the NIC is
ready to transmit as all the queues are ready, what happens is that
the carrier presence will only be signaled later, after the watchdog
workqueue has a chance to run. And during this interval (between
clearing __IGC_DOWN and the watchdog running) if any transmission
happens the timeout is emitted (detected by igc_tx_timeout()) which
causes the reset, with the potential for the infinite loop.
Fixes: 4ff3203610 ("igc: Add support for XDP_REDIRECT action")
Reported-by: Ferenc Fejes <ferenc.fejes@ericsson.com>
Closes: https://lore.kernel.org/netdev/0caf33cf6adb3a5bf137eeaa20e89b167c9986d5.camel@ericsson.com/
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Ferenc Fejes <ferenc.fejes@ericsson.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the minimum value of RX/TX descriptors to 64 to enable setting the rx/tx
value between 64 and 80. All igc devices can use as low as 64 descriptors.
This change will unify igc with other drivers.
Based on commit 7b1be1987c ("e1000e: lower ring minimum size to 64")
Fixes: 0507ef8a03 ("igc: Add transmit and receive fastpath and interrupt handlers")
Signed-off-by: Olga Zaborska <olga.zaborska@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With the 10us interval, we were seeing PTM transactions take around 12us.
Hardware team suggested this interval could be lowered to 1us which was
confirmed with PCIe sniffer. With the 1us interval, PTM dialogs took
around 2us.
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The IGC_PTM_CTRL_SHRT_CYC defines the time between two consecutive PTM
requests. The bit resolution of this field is six bits. That bit five was
missing in the mask. This patch comes to correct the typo in the
IGC_PTM_CTRL_SHRT_CYC macro.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://lore.kernel.org/r/20230821171721.2203572-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Access to shared variables through hrtimer requires locking in order
to protect the variables because actions to write into these variables
(oper_gate_closed, admin_gate_closed, and qbv_transition) might potentially
occur simultaneously. This patch provides a locking mechanisms to avoid
such scenarios.
Fixes: 175c241288 ("igc: Fix TX Hang issue when QBV Gate is closed")
Suggested-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230807205129.3129346-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRdM/uy1Ege0+EN1fNar9k/UBDW4wUCZMvevwAKCRBar9k/UBDW
42Z0AP90hLZ9OmoghYAlALHLl8zqXuHCV8OeFXR5auqG+kkcCwEAx6h99vnh4zgP
Tngj6Yid60o39/IZXXblhV37HfSiyQ8=
=/kVE
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Martin KaFai Lau says:
====================
pull-request: bpf-next 2023-08-03
We've added 54 non-merge commits during the last 10 day(s) which contain
a total of 84 files changed, 4026 insertions(+), 562 deletions(-).
The main changes are:
1) Add SO_REUSEPORT support for TC bpf_sk_assign from Lorenz Bauer,
Daniel Borkmann
2) Support new insns from cpu v4 from Yonghong Song
3) Non-atomically allocate freelist during prefill from YiFei Zhu
4) Support defragmenting IPv(4|6) packets in BPF from Daniel Xu
5) Add tracepoint to xdp attaching failure from Leon Hwang
6) struct netdev_rx_queue and xdp.h reshuffling to reduce
rebuild time from Jakub Kicinski
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (54 commits)
net: invert the netdevice.h vs xdp.h dependency
net: move struct netdev_rx_queue out of netdevice.h
eth: add missing xdp.h includes in drivers
selftests/bpf: Add testcase for xdp attaching failure tracepoint
bpf, xdp: Add tracepoint to xdp attaching failure
selftests/bpf: fix static assert compilation issue for test_cls_*.c
bpf: fix bpf_probe_read_kernel prototype mismatch
riscv, bpf: Adapt bpf trampoline to optimized riscv ftrace framework
libbpf: fix typos in Makefile
tracing: bpf: use struct trace_entry in struct syscall_tp_t
bpf, devmap: Remove unused dtab field from bpf_dtab_netdev
bpf, cpumap: Remove unused cmap field from bpf_cpu_map_entry
netfilter: bpf: Only define get_proto_defrag_hook() if necessary
bpf: Fix an array-index-out-of-bounds issue in disasm.c
net: remove duplicate INDIRECT_CALLABLE_DECLARE of udp[6]_ehashfn
docs/bpf: Fix malformed documentation
bpf: selftests: Add defrag selftests
bpf: selftests: Support custom type and proto for client sockets
bpf: selftests: Support not connecting client socket
netfilter: bpf: Support BPF_F_NETFILTER_IP_DEFRAG in netfilter link
...
====================
Link: https://lore.kernel.org/r/20230803174845.825419-1-martin.lau@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Handful of drivers currently expect to get xdp.h by virtue
of including netdevice.h. This will soon no longer be the case
so add explicit includes.
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230803010230.1755386-2-kuba@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
In normal operation, each populated queue item has
next_to_watch pointing to the last TX desc of the packet,
while each cleaned item has it set to 0. In particular,
next_to_use that points to the next (necessarily clean)
item to use has next_to_watch set to 0.
When the TX queue is used both by an application using
AF_XDP with ZEROCOPY as well as a second non-XDP application
generating high traffic, the queue pointers can get in
an invalid state where next_to_use points to an item
where next_to_watch is NOT set to 0.
However, the implementation assumes at several places
that this is never the case, so if it does hold,
bad things happen. In particular, within the loop inside
of igc_clean_tx_irq(), next_to_clean can overtake next_to_use.
Finally, this prevents any further transmission via
this queue and it never gets unblocked or signaled.
Secondly, if the queue is in this garbled state,
the inner loop of igc_clean_tx_ring() will never terminate,
completely hogging a CPU core.
The reason is that igc_xdp_xmit_zc() reads next_to_use
before acquiring the lock, and writing it back
(potentially unmodified) later. If it got modified
before locking, the outdated next_to_use is written
pointing to an item that was already used elsewhere
(and thus next_to_watch got written).
Fixes: 9acf59a752 ("igc: Enable TX via AF_XDP zero-copy")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230717175444.3217831-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add TransmissionOverrun as per defined by IEEE 802.1Q Bridges.
TransmissionOverrun counter shall be incremented if the implementation
detects that a frame from a given queue is still being transmitted by
the MAC when that gate-close event for that queue occurs.
This counter is utilised by the Certification conformance test to
inform the user application whether any packets are currently being
transmitted on a particular queue during a gate-close event.
Intel Discrete I225/I226 have a mechanism to not transmit a packets if
the gate open time is insufficient for the packet transmission by setting
the Strict_End bit. Thus, it is expected for this counter to be always
zero at this moment.
Inspired from enetc_taprio_stats() and enetc_taprio_queue_stats(), now
driver also report the tx_overruns counter per traffic class.
User can get this counter by using below command:
1) tc -s qdisc show dev <interface> root
2) tc -s class show dev <interface>
Test Result (Before):
class mq :1 root
Sent 1289 bytes 20 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
class mq :2 root
Sent 124 bytes 2 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
class mq :3 root
Sent 46028 bytes 86 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
class mq :4 root
Sent 2596 bytes 14 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Test Result (After):
class taprio 100:1 root
Sent 8491 bytes 38 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Transmit overruns: 0
class taprio 100:2 root
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Transmit overruns: 0
class taprio 100:3 root
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Transmit overruns: 0
class taprio 100:4 root
Sent 994 bytes 11 pkt (dropped 0, overlimits 0 requeues 1)
backlog 0b 0p requeues 1
Transmit overruns: 0
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230714201428.1718097-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The insertion of an empty frame was introduced with
commit db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
in order to ensure that the current cycle has at least one packet if
there is some packet to be scheduled for the next cycle.
However, the current implementation does not properly check if
a packet is already scheduled for the current cycle. Currently,
an empty packet is always inserted if and only if
txtime >= end_of_cycle && txtime > last_tx_cycle
but since last_tx_cycle is always either the end of the current
cycle (end_of_cycle) or the end of a previous cycle, the
second part (txtime > last_tx_cycle) is always true unless
txtime == last_tx_cycle.
What actually needs to be checked here is if the last_tx_cycle
was already written within the current cycle, so an empty frame
should only be inserted if and only if
txtime >= end_of_cycle && end_of_cycle > last_tx_cycle.
This patch does not only avoid an unnecessary insertion, but it
can actually be harmful to insert an empty packet if packets
are already scheduled in the current cycle, because it can lead
to a situation where the empty packet is actually processed
as the first packet in the upcoming cycle shifting the packet
with the first_flag even one cycle into the future, finally leading
to a TX hang.
The TX hang can be reproduced on a i225 with:
sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x1 \
txtime-delay 500000 \
clockid CLOCK_TAI
sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload \
skip_sock_check
and traffic generator
sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns
with traffic.cfg
#define ETH_P_IP 0x0800
{
/* Ethernet Header */
0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed
0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 48, 1, # IP Src - adapt as needed
10, 0, 48, 10, # IP Dest - adapt as needed
const16(5555), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
and the observed message with that is for example
igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
Tx Queue <0>
TDH <32>
TDT <3c>
next_to_use <3c>
next_to_clean <32>
buffer_info[next_to_clean]
time_stamp <ffff26a8>
next_to_watch <00000000632a1828>
jiffies <ffff27f8>
desc.status <1048000>
Fixes: db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is possible (verified on a running system) that frames are processed
by igc_tx_launchtime with a txtime before the start of the cycle
(baset_est).
However, the result of txtime - baset_est is written into a u32,
leading to a wrap around to a positive number. The following
launchtime > 0 check will only branch to executing launchtime = 0
if launchtime is already 0.
Fix it by using a s32 before checking launchtime > 0.
Fixes: db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The flags IGC_TXQCTL_STRICT_CYCLE and IGC_TXQCTL_STRICT_END
prevent the packet transmission over slot and cycle boundaries.
This is important for taprio offload where the slots and
cycles correspond to the slots and cycles configured for the
network.
However, the Qbv offload feature of the i225 is also used for
enabling TX launchtime / ETF offload. In that case, however,
the cycle has no meaning for the network and is only used
internally to adapt the base time register after a second has
passed.
Enabling strict mode in this case would unnecessarily prevent
the transmission of certain packets (i.e. at the boundary of a
second) and thus interferes with the ETF qdisc that promises
transmission at a certain point in time.
Similar to ETF, this also applies to CBS offload that also should
not be influenced by strict mode unless taprio offload would be
enabled at the same time.
This fully reverts
commit d8f45be01d ("igc: Use strict cycles for Qbv scheduling")
but its commit message only describes what was already implemented
before that commit. The difference to a plain revert of that commit
is that it now copes with the base_time = 0 case that was fixed with
commit e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
In particular, enabling strict mode leads to TX hang situations
under high traffic if taprio is applied WITHOUT taprio offload
but WITH ETF offload, e.g. as in
sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x1 \
txtime-delay 500000 \
clockid CLOCK_TAI
sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload \
skip_sock_check
and traffic generator
sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns
with traffic.cfg
#define ETH_P_IP 0x0800
{
/* Ethernet Header */
0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed
0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 48, 1, # IP Src - adapt as needed
10, 0, 48, 10, # IP Dest - adapt as needed
const16(5555), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
and the observed message with that is for example
igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
Tx Queue <0>
TDH <d0>
TDT <f0>
next_to_use <f0>
next_to_clean <d0>
buffer_info[next_to_clean]
time_stamp <ffff661f>
next_to_watch <00000000245a4efb>
jiffies <ffff6e48>
desc.status <1048000>
Fixes: d8f45be01d ("igc: Use strict cycles for Qbv scheduling")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since commit e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
it is possible to enable taprio offload with a basetime of 0.
However, the check if taprio offload is already enabled (and thus -EALREADY
should be returned for igc_save_qbv_schedule) still relied on
adapter->base_time > 0.
This can be reproduced as follows:
# TAPRIO offload (flags == 0x2) and base-time = 0
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x2
# The second call should fail with "Error: Device failed to setup taprio offload."
# But that only happens if base-time was != 0
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x2
Fixes: e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Only set adapter->taprio_offload_enable after validating the arguments.
Otherwise, it stays set even if the offload was not enabled.
Since the subsequent code does not get executed in case of invalid
arguments, it will not be read at first.
However, by activating and then deactivating another offload
(e.g. ETF/TX launchtime offload), taprio_offload_enable is read
and erroneously keeps the offload feature of the NIC enabled.
This can be reproduced as follows:
# TAPRIO offload (flags == 0x2) and negative base-time leading to expected -ERANGE
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time -1000 \
sched-entry S 01 300000 \
flags 0x2
# IGC_TQAVCTRL is 0x0 as expected (iomem=relaxed for reading register)
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
# Activate ETF offload
sudo tc qdisc replace dev enp1s0 parent root handle 6666 mqprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
hw 0
sudo tc qdisc add dev enp1s0 parent 6666:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload
# IGC_TQAVCTRL is 0x9 as expected
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
# Deactivate ETF offload again
sudo tc qdisc delete dev enp1s0 parent 6666:1
# IGC_TQAVCTRL should now be 0x0 again, but is observed as 0x9
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
Fixes: e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the current implementation the flags adapter->qbv_enable
and IGC_FLAG_TSN_QBV_ENABLED have a similar name, but do not
have the same meaning. The first one is used only to indicate
taprio offload (i.e. when igc_save_qbv_schedule was called),
while the second one corresponds to the Qbv mode of the hardware.
However, the second one is also used to support the TX launchtime
feature, i.e. ETF qdisc offload. This leads to situations where
adapter->qbv_enable is false, but the flag IGC_FLAG_TSN_QBV_ENABLED
is set. This is prone to confusion.
The rename should reduce this confusion. Since it is a pure
rename, it has no impact on functionality.
Fixes: e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
I225/6 hardware can be programmed to start PPS output once
the time in Target Time registers is reached. The time
programmed in these registers should always be into future.
Only then PPS output is triggered when SYSTIM register
reaches the programmed value. There are two modes in i225/6
hardware to program PPS, pulse and clock mode.
There were issues reported where PPS is not generated when
start time is in past.
Example 1, "echo 0 0 0 2 0 > /sys/class/ptp/ptp0/period"
In the current implementation, a value of '0' is programmed
into Target time registers and PPS output is in pulse mode.
Eventually an interrupt which is triggered upon SYSTIM
register reaching Target time is not fired. Thus no PPS
output is generated.
Example 2, "echo 0 0 0 1 0 > /sys/class/ptp/ptp0/period"
Above case, a value of '0' is programmed into Target time
registers and PPS output is in clock mode. Here, HW tries to
catch-up the current time by incrementing Target Time
register. This catch-up time seem to vary according to
programmed PPS period time as per the HW design. In my
experiments, the delay ranged between few tens of seconds to
few minutes. The PPS output is only generated after the
Target time register reaches current time.
In my experiments, I also observed PPS stopped working with
below test and could not recover until module is removed and
loaded again.
1) echo 0 <future time> 0 1 0 > /sys/class/ptp/ptp1/period
2) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period
3) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period
After this PPS did not work even if i re-program with proper
values. I could only get this back working by reloading the
driver.
This patch takes care of calculating and programming
appropriate future time value into Target Time registers.
Fixes: 5e91c72e56 ("igc: Fix PPS delta between two synchronized end-points")
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
