The 'igc_check_downshift' method always returns 0; there is no need
for a return value so change the type of this method to void.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Complete to commit 8e153faf58 ("igc: Remove unused phy type")
i225 parts have only one PHY. There is no point to use phy_type enum.
Clean up the code accordingly, and get rid of the unused enum lines.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
igc_set_spd_dplx method is not used. This patch comes to tidy up
the driver code.
Reported-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some mainboard/CPU combinations, in particular, Alder Lake-S with a
W680 mainboard, have shown problems (system hangs usually, no kernel
logs) with suspend/resume when PCIe PTM is enabled and active. In some
cases, it could be reproduced when removing the igc module.
The best we can do is to stop PTM dialogs from the downstream/device
side before the interface is brought down. PCIe PTM will be re-enabled
when the interface is being brought up.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
An infinite loop may occur if we fail to acquire the HW semaphore,
which is needed for resource release.
This will typically happen if the hardware is surprise-removed.
At this stage there is nothing to do, except log an error and quit.
Fixes: c0071c7aa5 ("igc: Add HW initialization code")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Similar to "igc_read_phy_reg_gpy: drop premature return" patch.
igc_write_phy_reg_gpy checks the return value from igc_write_phy_reg_mdic
and if it's not 0, returns immediately. By doing this, it leaves the HW
semaphore in the acquired state.
Drop this premature return statement, the function returns after
releasing the semaphore immediately anyway.
Fixes: 5586838fe9 ("igc: Add code for PHY support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reported-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
igc_read_phy_reg_gpy checks the return value from igc_read_phy_reg_mdic
and if it's not 0, returns immediately. By doing this, it leaves the HW
semaphore in the acquired state.
Drop this premature return statement, the function returns after
releasing the semaphore immediately anyway.
Fixes: 5586838fe9 ("igc: Add code for PHY support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, igc_construct_skb_zc() currently allocates and reserves
additional `xdp->data_meta - xdp->data_hard_start`, which is about
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only (+ meta) to
__napi_alloc_skb() and don't reserve anything. This will give
enough headroom for stack processing.
Also, net_prefetch() xdp->data_meta and align the copy size to
speed-up memcpy() a little and better match igc_construct_skb().
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be
1.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
Time synchronization was not properly enabled on non-MSI-X platforms.
Fixes: 2c344ae245 ("igc: Add support for TX timestamping")
Signed-off-by: James McLaughlin <james.mclaughlin@qsc.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It was reported that when PCIe PTM is enabled, some lockups could
be observed with some integrated i225-V models.
While the issue is investigated, we can disable crosstimestamp for
those models and see no loss of functionality, because those models
don't have any support for time synchronization.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Link: https://lore.kernel.org/all/924175a188159f4e03bd69908a91e606b574139b.camel@gmx.de/
Reported-by: Stefan Dietrich <roots@gmx.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
igc driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
'MII_CR_FULL_DUPLEX' define not in use. This patch comes to tidy up
obsolete define.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
'IGC_CTRL_EXT_LINK_MODE_MASK' not in use. This patch comes to tidy up
obsolete define.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices use only spi nvm type. This patch comes to tidy up
obsolete nvm types.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
_phy_none type not in use. Clean up the code accordingly,
and get rid of the unused enum line
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
_I_PHY_ID not in use. Clean up the code accordingly,
and get rid of the unused define
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.
Fixes: 707abf0695 ("igc: Add initial LTR support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In non trivial scenarios, the action id alone is not sufficient to
identify the program causing the warning. Before the previous patch,
the generated stack-trace pointed out at least the involved device
driver.
Let's additionally include the program name and id, and the relevant
device name.
If the user needs additional infos, he can fetch them via a kernel
probe, leveraging the arguments added here.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/ddb96bb975cbfddb1546cf5da60e77d5100b533c.1638189075.git.pabeni@redhat.com
Enabling the XDP bpf_prog access to data_meta area is a very small
change. Hint passing 'true' to xdp_prepare_buff().
The SKB layers can also access data_meta area, which required more
driver changes to support. Reviewers, notice the igc driver have two
different functions that can create SKBs, depending on driver config.
Hint for testers, ethtool priv-flags legacy-rx enables
the function igc_construct_skb()
ethtool --set-priv-flags DEV legacy-rx on
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Driver already implicitly supports XDP metadata access in AF_XDP
zero-copy mode, as xsk_buff_pool's xp_alloc() naturally set xdp_buff
data_meta equal data.
This works fine for XDP and AF_XDP, but if a BPF-prog adjust via
bpf_xdp_adjust_meta() and choose to call XDP_PASS, then igc function
igc_construct_skb_zc() will construct an invalid SKB packet. The
function correctly include the xdp->data_meta area in the memcpy, but
forgot to pull header to take metasize into account.
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The _reset_hw_base method switched from port reset (CTRL[26]) to device
reset (CTRL[29]) since the FW was receiving an interrupt on CTRL[29].
FW code was later modified to also receive an interrupt on CTRL[26].
Since certain HW values are not reset to default by CTRL[29], we go back
to CTRL[26] for the HW reset, as it meets all current requirements.
This reverts commit bb4265ec24 ("igc: Update the MAC reset flow").
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new device ID for the next step of the silicon and
reflect the I226_LMVP part.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices only have copper phy media type. There is no point in
checking phy media type during the phy initialization. This patch cleans
up a pointless check.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The device ID for I226_K was incorrectly assigned, update the device
ID to the correct one.
Fixes: bfa5e98c9d ("igc: Add new device ID")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
On a UML build, the igc_ptp driver uses CONFIG_X86_TSC for timestamp
conversion. The function that is used is not available on UML builds,
so have the function use the default system_counterval_t timestamp
instead for UML builds.
Prevents this build error on UML:
../drivers/net/ethernet/intel/igc/igc_ptp.c: In function ‘igc_device_tstamp_to_system’:
../drivers/net/ethernet/intel/igc/igc_ptp.c:777:9: error: implicit declaration of function ‘convert_art_ns_to_tsc’ [-Werror=implicit-function-declaration]
return convert_art_ns_to_tsc(tstamp);
../drivers/net/ethernet/intel/igc/igc_ptp.c:777:9: error: incompatible types when returning type ‘int’ but ‘struct system_counterval_t’ was expected
return convert_art_ns_to_tsc(tstamp);
Fixes: 68f5d3f3b6 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-um@lists.infradead.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Link: https://lore.kernel.org/r/20211014050516.6846-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
- cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking tunnel offloading, it turns out that offloading doesn't work
as expected. The following script allows to reproduce the issue.
Call it as `testscript DEVICE LOCALIP REMOTEIP NETMASK'
=== SNIP ===
if [ $# -ne 4 ]
then
echo "Usage $0 DEVICE LOCALIP REMOTEIP NETMASK"
exit 1
fi
DEVICE="$1"
LOCAL_ADDRESS="$2"
REMOTE_ADDRESS="$3"
NWMASK="$4"
echo "Driver: $(ethtool -i ${DEVICE} | awk '/^driver:/{print $2}') "
ethtool -k "${DEVICE}" | grep tx-udp
echo
echo "Set up NIC and tunnel..."
ip addr add "${LOCAL_ADDRESS}/${NWMASK}" dev "${DEVICE}"
ip link set "${DEVICE}" up
sleep 2
ip link add vxlan1 type vxlan id 42 \
remote "${REMOTE_ADDRESS}" \
local "${LOCAL_ADDRESS}" \
dstport 0 \
dev "${DEVICE}"
ip addr add fc00::1/64 dev vxlan1
ip link set vxlan1 up
sleep 2
rm -f vxlan.pcap
echo "Running tcpdump and iperf3..."
( nohup tcpdump -i any -w vxlan.pcap >/dev/null 2>&1 ) &
sleep 2
iperf3 -c fc00::2 >/dev/null
pkill tcpdump
echo
echo -n "Max. Paket Size: "
tcpdump -r vxlan.pcap -nnle 2>/dev/null \
| grep "${LOCAL_ADDRESS}.*> ${REMOTE_ADDRESS}.*OTV" \
| awk '{print $8}' | awk -F ':' '{print $1}' \
| sort -n | tail -1
echo
ip link del vxlan1
ip addr del ${LOCAL_ADDRESS}/${NWMASK} dev "${DEVICE}"
=== SNAP ===
The expected outcome is
Max. Paket Size: 64904
This is what you see on igb, the code igc has been taken from.
However, on igc the output is
Max. Paket Size: 1516
so the GSO aggregate packets are segmented by the kernel before calling
igc_xmit_frame. Inside the subsequent call to igc_tso, the check for
skb_is_gso(skb) fails and the function returns prematurely.
It turns out that this occurs because the feature flags aren't set
entirely correctly in igc_probe. In contrast to the original code
from igb_probe, igc_probe neglects to set the flags required to allow
tunnel offloading.
Setting the same flags as igb fixes the issue on igc.
Fixes: 34428dff36 ("igc: Add GSO partial support")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for Credit-based shaper(CBS) Qdisc hardware
offload mode in the driver. There are two sets of IEEE802.1Qav
(CBS) HW logic in i225 controller and this patch supports
enabling them in the top two priority TX queues.
Driver implemented as recommended by Foxville External
Architecture Specification v0.993. Idleslope and Hi-credit are
the CBS tunable parameters for i225 NIC, programmed in TQAVCC
and TQAVHC registers respectively.
In-order for IEEE802.1Qav (CBS) algorithm to work as intended
and provide BW reservation CBS should be enabled in highest
priority queue first. If we enable CBS on any of low priority
queues, the traffic in high priority queue does not allow low
priority queue to be selected for transmission and bandwidth
reservation is not guaranteed.
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Signed-off-by: Mallikarjuna Chilakala <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Separates the procedure done during reset from applying a
configuration, knowing when the code is executing allow us to
separate the better what changes the hardware state from what
changes only the driver state.
Introduces a flag for bookkeeping the driver state of TSN
features. When Qav and frame-preemption is also implemented
this flag makes it easier to keep track on whether a TSN feature
driver state is enabled or not though controller state changes,
say, during a reset.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Signed-off-by: Mallikarjuna Chilakala <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Sets default values for each queue cycle start and cycle end.
This allows some simplification in the handling of these
configurations as most TSN features in i225 require a cycle
to be configured.
In i225, cycle start and end time is required to be programmed
for CBS to work properly.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Signed-off-by: Mallikarjuna Chilakala <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enables PCIe PTM (Precision Time Measurement) support in the igc
driver. Notifies the PCI devices that PCIe PTM should be enabled.
PCIe PTM is similar protocol to PTP (Precision Time Protocol) running
in the PCIe fabric, it allows devices to report time measurements from
their internal clocks and the correlation with the PCIe root clock.
The i225 NIC exposes some registers that expose those time
measurements, those registers will be used, in later patches, to
implement the PTP_SYS_OFFSET_PRECISE ioctl().
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use num_tx_queues rather than the IGC_MAX_TX_QUEUES fixed number 4 when
iterating over tx_ring queue since instantiated queue count could be
less than 4 where on-line cpu count is less than 4.
Fixes: ec50a9d437 ("igc: Add support for taprio offloading")
Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After unplug thunderbolt dock with i225, pciehp interrupt is triggered,
remove call will read/write mmio address which is already disconnected,
then cause page fault and make system hang.
Check PCI state to remove device safely.
Trace:
BUG: unable to handle page fault for address: 000000000000b604
Oops: 0000 [#1] SMP NOPTI
RIP: 0010:igc_rd32+0x1c/0x90 [igc]
Call Trace:
igc_ptp_suspend+0x6c/0xa0 [igc]
igc_ptp_stop+0x12/0x50 [igc]
igc_remove+0x7f/0x1c0 [igc]
pci_device_remove+0x3e/0xb0
__device_release_driver+0x181/0x240
Fixes: 13b5b7fd6a ("igc: Add support for Tx/Rx rings")
Fixes: b03c49cde6 ("igc: Save PTP time before a reset")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the cycle time is set to maximum of 1s, the TX Hang timeout need to
be increase to avoid possible TX Hang.
There is no dedicated number specific in data sheet for the timeout factor.
Timeout factor was determined during the debugging to solve the "Tx Hang"
issues that happen in some cases mainly during ETF(Earliest TxTime First).
This can be test by using TSN Schedule Tx Tools udp_tai sample application.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
According to datasheet section 8.12.19, when there's no TSN offloading
Shadow_QbvCycle bit[29:0] must be set to zero for basic scheduling.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
