The support for xHCI controllers with only one roothub, and the code
to defer primary roothub registation until second roothub got merged
to usb-next for 5.19 at the same time.
commit 873f323618 ("xhci: prepare for operation w/o shared hcd")
commit b7a4f9b5d0 ("xhci: Set HCD flag to defer primary roothub
registration")
These got merged in such a way that the flag to defer primary roothub
registration is set even for xHC controllers with just one roothub.
Fix this by setting the defer flag in a codepath taken only if we have
two roothubs
Fixes: 873f323618 ("xhci: prepare for operation w/o shared hcd")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220516094850.19788-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't enable U1 or U2 Link powermanagenet (LPM) states for USB3
devices connected to tier 2 or further hubs.
For unknown reasons we previously only prevented U1.
Be consistent, and prevent both U1/U2 states if tier policy doesn't
allow LPM.
Also check the tier policy a bit earlier, and return if U1/U2 is
not allowed. This avoids unnecessary xhci MEL commands.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'stop endpoint' command timer was started when a 'stop endpoint'
command was added to the command queue.
This can trigger unwanted timeouts if there are several pending commands
in the queue that xHC needs to handle first.
The generic command timer, which was added later than the 'stop endpoint'
timeout timer, times each command currently being handled by xHC hardware.
A timed out stop endpoint command was treated as a more severe issue than
other failed commands, so the separate stop endpoint timer was left
unchanged.
Use the generic command timer for stop endpoint commands. Identify if
the timed out command was a stop endpoint command in the generic handler,
and treat it with the same severity as earlier.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares xhci for the following scenario:
- If either of the root hubs has no ports, then omit shared hcd
- Main hcd can be USB3 if there are no USB2 ports
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factoring out parts of xhci_gen_setup() has two motivations:
- When adding functionaliy to omit shared hcd if not needed in a
subsequent patch, we'll have to call xhci_hcd_init_usb3_data()
from two places.
- It reduces size of xhci_gen_setup() and makes it better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer
registering primary roothub in usb_add_hcd() if xhci has two roothubs.
This will make sure both primary roothub and secondary roothub will be
registered along with the second HCD.
This is required for cold plugged USB devices to be detected in certain
PCIe USB cards (like Inateck USB card connected to AM64 EVM or J7200 EVM).
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26 ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2 ("usb: hub: Fix usb enumeration issue due to address0
race")
[minor rebase change, and commit message update -Mathias]
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-3-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While rebooting, XHCI controller and its bus device will be shut down
in order by .shutdown callback. Stopping roothubs polling in
xhci_shutdown() can prevent XHCI driver from accessing port status
after its bus device shutdown.
Take PCIe XHCI controller as example, if XHCI driver doesn't stop roothubs
polling, XHCI driver may access PCIe BAR register for port status after
parent PCIe root port driver is shutdown and cause PCIe bus error.
[check shared hcd exist before stopping its roothub polling -Mathias]
Cc: stable@vger.kernel.org
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ret/retval will be set when it used, no need to init at definition.
[modified subject line -Mathias]
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to store temperary value in hcc_params.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_reset() timeout was increased from 250ms to 10 seconds in order to
give Renesas 720201 xHC enough time to get ready in probe.
xhci_reset() is called with interrupts disabled in other places, and
waiting for 10 seconds there is not acceptable.
Add a timeout parameter to xhci_reset(), and adjust it back to 250ms
when called from xhci_stop() or xhci_shutdown() where interrupts are
disabled, and successful reset isn't that critical.
This solves issues when deactivating host mode on platforms like SM8450.
For now don't change the timeout if xHC is reset in xhci_resume().
No issues are reported for it, and we need the reset to succeed.
Locking around that reset needs to be revisited later.
Additionally change the signed integer timeout parameter in
xhci_handshake() to a u64 to match the timeout value we pass to
readl_poll_timeout_atomic()
Fixes: 22ceac1912 ("xhci: Increase reset timeout for Renesas 720201 host.")
Cc: stable@vger.kernel.org
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reported-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here, and it resolves a merge conflict in:
drivers/usb/dwc3/dwc3-pci.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xhci_endpoint_{disable|reset}() the expression '&vdev->eps[ep_index]'
just cannot be NULL, so the checks have no sense at all...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every lpm commmand, both for USB 2 and USB 3 devies used the same
xhci->lpm_command structure to change max exit latency.
xhci->lpm_command is only protected by a hcd->bandwidth mutex, which is
not enoungh as USB 2 and USB 3 devices are behind separate HCDs.
Simplify code and avoid unnecessary locking risks by allocating
separate command structures for each lpm command, just like with
all other commands.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current workaround to call the dbc_tty_init() in probe is
not working in case we have several xhci devices with dbc enabled.
dbc_tty_init() should be called only once by a module init call when
module is loaded.
until dbgtty is its own module call dbc_tty_init() from xhci
module init call.
Same is true for unloading and dbc_tty_exit()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These names give the impression the functions are related to
module init calls, but are in fact creating and removing the dbc
fake device
Rename them to xhci_create_dbc_dev() and xhci_remove_dbc_dev().
We will need the _init and _exit names for actual dbc module init
and exit calls.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The -ENODEV return value from xhci_check_args() is incorrectly changed
to -EINVAL in a couple places before propagated further.
xhci_check_args() returns 4 types of value, -ENODEV, -EINVAL, 1 and 0.
xhci_urb_enqueue and xhci_check_streams_endpoint return -EINVAL if
the return value of xhci_check_args <= 0.
This causes problems for example r8152_submit_rx, calling usb_submit_urb
in drivers/net/usb/r8152.c.
r8152_submit_rx will never get -ENODEV after submiting an urb when xHC
is halted because xhci_urb_enqueue returns -EINVAL in the very beginning.
[commit message and header edit -Mathias]
Fixes: 203a86613f ("xhci: Avoid NULL pointer deref when host dies.")
Cc: stable@vger.kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When HCE(Host Controller Error) is set, it means an internal
error condition has been detected. Software needs to re-initialize
the HC, so add this check in xhci resume.
Cc: stable@vger.kernel.org
Signed-off-by: Puma Hsu <pumahsu@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.
Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.
This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.
usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer
registering primary roothub in usb_add_hcd(). This will make sure both
primary roothub and secondary roothub will be registered along with the
second HCD. This is required for cold plugged USB devices to be detected
in certain PCIe USB cards (like Inateck USB card connected to AM64 EVM
or J7200 EVM).
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-3-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we register two usb buses for each xHC, and systems with several
hosts are more and more common it is getting hard to follow the
flow of debug messages without knowing which bus they belong to
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5d5323a6f3.
That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.
Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2
After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.
Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.
exit latency calculations have been revised since then
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The continue statement at the end of a for-loop has no effect,
remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Continue has no effect")
Cc: Mathias Nyman <mathias.nyman@intel.com>
Link: https://lore.kernel.org/r/20210618090447.99114-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the urb->actual_length to bytes successfully copied in case all bytes
weren't copied from a temporary buffer to the URB sg list.
Also print a debug message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be
submitted in interrupt context" (see comment related to 'usb_submit_urb()'
in 'drivers/usb/core/urb.c')
So this flag should be used in all the calling chain.
Up to now, 'xhci_check_maxpacket()' which is only called from
'xhci_urb_enqueue()', uses GFP_KERNEL.
Be safe and pass the mem_flags to this function as well.
Fixes: ddba5cd0ae ("xhci: Use command structures when queuing commands on the command ring")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Max Interrupters supported by the controller is given in a 10bit
wide bitfield, but the driver uses a fixed 128 size array to index these
interrupters.
Klockwork reports a possible array out of bounds case which in theory
is possible. In practice this hasn't been hit as a common number of Max
Interrupters for new controllers is 8, not even close to 128.
This needs to be fixed anyway
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210406070208.3406266-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If port terminations are detected in suspend, but link never reaches U0
then xHCI may have an internal uncleared wake state that will cause an
immediate wake after suspend.
This wake state is normally cleared when driver clears the PORT_CSC bit,
which is set after a device is enabled and in U0.
Write 1 to clear PORT_CSC for ports that don't have anything connected
when suspending. This makes sure any pending internal wake states in
xHCI are cleared.
Cc: stable@vger.kernel.org
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A xHC USB 3 port might miss the first wake signal from a USB 3 device
if the port LFPS reveiver isn't enabled fast enough after xHC resume.
xHC host will anyway be resumed by a PME# signal, but will go back to
suspend if no port activity is seen.
The device resends the U3 LFPS wake signal after a 100ms delay, but
by then host is already suspended, starting all over from the
beginning of this issue.
USB 3 specs say U3 wake LFPS signal is sent for max 10ms, then device
needs to delay 100ms before resending the wake.
Don't suspend immediately if port activity isn't detected in resume.
Instead add a retry. If there is no port activity then delay for 120ms,
and re-check for port activity.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently xhci-hcd.ko building depends on USB_XHCI_MTK, this
is not flexible for some cases. For example:
USB_XHCI_HCD is y, and USB_XHCI_MTK is m, then we can't
implement extended functions if only update xhci-mtk.ko
This patch is used to remove the dependence.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/0b62e21ddfacc1c2874726dd27ccab80c993f303.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't queue both a reset endpoint command and a
set TR deq command at once when handling a halted endpoint.
split this into two steps.
Initially only queue a reset endpoint command, and then if needed queue a
set TR deq command in the reset endpoint handler.
Note: This removes the RESET_EP_QUIRK handling which was added in
commit ac9d8fe7c6 ("USB: xhci: Add quirk for Fresco Logic xHCI hardware.")
This quirk was added in 2009 for prototype xHCI hardware meant for
evaluation purposes only, and should not reach consumers.
This hardware could not handle two commands queued at once, and had
bad data in the output context after a reset endpoint command.
After this patch two command are no longer queued at once, so that
part is solved in this rewrite, but the workaround for bad data in the
output context solved by issuing an extra configure endpoint command is
bluntly removed.
Adding this workaround to the new rewrite just adds complexity, and I
think it's time to let this quirk go.
Print a debug message instead.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci-mtk needs XHCI_MTK_HOST quirk functions in add_endpoint() and
drop_endpoint() to handle its own sw bandwidth management.
It stores bandwidth data into an internal table every time
add_endpoint() is called, and drops those in drop_endpoint().
But when bandwidth allocation fails at one endpoint, all earlier
allocation from the same interface could still remain at the table.
This patch moves bandwidth management codes to check_bandwidth() and
reset_bandwidth() path. To do so, this patch also adds those functions
to xhci_driver_overrides and lets mtk-xhci to release all failed
endpoints in reset_bandwidth() path.
Fixes: 08e469de87 ("usb: xhci-mtk: supports bandwidth scheduling with multi-TT")
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210113180444.v6.1.Id0d31b5f3ddf5e734d2ab11161ac5821921b1e1e@changeid
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit
latency is too long") was constraining the xhci code not to allow U1/U2
sleep states if the latency to wake up from the U-states reached the
service interval of an periodic endpoint. This fix was not taking into
account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time
will be calculated and configured differently.
It checks for u1_params.mel/u2_params.mel as a limit. But the code could
decide to write another MEL into the hardware. This leads to broken
cases where not enough bandwidth is available for other devices:
usb 1-2: can't set config #1, error -28
This patch is fixing that case by checking for timeout_ns after the
wakeup time was calculated depending on the quirks.
Fixes: 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit latency is too long")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Synopsys xHC has an internal TRB cache of size TRB_CACHE_SIZE for
each endpoint. The default value for TRB_CACHE_SIZE is 16 for SS and 8
for HS. The controller loads and updates the TRB cache from the transfer
ring in system memory whenever the driver issues a start transfer or
update transfer command.
For chained TRBs, the Synopsys xHC requires that the total amount of
bytes for all TRBs loaded in the TRB cache be greater than or equal to 1
MPS. Or the chain ends within the TRB cache (with a last TRB).
If this requirement is not met, the controller will not be able to send
or receive a packet and it will hang causing a driver timeout and error.
This can be a problem if a class driver queues SG requests with many
small-buffer entries. The XHCI driver will create a chained TRB for each
entry which may trigger this issue.
This patch adds logic to the XHCI driver to detect and prevent this from
happening.
For every (TRB_CACHE_SIZE - 2), we check the total buffer size of
the SG list and if the last window of (TRB_CACHE_SIZE - 2) SG list length
and we don't make up at least 1 MPS, we create a temporary buffer to
consolidate full SG list into the buffer.
We check at (TRB_CACHE_SIZE - 2) window because it is possible that there
would be a link and/or event data TRB that take up to 2 of the cache
entries.
We discovered this issue with devices on other platforms but have not
yet come across any device that triggers this on Linux. But it could be
a real problem now or in the future. All it takes is N number of small
chained TRBs. And other instances of the Synopsys IP may have smaller
values for the TRB_CACHE_SIZE which would exacerbate the problem.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Creating debugfs files while loding the spin_lock_irqsave(xhci->lock)
creates a lock dependecy that could possibly deadlock.
Lockdep warns:
=====================================================
WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
5.10.0-rc1pdx86+ #8 Not tainted
-----------------------------------------------------
systemd-udevd/386 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
ffffffffb1a94038 (pin_fs_lock){+.+.}-{2:2}, at: simple_pin_fs+0x22/0xa0
and this task is already holding:
ffff9e7b87fbc430 (&xhci->lock){-.-.}-{2:2}, at: xhci_alloc_streams+0x5f9/0x810
which would create a new lock dependency:
(&xhci->lock){-.-.}-{2:2} -> (pin_fs_lock){+.+.}-{2:2}
Create the files a bit later after lock is released.
Fixes: 673d746836 ("usb: xhci: add debugfs support for ep with stream")
CC: Li Jun <jun.li@nxp.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage of in_interrupt() in drivers is phased out for various reasons.
xhci_set_hc_event_deq() has an !in_interrupt() check which is pointless
because the function is only invoked from xhci_mem_init() which is clearly
task context as it does GFP_KERNEL allocations. Remove it.
xhci_urb_enqueue() prints a debug message if an URB is submitted after the
underlying hardware was suspended. But that warning is only issued when
in_interrupt() is true, which makes no sense. Simply return -ESHUTDOWN and
be done with it.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101110.148631116@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To show the trb ring of streams, use the exsiting ring files of bulk ep
to show trb ring of one specific stream ID, which stream ID's trb ring
will be shown, is controlled by a new debugfs file stream_id, this is to
avoid to create a large number of dir for every allocate stream IDs,
another debugfs file stream_context_array is created to show all the
allocated stream context array entries.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure xHC completes the configure endpoint command and xhci driver
sets the ring pointers correctly before we create the user readable
debugfs file.
In theory there was a small gap where a user could have read the
debugfs file and cause a NULL pointer dereference error as ring
pointer was not yet set, in practise we want this change to simplify
the upcoming streams debugfs support.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the xhci-plat.c is the platform driver, after the runtime pm is
enabled, the xhci_suspend is called if nothing is connected on
the port. When the system goes to suspend, it will call xhci_suspend again
if USB wakeup is enabled.
Since the runtime suspend wakeup setting is not always the same as
system suspend wakeup setting, eg, at runtime suspend we always need
wakeup if the controller is in low power mode; but at system suspend,
we may not need wakeup. So, we move the judgement after changing
wakeup setting.
[commit message rewording -Mathias]
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that:
- the usb gadget patch now does not break some systems, and
actually does what it was intended to do. Many thanks to
Marek Szyprowski for quickly noticing and testing the patch
from Andy Shevchenko to resolve this issue.
- some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the original pull request patches are all here, and
they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX0t32g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylFMACeLEQgeN1rmfQfLyo2NHROQEeDhnIAniLMhchZ
p9dXWJ8aNeyI5OrNjD5b
=Vd05
-----END PGP SIGNATURE-----
Merge tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that
the usb gadget patch now does not break some systems, and actually
does what it was intended to do. Many thanks to Marek Szyprowski for
quickly noticing and testing the patch from Andy Shevchenko to resolve
this issue.
Additionally, some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the patches are all here, and they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues"
* tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: storage: Add unusual_uas entry for Sony PSZ drives
USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge
usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()
USB: gadget: u_f: Unbreak offset calculation in VLAs
USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
USB: PHY: JZ4770: Fix static checker warning.
USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
USB: gadget: u_f: add overflow checks to VLA macros
xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed
xhci: Do warm-reset when both CAS and XDEV_RESUME are set
usb: host: xhci: fix ep context print mismatch in debugfs
usb: uas: Add quirk for PNY Pro Elite
tools: usb: move to tools buildsystem
USB: Fix device driver race
USB: Also match device drivers using the ->match vfunc
usb: host: xhci-tegra: fix tegra_xusb_get_phy()
usb: host: xhci-tegra: otg usb2/usb3 port init
usb: hcd: Fix use after free in usb_hcd_pci_remove()
usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()
...
Some device drivers call libusb_clear_halt when target ep queue
is not empty. (eg. spice client connected to qemu for usb redir)
Before commit f5249461b5 ("xhci: Clear the host side toggle
manually when endpoint is soft reset"), that works well.
But now, we got the error log:
EP not empty, refuse reset
xhci_endpoint_reset failed and left ep_state's EP_SOFT_CLEAR_TOGGLE
bit still set
So all the subsequent urb sumbits to the ep will fail with the
warn log:
Can't enqueue URB while manually clearing toggle
We need to clear ep_state EP_SOFT_CLEAR_TOGGLE bit after
xhci_endpoint_reset, even if it failed.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: stable <stable@vger.kernel.org> # v4.17+
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
