The hardware, depending on which part fails or times out,
returns 0xA5A5A5A. or 0x5A5A5A5. with the lowest 4 bits
encoding some further reason/status. However, mostly we
don't really need to care about the exact reasons, so
unify the checks for this to avoid hardcoding those magic
values all over the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230612184434.3e2959741a38.I1c297a53787b87e4e2b8f296c041921338573f4d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of upcoming things in both the stack and
drivers that would otherwise conflict, so merge wireless to
wireless-next to be able to avoid those conflicts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The DBGI dump is (unsurprisingly) of type DBGI, not SRAM.
This leads to bad register accesses because the union is
built differently, there's no allocation ID, and thus the
allocation ID ends up being 0x8000.
Note that this was already wrong for DRAM vs. SMEM since
they use different parts of the union, but the allocation
ID is at the same place, so it worked.
Fix all of this but set the allocation ID in a way that
the offset calculation ends up without any offset.
Fixes: 34bc27783a ("iwlwifi: yoyo: fix DBGI_SRAM ini dump header.")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.19a302ae4c65.I12272599f7c1930666157b9d5e7f81fe9ec4c421@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clang static analysis reports this representative issue
dbg.c:1455:6: warning: Branch condition evaluates to
a garbage value
if (!rxf_data.size)
^~~~~~~~~~~~~~
This check depends on iwl_ini_get_rxf_data() to clear
rxf_data but the function can return early without
doing the clear. So move the memset before the early
return.
Fixes: cc9b6012d3 ("iwlwifi: yoyo: use hweight_long instead of bit manipulating")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.872a7175f1ff.I33802a77a91998276992b088fbe25f61c87c33ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When NIC is in a bad state, reading data will return 28 bits as
0xa5a5a5a and the lowest 4 bits are not fixed value.
Mask these bits in a few places to skip the dump correctly.
Fixes: 89639e06d0 ("iwlwifi: yoyo: support for new DBGI_SRAM region")
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.df6c0663179d.I36d8487b2419c6fefa65e5514855d94327c3b1eb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Driver is using the dump name generated first time in all
generated dump in case of NMI.
The validity of dump name should be with each dump created
and need to reset after each use.
Fixes: 834f920ef3 ("wifi: iwlwifi: yoyo: Add driver defined dump file name")
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.6c987f820557.I924f2eae1eef2fe82c7a23be566551653d46f729@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Today in the code we have two options for collecting data sync/schedule,
the two options call the same function and can lead to racing in free
resources after done.
So we call only one of two sync/schedule, and in case of sync only
call sync function without also schedule to immediately run as a side
job.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220304131517.88574097ce1b.I1b42297619d638d677a2300ed9a95105c1262101@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Replace zero-length array with flexible-array member and make use
of the struct_size() helper in kzalloc().
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220216030841.1839666-1-chi.minghao@zte.com.cn
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Replace "struct list_head head = LIST_HEAD_INIT(head)" with
"LIST_HEAD(head)" to simplify the code.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/r/20220209032322.37472-1-cai.huoqing@linux.dev
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to preg protection we cannot write to this register
while FW is running (when FW in Halt it is ok).
since we have some cases that we need to dump this
region while FW is running remove this writing from DRV.
FW will do this writing.
Signed-off-by: Rotem Saado <rotem.saado@intel.com>
Fixes: 89639e06d0 ("iwlwifi: yoyo: support for new DBGI_SRAM region")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220129105618.209f3078bc74.I463530bd2f40daedb39f6d9df987bb7cee209033@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Until now function just got a pointer to some buffer and used it as if
it's good to use with no boundaries about size left in the buffer.
This infra helps for internal functions ops to make sure buffer usage
is in bound of allocation.
We also add external checks with warnings to verify every internal
function didn't exceed usage of the free buffer size.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220129105618.25c90fb14968.Ic8f05581a745d08011ca29b3f42767402643e8c5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The original implementation checked the HW family, and as a result
of that used different addresses for the prph registers.
The old HWs addresses start with 0xa****** and the newer
ones start with 0xd******.
For this there are iwl_read/write_umac_prph functions that just add the
diff in the address automatically (in this case 0x300000), so the code will
be common for all HWs
In the original implementation the address given already had the 0xd******
causing the address to become 0x10***** (after adding the offset)
Change the registers to start with 0xa*****.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211210090244.db2722547eb2.I03dce63698befc2fd9105111c3015b8d6e36868a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In next region tlv (3) region type is going to be split into bit mask
without affecting the ops for handling region type, so we just mask
the type independent of the version due to all versions having the
same bits usage.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204130722.083e4b47055e.If7483d854e3d07f81236d314b8155cd5996f306c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have a MAC component (which is inside the SoC) and it has several
different HW steps. 3 bits used to be enough but now we need 4-bits
to represent all the different steps.
Properly support 4-bits in the MAC step value by refactoring all the
current handling of the MAC step/dash.
Already from family 8000 and up the dash (bits 0-1) no longer exists
and the step (until 8000 bits 2-3) consists of the dash bits as well.
To do this remove the CSR_HW_REV_STEP and the CSR_HW_REV_DASH
macros, replace them with CSR_HW_REV_STEP_DASH and add hw_rev_step
into the trans struct.
In addition remove the CSR_HW_IF_CONFIG_REG_MSK_MAC_STEP and
CSR_HW_IF_CONFIG_REG_MSK_MAC_DASH macros and create a new macro
combining the 2 (this way we don't need shifting or anything else.)
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Mike Golant <michael.golant@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211207160459.2e81a14d1f80.Ia5287e37fb3439d805336837361f6491f958e465@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In firmware dumps, currently all kinds of key material may be
included, e.g. in host commands (if firmware crashes during the
processing of a key-related command) or in the TX FIFO(s) if
we have been using in-TX-command key material.
Additionally, some firmware versions will advertise sections
of their internal data to not dump, due to them containing some
sensitive data.
Add some infrastructure to allow scrubbing this data out, as
dependent on the opmode's idea of what will need to be done.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017123741.360cc8fe55b1.Ie3bd3ece38043969f7e116e61a6ec1197a58d78b@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When having a blank OTP the only way to get the rf id
and the cdb info is from prph registers.
Currently there is some implementation for this, but it
is located in the wrong place in the code (should be before
trying to understand what HW is connected and not after),
and it has a partial implementation.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210826224715.820c2ae18c2b.Iec9b2e2615ce65e6aff5ce896589227a7030f4cf@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The debug dump ranges aren't just an array of such ranges
since each range has a variable size. Therefore, the use
of a struct array is misleading at best.
Change it to be a u8 data[] instead of the struct array,
the code doesn't significantly change since it's actually
doing things correctly now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210819183728.693c9891097d.Idcaab1fd659e8be2f56be647b2534befd61a4460@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In commit 79f033f6f2 ("iwlwifi: dbg: don't limit dump decisions
to all or monitor") we changed the code to pass around a bitmap,
but in the monitor_only case, one place accidentally used the bit
number, not the bit mask, resulting in CSR and FW_INFO getting
dumped instead of monitor data. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.774fd8729a33.Ic985a787071d1c0b127ef0ba8367da896ee11f57@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Conceptually, this belongs more into the firmware utils
rather than the mvm opmode, so move the collection and
output there.
Note that this slightly changes the format of the Status
line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210621103449.b82b60d81346.Ide3b688107f6a59c7fc7eb1d8f2002b0a5c1f2d2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Return value of the iwl_mvm_load_nvm_to_nic func is not analyzed. If load
NVM to nic func fails and NVM is not loaded to fw properly, then fw may
behave badly and lead to some strange issue. This commit will analyze
return value and if load NVM to nic has failed, then the error code is
sent to the previous func, which will trigger WRT log collection.
iwl_fw_dbg_error_collect() func collects dump only if tri type is
FW_DBG_TRIGGER_ALIVE_TIMEOUT. But when Load NVM to nic function fails
trig_type is FW_DBG_TRIGGER_DRIVER. This commit also has code changes to
collect dump when trig_type is FW_DBG_TRIGGER_DRIVER.
Signed-off-by: Abhishek Naik <abhishek.naik@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.32998850192a.Ic58d08cb6944ca55e343ff0032c82cfa7821e588@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case user requested to register an unsupported regions,
remove it from active list and trigger list, this saves operational
driver memory and run time at collecting debug data.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210142629.a0cc944040e8.I3ae37547452b39f8040428c21ed47bdc67ae8f71@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/fw/dbg.c:1932: warning: Function parameter or member 'reg_data' not described in 'iwl_dump_ini_mem'
drivers/net/wireless/intel/iwlwifi/fw/dbg.c:1932: warning: Excess function parameter 'reg' description in 'iwl_dump_ini_mem'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126133152.3211309-15-lee.jones@linaro.org
IWL_WARN seems excessive here since this can happen during normal
operation. Every time I connect to a new network with 8086:24fd I get
this as KERN_WARNING on the console, which mildly distracts from other
more pressing messages. For example:
% sudo journalctl _TRANSPORT=kernel | grep -c 'FW already configured'
403
Signed-off-by: Chris Down <chris@chrisdown.name>
Cc: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Link: https://lore.kernel.org/r/20191017144841.GA16393@chrisdown.name
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several "flavors" of HW that have the same HW type, but
can be told apart after reading a certain perph register. This
is easy to do in runtime, but more complicated to do when looking
at the logs offline.
To make it easier to tell apart these "flavors" when looking at
the dumped dbg info, add these bits to the HW type, allowing
simple differentiation.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.330ea11d17ae.Ie59b25430a308090b15112ac6deedf4fbf487ff1@changeid
