This is a preparation patch for the removal of the DSA switch methods
->port_bridge_tx_fwd_offload() and ->port_bridge_tx_fwd_unoffload().
The plan is for the switch to report whether it offloads TX forwarding
directly as a response to the ->port_bridge_join() method.
This change deals with the noisy portion of converting all existing
function prototypes to take this new boolean pointer argument.
The bool is placed in the cross-chip notifier structure for bridge join,
and a reference to it is provided to drivers. In the next change, DSA
will then actually look at this value instead of calling
->port_bridge_tx_fwd_offload().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The main desire behind this is to provide coherent bridge information to
the fast path without locking.
For example, right now we set dp->bridge_dev and dp->bridge_num from
separate code paths, it is theoretically possible for a packet
transmission to read these two port properties consecutively and find a
bridge number which does not correspond with the bridge device.
Another desire is to start passing more complex bridge information to
dsa_switch_ops functions. For example, with FDB isolation, it is
expected that drivers will need to be passed the bridge which requested
an FDB/MDB entry to be offloaded, and along with that bridge_dev, the
associated bridge_num should be passed too, in case the driver might
want to implement an isolation scheme based on that number.
We already pass the {bridge_dev, bridge_num} pair to the TX forwarding
offload switch API, however we'd like to remove that and squash it into
the basic bridge join/leave API. So that means we need to pass this
pair to the bridge join/leave API.
During dsa_port_bridge_leave, first we unset dp->bridge_dev, then we
call the driver's .port_bridge_leave with what used to be our
dp->bridge_dev, but provided as an argument.
When bridge_dev and bridge_num get folded into a single structure, we
need to preserve this behavior in dsa_port_bridge_leave: we need a copy
of what used to be in dp->bridge.
Switch drivers check bridge membership by comparing dp->bridge_dev with
the provided bridge_dev, but now, if we provide the struct dsa_bridge as
a pointer, they cannot keep comparing dp->bridge to the provided
pointer, since this only points to an on-stack copy. To make this
obvious and prevent driver writers from forgetting and doing stupid
things, in this new API, the struct dsa_bridge is provided as a full
structure (not very large, contains an int and a pointer) instead of a
pointer. An explicit comparison function needs to be used to determine
bridge membership: dsa_port_offloads_bridge().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The location of the bridge device pointer and number is going to change.
It is not going to be kept individually per port, but in a common
structure allocated dynamically and which will have lockdep validation.
Use the helpers to access these elements so that we have a migration
path to the new organization.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix warning reported by bot.
Make sure hash is init to 0 and fix wrong logic for hash_type in
qca8k_lag_can_offload.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: def975307c ("net: dsa: qca8k: add LAG support")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211123154446.31019-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add LAG support to this switch. In Documentation this is described as
trunk mode. A max of 4 LAGs are supported and each can support up to 4
port. The current tx mode supported is Hash mode with both L2 and L2+3
mode.
When no port are present in the trunk, the trunk is disabled in the
switch.
When a port is disconnected, the traffic is redirected to the other
available port.
The hash mode is global and each LAG require to have the same hash mode
set. To change the hash mode when multiple LAG are configured, it's
required to remove each LAG and set the desired hash mode to the last.
An error is printed when it's asked to set a not supported hadh mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports mirror mode. Only one port can set as mirror port and
every other port can set to both ingress and egress mode. The mirror
port is disabled and reverted to normal operation once every port is
removed from sending packet to it.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for mdb add/del function. The ARL table is used to insert
the rule. The rule will be searched, deleted and reinserted with the
port mask updated. The function will check if the rule has to be updated
or insert directly with no deletion of the old rule.
If every port is removed from the port mask, the rule is removed.
The rule is set STATIC in the ARL table (aka it doesn't age) to not be
flushed by fast age function.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k support setting ageing time in step of 7s. Add support for it and
set the max value accepted of 7645m.
Documentation talks about support for 10000m but that values doesn't
make sense as the value doesn't match the max value in the reg.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports fast aging by flushing any rule in the ARL
table for a specific port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently missing 2 additionals MIB counter present in QCA833x
switch.
QC832x switch have 39 MIB counter and QCA833X have 41 MIB counter.
Add the additional MIB counter and rework the MIB function to print the
correct supported counter from the match_data struct.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert any qca8k set/clear/pool to regmap helper and add
missing config to regmap_config struct.
Read/write/rmw operation are reworked to use the regmap helper
internally to keep the delta of this patch low. These additional
function will then be dropped when the code split will be proposed.
Ipq40xx SoC have the internal switch based on the qca8k regmap but use
mmio for read/write/rmw operation instead of mdio.
In preparation for the support of this internal switch, convert the
driver to regmap API to later split the driver to common and specific
code. The overhead introduced by the use of regamp API is marginal as the
internal mdio will bypass it by using its direct access and regmap will be
used only by configuration functions or fdb access.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for regmap conversion, move regmap init in the probe
function and make it mandatory as any read/write/rmw operation will be
converted to regmap API.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mutex is already init in sw_probe. Remove the extra init in qca8k_setup.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert and try to standardize bit fields using
GENMASK/FIELD_PREP/FIELD_GET macros. Rework some logic to support the
standard macro and tidy things up. No functional change intended.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The very next check for port 0 and 6 already makes sure we don't go out
of bounds with the ports_config delay table.
Remove the redundant check.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k has a global MTU, so its tracking the MTU per port to make sure
that the largest MTU gets applied.
Since it uses the frame size instead of MTU the driver MTU change function
will then add the size of Ethernet header and checksum on top of MTU.
The driver currently populates the per port MTU size as Ethernet frame
length + checksum which equals 1518.
The issue is that then MTU change function will go through all of the
ports, find the largest MTU and apply the Ethernet header + checksum on
top of it again, so for a desired MTU of 1500 you will end up with 1536.
This is obviously incorrect, so to correct it populate the per port struct
MTU with just the MTU and not include the Ethernet header + checksum size
as those will be added by the MTU change function.
Fixes: f58d2598cf ("net: dsa: qca8k: implement the port MTU callbacks")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With SGMII phy the internal delay is always applied to the PAD0 config.
This is caused by the falling edge configuration that hardcode the reg
to PAD0 (as the falling edge bits are present only in PAD0 reg)
Move the delay configuration before the reg overwrite to correctly apply
the delay.
Fixes: cef0811584 ("net: dsa: qca8k: set internal delay also for sgmii")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some device set MAC06 exchange in the bootloader. This cause some
problem as we don't support this strange mode and we just set the port6
as the primary CPU port. With MAC06 exchange, PAD0 reg configure port6
instead of port0. Add an extra check and explicitly disable MAC06 exchange
to correctly configure the port PAD config.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Fixes: 3fcf734aa4 ("net: dsa: qca8k: add support for cpu port 6")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tidy and organize qca8k setup function from multiple for loop.
Change for loop in bridge leave/join to scan all port and skip cpu port.
No functional change intended.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix delay settings applied to wrong cpu in parse_port_config. The delay
values is set to the wrong index as the cpu_port_index is incremented
too early. Start the cpu_port_index to -1 so the correct value is
applied to address also the case with invalid phy mode and not available
port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ports related config to dedicated struct to keep things organized.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA original code report port instability and sa that SGMII also require
to set internal delay. Generalize the rgmii delay function and apply the
advised value if they are not defined in DT.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA8328 switch is the bigger brother of the qca8327. Same regs different
chip. Change the function to set the correct pin layout and introduce a
new match_data to differentiate the 2 switch as they have the same ID
and their internal PHY have the same ID.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some qca8327 switch require to force the ignore of power on sel
strapping. Some switch require to set the led open drain mode in regs
instead of using strapping. While most of the device implements this
using the correct way using pin strapping, there are still some broken
device that require to be set using sw regs.
Introduce a new binding and support these special configuration.
As led open drain require to ignore pin strapping to work, the probe
fails with EINVAL error with incorrect configuration.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support enabling PLL on the SGMII CPU port. Some device require this
special configuration or no traffic is transmitted and the switch
doesn't work at all. A dedicated binding is added to the CPU node
port to apply the correct reg on mac config.
Fail to correctly configure sgmii with qca8327 switch and warn if pll is
used on qca8337 with a revision greater than 1.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future proof commit. This switch have 2 CPU ports and one valid
configuration is first CPU port set to sgmii and second CPU port set to
rgmii-id. The current implementation detects delay only for CPU port
zero set to rgmii and doesn't count any delay set in a secondary CPU
port. Drop the current delay scan function and move it to the sgmii
parser function to generalize and implicitly add support for secondary
CPU port set to rgmii-id. Introduce new logic where delay is enabled
also with internal delay binding declared and rgmii set as PHY mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently CPU port is always hardcoded to port 0. This switch have 2 CPU
ports. The original intention of this driver seems to be use the
mac06_exchange bit to swap MAC0 with MAC6 in the strange configuration
where device have connected only the CPU port 6. To skip the
introduction of a new binding, rework the driver to address the
secondary CPU port as primary and drop any reference of hardcoded port.
With configuration of mac06 exchange, just skip the definition of port0
and define the CPU port as a secondary. The driver will autoconfigure
the switch to use that as the primary CPU port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for this in the qca8k driver. Also add support for SGMII
rx/tx clock falling edge. This is only present for pad0, pad5 and
pad6 have these bit reserved from Documentation. Add a comment that this
is hardcoded to PAD0 as qca8327/28/34/37 have an unique sgmii line and
setting falling in port0 applies to both configuration with sgmii used
for port0 or port6.
Co-developed-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing mac power sel support needed for ipq8064/5 SoC that require
1.8v for the internal regulator port instead of the default 1.5v.
If other device needs this, consider adding a dedicated binding to
support this.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lino reports that on his system with bcmgenet as DSA master and KSZ9897
as a switch, rebooting or shutting down never works properly.
What does the bcmgenet driver have special to trigger this, that other
DSA masters do not? It has an implementation of ->shutdown which simply
calls its ->remove implementation. Otherwise said, it unregisters its
network interface on shutdown.
This message can be seen in a loop, and it hangs the reboot process there:
unregister_netdevice: waiting for eth0 to become free. Usage count = 3
So why 3?
A usage count of 1 is normal for a registered network interface, and any
virtual interface which links itself as an upper of that will increment
it via dev_hold. In the case of DSA, this is the call path:
dsa_slave_create
-> netdev_upper_dev_link
-> __netdev_upper_dev_link
-> __netdev_adjacent_dev_insert
-> dev_hold
So a DSA switch with 3 interfaces will result in a usage count elevated
by two, and netdev_wait_allrefs will wait until they have gone away.
Other stacked interfaces, like VLAN, watch NETDEV_UNREGISTER events and
delete themselves, but DSA cannot just vanish and go poof, at most it
can unbind itself from the switch devices, but that must happen strictly
earlier compared to when the DSA master unregisters its net_device, so
reacting on the NETDEV_UNREGISTER event is way too late.
It seems that it is a pretty established pattern to have a driver's
->shutdown hook redirect to its ->remove hook, so the same code is
executed regardless of whether the driver is unbound from the device, or
the system is just shutting down. As Florian puts it, it is quite a big
hammer for bcmgenet to unregister its net_device during shutdown, but
having a common code path with the driver unbind helps ensure it is well
tested.
So DSA, for better or for worse, has to live with that and engage in an
arms race of implementing the ->shutdown hook too, from all individual
drivers, and do something sane when paired with masters that unregister
their net_device there. The only sane thing to do, of course, is to
unlink from the master.
However, complications arise really quickly.
The pattern of redirecting ->shutdown to ->remove is not unique to
bcmgenet or even to net_device drivers. In fact, SPI controllers do it
too (see dspi_shutdown -> dspi_remove), and presumably, I2C controllers
and MDIO controllers do it too (this is something I have not researched
too deeply, but even if this is not the case today, it is certainly
plausible to happen in the future, and must be taken into consideration).
Since DSA switches might be SPI devices, I2C devices, MDIO devices, the
insane implication is that for the exact same DSA switch device, we
might have both ->shutdown and ->remove getting called.
So we need to do something with that insane environment. The pattern
I've come up with is "if this, then not that", so if either ->shutdown
or ->remove gets called, we set the device's drvdata to NULL, and in the
other hook, we check whether the drvdata is NULL and just do nothing.
This is probably not necessary for platform devices, just for devices on
buses, but I would really insist for consistency among drivers, because
when code is copy-pasted, it is not always copy-pasted from the best
sources.
So depending on whether the DSA switch's ->remove or ->shutdown will get
called first, we cannot really guarantee even for the same driver if
rebooting will result in the same code path on all platforms. But
nonetheless, we need to do something minimally reasonable on ->shutdown
too to fix the bug. Of course, the ->remove will do more (a full
teardown of the tree, with all data structures freed, and this is why
the bug was not caught for so long). The new ->shutdown method is kept
separate from dsa_unregister_switch not because we couldn't have
unregistered the switch, but simply in the interest of doing something
quick and to the point.
The big question is: does the DSA switch's ->shutdown get called earlier
than the DSA master's ->shutdown? If not, there is still a risk that we
might still trigger the WARN_ON in unregister_netdevice that says we are
attempting to unregister a net_device which has uppers. That's no good.
Although the reference to the master net_device won't physically go away
even if DSA's ->shutdown comes afterwards, remember we have a dev_hold
on it.
The answer to that question lies in this comment above device_link_add:
* A side effect of the link creation is re-ordering of dpm_list and the
* devices_kset list by moving the consumer device and all devices depending
* on it to the ends of these lists (that does not happen to devices that have
* not been registered when this function is called).
so the fact that DSA uses device_link_add towards its master is not
exactly for nothing. device_shutdown() walks devices_kset from the back,
so this is our guarantee that DSA's shutdown happens before the master's
shutdown.
Fixes: 2f1e8ea726 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mdio legacy mapping is used the mii_bus priv registered by DSA
refer to the dsa switch struct instead of the qca8k_priv struct and
causes a kernel panic. Create dedicated function when the internal
dedicated mdio driver is used to properly handle the 2 different
implementation.
Fixes: 759bafb8a3 ("net: dsa: qca8k: add support for internal phy and internal mdio")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code check "reg" but "ret" was intended so the error handling will
never trigger.
Fixes: 7c9896e378 ("net: dsa: qca8k: check return value of read functions correctly")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "hi" variable is a u64 but the qca8k_read() writes to the top 32
bits of it. That will work on little endian systems but it's a bit
subtle. It's cleaner to make declare "hi" as a u32. We will still need
to cast it when we shift it later on in the function but that's fine.
Fixes: 7c9896e378 ("net: dsa: qca8k: check return value of read functions correctly")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we can check qca8k_read() return value correctly, so if
it fails, we need return directly.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current return type of qca8k_mii_read32() and qca8k_read() are
unsigned, it can't be negative, so the return value check is
unuseful. For check the return value correctly, change return
type of the read functions and add a output parameter to store
the read value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the missing unlock before return from function qca8k_vlan_add()
and qca8k_vlan_del() in the error handling case.
Fixes: 028f5f8ef4 ("net: dsa: qca8k: handle error with qca8k_read operation")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define get_phy_flags to pass switch_Revision needed to tweak the
internal PHY with debug values based on the revision.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the internal mdio read/write bus access by caching the value
without accessing it for every read/write.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to setup_mdio_bus for internal phy declaration. Introduce a
flag to use the legacy port phy mapping by default and use the direct
mapping if a mdio node is detected in the switch node. Register a
dedicated mdio internal mdio bus to address the different mapping
between port and phy if the mdio node is detected.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The witch require some extra delay after setting page or the next
read/write can use still use the old page. Add a delay after the
set_page function to address this as it's done in QSDK legacy driver.
Some timeouts were notice with VLAN and phy function, enlarge the
mdio busy wait timeout to fix these problems.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO_MASTER operation have a dedicated busy wait that is not protected
by the mdio mutex. This can cause situation where the MASTER operation
is done and a normal operation is executed between the MASTER read/write
and the MASTER busy_wait. Rework the qca8k_mdio_read/write function to
address this issue by binding the lock for the whole MASTER operation
and not only the mdio read/write common operation.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear MDIO_MASTER_EN bit from MDIO_MASTER_CTRL after read/write
operation. The MDIO_MASTER_EN bit is not reset after read/write
operation and the next operation can be wrongly interpreted by the
switch as a mdio operation. This cause a production of wrong/garbage
data from the switch and underfined bheavior. (random port drop,
unplugged port flagged with link up, wrong port speed)
Also on driver remove the MASTER_CTRL can be left set and cause the
malfunction of any next driver using the mdio device.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy qsdk code used a different delay instead of the max value.
Qsdk use 1 ns for rx and 2 ns for tx. Make these values configurable
using the standard rx/tx-internal-delay-ps ethernet binding and apply
qsdk values by default. The connected gmac doesn't add any delay so no
additional delay is added to tx/rx.
On this switch the delay is actually in ns so value should be in the
1000 order. Any value converted from ps to ns by dividing it by 1000
as the switch max value for delay is 3ns.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dsa now also supports ethernet-ports. Add this new binding as a fallback
if the ports node can't be found.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k internal phy driver require some special debug value to be set
based on the switch revision. Rework the switch id read function to
also read the chip revision.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch qca8327 needs special settings for the GLOBAL_FC_THRES regs.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit port5 rx delay to qca8337. This is taken from the legacy QSDK code
that limits the rx delay on port5 to only this particular switch version,
on other switch only the tx and rx delay for port0 are needed.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port 5 of the qca8337 have some problem in flood condition. The
original legacy driver had some specific buffer and priority settings
for the different port suggested by the QCA switch team. Add this
missing settings to improve switch stability under load condition.
The packet priority tweak is only needed for the qca8337 switch and
other qca8k switch are not affected.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
