We used to use the function i40e_vlan_rx_register as a way to hook
into the now defunct .ndo_vlan_rx_register netdev hook. This was
removed but we kept the function around because we still used it
internally to control enabling or disabling of VLAN stripping.
As pointed out in upstream review, VLAN stripping is only used in a
single location and the previous function is quite small, just inline
it into i40e_restore_vlan() rather than carrying the function
separately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces new ethtool private flag used for
forcing true link state. Function i40e_force_link_state that implements
this functionality was added, it sets phy_type = 0 in order to
work-around firmware's LESM. False positive error messages were
suppressed.
The ndo_open() should not succeed if there were issues with forcing link
state to be UP.
Added I40E_PHY_TYPES_BITMASK define with all phy types OR-ed together in
one bitmask. Added after phy type definition, so it will be hard to
forget to include new phy types to the bitmask.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch provides support to add or delete cloud filter for queue
channels created for ADq on VF.
We are using the HW's cloud filter feature and programming it to act
as a TC filter applied to a group of queues.
There are two possible modes for a VF when applying a cloud filter
1. Basic Mode: Intended to apply filters that don't need a VF to be
Trusted. This would include the following
Dest MAC + L4 port
Dest MAC + VLAN + L4 port
2. Advanced Mode: This mode is only for filters with combination that
requires VF to be Trusted.
Dest IP + L4 port
When cloud filters are applied on a trusted VF and for some reason
the same VF is later made as untrusted then all cloud filters
will be deleted. All cloud filters has to be re-applied in
such a case.
Cloud filters are also deleted when queue channel is deleted.
Testing-Hints:
=============
1. Adding Basic Mode filter should be possible on a VF in
Non-Trusted mode.
2. In Advanced mode all filters should be able to be created.
Steps:
======
1. Enable ADq and create TCs using TC mqprio command
2. Apply cloud filter.
3. Turn-off the spoof check.
4. Pass traffic.
Example:
========
1. tc qdisc add dev enp4s2 root mqprio num_tc 4 map 0 0 0 0 1 2 2 3\
queues 2@0 2@2 1@4 1@5 hw 1 mode channel
2. tc qdisc add dev enp4s2 ingress
3. ethtool -K enp4s2 hw-tc-offload on
4. ip link set ens261f0 vf 0 spoofchk off
5. tc filter add dev enp4s2 protocol ip parent ffff: prio 1 flower\
dst_ip 192.168.3.5/32 ip_proto udp dst_port 25 skip_sw hw_tc 2
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MAC, FW Version and NPAR check used to determine
if shutting off the FW LLDP engine is supported is not
using the usual feature check mechanism.
This patch fixes the problem by moving the feature check
to i40e_sw_init in order to set a flag in pf->hw_features
that ethtool will use for priv_flags disable operation.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Broadcast filters can now cause overflow promiscuous to trigger when
adding "too many" VLANs to all the ports of a device and the driver
needs a way to exit overflow promiscuous once triggered.
Currently the driver looks to see if there are "too many" filters and/or
we have any failed filters to determine when it is safe to exit overflow
promiscuous. If we trigger overflow promiscuous with broadcast filters,
any new filters added will be "auto-failed" until we exit overflow
promiscuous. Since the user can't manually remove the failed broadcast
filters for VLANs (nor should we expect the user to do such), there is
no way to exit overflow promiscuous without reloading the driver.
The easiest way to do this is to remove the shortcut to "auto-fail"
filters in overflow promiscuous. If the user removes the VLANs, the
failed filters will be removed and since we're no longer "auto-failing"
new filters, we'll eventually get a good set of filters and exit
overflow promiscuous.
This has the side benefit of making filter state more explicit in that
if a filter says it's failed we know for a fact it failed and not just
assuming it will if we're in overflow promiscuous. This is nice because
if the user removes some filters and then adds some, even if we're in
overflow promiscuous, the filter might succeed; we were just assuming it
won't because the user hasn't rectified other existing failed filters.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code here is quite complex and easy to screw up. Let's see if we
can't improve the readability and maintainability a bit. This refactors
out promisc_changed into two variables 'old_overflow' and 'new_overflow'
which makes it a bit clearer when we're concerned about when and how
overflow promiscuous is changed. This also makes so that we no longer
need to pass a boolean pointer to i40e_aqc_add_filters. Instead we can
simply check if we changed the overflow promiscuous flag since the
function start.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When adding a bunch of VLANs to all the ports on a device, it's possible
to run out of space for broadcast filters. The driver should trigger
overflow promiscuous in this circumstance to prevent traffic from being
unexpectedly dropped.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Could a Bad Person do Bad Things to a server if they found these
addresses printed in the log? Who knows? But let's not take that risk.
Remove pointers from a bunch of printks. In some cases, I was able to
adjust the message to indicate whether or not the value was null. In
others, I just removed the entire message as there was really no hope of
saving it.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes the following sparse warning:
drivers/net/ethernet/intel/i40e/i40e_main.c:5440:5: warning:
symbol 'i40e_get_link_speed' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces the existing mechanism for determining the correct
value to program for adaptive ITR with yet another new and more
complicated approach.
The basic idea from a 30K foot view is that this new approach will push the
Rx interrupt moderation up so that by default it starts in low latency and
is gradually pushed up into a higher latency setup as long as doing so
increases the number of packets processed, if the number of packets drops
to 4 to 1 per packet we will reset and just base our ITR on the size of the
packets being received. For Tx we leave it floating at a high interrupt
delay and do not pull it down unless we start processing more than 112
packets per interrupt. If we start exceeding that we will cut our interrupt
rates in half until we are back below 112.
The side effect of these patches are that we will be processing more
packets per interrupt. This is both a good and a bad thing as it means we
will not be blocking processing in the case of things like pktgen and XDP,
but we will also be consuming a bit more CPU in the cases of things such as
network throughput tests using netperf.
One delta from this versus the ixgbe version of the changes is that I have
made the interrupt moderation a bit more aggressive when we are in bulk
mode by moving our "goldilocks zone" up from 48 to 96 to 56 to 112. The
main motivation behind moving this is to address the fact that we need to
update less frequently, and have more fine grained control due to the
separate Tx and Rx ITR times.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is mostly prep-work for replacing the current approach to
programming the dynamic aka adaptive ITR. Specifically here what we are
doing is splitting the Tx and Rx ITR each into two separate values.
The first value current_itr represents the current value of the register.
The second value target_itr represents the desired value of the register.
The general plan by doing this is to allow for deferring the update of the
ITR value under certain circumstances. For now we will work with what we
have, but in the future I hope to change the behavior so that we always
only update one ITR at a time using some simple logic to determine which
ITR requires an update.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds necessary delay for 4.33 firmware to recover after
EMP reset. Without this patch driver occasionally reinitializes
structures too quickly to communicate with firmware after EMP reset
causing AdminQ to timeout.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rings are already split out into Tx and Rx rings so it doesn't make
sense to have any single ring store both a Tx and Rx itr_setting value.
Since that is the case drop the pair in favor of storing just a single ITR
value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the number of queues per enabled TC and report available queues
to the kernel without having to limit them to the max RSS limit so
they are available to be mapped for XPS. This allows a queue per
processing thread available for handling traffic for the given
traffic class.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch suppresses the message about invalid TC mapping and wrong
selected TX queue. The root cause of this bug was setting too many
TC queue pairs on huge multiprocessor machines. When quantity of the
TC queue pairs is exceeding MSI-X vectors count then TX queue number
can be selected beyond actual TX queues amount.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The drivers for i40e and i40evf had a reg_idx value stored in the q_vector
that was going completely unused. I can only assume this was copied over
from ixgbe and nobody knew how to use it.
I'm going to make use of the value to avoid having to compute the vector
and thus the register index for multiple paths throughout the drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When implementing support for IP_USER_FLOW filters, we correctly
programmed a filter for both the non fragmented IPv4/Other filter, as
well as the fragmented IPv4 filters. However, we did not properly
program the input set for fragmented IPv4 PCTYPE. This meant that the
filters would almost certainly not match, unless the user specified all
of the flow types.
Add support to program the fragmented IPv4 filter input set. Since we
always program these filters together, we'll assume that the two input
sets must match, and will thus always program the input sets to the same
value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
kdump fails in the system when used in conjunction with Ethernet driver
X722/X710. This is mainly because when we are resource constrained i.e.
when we have just one online_cpus, we are enabling VMDq and iWARP. It
doesn't make sense to enable them with just one CPU and starve kdump
for lack of IRQs.
So don't enable VMDq or iWARP when we just have a single CPU.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using ethtool --set-priv-flags disable-fw-lldp <on/off> is persistent
across reboots/reloads so we need some mechanism in the driver to detect
if it's on or off on init so we can set the ethtool private flag
appropriately. Without this, every time the driver is reloaded the flag
will default to off regardless of whether it's on or off in FW.
We detect this by first attempting to program DCB and if AQ fails
returning I40E_AQ_RC_EPERM, we know that LLDP is disabled in FW.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement the private flag disable-fw-lldp for ethtool
to disable the processing of LLDP packets by the FW.
This will stop the FW from consuming LLDPDU and cause
them to be sent up the stack.
The FW is also being configured to apply a default DCB
configuration on link up.
Toggling the value of this flag will also cause a PF reset.
Disabling FW DCB will also disable DCBx.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Fixes: 44ae12a768 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix recreating the channel VSIs during the reset flow to reconfigure
the Tx rings and the queue context associated with the channel VSI.
Also update the next_base_queue for the VSI while rebuilding the
channel VSIs after a reset.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that i40e_vsi_config_tc() has the pf and hw variable defined, use
them, instead of dereferencing vsi->back. Much easier to read.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver (and the entire netdev layer for that matter) assumes
that TC0 will always be present in our DCB configuration.
Unfortunately, this isn't always the case. Rather than fail to
configure the VSI, let's go ahead and try to make it work, even
though DCB will end up being disabled by the kernel.
If the driver fails to configure DCB, the driver queries what's
valid, then writes that back to the hardware, always forcing TC0.
This fixes a bug where the driver could fail to adhere to ETS BW
allocations if 8 TCs were configured on the switch.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In VFs, there is a known issue which can cause writebacks
to not occur when interrupts are disabled and there are
less than 4 descriptors resulting in TX timeout. Timeout
can also occur due to lost interrupt.
The current implementation for detecting and recovering
from hung queues in the PF is problematic because it actually
actively encourages lost interrupts. By triggering a SW
interrupt, interrupts are forced on. If we are already in
napi_poll and an interrupt fires, napi_poll will not be
rescheduled and the interrupt is effectively lost; thereby
potentially *causing* hung queues.
This patch checks whether packets are being processed between
every watchdog cycle and determine potential hung queue and
fires triggers SW interrupt only for that particular queue.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some weird circumstances with DCB enabled, the firmware can fail to
configure the VSI, leaving us with zero traffic classes. Check for this
state when we configure RSS to avoid a panic.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds new I40E_NVMUPD_GET_AQ_EVENT state to allow
retrieval of AdminQ events as a result of AdminQ commands sent
to firmware.
Add preservation flags support on X722 devices for NVM update
AdminQ function wrapper. Add new parameter and handling to
nvmupdate admin queue function intended to allow nvmupdate tool
to configure the preservation flags in the AdminQ command.
This is required to implement FlatNVM on X722 devices.
Signed-off-by: Pawel Jablonski <pawel.jablonski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump the i40e driver from 2.1.14 to 2.3.2.
Bump the i40evf driver from 3.0.1 to 3.2.2
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When filter configuration is not supported, drivers should return
-EOPNOTSUPP so the core can react correctly.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, such as with bridging, it is possible that the
stack will add a devices own MAC address to its unicast address list.
If, later, the stack deletes this address, then the i40e driver will
receive a request to remove this address.
The driver stores its current MAC address as part of the MAC/VLAN hash
array, since it is convenient and matches exactly how the hardware
expects to be told which traffic to receive.
This causes a problem, since for more devices, the MAC address is stored
separately, and requests to delete a unicast address should not have the
ability to remove the filter for the MAC address.
Fix this by forcing a check on every address sync to ensure we do not
remove the device address.
There is a very narrow possibility of a race between .set_mac and
.set_rx_mode, if we don't change netdev->dev_addr before updating our
internal MAC list in .set_mac. This might be possible if .set_rx_mode is
going to remove MAC "XYZ" from the list, at the same time as .set_mac
changes our dev_addr to MAC "XYZ", we might possibly queue a delete,
then an add in .set_mac, then queue a delete in .set_rx_mode's
dev_uc_sync and then update netdev->dev_addr. We can avoid this by
moving the copy into dev_addr prior to the changes to the MAC filter
list.
A similar race on the other side does not cause problems, as if we're
changing our MAC form A to B, and we race with .set_rx_mode, it could
queue a delete from A, we'd update our address, and allow the delete.
This seems like a race, but in reality we're about to queue a delete of
A anyways, so it would not cause any issues.
A race in the initialization code is unlikely because the netdevice has
not yet been fully initialized and the stack should not be adding or
removing addresses yet.
Note that we don't (yet) need similar code for the VF driver because it
does not make use of __dev_uc_sync and __dev_mc_sync, but instead roles
its own method for handling updates to the MAC/VLAN list, which already
has code to protect against removal of the hardware address.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since UDP based filters are not supported via big buffer cloud
filters, remove UDP support. Also change a few return types to
indicate unsupported vs invalid configuration.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding cloud filters could fail for a number of reasons,
unsupported filter fields for example, which fails during
validation of fields itself. This will not result in admin
command errors and converting the admin queue status to posix
error code using i40e_aq_rc_to_posix would result in incorrect
error values. If the failure was due to AQ error itself,
reporting that correctly is handled in the inner function.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After a reset we rebuild the VSIs which is going to clobber any
promiscuous settings we had before reset. This makes it so that we
restore the promiscuous settings we had before reset.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is safe to remove the upper limit of 64 queues on a channel
VSI. The upper bound is determined by the VSI's num_queue_pairs
and gets validated when the queue mapping info through mqprio
interface is subject to bound checking in the driver.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_xdp is a control path callback for setting up XDP in the
driver. We can reuse it for other forms of communication
between the eBPF stack and the drivers. Rename the callback
and associated structures and definitions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables tc-flower based hardware offloads. tc flower
filter provided by the kernel is configured as driver specific
cloud filter. The patch implements functions and admin queue
commands needed to support cloud filters in the driver and
adds cloud filters to configure these tc-flower filters.
The classification function of the filter is to direct matched
packets to a traffic class. The hardware traffic class is set
based on the the classid reserved in the range :ffe0 - :ffef.
Match Dst MAC and route to TC0:
prio 1 flower dst_mac 3c:fd:fe:a0:d6:70 skip_sw\
hw_tc 1
Match Dst IPv4,Dst Port and route to TC1:
prio 2 flower dst_ip 192.168.3.5/32\
ip_proto udp dst_port 25 skip_sw\
hw_tc 2
Match Dst IPv6,Dst Port and route to TC1:
prio 3 flower dst_ip fe8::200:1\
ip_proto udp dst_port 66 skip_sw\
hw_tc 2
Delete tc flower filter:
Example:
Flow Director Sideband is disabled while configuring cloud filters
via tc-flower and until any cloud filter exists.
Unsupported matches when cloud filters are added using enhanced
big buffer cloud filter mode of underlying switch include:
1. source port and source IP
2. Combined MAC address and IP fields.
3. Not specifying L4 port
These filter matches can however be used to redirect traffic to
the main VSI (tc 0) which does not require the enhanced big buffer
cloud filter support.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce the cloud filter data structure and cleanup of cloud
filters associated with the device.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add definitions for L4 filters and switch modes based on cloud filters
modes and extend the set switch config command to include the
additional cloud filter mode.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add mapping of TCs with the seids of the channel VSIs. TC0
will be mapped to the main VSI seid and all other TCs are
mapped to the seid of the corresponding channel VSI.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Whether or not there are vectors_left, we only need to redistribute
our vectors if we didn't get as many as we requested. With the current
check, the code will try to redistribute even if we did in fact get all
the vectors we requested - this can happen when we have more CPUs than
we do vectors. This restores an earlier check to be sure we only
redistribute if we didn't get the full count we requested.
Fixes: 4ce20abc64 (i40e: fix MSI-X vector redistribution if hw limit is reached)
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A cleanup of the PM code left an incorrect #ifdef in place, leading
to a harmless build warning:
drivers/net/ethernet/intel/i40e/i40e_main.c:12223:12: error: 'i40e_resume' defined but not used [-Werror=unused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:12185:12: error: 'i40e_suspend' defined but not used [-Werror=unused-function]
It's easier to use __maybe_unused attributes here, since you
can't pick the wrong one.
Fixes: 0e5d3da400 ("i40e: use newer generic PM support instead of legacy PM callbacks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-17
This series contains updates to i40e and ethtool.
Alan provides most of the changes in this series which are mainly fixes
and cleanups. Renamed the ethtool "cmd" variable to "ks", since the new
ethtool API passes us ksettings structs instead of command structs.
Cleaned up an ifdef that was not accomplishing anything. Added function
header comments to provide better documentation. Fixed two issues in
i40e_get_link_ksettings(), by calling
ethtool_link_ksettings_zero_link_mode() to ensure the advertising and
link masks are cleared before we start setting bits. Cleaned up and fixed
code comments which were incorrect. Separated the setting of autoneg in
i40e_phy_types_to_ethtool() into its own conditional to clarify what PHYs
support and advertise autoneg, and makes it easier to add new PHY types in
the future. Added ethtool functionality to intersect two link masks
together to find the common ground between them. Overhauled i40e to
ensure that the new ethtool API macros are being used, instead of the
old ones. Fixed the usage of unsigned 64-bit division which is not
supported on all architectures.
Sudheer adds support for 25G Active Optical Cables (AOC) and Active Copper
Cables (ACC) PHY types.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches test of .data field to
.function, since .data will be going away.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
