Add support for the RTL9302 SoC and the RTL9302C_2xRTL8224_2XGE
reference board.
The RTL930x family of SoCs are Realtek switches with an embedded MIPS
core (800MHz 34Kc). Most of the peripherals are similar to the RTL838x
SoC and can make use of many existing drivers.
Add in full DSA switch support is still a work in progress.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add device_type = "cpu" to the cpu node for the rtl838x SoC. This
resolves the following dtbs_check complaint:
cpus: cpu@0: 'cache-level' is a required property
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Update the node name for the UARTs to resolve the following dtbs_check
complaints:
uart@2000: $nodename:0: 'uart@2000' does not match '^serial(@.*)?$'
uart@2100: $nodename:0: 'uart@2100' does not match '^serial(@.*)?$'
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The OLB ("Other Logic Block") is a system-controller region hosting
clock, reset and pin controllers. It contains registers such as I2C
speed mode that need to be accessible by other nodes.
Remove fixed-clocks previously used; replace references.
Add parent crystal clock, fixed at 30MHz.
Add pin nodes for all functions.
Add mobileye,eyeq5-olb compatible node, hosting clk, reset and pinctrl.
Add reset and pinctrl references to UART nodes.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
ISA node is required by Loongson64 platforms to initialize
PIO support.
Kernel will hang at boot without ISA node.
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
phy-mode should be rgmii-id to match hardware configuration.
Also there should be a phy-handle to reference phy node.
Fixes: f8a1142507 ("MIPS: Loongson64: Add GMAC support for Loongson-2K1000")
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The correct interrupt line for RTC is line 8 on liointc1.
Fixes: e47084e116 ("MIPS: Loongson64: DTS: Add RTC support to Loongson-2K1000")
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
All internal liointc interrupts are high level triggered.
Fixes: b1a792601f ("MIPS: Loongson64: DeviceTree for Loongson-2K1000")
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Builtin DTBS should never contain memory node as memory is
going to be managed by LEFI interface.
Remove memory node to prevent confliction.
Fixes: b1a792601f ("MIPS: Loongson64: DeviceTree for Loongson-2K1000")
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add various required properties to silent warnings:
arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi:116.16-297.5: Warning (interrupt_provider): /bus@10000000/pci@1a000000: '#interrupt-cells' found, but node is not an interrupt provider
arch/mips/boot/dts/loongson/loongson64_2core_2k1000.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider'
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add it to silent warning:
arch/mips/boot/dts/loongson/ls7a-pch.dtsi:68.16-416.5: Warning (interrupt_provider): /bus@10000000/pci@1a000000: '#interrupt-cells' found, but node is not an interrupt provider
arch/mips/boot/dts/loongson/loongson64g_4core_ls7a.dts:32.31-40.4: Warning (interrupt_provider): /bus@10000000/msi-controller@2ff00000: Missing '#interrupt-cells' in interrupt provider
arch/mips/boot/dts/loongson/loongson64g_4core_ls7a.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider'
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
EyeQ6H (or “High”) is an other SoC from Mobileye still based on the
MIPS I6500 architecture as the EyeQ5. The 2 clusters of this SoC
contains 4 cores which are capable of running 4 threads. Besides this,
it features multiple controllers such as the classic UART, high speed
I2C, SPI, as well as CAN-FD, PCIe Gen4, Octal/Quad SPI Flash
interface, Gigabit Ethernet, MIPI CSI-2, MIPI DSI, and eMMC 5.1. It
also includes a Hardware Security Module, Functional Safety Hardware,
and video encoders and more.
This commit provides the infrastructure to build a kernel running on
EyeQ6H SoC. For now the support is limited and only one CPU core is
running.
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
EyeQ6H (or “High”) is an other SoC from Mobileye still based on the
MIPS I6500 architecture as the EyeQ5. The 2 clusters of this SoC
contains 4 cores which are capable of running 4 threads. Besides this,
it features multiple controllers such as the classic UART, high speed
I2C, SPI, as well as CAN-FD, PCIe Gen4, Octal/Quad SPI Flash
interface, Gigabit Ethernet, MIPI CSI-2, MIPI DSI, and eMMC 5.1. It
also includes a Hardware Security Module, Functional Safety Hardware,
and video encoders and more.
This commit provides the initial device tree files with support for
UART, GPIO and pinctrl, as well as fixed clocked.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Move the compatible attribute of the DTS root node to first place.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the attributes of the PCIe PHY nodes node to match
what the DTS style guide recommends.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the attributes and child nodes of the PCIe Controller
node to meet the DTS style guidelines.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Rearrange attributes and descendents declared under the
ethernet node, recursively, to follow the DTS style guide.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the attributes of the Global Interrupt Controller
node to fit DTS style guidelines.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Shuffle the attributes of the MMC node to meet the guidelines
provided by the DTS style guide.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Move the pinctrl node prior to the nodes that feature unit
addresses.
Sort pinctrl's child nodes into alphabetical order.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the attributes of the SPI controller node so that
they're aligned with the DTS style guide.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Rearrange the order of the i2c node's attributes so that they
are inline with the DTS style guide.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Shuffle the attributes of the gpio node to appease the DTS
style guide.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the attributes of the sysc node so that the
ralink prefixed attribute is placed after those which lack
prefixes.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the attributes of MMC fixed voltage regulator nodes
for the sake of compliance with the DTS style guide.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the CPU Interrupt Controller node's attributes to follow
what the DTS Coding Style dictates.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder cpu node attributes to fit the DTS Coding Style.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add default #address-cells and #size-cells properties to the
usb node, which should be suitable for hubs and devices without
explicitly declared interface nodes, as:
"#address-cells":
description: should be 1 for hub nodes with device nodes,
should be 2 for device nodes with interface nodes.
enum: [1, 2]
"#size-cells":
const: 0
-- from Documentation/devicetree/bindings/usb/usb-device.yaml
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add serial1 and serial2 nodes to define the existence of
the MT7621's second and third UARTs.
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder serial0 properties according to the guidelines laid
out in Documentation/devicetree/bindings/dts-coding-style.rst
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add missing pinctrl-name and pinctrl-0 properties to declare
that the uart1_pins group is associated with serial0.
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add a device tree for the Mobileye EPM5 evaluation board.
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add a device tree include file for the Mobileye EyeQ5 SoC.
Based on the work of Slava Samsonov <stanislav.samsonov@intel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Device binds to proper PCI ID (LOONGSON, 0x7a03), already listed in DTS,
so checking for some other compatible does not make sense. It cannot be
bound to unsupported platform.
Drop useless, incorrect (space in between) and undocumented compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename GB-PC1 to GnuBee GB-PC1, and GB-PC2 to GnuBee GB-PC2 to include
brand and model name.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Each item of the resets property should define a reset. Split the item with
two resets on the ethernet node into two separate items.
Sort the items of the clocks property to the same line as a trivial change.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The "probe-type" property was only needed when used with the
(long obsolete) "direct-mapped" compatible value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add missing whitespace between node name/label and opening {.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The module is now supported, enable it.
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The RTC module is now supported, enable it.
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Commit 08384e80a7 ("MIPS: DTS: CI20: Fix ACT8600 regulator node
names") caused the VDDCORE power supply (regulated by the ACT8600's
DCDC1 output) to drop from a voltage of 1.2V configured by the
bootloader, to the 1.1V set in the Device Tree.
According to the documentation, the VDDCORE supply should be between
0.99V and 1.21V; both values are therefore within the supported range.
However, VDDCORE being 1.1V results in the CI20 being very unstable,
with corrupted memory, failures to boot, or reboots at random. The
reason might be succint drops of the voltage below the minimum required.
Raising the minimum voltage to 1.125 volts seems to be enough to address
this issue, while still keeping a relatively low core voltage which
helps for power consumption and thermals.
Fixes: 08384e80a7 ("MIPS: DTS: CI20: Fix ACT8600 regulator node names")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This WiFi AP is based on a MT7621 SoC with 128MiB RAM, 128MiB NAND,
a MT7603 2.4GHz WiFi and a MT7613 5GHz WiFi chips integrated on the board,
connected to the main SoC over PCIe.
The device uses NMBM over NAND, which is not currently supported in the
mainline, so NAND node is skipped in this revision.
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Wire the WiFi/Bluetooth chip properly in the Device Tree.
- Provide it with the correct regulators and clocks;
- Change the MMC I/O bus to 1.8V which seems to be enough;
- Change the MMC I/O bus frequency to 25 MHz as 50 MHz causes errors;
- Fix the Bluetooth powerdown GPIO being inverted and add reset GPIO;
- Convert host-wakeup-gpios to IRQ.
With these changes, the WiFi works properly with the latest firmware
provided by linux-firmware. The Bluetooth does not work very well here,
as I cannot get my wireless keyboard to pair; but it does detect it, and
it does see the key presses when I type the pairing code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This makes it possible to clock the SD cards much higher, as the MPLL is
running at 1.2 GHz by default. The previous parent was the EXT clock,
which caused the SD cards to be clocked at 24 MHz maximum.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- Use the standard "ecc-engine" property instead of the custom
"ingenic,bch-controller" to get a handle to the BCH controller.
- Respect cell sizes in the Ethernet controller node.
- Use proper macro for interrupt type instead of hardcoding magic
values.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
These regulators should be enabled by their respective drivers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Provide parent regulators to the ACT8600 regulators that need one.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The Device Tree was using invalid node names for the ACT8600 regulators.
To be fair, it is not the original committer's fault, as the
documentation did gives invalid names as well.
In theory, the fix should have been to modify the driver to accept the
alternative names. However, even though the act8865 driver spits
warnings, the kernel seemed to work fine with what is currently
supported upstream. For that reason, I think it is okay to just update
the DTS.
I removed the "regulator-name" too, since they really didn't bring any
information. The node names are enough.
Fixes: 73f2b94047 ("MIPS: CI20: DTS: Add I2C nodes")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The regulators don't have any "reg" property, and therefore shouldn't
use an unit address in their node names. They also don't need to specify
the GPIO_ACTIVE_LOW flag, which will be ignored anyway, as they are
active-high.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
