The Linux-internal Xlinuxenvcfg ISA extension is omitted from the
riscv_isa_ext array because it has no DT binding and should not appear
in /proc/cpuinfo. The logic added in commit 625034abd5 ("riscv: add
ISA extensions validation callback") assumes all extensions are included
in riscv_isa_ext, and so riscv_resolve_isa() wrongly drops Xlinuxenvcfg
from the final ISA string. Instead, accept such Linux-internal ISA
extensions as if they have no validation callback.
Fixes: 625034abd5 ("riscv: add ISA extensions validation callback")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20240718213011.2600150-1-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Instead of grouping all vendor extensions into the same riscv_isa_ext
that standard instructions use, create a struct
"riscv_isa_vendor_ext_data_list" that allows each vendor to maintain
their vendor extensions independently of the standard extensions.
xandespmu is currently the only vendor extension so that is the only
extension that is affected by this change.
An additional benefit of this is that the extensions of each vendor can
be conditionally enabled. A config RISCV_ISA_VENDOR_EXT_ANDES has been
added to allow for that.
Signed-off-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andy Chiu <andy.chiu@sifive.com>
Tested-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Link: https://lore.kernel.org/r/20240719-support_vendor_extensions-v3-1-0af7587bbec0@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Andrew Jones <ajones@ventanamicro.com> says:
Zawrs provides two instructions (wrs.nto and wrs.sto), where both are
meant to allow the hart to enter a low-power state while waiting on a
store to a memory location. The instructions also both wait an
implementation-defined "short" duration (unless the implementation
terminates the stall for another reason). The difference is that while
wrs.sto will terminate when the duration elapses, wrs.nto, depending on
configuration, will either just keep waiting or an ILL exception will be
raised. Linux will use wrs.nto, so if platforms have an implementation
which falls in the "just keep waiting" category (which is not expected),
then it should _not_ advertise Zawrs in the hardware description.
Like wfi (and with the same {m,h}status bits to configure it), when
wrs.nto is configured to raise exceptions it's expected that the higher
privilege level will see the instruction was a wait instruction, do
something, and then resume execution following the instruction. For
example, KVM does configure exceptions for wfi (hstatus.VTW=1) and
therefore also for wrs.nto. KVM does this for wfi since it's better to
allow other tasks to be scheduled while a VCPU waits for an interrupt.
For waits such as those where wrs.nto/sto would be used, which are
typically locks, it is also a good idea for KVM to be involved, as it
can attempt to schedule the lock holding VCPU.
This series starts with Christoph's addition of the riscv
smp_cond_load_relaxed function which applies wrs.sto when available.
That patch has been reworked to use wrs.nto and to use the same approach
as Arm for the wait loop, since we can't have arbitrary C code between
the load-reserved and the wrs. Then, hwprobe support is added (since the
instructions are also usable from usermode), and finally KVM is
taught about wrs.nto, allowing guests to see and use the Zawrs
extension.
We still don't have test results from hardware, and it's not possible to
prove that using Zawrs is a win when testing on QEMU, not even when
oversubscribing VCPUs to guests. However, it is possible to use KVM
selftests to force a scenario where we can prove Zawrs does its job and
does it well. [4] is a test which does this and, on my machine, without
Zawrs it takes 16 seconds to complete and with Zawrs it takes 0.25
seconds.
This series is also available here [1]. In order to use QEMU for testing
a build with [2] is needed. In order to enable guests to use Zawrs with
KVM using kvmtool, the branch at [3] may be used.
[1] https://github.com/jones-drew/linux/commits/riscv/zawrs-v3/
[2] https://lore.kernel.org/all/20240312152901.512001-2-ajones@ventanamicro.com/
[3] https://github.com/jones-drew/kvmtool/commits/riscv/zawrs/
[4] cb2beccebc
Link: https://lore.kernel.org/r/20240426100820.14762-8-ajones@ventanamicro.com
* b4-shazam-merge:
KVM: riscv: selftests: Add Zawrs extension to get-reg-list test
KVM: riscv: Support guest wrs.nto
riscv: hwprobe: export Zawrs ISA extension
riscv: Add Zawrs support for spinlocks
dt-bindings: riscv: Add Zawrs ISA extension description
riscv: Provide a definition for 'pause'
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
RISC-V code uses the generic ticket lock implementation, which calls
the macros smp_cond_load_relaxed() and smp_cond_load_acquire().
Introduce a RISC-V specific implementation of smp_cond_load_relaxed()
which applies WRS.NTO of the Zawrs extension in order to reduce power
consumption while waiting and allows hypervisors to enable guests to
trap while waiting. smp_cond_load_acquire() doesn't need a RISC-V
specific implementation as the generic implementation is based on
smp_cond_load_relaxed() and smp_acquire__after_ctrl_dep() sufficiently
provides the acquire semantics.
This implementation is heavily based on Arm's approach which is the
approach Andrea Parri also suggested.
The Zawrs specification can be found here:
https://github.com/riscv/riscv-zawrs/blob/main/zawrs.adoc
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Co-developed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20240426100820.14762-11-ajones@ventanamicro.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add parsing for Zcmop ISA extension which was ratified in commit
c732a4f39a4c ("Zcmop is ratified/1.0") of the riscv-isa-manual.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Link: https://lore.kernel.org/r/20240619113529.676940-14-cleger@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The Zc* standard extension for code reduction introduces new extensions.
This patch adds support for Zca, Zcf, Zcd and Zcb. Zce, Zcmt and Zcmp
are left out of this patch since they are targeting microcontrollers/
embedded CPUs instead of application processors.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240619113529.676940-9-cleger@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Since a few extensions (Zicbom/Zicboz) already needs validation and
future ones will need it as well (Zc*) add a validate() callback to
struct riscv_isa_ext_data. This require to rework the way extensions are
parsed and split it in two phases. First phase is isa string or isa
extension list parsing and consists in enabling all the extensions in a
temporary bitmask (source isa) without any validation. The second step
"resolves" the final isa bitmap, handling potential missing dependencies.
The mechanism is quite simple and simply validate each extension
described in the source bitmap before enabling it in the resolved isa
bitmap. validate() callbacks can return either 0 for success,
-EPROBEDEFER if extension needs to be validated again at next loop. A
previous ISA bitmap is kept to avoid looping multiple times if an
extension dependencies are never satisfied until we reach a stable
state. In order to avoid any potential infinite looping, allow looping
a maximum of the number of extension we handle. Zicboz and Zicbom
extensions are modified to use this validation mechanism.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240619113529.676940-8-cleger@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add parsing for Zimop ISA extension which was ratified in commit
58220614a5f of the riscv-isa-manual.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Link: https://lore.kernel.org/r/20240619113529.676940-3-cleger@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Make has_vector() to check for ZVE32X. Every in-kernel usage of V that
requires a more complicate version of V must then call out explicitly.
Also, change riscv_v_first_use_handler(), and boot code that calls
riscv_v_setup_vsize() to accept ZVE32X.
Most kernel/user interfaces requires minimum of ZVE32X. Thus, programs
compiled and run with ZVE32X should be supported by the kernel on most
aspects. This includes context-switch, signal, ptrace, prctl, and
hwprobe.
One exception is that ELF_HWCAP returns 'V' only if full V is supported
on the platform. This means that the system without a full V must not
rely on ELF_HWCAP to tell whether it is allowable to execute Vector
without first invoking a prctl() check.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Acked-by: Joel Granados <j.granados@samsung.com>
Link: https://lore.kernel.org/r/20240510-zve-detection-v5-7-0711bdd26c12@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Multiple Vector subextensions are added. Also, the patch takes care of
the dependencies of Vector subextensions by macro expansions. So, if
some "embedded" platform only reports "zve64f" on the ISA string, the
parser is able to expand it to zve32x zve32f zve64x and zve64f.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240510-zve-detection-v5-5-0711bdd26c12@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Single-letter extensions may also imply multiple subextensions. For
example, Vector extension implies zve64d, and zve64d implies zve64f.
Extension parsing for "riscv,isa-extensions" has the ability to resolve
the dependency by calling match_isa_ext(). This patch makes deprecated
parser call the same function for single letter extensions.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240510-zve-detection-v5-3-0711bdd26c12@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The function would fail when it detects the calling hart's vlen doesn't
match the first one's. The boot hart is the first hart calling this
function during riscv_fill_hwcap, so it is impossible to fail here. Add
a comment about this behavior.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240510-zve-detection-v5-1-0711bdd26c12@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
This loop is supposed to check if ext->subset_ext_ids[j] is valid, rather
than if ext->subset_ext_ids[i] is valid, before setting the extension
id ext->subset_ext_ids[j] in isainfo->isa.
Signed-off-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Fixes: 0d8295ed97 ("riscv: add ISA extension parsing for scalar crypto")
Link: https://lore.kernel.org/r/20240502-cpufeature_fixes-v4-2-b3d1a088722d@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The riscv_cpuinfo struct that contains mvendorid and marchid is not
populated until all harts are booted which happens after the DT parsing.
Use the mvendorid/marchid from the boot hart to determine if the DT
contains an invalid V.
Fixes: d82f32202e ("RISC-V: Ignore V from the riscv,isa DT property on older T-Head CPUs")
Signed-off-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20240502-cpufeature_fixes-v4-1-b3d1a088722d@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
* Support for various vector-accelerated crypto routines.
* Hibernation is now enabled for portable kernel builds.
* mmap_rnd_bits_max is larger on systems with larger VAs.
* Support for fast GUP.
* Support for membarrier-based instruction cache synchronization.
* Support for the Andes hart-level interrupt controller and PMU.
* Some cleanups around unaligned access speed probing and Kconfig
settings.
* Support for ACPI LPI and CPPC.
* Various cleanus related to barriers.
* A handful of fixes.
-----BEGIN PGP SIGNATURE-----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=3dL5
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.9-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for various vector-accelerated crypto routines
- Hibernation is now enabled for portable kernel builds
- mmap_rnd_bits_max is larger on systems with larger VAs
- Support for fast GUP
- Support for membarrier-based instruction cache synchronization
- Support for the Andes hart-level interrupt controller and PMU
- Some cleanups around unaligned access speed probing and Kconfig
settings
- Support for ACPI LPI and CPPC
- Various cleanus related to barriers
- A handful of fixes
* tag 'riscv-for-linus-6.9-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (66 commits)
riscv: Fix syscall wrapper for >word-size arguments
crypto: riscv - add vector crypto accelerated AES-CBC-CTS
crypto: riscv - parallelize AES-CBC decryption
riscv: Only flush the mm icache when setting an exec pte
riscv: Use kcalloc() instead of kzalloc()
riscv/barrier: Add missing space after ','
riscv/barrier: Consolidate fence definitions
riscv/barrier: Define RISCV_FULL_BARRIER
riscv/barrier: Define __{mb,rmb,wmb}
RISC-V: defconfig: Enable CONFIG_ACPI_CPPC_CPUFREQ
cpufreq: Move CPPC configs to common Kconfig and add RISC-V
ACPI: RISC-V: Add CPPC driver
ACPI: Enable ACPI_PROCESSOR for RISC-V
ACPI: RISC-V: Add LPI driver
cpuidle: RISC-V: Move few functions to arch/riscv
riscv: Introduce set_compat_task() in asm/compat.h
riscv: Introduce is_compat_thread() into compat.h
riscv: add compile-time test into is_compat_task()
riscv: Replace direct thread flag check with is_compat_task()
riscv: Improve arch_get_mmap_end() macro
...
Charlie Jenkins <charlie@rivosinc.com> says:
If the hardware unaligned access speed is known at compile time, it is
possible to avoid running the unaligned access speed probe to speedup
boot-time.
* b4-shazam-merge:
riscv: Set unaligned access speed at compile time
riscv: Decouple emulated unaligned accesses from access speed
riscv: Only check online cpus for emulated accesses
riscv: lib: Introduce has_fast_unaligned_access()
Link: https://lore.kernel.org/r/20240308-disable_misaligned_probe_config-v9-0-a388770ba0ce@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Introduce Kconfig options to set the kernel unaligned access support.
These options provide a non-portable alternative to the runtime
unaligned access probe.
To support this, the unaligned access probing code is moved into it's
own file and gated behind a new RISCV_PROBE_UNALIGNED_ACCESS_SUPPORT
option.
Signed-off-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20240308-disable_misaligned_probe_config-v9-4-a388770ba0ce@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Detecting if a system traps into the kernel on an unaligned access
can be performed separately from checking the speed of unaligned
accesses. This decoupling will make it possible to selectively enable
or disable each of these checks.
Signed-off-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20240308-disable_misaligned_probe_config-v9-3-a388770ba0ce@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Create has_fast_unaligned_access to avoid needing to explicitly check
the fast_misaligned_access_speed_key static key.
Signed-off-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Evan Green <evan@rivosinc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20240308-disable_misaligned_probe_config-v9-1-a388770ba0ce@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Assign riscv_pmu_irq_num the value of (256 + 18) for the custome PMU
and add SSCOUNTOVF and SIP alternatives to ALT_SBI_PMU_OVERFLOW()
and ALT_SBI_PMU_OVF_CLEAR_PENDING() macros, respectively.
To make use of Andes PMU extension, "xandespmu" needs to be appended
to the riscv,isa-extensions for each cpu node in device-tree, and
make sure CONFIG_ANDES_CUSTOM_PMU is enabled.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Charles Ci-Jyun Wu <dminus@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Co-developed-by: Locus Wei-Han Chen <locus84@andestech.com>
Signed-off-by: Locus Wei-Han Chen <locus84@andestech.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240222083946.3977135-8-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Samuel Holland <samuel.holland@sifive.com> says:
This series fixes a couple of issues related to using the cbo.zero
instruction in userspace. The first patch fixes a bug where the wrong
enable bit gets set if the kernel is running in M-mode. The remaining
patches fix a bug where the enable bit gets reset to its default value
after a nonretentive idle state. I have hardware which reproduces this:
Before this series:
$ tools/testing/selftests/riscv/hwprobe/cbo
TAP version 13
1..3
ok 1 Zicboz block size
# Zicboz block size: 64
Illegal instruction
After applying this series:
$ tools/testing/selftests/riscv/hwprobe/cbo
TAP version 13
1..3
ok 1 Zicboz block size
# Zicboz block size: 64
ok 2 cbo.zero
ok 3 cbo.zero check
# Totals: pass:3 fail:0 xfail:0 xpass:0 skip:0 error:0
* b4-shazam-merge:
riscv: Save/restore envcfg CSR during CPU suspend
riscv: Add a custom ISA extension for the [ms]envcfg CSR
riscv: Fix enabling cbo.zero when running in M-mode
Link: https://lore.kernel.org/r/20240228065559.3434837-1-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The [ms]envcfg CSR was added in version 1.12 of the RISC-V privileged
ISA (aka S[ms]1p12). However, bits in this CSR are defined by several
other extensions which may be implemented separately from any particular
version of the privileged ISA (for example, some unrelated errata may
prevent an implementation from claiming conformance with Ss1p12). As a
result, Linux cannot simply use the privileged ISA version to determine
if the CSR is present. It must also check if any of these other
extensions are implemented. It also cannot probe the existence of the
CSR at runtime, because Linux does not require Sstrict, so (in the
absence of additional information) it cannot know if a CSR at that
address is [ms]envcfg or part of some non-conforming vendor extension.
Since there are several standard extensions that imply the existence of
the [ms]envcfg CSR, it becomes unwieldy to check for all of them
wherever the CSR is accessed. Instead, define a custom Xlinuxenvcfg ISA
extension bit that is implied by the other extensions and denotes that
the CSR exists as defined in the privileged ISA, containing at least one
of the fields common between menvcfg and senvcfg.
This extension does not need to be parsed from the devicetree or ISA
string because it can only be implemented as a subset of some other
standard extension.
Cc: <stable@vger.kernel.org> # v6.7+
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20240228065559.3434837-3-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
When the kernel is running in M-mode, the CBZE bit must be set in the
menvcfg CSR, not in senvcfg.
Cc: <stable@vger.kernel.org>
Fixes: 43c16d51a1 ("RISC-V: Enable cbo.zero in usermode")
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240228065559.3434837-2-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Before attempting to support the pre-ratification version of vector
found on older T-Head CPUs, disallow "v" in riscv,isa on these
platforms. The deprecated property has no clear way to communicate
the specific version of vector that is supported and much of the vendor
provided software puts "v" in the isa string. riscv,isa-extensions
should be used instead. This should not be too much of a burden for
these systems, as the vendor shipped devicetrees and firmware do not
work with a mainline kernel and will require updating.
We can limit this restriction to only ignore v in riscv,isa on CPUs
that report T-Head's vendor ID and a zero marchid. Newer T-Head CPUs
that support the ratified version of vector should report non-zero
marchid, according to Guo Ren [1].
Link: https://lore.kernel.org/linux-riscv/CAJF2gTRy5eK73=d6s7CVy9m9pB8p4rAoMHM3cZFwzg=AuF7TDA@mail.gmail.com/ [1]
Fixes: dc6667a4e7 ("riscv: Extending cpufeature.c to detect V-extension")
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20240223-tidings-shabby-607f086cb4d7@spud
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Charlie Jenkins <charlie@rivosinc.com> says:
Each architecture generally implements fine-tuned checksum functions to
leverage the instruction set. This patch adds the main checksum
functions that are used in networking. Tested on QEMU, this series
allows the CHECKSUM_KUNIT tests to complete an average of 50.9% faster.
This patch takes heavy use of the Zbb extension using alternatives
patching.
To test this patch, enable the configs for KUNIT, then CHECKSUM_KUNIT.
I have attempted to make these functions as optimal as possible, but I
have not ran anything on actual riscv hardware. My performance testing
has been limited to inspecting the assembly, running the algorithms on
x86 hardware, and running in QEMU.
ip_fast_csum is a relatively small function so even though it is
possible to read 64 bits at a time on compatible hardware, the
bottleneck becomes the clean up and setup code so loading 32 bits at a
time is actually faster.
* b4-shazam-merge:
kunit: Add tests for csum_ipv6_magic and ip_fast_csum
riscv: Add checksum library
riscv: Add checksum header
riscv: Add static key for misaligned accesses
asm-generic: Improve csum_fold
Link: https://lore.kernel.org/r/20240108-optimize_checksum-v15-0-1c50de5f2167@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Support static branches depending on the value of misaligned accesses.
This will be used by a later patch in the series. At any point in time,
this static branch will only be enabled if all online CPUs are
considered "fast".
Signed-off-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Evan Green <evan@rivosinc.com>
Link: https://lore.kernel.org/r/20240108-optimize_checksum-v15-2-1c50de5f2167@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Clément Léger <cleger@rivosinc.com> says:
This series add support for a few more extensions that are present in
the RVA22U64/RVA23U64 (either mandatory or optional) and that are useful
for userspace:
- Zicond
- Zacas
- Ztso
Series currently based on riscv/for-next.
* b4-shazam-lts:
riscv: hwprobe: export Zicond extension
riscv: hwprobe: export Zacas ISA extension
riscv: add ISA extension parsing for Zacas
dt-bindings: riscv: add Zacas ISA extension description
riscv: hwprobe: export Ztso ISA extension
riscv: add ISA extension parsing for Ztso
Link: https://lore.kernel.org/r/20231220155723.684081-1-cleger@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add support to parse the Ztso string in the riscv,isa string. The
bindings already supports it but not the ISA parsing code.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Link: https://lore.kernel.org/r/20231220155723.684081-2-cleger@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
There were a few single-letter extensions that we had references to
floating around in the kernel, but that never ended up as actual ISA
specs and have mostly been replaced by multi-letter extensions. This
removes the references to those extensions.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231110175903.2631-1-palmer@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The Scalar Crypto specification defines Zk as a shorthand for the
Zkn, Zkr and Zkt extensions. The same follows for both Zkn, Zks and Zbk,
which are all shorthands for various other extensions. The detailed
breakdown can be found in their dt-binding entries.
Since Zkn also implies the Zbkb, Zbkc and Zbkx extensions, simply passing
"zk" through a DT should enable all of Zbkb, Zbkc, Zbkx, Zkn, Zkr and Zkt.
For example, setting the "riscv,isa" DT property to "rv64imafdc_zk"
should generate the following cpuinfo output:
"rv64imafdc_zicntr_zicsr_zifencei_zihpm_zbkb_zbkc_zbkx_zknd_zkne_zknh_zkr_zkt"
riscv_isa_ext_data grows a pair of new members, to permit setting the
relevant bits for "bundled" extensions, both while parsing the ISA string
and the new dedicated extension properties.
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Evan Green <evan@rivosinc.com>
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231114141256.126749-4-cleger@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
* Support for handling misaligned accesses in S-mode.
* Probing for misaligned access support is now properly cached and
handled in parallel.
* PTDUMP now reflects the SW reserved bits, as well as the PBMT and
NAPOT extensions.
* Performance improvements for TLB flushing.
* Support for many new relocations in the module loader.
* Various bug fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEKzw3R0RoQ7JKlDp6LhMZ81+7GIkFAmVOUCcTHHBhbG1lckBk
YWJiZWx0LmNvbQAKCRAuExnzX7sYicJ2D/9S+9dnHYHVGTeJfr9Zf2T4r+qHBPyx
LXbTAbgHN6139MgcRLMRlcUaQ04RVxuBCWhxewJ6mQiHiYNlullgKmJO8oYMS4uZ
2yQGHKhzKEVluXxe+qT6VW+zsP0cY6pDQ+e59AqZgyWzvATxMU4VtFfCDdjFG03I
k/8Y3MUKSHAKzIHUsGHiMW5J2YRiM/iVehv2gZfanreulWlK6lyiV4AZ4KChu8Sa
gix9QkFJw+9+7RHnouHvczt4xTqLPJQcdecLJsbisEI4VaaPtTVzkvXx/kwbMwX0
qkQnZ7I60fPHrCb9ccuedjDMa1Z0lrfwRldBGz9f9QaW37Eppirn6LA5JiZ1cA47
wKTwba6gZJCTRXELFTJLcv+Cwdy003E0y3iL5UK2rkbLqcxfvLdq1WAJU2t05Lmh
aRQN10BtM2DZG+SNPlLoBpXPDw0Q3KOc20zGtuhmk010+X4yOK7WXlu8zNGLLE0+
yHamiZqAbpIUIEzwDdGbb95jywR1sUhNTbScuhj4Rc79ZqLtPxty1PUhnfqFat1R
i3ngQtCbeUUYFS2YV9tKkXjLf/xkQNRbt7kQBowuvFuvfksl9UwMdRAWcE/h0M9P
7uz7cBFhuG0v/XblB7bUhYLkKITvP+ltSMyxaGlfpGqCLAH2KIztdZ2PLWLRdKeU
+9dtZSQR6oBLqQ==
=NhdR
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.7-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- Support for handling misaligned accesses in S-mode
- Probing for misaligned access support is now properly cached and
handled in parallel
- PTDUMP now reflects the SW reserved bits, as well as the PBMT and
NAPOT extensions
- Performance improvements for TLB flushing
- Support for many new relocations in the module loader
- Various bug fixes and cleanups
* tag 'riscv-for-linus-6.7-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (51 commits)
riscv: Optimize bitops with Zbb extension
riscv: Rearrange hwcap.h and cpufeature.h
drivers: perf: Do not broadcast to other cpus when starting a counter
drivers: perf: Check find_first_bit() return value
of: property: Add fw_devlink support for msi-parent
RISC-V: Don't fail in riscv_of_parent_hartid() for disabled HARTs
riscv: Fix set_memory_XX() and set_direct_map_XX() by splitting huge linear mappings
riscv: Don't use PGD entries for the linear mapping
RISC-V: Probe misaligned access speed in parallel
RISC-V: Remove __init on unaligned_emulation_finish()
RISC-V: Show accurate per-hart isa in /proc/cpuinfo
RISC-V: Don't rely on positional structure initialization
riscv: Add tests for riscv module loading
riscv: Add remaining module relocations
riscv: Avoid unaligned access when relocating modules
riscv: split cache ops out of dma-noncoherent.c
riscv: Improve flush_tlb_kernel_range()
riscv: Make __flush_tlb_range() loop over pte instead of flushing the whole tlb
riscv: Improve flush_tlb_range() for hugetlb pages
riscv: Improve tlb_flush()
...
* Support for cbo.zero in userspace.
* Support for CBOs on ACPI-based systems.
* A handful of improvements for the T-Head cache flushing ops.
* Support for software shadow call stacks.
* Various cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=hKWl
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for cbo.zero in userspace
- Support for CBOs on ACPI-based systems
- A handful of improvements for the T-Head cache flushing ops
- Support for software shadow call stacks
- Various cleanups and fixes
* tag 'riscv-for-linus-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (31 commits)
RISC-V: hwprobe: Fix vDSO SIGSEGV
riscv: configs: defconfig: Enable configs required for RZ/Five SoC
riscv: errata: prefix T-Head mnemonics with th.
riscv: put interrupt entries into .irqentry.text
riscv: mm: Update the comment of CONFIG_PAGE_OFFSET
riscv: Using TOOLCHAIN_HAS_ZIHINTPAUSE marco replace zihintpause
riscv/mm: Fix the comment for swap pte format
RISC-V: clarify the QEMU workaround in ISA parser
riscv: correct pt_level name via pgtable_l5/4_enabled
RISC-V: Provide pgtable_l5_enabled on rv32
clocksource: timer-riscv: Increase rating of clock_event_device for Sstc
clocksource: timer-riscv: Don't enable/disable timer interrupt
lkdtm: Fix CFI_BACKWARD on RISC-V
riscv: Use separate IRQ shadow call stacks
riscv: Implement Shadow Call Stack
riscv: Move global pointer loading to a macro
riscv: Deduplicate IRQ stack switching
riscv: VMAP_STACK overflow detection thread-safe
RISC-V: cacheflush: Initialize CBO variables on ACPI systems
RISC-V: ACPI: RHCT: Add function to get CBO block sizes
...
Probing for misaligned access speed takes about 0.06 seconds. On a
system with 64 cores, doing this in smp_callin() means it's done
serially, extending boot time by 3.8 seconds. That's a lot of boot time.
Instead of measuring each CPU serially, let's do the measurements on
all CPUs in parallel. If we disable preemption on all CPUs, the
jiffies stop ticking, so we can do this in stages of 1) everybody
except core 0, then 2) core 0. The allocations are all done outside of
on_each_cpu() to avoid calling alloc_pages() with interrupts disabled.
For hotplugged CPUs that come in after the boot time measurement,
register CPU hotplug callbacks, and do the measurement there. Interrupts
are enabled in those callbacks, so they're fine to do alloc_pages() in.
Reported-by: Jisheng Zhang <jszhang@kernel.org>
Closes: https://lore.kernel.org/all/mhng-9359993d-6872-4134-83ce-c97debe1cf9a@palmer-ri-x1c9/T/#mae9b8f40016f9df428829d33360144dc5026bcbf
Fixes: 584ea6564b ("RISC-V: Probe for unaligned access speed")
Signed-off-by: Evan Green <evan@rivosinc.com>
Link: https://lore.kernel.org/r/20231106225855.3121724-1-evan@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
If misaligned_access_speed percpu var isn't so called "HWPROBE
MISALIGNED UNKNOWN", it means the probe has happened(this is possible
for example, hotplug off then hotplug on one cpu), and the percpu var
has been set, don't probe again in this case.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Fixes: 584ea6564b ("RISC-V: Probe for unaligned access speed")
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230912154040.3306-1-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Clément Léger <cleger@rivosinc.com> says:
Since commit 61cadb9 ("Provide new description of misaligned load/store
behavior compatible with privileged architecture.") in the RISC-V ISA
manual, it is stated that misaligned load/store might not be supported.
However, the RISC-V kernel uABI describes that misaligned accesses are
supported. In order to support that, this series adds support for S-mode
handling of misaligned accesses as well support for prctl(PR_UNALIGN).
Handling misaligned access in kernel allows for a finer grain control
of the misaligned accesses behavior, and thanks to the prctl() call,
can allow disabling misaligned access emulation to generate SIGBUS. User
space can then optimize its software by removing such access based on
SIGBUS generation.
This series is useful when using a SBI implementation that does not
handle misaligned traps as well as detecting misaligned accesses
generated by userspace application using the prctrl(PR_SET_UNALIGN)
feature.
This series can be tested using the spike simulator[1] and a modified
openSBI version[2] which allows to always delegate misaligned load/store to
S-mode. A test[3] that exercise various instructions/registers can be
executed to verify the unaligned access support.
[1] https://github.com/riscv-software-src/riscv-isa-sim
[2] https://github.com/rivosinc/opensbi/tree/dev/cleger/no_misaligned
[3] https://github.com/clementleger/unaligned_test
* b4-shazam-merge:
riscv: add support for PR_SET_UNALIGN and PR_GET_UNALIGN
riscv: report misaligned accesses emulation to hwprobe
riscv: annotate check_unaligned_access_boot_cpu() with __init
riscv: add support for sysctl unaligned_enabled control
riscv: add floating point insn support to misaligned access emulation
riscv: report perf event for misaligned fault
riscv: add support for misaligned trap handling in S-mode
riscv: remove unused functions in traps_misaligned.c
Link: https://lore.kernel.org/r/20231004151405.521596-1-cleger@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
hwprobe provides a way to report if misaligned access are emulated. In
order to correctly populate that feature, we can check if it actually
traps when doing a misaligned access. This can be checked using an
exception table entry which will actually be used when a misaligned
access is done from kernel mode.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Link: https://lore.kernel.org/r/20231004151405.521596-8-cleger@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
This function is solely called as an initcall, thus annotate it with
__init.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Evan Green <evan@rivosinc.com>
Link: https://lore.kernel.org/r/20231004151405.521596-7-cleger@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Extensions prefixed with "Su" won't corrupt the workaround in many
cases. The only exception is when the first multi-letter extension in the
ISA string begins with "Su" and is not prefixed with an underscore.
For instance, following ISA string can confuse this QEMU workaround.
* "rv64imacsuclic" (RV64I + M + A + C + "Suclic")
However, this case is very unlikely because extensions prefixed by either
"Z", "Sm" or "Ss" will most likely precede first.
For instance, the "Suclic" extension (draft as of now) will be placed after
related "Smclic" and "Ssclic" extensions. It's also highly likely that
other unprivileged extensions like "Zba" will precede.
It's also possible to suppress the issue in the QEMU workaround with an
underscore. Following ISA string won't confuse the QEMU workaround.
* "rv64imac_suclic" (RV64I + M + A + C + delimited "Suclic")
This fix is to tell kernel developers the nature of this workaround
precisely. There are some "Su*" extensions to be ratified but don't worry
about this workaround too much.
This commit comes with other minor editorial fixes (for minor wording and
spacing issues, without changing the meaning).
Signed-off-by: Tsukasa OI <research_trasio@irq.a4lg.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/8a127608cf6194a6d288289f2520bd1744b81437.1690350252.git.research_trasio@irq.a4lg.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The RISC-V integer conditional (Zicond) operation extension defines
standard conditional arithmetic and conditional-select/move operations
which are inspired from the XVentanaCondOps extension. In fact, QEMU
RISC-V also has support for emulating Zicond extension.
Let us detect Zicond extension from ISA string available through
DT or ACPI.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Extend the ISA string parsing to detect the Smstateen extension. If the
extension is enabled then access to certain 'state' such as AIA CSRs in
VS mode is controlled by *stateen0 registers.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
When Zicboz is present, enable its instruction (cbo.zero) in
usermode by setting its respective senvcfg bit. We don't bother
trying to set this bit per-task, which would also require an
interface for tasks to request enabling and/or disabling. Instead,
permanently set the bit for each hart which has the extension when
bringing it online.
This patch also introduces riscv_cpu_has_extension_[un]likely()
functions to check a specific hart's ISA bitmap for extensions.
Prior to checking the specific hart's bitmap in these functions
we try the bitmap which represents the LCD of extensions, but only
when we know it will use its optimized, alternatives path by gating
its call on CONFIG_RISCV_ALTERNATIVE. When alternatives are used, the
compiler ensures that the invocation of the LCD search becomes a
constant true or false. When it's true, even the new functions will
completely vanish from their callsites. OTOH, when the LCD check is
false, we need to do a search of the hart's ISA bitmap. Had we also
checked the LCD bitmap without the use of alternatives, then we would
have ended up with two bitmap searches instead of one.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230918131518.56803-10-ajones@ventanamicro.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
commit c818fea83d ("riscv: say disabling zicbom if no or bad
riscv,cbom-block-size found") improved the error messages for
zicbom but zicboz was missed since its patches were in flight
at the same time. Get 'em now.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230918131518.56803-9-ajones@ventanamicro.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Evan Green <evan@rivosinc.com> says:
The current setting for the hwprobe bit indicating misaligned access
speed is controlled by a vendor-specific feature probe function. This is
essentially a per-SoC table we have to maintain on behalf of each vendor
going forward. Let's convert that instead to something we detect at
runtime.
We have two assembly routines at the heart of our probe: one that
does a bunch of word-sized accesses (without aligning its input buffer),
and the other that does byte accesses. If we can move a larger number of
bytes using misaligned word accesses than we can with the same amount of
time doing byte accesses, then we can declare misaligned accesses as
"fast".
The tradeoff of reducing this maintenance burden is boot time. We spend
4-6 jiffies per core doing this measurement (0-2 on jiffie edge
alignment, and 4 on measurement). The timing loop was based on
raid6_choose_gen(), which uses (16+1)*N jiffies (where N is the number
of algorithms). By taking only the fastest iteration out of all
attempts for use in the comparison, variance between runs is very low.
On my THead C906, it looks like this:
[ 0.047563] cpu0: Ratio of byte access time to unaligned word access is 4.34, unaligned accesses are fast
Several others have chimed in with results on slow machines with the
older algorithm, which took all runs into account, including noise like
interrupts. Even with this variation, results indicate that in all cases
(fast, slow, and emulated) the measured numbers are nowhere near each
other (always multiple factors away).
* b4-shazam-merge:
RISC-V: alternative: Remove feature_probe_func
RISC-V: Probe for unaligned access speed
Link: https://lore.kernel.org/r/20230818194136.4084400-1-evan@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
