There are two distinct CPU features related to the use of XSAVES and LBR:
whether LBR is itself supported and whether XSAVES supports LBR. The LBR
subsystem correctly checks both in intel_pmu_arch_lbr_init(), but the
XSTATE subsystem does not.
The LBR bit is only removed from xfeatures_mask_independent when LBR is not
supported by the CPU, but there is no validation of XSTATE support.
If XSAVES does not support LBR the write to IA32_XSS causes a #GP fault,
leaving the state of IA32_XSS unchanged, i.e. zero. The fault is handled
with a warning and the boot continues.
Consequently the next XRSTORS which tries to restore supervisor state fails
with #GP because the RFBM has zero for all supervisor features, which does
not match the XCOMP_BV field.
As XFEATURE_MASK_FPSTATE includes supervisor features setting up the FPU
causes a #GP, which ends up in fpu_reset_from_exception_fixup(). That fails
due to the same problem resulting in recursive #GPs until the kernel runs
out of stack space and double faults.
Prevent this by storing the supported independent features in
fpu_kernel_cfg during XSTATE initialization and use that cached value for
retrieving the independent feature bits to be written into IA32_XSS.
[ tglx: Massaged change log ]
Fixes: f0dccc9da4 ("x86/fpu/xstate: Support dynamic supervisor feature for LBR")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Mitchell Levy <levymitchell0@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240812-xsave-lbr-fix-v3-1-95bac1bf62f4@gmail.com
* Move a lot of state that was previously stored on a per vcpu
basis into a per-CPU area, because it is only pertinent to the
host while the vcpu is loaded. This results in better state
tracking, and a smaller vcpu structure.
* Add full handling of the ERET/ERETAA/ERETAB instructions in
nested virtualisation. The last two instructions also require
emulating part of the pointer authentication extension.
As a result, the trap handling of pointer authentication has
been greatly simplified.
* Turn the global (and not very scalable) LPI translation cache
into a per-ITS, scalable cache, making non directly injected
LPIs much cheaper to make visible to the vcpu.
* A batch of pKVM patches, mostly fixes and cleanups, as the
upstreaming process seems to be resuming. Fingers crossed!
* Allocate PPIs and SGIs outside of the vcpu structure, allowing
for smaller EL2 mapping and some flexibility in implementing
more or less than 32 private IRQs.
* Purge stale mpidr_data if a vcpu is created after the MPIDR
map has been created.
* Preserve vcpu-specific ID registers across a vcpu reset.
* Various minor cleanups and improvements.
LoongArch:
* Add ParaVirt IPI support.
* Add software breakpoint support.
* Add mmio trace events support.
RISC-V:
* Support guest breakpoints using ebreak
* Introduce per-VCPU mp_state_lock and reset_cntx_lock
* Virtualize SBI PMU snapshot and counter overflow interrupts
* New selftests for SBI PMU and Guest ebreak
* Some preparatory work for both TDX and SNP page fault handling.
This also cleans up the page fault path, so that the priorities
of various kinds of fauls (private page, no memory, write
to read-only slot, etc.) are easier to follow.
x86:
* Minimize amount of time that shadow PTEs remain in the special
REMOVED_SPTE state. This is a state where the mmu_lock is held for
reading but concurrent accesses to the PTE have to spin; shortening
its use allows other vCPUs to repopulate the zapped region while
the zapper finishes tearing down the old, defunct page tables.
* Advertise the max mappable GPA in the "guest MAXPHYADDR" CPUID field,
which is defined by hardware but left for software use. This lets KVM
communicate its inability to map GPAs that set bits 51:48 on hosts
without 5-level nested page tables. Guest firmware is expected to
use the information when mapping BARs; this avoids that they end up at
a legal, but unmappable, GPA.
* Fixed a bug where KVM would not reject accesses to MSR that aren't
supposed to exist given the vCPU model and/or KVM configuration.
* As usual, a bunch of code cleanups.
x86 (AMD):
* Implement a new and improved API to initialize SEV and SEV-ES VMs, which
will also be extendable to SEV-SNP. The new API specifies the desired
encryption in KVM_CREATE_VM and then separately initializes the VM.
The new API also allows customizing the desired set of VMSA features;
the features affect the measurement of the VM's initial state, and
therefore enabling them cannot be done tout court by the hypervisor.
While at it, the new API includes two bugfixes that couldn't be
applied to the old one without a flag day in userspace or without
affecting the initial measurement. When a SEV-ES VM is created with
the new VM type, KVM_GET_REGS/KVM_SET_REGS and friends are
rejected once the VMSA has been encrypted. Also, the FPU and AVX
state will be synchronized and encrypted too.
* Support for GHCB version 2 as applicable to SEV-ES guests. This, once
more, is only accessible when using the new KVM_SEV_INIT2 flow for
initialization of SEV-ES VMs.
x86 (Intel):
* An initial bunch of prerequisite patches for Intel TDX were merged.
They generally don't do anything interesting. The only somewhat user
visible change is a new debugging mode that checks that KVM's MMU
never triggers a #VE virtualization exception in the guest.
* Clear vmcs.EXIT_QUALIFICATION when synthesizing an EPT Misconfig VM-Exit to
L1, as per the SDM.
Generic:
* Use vfree() instead of kvfree() for allocations that always use vcalloc()
or __vcalloc().
* Remove .change_pte() MMU notifier - the changes to non-KVM code are
small and Andrew Morton asked that I also take those through the KVM
tree. The callback was only ever implemented by KVM (which was also the
original user of MMU notifiers) but it had been nonfunctional ever since
calls to set_pte_at_notify were wrapped with invalidate_range_start
and invalidate_range_end... in 2012.
Selftests:
* Enhance the demand paging test to allow for better reporting and stressing
of UFFD performance.
* Convert the steal time test to generate TAP-friendly output.
* Fix a flaky false positive in the xen_shinfo_test due to comparing elapsed
time across two different clock domains.
* Skip the MONITOR/MWAIT test if the host doesn't actually support MWAIT.
* Avoid unnecessary use of "sudo" in the NX hugepage test wrapper shell
script, to play nice with running in a minimal userspace environment.
* Allow skipping the RSEQ test's sanity check that the vCPU was able to
complete a reasonable number of KVM_RUNs, as the assert can fail on a
completely valid setup. If the test is run on a large-ish system that is
otherwise idle, and the test isn't affined to a low-ish number of CPUs, the
vCPU task can be repeatedly migrated to CPUs that are in deep sleep states,
which results in the vCPU having very little net runtime before the next
migration due to high wakeup latencies.
* Define _GNU_SOURCE for all selftests to fix a warning that was introduced by
a change to kselftest_harness.h late in the 6.9 cycle, and because forcing
every test to #define _GNU_SOURCE is painful.
* Provide a global pseudo-RNG instance for all tests, so that library code can
generate random, but determinstic numbers.
* Use the global pRNG to randomly force emulation of select writes from guest
code on x86, e.g. to help validate KVM's emulation of locked accesses.
* Allocate and initialize x86's GDT, IDT, TSS, segments, and default exception
handlers at VM creation, instead of forcing tests to manually trigger the
related setup.
Documentation:
* Fix a goof in the KVM_CREATE_GUEST_MEMFD documentation.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmZE878UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOukQf+LcvZsWtrC7Wd5K9SQbYXaS4Rk6P6
JHoQW2d0hUN893J2WibEw+l1J/0vn5JumqHXyZgJ7CbaMtXkWWQTwDSDLuURUKpv
XNB3Sb17G87NH+s1tOh0tA9h5upbtlHVHvrtIwdbb9+XHgQ6HTL4uk+HdfO/p9fW
cWBEZAKoWcCIa99Numv3pmq5vdrvBlNggwBugBS8TH69EKMw+V1Vu1SFkIdNDTQk
NJJ28cohoP3wnwlIHaXSmU4RujipPH3Lm/xupyA5MwmzO713eq2yUqV49jzhD5/I
MA4Ruvgrdm4wpp89N9lQMyci91u6q7R9iZfMu0tSg2qYI3UPKIdstd8sOA==
=2lED
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- Move a lot of state that was previously stored on a per vcpu basis
into a per-CPU area, because it is only pertinent to the host while
the vcpu is loaded. This results in better state tracking, and a
smaller vcpu structure.
- Add full handling of the ERET/ERETAA/ERETAB instructions in nested
virtualisation. The last two instructions also require emulating
part of the pointer authentication extension. As a result, the trap
handling of pointer authentication has been greatly simplified.
- Turn the global (and not very scalable) LPI translation cache into
a per-ITS, scalable cache, making non directly injected LPIs much
cheaper to make visible to the vcpu.
- A batch of pKVM patches, mostly fixes and cleanups, as the
upstreaming process seems to be resuming. Fingers crossed!
- Allocate PPIs and SGIs outside of the vcpu structure, allowing for
smaller EL2 mapping and some flexibility in implementing more or
less than 32 private IRQs.
- Purge stale mpidr_data if a vcpu is created after the MPIDR map has
been created.
- Preserve vcpu-specific ID registers across a vcpu reset.
- Various minor cleanups and improvements.
LoongArch:
- Add ParaVirt IPI support
- Add software breakpoint support
- Add mmio trace events support
RISC-V:
- Support guest breakpoints using ebreak
- Introduce per-VCPU mp_state_lock and reset_cntx_lock
- Virtualize SBI PMU snapshot and counter overflow interrupts
- New selftests for SBI PMU and Guest ebreak
- Some preparatory work for both TDX and SNP page fault handling.
This also cleans up the page fault path, so that the priorities of
various kinds of fauls (private page, no memory, write to read-only
slot, etc.) are easier to follow.
x86:
- Minimize amount of time that shadow PTEs remain in the special
REMOVED_SPTE state.
This is a state where the mmu_lock is held for reading but
concurrent accesses to the PTE have to spin; shortening its use
allows other vCPUs to repopulate the zapped region while the zapper
finishes tearing down the old, defunct page tables.
- Advertise the max mappable GPA in the "guest MAXPHYADDR" CPUID
field, which is defined by hardware but left for software use.
This lets KVM communicate its inability to map GPAs that set bits
51:48 on hosts without 5-level nested page tables. Guest firmware
is expected to use the information when mapping BARs; this avoids
that they end up at a legal, but unmappable, GPA.
- Fixed a bug where KVM would not reject accesses to MSR that aren't
supposed to exist given the vCPU model and/or KVM configuration.
- As usual, a bunch of code cleanups.
x86 (AMD):
- Implement a new and improved API to initialize SEV and SEV-ES VMs,
which will also be extendable to SEV-SNP.
The new API specifies the desired encryption in KVM_CREATE_VM and
then separately initializes the VM. The new API also allows
customizing the desired set of VMSA features; the features affect
the measurement of the VM's initial state, and therefore enabling
them cannot be done tout court by the hypervisor.
While at it, the new API includes two bugfixes that couldn't be
applied to the old one without a flag day in userspace or without
affecting the initial measurement. When a SEV-ES VM is created with
the new VM type, KVM_GET_REGS/KVM_SET_REGS and friends are rejected
once the VMSA has been encrypted. Also, the FPU and AVX state will
be synchronized and encrypted too.
- Support for GHCB version 2 as applicable to SEV-ES guests.
This, once more, is only accessible when using the new
KVM_SEV_INIT2 flow for initialization of SEV-ES VMs.
x86 (Intel):
- An initial bunch of prerequisite patches for Intel TDX were merged.
They generally don't do anything interesting. The only somewhat
user visible change is a new debugging mode that checks that KVM's
MMU never triggers a #VE virtualization exception in the guest.
- Clear vmcs.EXIT_QUALIFICATION when synthesizing an EPT Misconfig
VM-Exit to L1, as per the SDM.
Generic:
- Use vfree() instead of kvfree() for allocations that always use
vcalloc() or __vcalloc().
- Remove .change_pte() MMU notifier - the changes to non-KVM code are
small and Andrew Morton asked that I also take those through the
KVM tree.
The callback was only ever implemented by KVM (which was also the
original user of MMU notifiers) but it had been nonfunctional ever
since calls to set_pte_at_notify were wrapped with
invalidate_range_start and invalidate_range_end... in 2012.
Selftests:
- Enhance the demand paging test to allow for better reporting and
stressing of UFFD performance.
- Convert the steal time test to generate TAP-friendly output.
- Fix a flaky false positive in the xen_shinfo_test due to comparing
elapsed time across two different clock domains.
- Skip the MONITOR/MWAIT test if the host doesn't actually support
MWAIT.
- Avoid unnecessary use of "sudo" in the NX hugepage test wrapper
shell script, to play nice with running in a minimal userspace
environment.
- Allow skipping the RSEQ test's sanity check that the vCPU was able
to complete a reasonable number of KVM_RUNs, as the assert can fail
on a completely valid setup.
If the test is run on a large-ish system that is otherwise idle,
and the test isn't affined to a low-ish number of CPUs, the vCPU
task can be repeatedly migrated to CPUs that are in deep sleep
states, which results in the vCPU having very little net runtime
before the next migration due to high wakeup latencies.
- Define _GNU_SOURCE for all selftests to fix a warning that was
introduced by a change to kselftest_harness.h late in the 6.9
cycle, and because forcing every test to #define _GNU_SOURCE is
painful.
- Provide a global pseudo-RNG instance for all tests, so that library
code can generate random, but determinstic numbers.
- Use the global pRNG to randomly force emulation of select writes
from guest code on x86, e.g. to help validate KVM's emulation of
locked accesses.
- Allocate and initialize x86's GDT, IDT, TSS, segments, and default
exception handlers at VM creation, instead of forcing tests to
manually trigger the related setup.
Documentation:
- Fix a goof in the KVM_CREATE_GUEST_MEMFD documentation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (225 commits)
selftests/kvm: remove dead file
KVM: selftests: arm64: Test vCPU-scoped feature ID registers
KVM: selftests: arm64: Test that feature ID regs survive a reset
KVM: selftests: arm64: Store expected register value in set_id_regs
KVM: selftests: arm64: Rename helper in set_id_regs to imply VM scope
KVM: arm64: Only reset vCPU-scoped feature ID regs once
KVM: arm64: Reset VM feature ID regs from kvm_reset_sys_regs()
KVM: arm64: Rename is_id_reg() to imply VM scope
KVM: arm64: Destroy mpidr_data for 'late' vCPU creation
KVM: arm64: Use hVHE in pKVM by default on CPUs with VHE support
KVM: arm64: Fix hvhe/nvhe early alias parsing
KVM: SEV: Allow per-guest configuration of GHCB protocol version
KVM: SEV: Add GHCB handling for termination requests
KVM: SEV: Add GHCB handling for Hypervisor Feature Support requests
KVM: SEV: Add support to handle AP reset MSR protocol
KVM: x86: Explicitly zero kvm_caps during vendor module load
KVM: x86: Fully re-initialize supported_mce_cap on vendor module load
KVM: x86: Fully re-initialize supported_vm_types on vendor module load
KVM: x86/mmu: Sanity check that __kvm_faultin_pfn() doesn't create noslot pfns
KVM: x86/mmu: Initialize kvm_page_fault's pfn and hva to error values
...
- Fix asm() constraints & modifiers in restore_fpregs_from_fpstate()
- Update comments
- Robustify the free_vm86() definition
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=PO9v
-----END PGP SIGNATURE-----
Merge tag 'x86-fpu-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fpu updates from Ingo Molnar:
- Fix asm() constraints & modifiers in restore_fpregs_from_fpstate()
- Update comments
- Robustify the free_vm86() definition
* tag 'x86-fpu-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Update fpu_swap_kvm_fpu() uses in comments as well
x86/vm86: Make sure the free_vm86(task) definition uses its parameter even in the !CONFIG_VM86 case
x86/fpu: Fix AMD X86_BUG_FXSAVE_LEAK fixup
SEV-ES allows passing custom contents for x87, SSE and AVX state into the VMSA.
Allow userspace to do that with the usual KVM_SET_XSAVE API and only mark
FPU contents as confidential after it has been copied and encrypted into
the VMSA.
Since the XSAVE state for AVX is the first, it does not need the
compacted-state handling of get_xsave_addr(). However, there are other
parts of XSAVE state in the VMSA that currently are not handled, and
the validation logic of get_xsave_addr() is pointless to duplicate
in KVM, so move get_xsave_addr() to public FPU API; it is really just
a facility to operate on XSAVE state and does not expose any internal
details of arch/x86/kernel/fpu.
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20240404121327.3107131-12-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The following commit:
d69c1382e1 ("x86/kvm: Convert FPU handling to a single swap buffer")
reworked KVM FPU handling, but forgot to update the comments
in xstate_op_valid(): fpu_swap_kvm_fpu() doesn't exist anymore,
fpu_swap_kvm_fpstate() is used instead.
Update the comments accordingly.
[ mingo: Improved the changelog. ]
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240403091803.818-1-lirongqing@baidu.com
Commit 672365477a ("x86/fpu: Update XFD state where required") and
commit 8bf26758ca ("x86/fpu: Add XFD state to fpstate") introduced a
per CPU variable xfd_state to keep the MSR_IA32_XFD value cached, in
order to avoid unnecessary writes to the MSR.
On CPU hotplug MSR_IA32_XFD is reset to the init_fpstate.xfd, which
wipes out any stale state. But the per CPU cached xfd value is not
reset, which brings them out of sync.
As a consequence a subsequent xfd_update_state() might fail to update
the MSR which in turn can result in XRSTOR raising a #NM in kernel
space, which crashes the kernel.
To fix this, introduce xfd_set_state() to write xfd_state together
with MSR_IA32_XFD, and use it in all places that set MSR_IA32_XFD.
Fixes: 672365477a ("x86/fpu: Update XFD state where required")
Signed-off-by: Adamos Ttofari <attofari@amazon.de>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240322230439.456571-1-chang.seok.bae@intel.com
Closes: https://lore.kernel.org/lkml/20230511152818.13839-1-attofari@amazon.de
Mask off xfeatures that aren't exposed to the guest only when saving guest
state via KVM_GET_XSAVE{2} instead of modifying user_xfeatures directly.
Preserving the maximal set of xfeatures in user_xfeatures restores KVM's
ABI for KVM_SET_XSAVE, which prior to commit ad856280dd ("x86/kvm/fpu:
Limit guest user_xfeatures to supported bits of XCR0") allowed userspace
to load xfeatures that are supported by the host, irrespective of what
xfeatures are exposed to the guest.
There is no known use case where userspace *intentionally* loads xfeatures
that aren't exposed to the guest, but the bug fixed by commit ad856280dd
was specifically that KVM_GET_SAVE{2} would save xfeatures that weren't
exposed to the guest, e.g. would lead to userspace unintentionally loading
guest-unsupported xfeatures when live migrating a VM.
Restricting KVM_SET_XSAVE to guest-supported xfeatures is especially
problematic for QEMU-based setups, as QEMU has a bug where instead of
terminating the VM if KVM_SET_XSAVE fails, QEMU instead simply stops
loading guest state, i.e. resumes the guest after live migration with
incomplete guest state, and ultimately results in guest data corruption.
Note, letting userspace restore all host-supported xfeatures does not fix
setups where a VM is migrated from a host *without* commit ad856280dd,
to a target with a subset of host-supported xfeatures. However there is
no way to safely address that scenario, e.g. KVM could silently drop the
unsupported features, but that would be a clear violation of KVM's ABI and
so would require userspace to opt-in, at which point userspace could
simply be updated to sanitize the to-be-loaded XSAVE state.
Reported-by: Tyler Stachecki <stachecki.tyler@gmail.com>
Closes: https://lore.kernel.org/all/20230914010003.358162-1-tstachecki@bloomberg.net
Fixes: ad856280dd ("x86/kvm/fpu: Limit guest user_xfeatures to supported bits of XCR0")
Cc: stable@vger.kernel.org
Cc: Leonardo Bras <leobras@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Message-Id: <20230928001956.924301-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Plumb an xfeatures mask into __copy_xstate_to_uabi_buf() so that KVM can
constrain which xfeatures are saved into the userspace buffer without
having to modify the user_xfeatures field in KVM's guest_fpu state.
KVM's ABI for KVM_GET_XSAVE{2} is that features that are not exposed to
guest must not show up in the effective xstate_bv field of the buffer.
Saving only the guest-supported xfeatures allows userspace to load the
saved state on a different host with a fewer xfeatures, so long as the
target host supports the xfeatures that are exposed to the guest.
KVM currently sets user_xfeatures directly to restrict KVM_GET_XSAVE{2} to
the set of guest-supported xfeatures, but doing so broke KVM's historical
ABI for KVM_SET_XSAVE, which allows userspace to load any xfeatures that
are supported by the *host*.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230928001956.924301-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Fix PKRU covert channel
* Fix -Wmissing-variable-declarations warning for ia32_xyz_class
* Fix kernel-doc annotation warning
-----BEGIN PGP SIGNATURE-----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=prt2
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2023-09-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Dave Hansen:
"The most important fix here adds a missing CPU model to the recent
Gather Data Sampling (GDS) mitigation list to ensure that mitigations
are available on that CPU.
There are also a pair of warning fixes, and closure of a covert
channel that pops up when protection keys are disabled.
Summary:
- Mark all Skylake CPUs as vulnerable to GDS
- Fix PKRU covert channel
- Fix -Wmissing-variable-declarations warning for ia32_xyz_class
- Fix kernel-doc annotation warning"
* tag 'x86-urgent-2023-09-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu/xstate: Fix PKRU covert channel
x86/irq/i8259: Fix kernel-doc annotation warning
x86/speculation: Mark all Skylake CPUs as vulnerable to GDS
x86/audit: Fix -Wmissing-variable-declarations warning for ia32_xyz_class
When XCR0[9] is set, PKRU can be read and written from userspace with
XSAVE and XRSTOR, even when CR4.PKE is clear.
Clear XCR0[9] when protection keys are disabled.
Reported-by: Tavis Ormandy <taviso@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20230831043228.1194256-1-jmattson@google.com
Convert IBT selftest to asm to fix objtool warning
-----BEGIN PGP SIGNATURE-----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=3UUm
-----END PGP SIGNATURE-----
Merge tag 'x86_shstk_for_6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 shadow stack support from Dave Hansen:
"This is the long awaited x86 shadow stack support, part of Intel's
Control-flow Enforcement Technology (CET).
CET consists of two related security features: shadow stacks and
indirect branch tracking. This series implements just the shadow stack
part of this feature, and just for userspace.
The main use case for shadow stack is providing protection against
return oriented programming attacks. It works by maintaining a
secondary (shadow) stack using a special memory type that has
protections against modification. When executing a CALL instruction,
the processor pushes the return address to both the normal stack and
to the special permission shadow stack. Upon RET, the processor pops
the shadow stack copy and compares it to the normal stack copy.
For more information, refer to the links below for the earlier
versions of this patch set"
Link: https://lore.kernel.org/lkml/20220130211838.8382-1-rick.p.edgecombe@intel.com/
Link: https://lore.kernel.org/lkml/20230613001108.3040476-1-rick.p.edgecombe@intel.com/
* tag 'x86_shstk_for_6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (47 commits)
x86/shstk: Change order of __user in type
x86/ibt: Convert IBT selftest to asm
x86/shstk: Don't retry vm_munmap() on -EINTR
x86/kbuild: Fix Documentation/ reference
x86/shstk: Move arch detail comment out of core mm
x86/shstk: Add ARCH_SHSTK_STATUS
x86/shstk: Add ARCH_SHSTK_UNLOCK
x86: Add PTRACE interface for shadow stack
selftests/x86: Add shadow stack test
x86/cpufeatures: Enable CET CR4 bit for shadow stack
x86/shstk: Wire in shadow stack interface
x86: Expose thread features in /proc/$PID/status
x86/shstk: Support WRSS for userspace
x86/shstk: Introduce map_shadow_stack syscall
x86/shstk: Check that signal frame is shadow stack mem
x86/shstk: Check that SSP is aligned on sigreturn
x86/shstk: Handle signals for shadow stack
x86/shstk: Introduce routines modifying shstk
x86/shstk: Handle thread shadow stack
x86/shstk: Add user-mode shadow stack support
...
0-Day found a 34.6% regression in stress-ng's 'af-alg' test case, and
bisected it to commit b81fac906a ("x86/fpu: Move FPU initialization into
arch_cpu_finalize_init()"), which optimizes the FPU init order, and moves
the CR4_OSXSAVE enabling into a later place:
arch_cpu_finalize_init
identify_boot_cpu
identify_cpu
generic_identify
get_cpu_cap --> setup cpu capability
...
fpu__init_cpu
fpu__init_cpu_xstate
cr4_set_bits(X86_CR4_OSXSAVE);
As the FPU is not yet initialized the CPU capability setup fails to set
X86_FEATURE_OSXSAVE. Many security module like 'camellia_aesni_avx_x86_64'
depend on this feature and therefore fail to load, causing the regression.
Cure this by setting X86_FEATURE_OSXSAVE feature right after OSXSAVE
enabling.
[ tglx: Moved it into the actual BSP FPU initialization code and added a comment ]
Fixes: b81fac906a ("x86/fpu: Move FPU initialization into arch_cpu_finalize_init()")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/202307192135.203ac24e-oliver.sang@intel.com
Link: https://lore.kernel.org/lkml/20230823065747.92257-1-feng.tang@intel.com
Shadow stack register state can be managed with XSAVE. The registers
can logically be separated into two groups:
* Registers controlling user-mode operation
* Registers controlling kernel-mode operation
The architecture has two new XSAVE state components: one for each group
of those groups of registers. This lets an OS manage them separately if
it chooses. Future patches for host userspace and KVM guests will only
utilize the user-mode registers, so only configure XSAVE to save
user-mode registers. This state will add 16 bytes to the xsave buffer
size.
Future patches will use the user-mode XSAVE area to save guest user-mode
CET state. However, VMCS includes new fields for guest CET supervisor
states. KVM can use these to save and restore guest supervisor state, so
host supervisor XSAVE support is not required.
Adding this exacerbates the already unwieldy if statement in
check_xstate_against_struct() that handles warning about unimplemented
xfeatures. So refactor these check's by having XCHECK_SZ() set a bool when
it actually check's the xfeature. This ends up exceeding 80 chars, but was
better on balance than other options explored. Pass the bool as pointer to
make it clear that XCHECK_SZ() can change the variable.
While configuring user-mode XSAVE, clarify kernel-mode registers are not
managed by XSAVE by defining the xfeature in
XFEATURE_MASK_SUPERVISOR_UNSUPPORTED, like is done for XFEATURE_MASK_PT.
This serves more of a documentation as code purpose, and functionally,
only enables a few safety checks.
Both XSAVE state components are supervisor states, even the state
controlling user-mode operation. This is a departure from earlier features
like protection keys where the PKRU state is a normal user
(non-supervisor) state. Having the user state be supervisor-managed
ensures there is no direct, unprivileged access to it, making it harder
for an attacker to subvert CET.
To facilitate this privileged access, define the two user-mode CET MSRs,
and the bits defined in those MSRs relevant to future shadow stack
enablement patches.
Co-developed-by: Yu-cheng Yu <yu-cheng.yu@intel.com>
Signed-off-by: Yu-cheng Yu <yu-cheng.yu@intel.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Tested-by: John Allen <john.allen@amd.com>
Tested-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/all/20230613001108.3040476-25-rick.p.edgecombe%40intel.com
__copy_xstate_to_uabi_buf() copies either from the tasks XSAVE buffer
or from init_fpstate into the ptrace buffer. Dynamic features, like
XTILEDATA, have an all zeroes init state and are not saved in
init_fpstate, which means the corresponding bit is not set in the
xfeatures bitmap of the init_fpstate header.
But __copy_xstate_to_uabi_buf() retrieves addresses for both the tasks
xstate and init_fpstate unconditionally via __raw_xsave_addr().
So if the tasks XSAVE buffer has a dynamic feature set, then the
address retrieval for init_fpstate triggers the warning in
__raw_xsave_addr() which checks the feature bit in the init_fpstate
header.
Remove the address retrieval from init_fpstate for extended features.
They have an all zeroes init state so init_fpstate has zeros for them.
Then zeroing the user buffer for the init state is the same as copying
them from init_fpstate.
Fixes: 2308ee57d9 ("x86/fpu/amx: Enable the AMX feature in 64-bit mode")
Reported-by: Mingwei Zhang <mizhang@google.com>
Link: https://lore.kernel.org/kvm/20230221163655.920289-2-mizhang@google.com/
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Mingwei Zhang <mizhang@google.com>
Link: https://lore.kernel.org/all/20230227210504.18520-2-chang.seok.bae%40intel.com
Cc: stable@vger.kernel.org
The hardware XRSTOR instruction resets the PKRU register to its hardware
init value (namely 0) if the PKRU bit is not set in the xfeatures mask.
Emulating that here restores the pre-5.14 behavior for PTRACE_SET_REGSET
with NT_X86_XSTATE, and makes sigreturn (which still uses XRSTOR) and
ptrace behave identically. KVM has never used XRSTOR and never had this
behavior, so KVM opts-out of this emulation by passing a NULL pkru pointer
to copy_uabi_to_xstate().
Fixes: e84ba47e31 ("x86/fpu: Hook up PKRU into ptrace()")
Signed-off-by: Kyle Huey <me@kylehuey.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20221115230932.7126-6-khuey%40kylehuey.com
Move KVM's PKRU handling code in fpu_copy_uabi_to_guest_fpstate() to
copy_uabi_to_xstate() so that it is shared with other APIs that write the
XSTATE such as PTRACE_SETREGSET with NT_X86_XSTATE.
This restores the pre-5.14 behavior of ptrace. The regression can be seen
by running gdb and executing `p $pkru`, `set $pkru = 42`, and `p $pkru`.
On affected kernels (5.14+) the write to the PKRU register (which gdb
performs through ptrace) is ignored.
[ dhansen: removed stable@ tag for now. The ABI was broken for long
enough that this is not urgent material. Let's let it stew
in tip for a few weeks before it's submitted to stable
because there are so many ABIs potentially affected. ]
Fixes: e84ba47e31 ("x86/fpu: Hook up PKRU into ptrace()")
Signed-off-by: Kyle Huey <me@kylehuey.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20221115230932.7126-5-khuey%40kylehuey.com
In preparation for moving PKRU handling code out of
fpu_copy_uabi_to_guest_fpstate() and into copy_uabi_to_xstate(), add an
argument that copy_uabi_from_kernel_to_xstate() can use to pass the
canonical location of the PKRU value. For
copy_sigframe_from_user_to_xstate() the kernel will actually restore the
PKRU value from the fpstate, but pass in the thread_struct's pkru location
anyways for consistency.
Signed-off-by: Kyle Huey <me@kylehuey.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20221115230932.7126-4-khuey%40kylehuey.com
Both KVM (through KVM_SET_XSTATE) and ptrace (through PTRACE_SETREGSET
with NT_X86_XSTATE) ultimately call copy_uabi_from_kernel_to_xstate(),
but the canonical locations for the current PKRU value for KVM guests
and processes in a ptrace stop are different (in the kvm_vcpu_arch and
the thread_state structs respectively).
In preparation for eventually handling PKRU in
copy_uabi_to_xstate, pass in a pointer to the PKRU location.
Signed-off-by: Kyle Huey <me@kylehuey.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20221115230932.7126-3-khuey%40kylehuey.com
This will allow copy_sigframe_from_user_to_xstate() to grab the address of
thread_struct's pkru value in a later patch.
Signed-off-by: Kyle Huey <me@kylehuey.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20221115230932.7126-2-khuey%40kylehuey.com
"XSAVE consistency problem" has been reported under Xen, but that's the extent
of my divination skills.
Modify XSTATE_WARN_ON() to force the caller to provide relevant diagnostic
information, and modify each caller suitably.
For check_xstate_against_struct(), this removes a double WARN() where one will
do perfectly fine.
CC stable as this has been wonky debugging for 7 years and it is good to
have there too.
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220810221909.12768-1-andrew.cooper3@citrix.com
When an extended state component is not present in fpstate, but in init
state, the function copies from init_fpstate via copy_feature().
But, dynamic states are not present in init_fpstate because of all-zeros
init states. Then retrieving them from init_fpstate will explode like this:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:memcpy_erms+0x6/0x10
? __copy_xstate_to_uabi_buf+0x381/0x870
fpu_copy_guest_fpstate_to_uabi+0x28/0x80
kvm_arch_vcpu_ioctl+0x14c/0x1460 [kvm]
? __this_cpu_preempt_check+0x13/0x20
? vmx_vcpu_put+0x2e/0x260 [kvm_intel]
kvm_vcpu_ioctl+0xea/0x6b0 [kvm]
? kvm_vcpu_ioctl+0xea/0x6b0 [kvm]
? __fget_light+0xd4/0x130
__x64_sys_ioctl+0xe3/0x910
? debug_smp_processor_id+0x17/0x20
? fpregs_assert_state_consistent+0x27/0x50
do_syscall_64+0x3f/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Adjust the 'mask' to zero out the userspace buffer for the features that
are not available both from fpstate and from init_fpstate.
The dynamic features depend on the compacted XSAVE format. Ensure it is
enabled before reading XCOMP_BV in init_fpstate.
Fixes: 2308ee57d9 ("x86/fpu/amx: Enable the AMX feature in 64-bit mode")
Reported-by: Yuan Yao <yuan.yao@intel.com>
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Yuan Yao <yuan.yao@intel.com>
Link: https://lore.kernel.org/lkml/BYAPR11MB3717EDEF2351C958F2C86EED95259@BYAPR11MB3717.namprd11.prod.outlook.com/
Link: https://lkml.kernel.org/r/20221021185844.13472-1-chang.seok.bae@intel.com
== Background ==
The XSTATE init code initializes all enabled and supported components.
Then, the init states are saved in the init_fpstate buffer that is
statically allocated in about one page.
The AMX TILE_DATA state is large (8KB) but its init state is zero. And the
feature comes only with the compacted format with these established
dependencies: AMX->XFD->XSAVES. So this state is excludable from
init_fpstate.
== Problem ==
But the buffer is formatted to include that large state. Then, this can be
the cause of a noisy splat like the below.
This came from XRSTORS for the task with init_fpstate in its XSAVE buffer.
It is reproducible on AMX systems when the running kernel is built with
CONFIG_DEBUG_PAGEALLOC=y and CONFIG_DEBUG_PAGEALLOC_ENABLE_DEFAULT=y:
Bad FPU state detected at restore_fpregs_from_fpstate+0x57/0xd0, reinitializing FPU registers.
...
RIP: 0010:restore_fpregs_from_fpstate+0x57/0xd0
? restore_fpregs_from_fpstate+0x45/0xd0
switch_fpu_return+0x4e/0xe0
exit_to_user_mode_prepare+0x17b/0x1b0
syscall_exit_to_user_mode+0x29/0x40
do_syscall_64+0x67/0x80
? do_syscall_64+0x67/0x80
? exc_page_fault+0x86/0x180
entry_SYSCALL_64_after_hwframe+0x63/0xcd
== Solution ==
Adjust init_fpstate to exclude dynamic states. XRSTORS from init_fpstate
still initializes those states when their bits are set in the
requested-feature bitmap.
Fixes: 2308ee57d9 ("x86/fpu/amx: Enable the AMX feature in 64-bit mode")
Reported-by: Lin X Wang <lin.x.wang@intel.com>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Lin X Wang <lin.x.wang@intel.com>
Link: https://lore.kernel.org/r/20220824191223.1248-4-chang.seok.bae@intel.com
The init_fpstate buffer is statically allocated. Thus, the sanity test was
established to check whether the pre-allocated buffer is enough for the
calculated size or not.
The currently measured size is not strictly relevant. Fix to validate the
calculated init_fpstate size with the pre-allocated area.
Also, replace the sanity check function with open code for clarity. The
abstraction itself and the function naming do not tend to represent simply
what it does.
Fixes: 2ae996e0c1 ("x86/fpu: Calculate the default sizes independently")
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20220824191223.1248-3-chang.seok.bae@intel.com
The init_fpstate setup code is spread out and out of order. The init image
is recorded before its scoped features and the buffer size are determined.
Determine the scope of init_fpstate components and its size before
recording the init state. Also move the relevant code together.
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: neelnatu@google.com
Link: https://lore.kernel.org/r/20220824191223.1248-2-chang.seok.bae@intel.com
thus allow for guests to use this compacted XSTATE variant when the
hypervisor exports that support
- A variable shadowing cleanup
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEzv7L6UO9uDPlPSfHEsHwGGHeVUoFAmKLsPQACgkQEsHwGGHe
VUoA7hAAoAP6qWntADHcDcA8QMjX9fvOi3uFjiJyGeiYCRH2rmwAAg8Y0DdI/1UE
Wq+7tzTPdyDPulqaEe9PV7f3HRY72cGA/2jdkMxkGG5mGZfVganb0OWgFXecdo6r
CIWf9vMOPwULIT4XvcnaWF6fv+1ZbFZOks9NpxZQZTYA3WQhozgfQOWlkoFFSdC/
pIwWFCUOv/pBPWVSeizE/Y6Yfuaix3KiElwk9NMDTPCRhyBd6VmpkpcBer+n3JUA
HoppbGLYonZEw1PkMmTlQJuFHKJzqwThGGoVY3FDtlAMD4+vmGt1vXNbLlfvtqup
zYHAIG/hqql7Ai9bgXSC2ccYG9v1op+gIFzKTBhI7FkVwEc6R6JtV7uGF7GAr6SL
KPnweo9GCoRmnc6Ju0+IuT0JIMXjO3iQIC0J3uLX8gCbsXVM29qdqhkYcLC75vOc
sXjAUrdolkDIRXzwkJURTxWT/yeKaN9n8r1s7BCmZ7Pg6zZS3/K1nHQkFTWCjSfA
oEy7GmEeI2uFgQX9qpF7NRlNj+D3AxV6W5IURCTI7GsP32e20jhOdU4AyrqsTy2N
8PgUVP9baioUpjY6BKsMc3JiR0ihb0OM3wX9fThu8lu5uHE9Oar+S4OOlFtxPXth
kG7pIS0MqB4N6aKWDFxvLvlUVgAxSqSmnWL4rQSP+Ralu9CY4k0=
=eDaz
-----END PGP SIGNATURE-----
Merge tag 'x86_fpu_for_v5.19_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fpu updates from Borislav Petkov:
- Add support for XSAVEC - the Compacted XSTATE saving variant - and
thus allow for guests to use this compacted XSTATE variant when the
hypervisor exports that support
- A variable shadowing cleanup
* tag 'x86_fpu_for_v5.19_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Cleanup variable shadowing
x86/fpu/xsave: Support XSAVEC in the kernel
The functions invoked via do_arch_prctl_common() can only operate on
the current task and none of these function uses the task argument.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/87lev7vtxj.ffs@tglx
Addresses: warning: Local variable 'mask' shadows outer variable
Remove extra variable declaration and switch the bit mask assignment to use
BIT_ULL() while at it.
Fixes: 522e92743b ("x86/fpu: Deduplicate copy_uabi_from_user/kernel_to_xstate()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/lkml/202204262032.jFYKit5j-lkp@intel.com
XSAVEC is the user space counterpart of XSAVES which cannot save supervisor
state. In virtualization scenarios the hypervisor does not expose XSAVES
but XSAVEC to the guest, though the kernel does not make use of it.
That's unfortunate because XSAVEC uses the compacted format of saving the
XSTATE. This is more efficient in terms of storage space vs. XSAVE[OPT] as
it does not create holes for XSTATE components which are not supported or
enabled by the kernel but are available in hardware. There is room for
further optimizations when XSAVEC/S and XGETBV1 are supported.
In order to support XSAVEC:
- Define the XSAVEC ASM macro as it's not yet supported by the required
minimal toolchain.
- Create a software defined X86_FEATURE_XCOMPACTED to select the compacted
XSTATE buffer format for both XSAVEC and XSAVES.
- Make XSAVEC an option in the 'XSAVE' ASM alternatives
Requested-by: Andrew Cooper <Andrew.Cooper3@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20220404104820.598704095@linutronix.de
Use the offset calculation to do the size calculation which avoids yet
another series of CPUID instructions for each invocation.
[ Fix the FP/SSE only case which missed to take the xstate
header into account, as
Reported-by: kernel test robot <oliver.sang@intel.com> ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/87o81pgbp2.ffs@tglx
The size calculation in __xstate_request_perm() fails to take supervisor
states into account because the permission bitmap is only relevant for user
states.
Up to 5.17 this does not matter because there are no supervisor states
supported, but the (re-)enabling of ENQCMD makes them available.
Fixes: 7c1ef59145 ("x86/cpufeatures: Re-enable ENQCMD")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220324134623.681768598@linutronix.de
So far the cached fixed compacted offsets worked, but with (re-)enabling
of ENQCMD this does no longer work with KVM fpstate.
KVM does not have supervisor features enabled for the guest FPU, which
means that KVM has then a different XSAVE area layout than the host FPU
state. This in turn breaks the copy from/to UABI functions when invoked for
a guest state.
Remove the pre-calculated compacted offsets and calculate the offset
of each component at runtime based on the XCOMP_BV field in the XSAVE
header.
The runtime overhead is not interesting because these copy from/to UABI
functions are not used in critical fast paths. KVM uses them to save and
restore FPU state during migration. The host uses them for ptrace and for
the slow path of 32bit signal handling.
Fixes: 7c1ef59145 ("x86/cpufeatures: Re-enable ENQCMD")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220324134623.627636809@linutronix.de
In preparation for runtime calculation of XSAVE offsets cache the feature
flags for each XSTATE component during feature enumeration via CPUID(0xD).
EDX has two relevant bits:
0 Supervisor component
1 Feature storage must be 64 byte aligned
These bits are currently only evaluated during init, but the alignment bit
must be cached to make runtime calculation of XSAVE offsets efficient.
Cache the full EDX content and use it for the existing alignment and
supervisor checks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220324134623.573656209@linutronix.de
Reading XSTATE feature information from CPUID over and over does not make
sense. The information has to be cached anyway, so it can be done early.
Prepare for runtime calculation of XSTATE offsets and allow
consolidation of the size calculation functions in a later step.
Rename the function while at it as it does not setup any features.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220324134623.519411939@linutronix.de
ARCH_REQ_XCOMP_PERM is supposed to add the requested feature to the
permission bitmap of thread_group_leader()->fpu. But the code overwrites
the bitmap with the requested feature bit only rather than adding it.
Fix the code to add the requested feature bit to the master bitmask.
Fixes: db8268df09 ("x86/arch_prctl: Add controls for dynamic XSTATE components")
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Paolo Bonzini <bonzini@gnu.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220129173647.27981-2-chang.seok.bae@intel.com
During host/guest switch (like in kvm_arch_vcpu_ioctl_run()), the kernel
swaps the fpu between host/guest contexts, by using fpu_swap_kvm_fpstate().
When xsave feature is available, the fpu swap is done by:
- xsave(s) instruction, with guest's fpstate->xfeatures as mask, is used
to store the current state of the fpu registers to a buffer.
- xrstor(s) instruction, with (fpu_kernel_cfg.max_features &
XFEATURE_MASK_FPSTATE) as mask, is used to put the buffer into fpu regs.
For xsave(s) the mask is used to limit what parts of the fpu regs will
be copied to the buffer. Likewise on xrstor(s), the mask is used to
limit what parts of the fpu regs will be changed.
The mask for xsave(s), the guest's fpstate->xfeatures, is defined on
kvm_arch_vcpu_create(), which (in summary) sets it to all features
supported by the cpu which are enabled on kernel config.
This means that xsave(s) will save to guest buffer all the fpu regs
contents the cpu has enabled when the guest is paused, even if they
are not used.
This would not be an issue, if xrstor(s) would also do that.
xrstor(s)'s mask for host/guest swap is basically every valid feature
contained in kernel config, except XFEATURE_MASK_PKRU.
Accordingto kernel src, it is instead switched in switch_to() and
flush_thread().
Then, the following happens with a host supporting PKRU starts a
guest that does not support it:
1 - Host has XFEATURE_MASK_PKRU set. 1st switch to guest,
2 - xsave(s) fpu regs to host fpustate (buffer has XFEATURE_MASK_PKRU)
3 - xrstor(s) guest fpustate to fpu regs (fpu regs have XFEATURE_MASK_PKRU)
4 - guest runs, then switch back to host,
5 - xsave(s) fpu regs to guest fpstate (buffer now have XFEATURE_MASK_PKRU)
6 - xrstor(s) host fpstate to fpu regs.
7 - kvm_vcpu_ioctl_x86_get_xsave() copy guest fpstate to userspace (with
XFEATURE_MASK_PKRU, which should not be supported by guest vcpu)
On 5, even though the guest does not support PKRU, it does have the flag
set on guest fpstate, which is transferred to userspace via vcpu ioctl
KVM_GET_XSAVE.
This becomes a problem when the user decides on migrating the above guest
to another machine that does not support PKRU: the new host restores
guest's fpu regs to as they were before (xrstor(s)), but since the new
host don't support PKRU, a general-protection exception ocurs in xrstor(s)
and that crashes the guest.
This can be solved by making the guest's fpstate->user_xfeatures hold
a copy of guest_supported_xcr0. This way, on 7 the only flags copied to
userspace will be the ones compatible to guest requirements, and thus
there will be no issue during migration.
As a bonus, it will also fail if userspace tries to set fpu features
(with the KVM_SET_XSAVE ioctl) that are not compatible to the guest
configuration. Such features will never be returned by KVM_GET_XSAVE
or KVM_GET_XSAVE2.
Also, since kvm_vcpu_after_set_cpuid() now sets fpstate->user_xfeatures,
there is not need to set it in kvm_check_cpuid(). So, change
fpstate_realloc() so it does not touch fpstate->user_xfeatures if a
non-NULL guest_fpu is passed, which is the case when kvm_check_cpuid()
calls it.
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Message-Id: <20220217053028.96432-2-leobras@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Userspace needs to inquire KVM about the buffer size to work
with the new KVM_SET_XSAVE and KVM_GET_XSAVE2. Add the size info
to guest_fpu for KVM to access.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Jing Liu <jing2.liu@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20220105123532.12586-18-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Guest support for dynamically enabled FPU features requires a few
modifications to the enablement function which is currently invoked from
the #NM handler:
1) Use guest permissions and sizes for the update
2) Update fpu_guest state accordingly
3) Take into account that the enabling can be triggered either from a
running guest via XSETBV and MSR_IA32_XFD write emulation or from
a guest restore. In the latter case the guests fpstate is not the
current tasks active fpstate.
Split the function and implement the guest mechanics throughout the
callchain.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jing Liu <jing2.liu@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20220105123532.12586-7-yang.zhong@intel.com>
[Add 32-bit stub for __xfd_enable_feature. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM requires a clear separation of host user space and guest permissions
for dynamic XSTATE components.
Add a guest permissions member to struct fpu and a separate set of prctl()
arguments: ARCH_GET_XCOMP_GUEST_PERM and ARCH_REQ_XCOMP_GUEST_PERM.
The semantics are equivalent to the host user space permission control
except for the following constraints:
1) Permissions have to be requested before the first vCPU is created
2) Permissions are frozen when the first vCPU is created to ensure
consistency. Any attempt to expand permissions via the prctl() after
that point is rejected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jing Liu <jing2.liu@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20220105123532.12586-2-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the AMX state components in XFEATURE_MASK_USER_SUPPORTED and the
TILE_DATA component to the dynamic states and update the permission check
table accordingly.
This is only effective on 64 bit kernels as for 32bit kernels
XFEATURE_MASK_TILE is defined as 0.
TILE_DATA is caller-saved state and the only dynamic state. Add build time
sanity check to ensure the assumption that every dynamic feature is caller-
saved.
Make AMX state depend on XFD as it is dynamic feature.
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211021225527.10184-24-chang.seok.bae@intel.com
To handle the dynamic sizing of buffers on first use the XFD MSR has to be
armed. Store the delta between the maximum available and the default
feature bits in init_fpstate where it can be retrieved for task creation.
If the delta is non zero then dynamic features are enabled. This needs also
to enable the static key which guards the XFD updates. This is delayed to
an initcall because the FPU setup runs before jump labels are initialized.
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211021225527.10184-23-chang.seok.bae@intel.com
When dynamically enabled states are supported the maximum and default sizes
for the kernel buffers and user space interfaces are not longer identical.
Put the necessary calculations in place which only take the default enabled
features into account.
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211021225527.10184-22-chang.seok.bae@intel.com
The XSTATE initialization uses check_xstate_against_struct() to sanity
check the size of XSTATE-enabled features. AMX is a XSAVE-enabled feature,
and its size is not hard-coded but discoverable at run-time via CPUID.
The AMX state is composed of state components 17 and 18, which are all user
state components. The first component is the XTILECFG state of a 64-byte
tile-related control register. The state component 18, called XTILEDATA,
contains the actual tile data, and the state size varies on
implementations. The architectural maximum, as defined in the CPUID(0x1d,
1): EAX[15:0], is a byte less than 64KB. The first implementation supports
8KB.
Check the XTILEDATA state size dynamically. The feature introduces the new
tile register, TMM. Define one register struct only and read the number of
registers from CPUID. Cross-check the overall size with CPUID again.
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211021225527.10184-21-chang.seok.bae@intel.com
The kernel checks at boot time which features are available by walking a
XSAVE feature table which contains the CPUID feature bit numbers which need
to be checked whether a feature is available on a CPU or not. So far the
feature numbers have been linear, but AMX will create a gap which the
current code cannot handle.
Make the table entries explicitly indexed and adjust the loop code
accordingly to prepare for that.
No functional change.
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211021225527.10184-20-chang.seok.bae@intel.com
The fpstate embedded in struct fpu is the default state for storing the FPU
registers. It's sized so that the default supported features can be stored.
For dynamically enabled features the register buffer is too small.
The #NM handler detects first use of a feature which is disabled in the
XFD MSR. After handling permission checks it recalculates the size for
kernel space and user space state and invokes fpstate_realloc() which
tries to reallocate fpstate and install it.
Provide the allocator function which checks whether the current buffer size
is sufficient and if not allocates one. If allocation is successful the new
fpstate is initialized with the new features and sizes and the now enabled
features is removed from the task's XFD mask.
realloc_fpstate() uses vzalloc(). If use of this mechanism grows to
re-allocate buffers larger than 64KB, a more sophisticated allocation
scheme that includes purpose-built reclaim capability might be justified.
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211021225527.10184-19-chang.seok.bae@intel.com
If the XFD MSR has feature bits set then #NM will be raised when user space
attempts to use an instruction related to one of these features.
When the task has no permissions to use that feature, raise SIGILL, which
is the same behavior as #UD.
If the task has permissions, calculate the new buffer size for the extended
feature set and allocate a larger fpstate. In the unlikely case that
vzalloc() fails, SIGSEGV is raised.
The allocation function will be added in the next step. Provide a stub
which fails for now.
[ tglx: Updated serialization ]
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211021225527.10184-18-chang.seok.bae@intel.com
The IA32_XFD_MSR allows to arm #NM traps for XSTATE components which are
enabled in XCR0. The register has to be restored before the tasks XSTATE is
restored. The life time rules are the same as for FPU state.
XFD is updated on return to userspace only when the FPU state of the task
is not up to date in the registers. It's updated before the XRSTORS so
that eventually enabled dynamic features are restored as well and not
brought into init state.
Also in signal handling for restoring FPU state from user space the
correctness of the XFD state has to be ensured.
Add it to CPU initialization and resume as well.
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211021225527.10184-17-chang.seok.bae@intel.com
