[Why]
A race condition occurs between cursor movement and vertical interrupt control
thread from OS, with both threads trying to exit IPS2.
Vertical interrupt control thread clears the prev driver allow signal while not fully
finishing the IPS2 exit process.
[How]
We want to detect all the allow signals have been cleared before we perform the full exit.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This enables starting and stopping IPS residency measurements
and querying the IPS residency information consisting of residency
percent, entry counter, total time active & inactive, and histograms
for the specified IPS mode.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We intend to consolidate dp tunneling and conventional dp link training.
[HOW]
1. Use the same link training entry for both dp and dpia
2. Move SET_CONFIG of non-transparent mode to dmub side
3. Add set_tps_notification dmub_cmd to notify tps request for
non-transparent dpia link training
4. Check dpcd request result and abort link training early if dpia
aux tunneling fails
5. Add option to avoid affect old product
6. Separately handle wait_time_microsec for dpia
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to avoid arming the HPD timer in firmware when preparing for
S0i3 entry when DC is considered in D3.
[How]
Notify DMCUB of the power state transitions so it can decide to arm
the HPD timer for idle in DCN35 only in D0.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drop coasting_vtotal_high and pad from dmub_cmd_update_dirty_rect_data,
since it is not used.
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The DP tunnel AUX reply is received through Outbox1. Print the Outbox1
status if an issue occurs.
Signed-off-by: Cruise <Cruise.Hung@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Visual Confirm would tell us if it ever
entered idle state.
[How]
Add debug option for IPS visual confirm
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM can hook this up to disable SLDO optimizations in firmware during
DMCUB initialization for debug purposes.
[How]
Add the option and pass it through dmub_srv.
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add new Replay states 2A (initial Replay entry) and 4E (frame update)
to check is there is new frame update before sending
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add new condition for PSR exit due to ESD recovery
- Add new VB scaling feature for ABM by interpolating between
existing VB parameters, allowing driver to have fine grain
scaled VB levels between 0 - 250
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Create a general command and fix Replay desync error with general cmd
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
Add additional delay factor when considering a safe time to flip for HWFQ
to be passed in by the driver.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These registers should not be read from driver and triggering the
security violation when DMCUB work times out and diagnostics are
collected blocks Z8 entry.
[How]
Remove the register read from DCN35.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Define debug interface to dmub for reading back abm data.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Josip Pavic <josip.pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Change ordering of structs to put enums together
- Add new define DMUB_TRACE_ENTRY_DEFINED to guard
the trace code enum
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The original coasting vtotal is 2 bytes, and it need to be amended to 4
bytes because low hz case.
[How]
Amend coasting vtotal from 2 bytes to 4 bytes.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: ChunTao Tso <ChunTao.Tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some panel, it cannot handle pseudo vblank set by otg resync
when leave psr
[How]
The monitor patch will keep otg_on during enter IPS1.
And then we don't need to do otg resync when wake up.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
Add 5ms timeout to trigger recovery and force allow P-State in DMUB.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. To support multiple PSRSU residency measurement mode
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Jack Chang <jack.chang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD sense changes can occur during low power states and need to be
notified from firmware to driver. Upon notification the hotplug
redetection routines should execute.
[How]
Add Support in DMUB srv and DMUB srv stat for receiving these
notifications. DM can hook them up and process the HPD redetection
once received.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Add parameters for set_abm_event to enable varibright scaling.
VariBright Scaling is a feature to refer to system states like
1. Power mode
2. Battery Life percent
3. FullScreen video
4. Backlight slider
to adjust variBright strength to get low power or user experience.
[How]
Add parameters of set_abm_event for VB Scaling
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Chun-LiangChang <chuchang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New commands for enabling copy of DC bounding box values from VBIOS DMUB
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DPIA boot option is set by VBIOS. It gets
overwritten when driver loads DMU.
[HOW]
Read PreOS boot options and determine if
dpia is enabled.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Implement command interface to query ABM SW algorithm and
HW caps. This is primarily intended as a debugging interface
- Add new definitions for max number of histogram bins and ABM
curve segments available in hardware
- Add structures to retrieve caps to describe ABM HW caps
since not all ASICs have the same number of cure segments and
bins
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can hang in IPS2 checking DMCUB_SCRATCH0 for link detection state.
[How]
Replace the HW access with a check on the shared state bit. This will
work the same way as the SCRATCH0 but won't require a wake in the case
where link detection isn't required.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Adjust the dmub_fw_boot_options reserved bits to be correct
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dmub_cmd to manipulate SDP control in replay FSM, add command
for panel_cntl, expand link rate enum, and increase the reserve byte.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
IPS ono sequence ordering differs based on the ASIC.
[How]
Detect the ASIC ID revision and set the boot option accordingly. Feed
it through the DCN35 DMUB functions.
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add boot option to change the ONO powerup flow, impacting
the order of power domains to power up or down first
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Add logging for first DMUB inbox message that timed out to diagnostic
data
- It is useful to track the first failed message for debug purposes
because once DMUB becomes hung (typically on a message), it will
remain hung and all subsequent messages. In these cases we're
interested in knowing which is the first message that failed.
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
Update dmub and driver interface for future FAMS revisions.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We don't have a way to specify IPS2 for display off but RCG only for
static screen and local video playback.
[How]
Add a new setting that allows RCG only when displays are active but
IPS2 when all displays are off.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
To enable a new interface so alternate scrambling can be done via
security module.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Sung Joon Kim <sungjoon.kim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's possible to skip parts of the eval and exit sequencing if we know
whether DCN is in IPS2 already or if it's committed to going to idle
and not in IPS2.
[How]
Skip IPS2 entry/exit if DMCUB is idle but the IPS2 commit is not set.
Skip the eval delay if DMCUB is already in IPS2 since we know we need
to exit.
These are turned off by default.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add a Replay residency mode which only calcuates the
entry time based on replay state 0/1 switch.
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
- Update replay residency tracing design to support more types
including tracking PHY and ALPM residency types
- Add commands for Replay frame update count profiling
- Enhance HWFQ with additional flags to allow for more
optimized IPS low power state residencies
- Add new flag to indicate if a new frame update needed for
ABM to ramp up into steady state
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Add new counters in the shared IPS firmware state.
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The original coasting vtotal is 2 bytes, and it need to
be amended to 4 bytes because low hz case.
[HOW]
Amend coasting vtotal from 2 bytes to 4 bytes.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DMUB support is required to light-up displays.
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VBIOS DMCUB firmware doesn't set the dal_fw bit and we end up hanging
waiting for HW power up done because of it.
[How]
Simplify the path and allow mailbox_rdy to be a functional check when
we detect VBIOS firmware.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Read modify write hazards can occur when using a single shared scratch
register between driver and firmware leading to driver accessing DCN
in IPS2 and a system hang.
[How]
Add infrastructure for using REGION6 as a shared firmware state between
driver and firmware. This region is uncachable.
Replace the existing get/set idle calls with reads/writes to the
(volatile) shared firmware state blocks that a separated by at least
a cache line between firmware and driver.
Remove the workarounds that required rewriting/checking read modify
write hazards.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Display code keeps getting improvements, and because of that, some
legacy code is left behind. This commit drops some of those unused
codes.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add control flag for IPS residency profiling
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
