With WBRF feature supported, as a driver responding to the frequencies,
amdgpu driver is able to do shadow pstate switching to mitigate possible
interference(between its (G-)DDR memory clocks and local radio module
frequency bands used by Wifi 6/6e/7).
--
v1->v2:
- update the prompt for feature support(Lijo)
v8->v9:
- update parameter document for smu_wbrf_event_handler(Simon)
v9->v10:
v10->v11:
- correct the logics for wbrf range sorting(Lijo)
v13:
- Fix the format issue (IIpo Jarvinen)
Signed-off-by: Evan Quan <quanliangl@hotmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The smu needs to get the rlc power down message to sync the rlc state
with smu, the rlc state updating message need to be sent at while smu
begin suspend sequence , otherwise SMU will crash while RLC state is not
notified by driver, and rlc state probally changed after that
notification, so it needs to notify rlc state to smu at the end of the
suspend sequence in amdgpu_device_suspend() that can make sure the rlc
state is correctly set to SMU.
[ 101.000590] amdgpu 0000:03:00.0: amdgpu: SMU: I'm not done with your previous command: SMN_C2PMSG_66:0x0000001E SMN_C2PMSG_82:0x00000000
[ 101.000598] amdgpu 0000:03:00.0: amdgpu: Failed to disable gfxoff!
[ 110.838026] amdgpu 0000:03:00.0: amdgpu: SMU: I'm not done with your previous command: SMN_C2PMSG_66:0x0000001E SMN_C2PMSG_82:0x00000000
[ 110.838035] amdgpu 0000:03:00.0: amdgpu: Failed to disable smu features.
[ 110.838039] amdgpu 0000:03:00.0: amdgpu: Fail to disable dpm features!
[ 110.838040] [drm:amdgpu_device_ip_suspend_phase2 [amdgpu]] *ERROR* suspend of IP block <smu> failed -62
[ 110.884394] PM: suspend of devices aborted after 21213.620 msecs
[ 110.884402] PM: start suspend of devices aborted after 21213.882 msecs
[ 110.884405] PM: Some devices failed to suspend, or early wake event detected
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support for getting power1_cap_min value on smu13 and smu11.
For other Asics, we still use 0 as the default value.
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following errors reported by checkpatch:
ERROR: space prohibited before that ',' (ctx:WxW)
Signed-off-by: Ran Sun <sunran001@208suo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add debugfs interface to log GFXOFF statistics:
- Read amdgpu_gfxoff_count to get the total GFXOFF entry count at the
time of query since system power-up
- Write 1 to amdgpu_gfxoff_residency to start logging, and 0 to stop.
Read it to get average GFXOFF residency % multiplied by 100
during the last logging interval.
Both features are designed to be keep the values persistent between
suspends.
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With SCPM enabled, pptable cannot be uploaded to SMU directly.
The transferring has to be via PSP.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For Some ASICs, with the PMFW default settings, we may see the
power consumption reported via metrics table is "Very Erratic".
With the socket power alpha filter set as 10/100ms, we can correct
that issue.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For Cyan Skillfish and Renoir, there is no interface provided by PMFW
to retrieve the enabled features. So, we assume all features are enabled.
Fixes: 7ade3ca9cd ("drm/amd/pm: correct the usage for 'supported' member of smu_feature structure")
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As there is no internal cache for enabled ppfeatures now. Thus the 2nd
parameter will be not needed any more.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use uint64_t instead of an array of uint32_t. This can avoid
some non-necessary intermediate uint32_t -> uint64_t conversions.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Expose both SMU I2C buses. Some boards use the same bus for both the RAS
and FRU EEPROMs and others use different buses. This enables the
additional I2C bus and sets the right buses to use for RAS and FRU EEPROM
access.
Cc: Roy Sun <Roy.Sun@amd.com>
Co-developed-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As OOB(out-of-band) interface may be used to update the power limits.
Thus to make sure the power limits reporting of our driver always
reflects the correct values, the internal cache must be aligned
carefully.
V2: add support for out-of-band of other ASICs
align cached current power limit with OOB imposed
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-By: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For some ASICs, the real dpm feature disablement job is handled by
PMFW during baco reset and custom pptable loading. Cached dpm feature
status need to be updated to pair that.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to add the fine grain tuning function for vangogh.
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency or restore the default value.
Command guide:
echo "s level value" > pp_od_clk_voltage
"s" - set the sclk frequency
"level" - 0 or 1, "0" represents the min value, "1" represents
the max value
"value" - the target value of sclk frequency, it should be
limited in the safe range
echo "r" > pp_od_clk_voltage
"r" - reset the sclk frequency, restore the default value
instantly
echo "c" > pp_od_clk_voltage
"c" - commit the min and max value of sclk frequency to the system
only after the commit command, the setting target values by "s" command
will take effect.
Example:
1)check the default sclk frequency
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
2)use "s" -- set command to configure the min or max sclk frequency
$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ echo "c" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 600Mhz
1: 1000Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
3)use "r" -- reset command to restore the min and max sclk frequency
$ echo "r" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable/enable the GPO feature on UMD pstate entering/exiting.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These were leftover from the initial implementation, but
never used. Drop them.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Noticed-by: Ryan Taylor <ryan.taylor@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Either this was already performed in parent API. Or the table is
confirmed to exist.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
That's where the uclk dpm get enabled and then the
uclk cdr workaround can be applied.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that ASIC specific actions can be added.
V2: better namings
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add deep sleep disablement/enablement on UMD pstate entering/exiting.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add gfx ulv disablement/enablement on UMD pstate entering/exiting.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The target is to provide a clear entry point(for power routines).
Also this can help to maintain a clear view about the frameworks
used on different ASICs. Hopefully all these can make power part
more friendly to play with.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-14 16:22:41 -04:00
Renamed from drivers/gpu/drm/amd/powerplay/smu_internal.h (Browse further)
