Permanently set the connector status to 'connected'. Return BMC modes
for connector if no display is attached to the physical DP connector.
Otherwise use EDID modes as before.
If the status of the physical connector changes, the driver still
generates a hotplug event. DRM clients will then reconfigure their
output to a mode appropriate for either physical display or BMC.
v3:
- use struct ast_connector.physical_status to handle BMC
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-7-tzimmermann@suse.de
Remove the CRTC handling in the ASTDP detect_ctx helper and enable
power while the detecting the display. Unconditionally wait a few
milliseconds after switching power. Simplifies the code and makes it
more robust.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-6-tzimmermann@suse.de
Convert ASTDP support to struct drm_edid and its helpers. Simplifies
and modernizes the EDID handling.
The driver reads 4 bytes at once, but the overall read length is now
variable. Therefore update the EDID read loop to never return more than
the requested bytes.
The device does not seem to support EDID extensions, as the driver
actively clears any such information from the main EDID header. As
the new interface allows for reading extension blocks for EDID, make
sure that the block is always 0 (i.e., the main header). A later
update might fix that.
v2:
- fix reading if len is not a multiple of 4
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-5-tzimmermann@suse.de
The modeset mutex protects EDID retrival from concurrent modeset
operations. Acquire the lock in ast_astdp_read_edid(). Prepares the
code for conversion to struct drm_edid.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-4-tzimmermann@suse.de
Add struct ast_connector to track a connector's physical status. With
the upcoming BMC support, the physical status can be different from the
reported status.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-3-tzimmermann@suse.de
This code has an issue because it loops until "i" is set to UINT_MAX but
the test for failure assumes that "i" is set to zero. The result is that
it will only print an error message if we succeed on the very last try.
Reformat the loop to count forwards instead of backwards.
Fixes: 2281475168 ("drm/ast: astdp: Perform link training during atomic_enable")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1ba8da25-2d09-4924-a4ff-c0714bfbb192@stanley.mountain
The place for link training is in the encoder's atomic_enable
helper. Remove all related tests from other helper ASTDP functions;
especially ast_astdp_is_connected(), which tests HPD status.
DP link training is controlled by the firmware. A status flag reports
success or failure. The process can be fragile on Aspeed hardware. Moving
the test from connector detection to the atomic_enable allows for several
retries and a longer timeout.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240717143319.104012-5-tzimmermann@suse.de
The overall control flow of the driver ensures that it never reads
EDID or sets display state on unconnected outputs. Therefore remove
all tests for Hot Plug Detection from these helpers. Also rename
the register constants.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240717143319.104012-4-tzimmermann@suse.de
Test for running ASTDP firmware during probe. Do not bother testing
this later. We cannot do much anyway if the firmware fails. Do not
initialize the ASTDP conenctor if the test fails during device probing.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reported-by: Shixiong Ou <oushixiong@kylinos.cn>
Tested-by: Shixiong Ou <oushixiong@kylinos.cn>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240717143319.104012-3-tzimmermann@suse.de
Power up the ASTDP connector for connection status detection if the
connector is not active. Keep it powered if a display is attached.
This fixes a bug where the connector does not come back after
disconnecting the display. The encoder's atomic_disable turns off
power on the physical connector. Further HPD reads will fail,
thus preventing the driver from detecting re-connected displays.
For connectors that are actively used, only test the HPD flag without
touching power.
Fixes: f81bb0ac78 ("drm/ast: report connection status on Display Port.")
Cc: Jocelyn Falempe <jfalempe@redhat.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.6+
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240717143319.104012-2-tzimmermann@suse.de
There is a while-loop in ast_dp_set_on_off() that could lead to
infinite-loop. This is because the register, VGACRI-Dx, checked in
this API is a scratch register actually controlled by a MCU, named
DPMCU, in BMC.
These scratch registers are protected by scu-lock. If suc-lock is not
off, DPMCU can not update these registers and then host will have soft
lockup due to never updated status.
DPMCU is used to control DP and relative registers to handshake with
host's VGA driver. Even the most time-consuming task, DP's link
training, is less than 100ms. 200ms should be enough.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Fixes: 594e9c04b5 ("drm/ast: Create the driver for ASPEED proprietory Display-Port")
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: KuoHsiang Chou <kuohsiang_chou@aspeedtech.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jocelyn Falempe <jfalempe@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.19+
Link: https://patchwork.freedesktop.org/patch/msgid/20240403090246.1495487-1-jammy_huang@aspeedtech.com
Aspeed always report the display port as "connected", because it
doesn't set a .detect_ctx callback.
Fix this by providing the proper detect callback for astdp and dp501.
This also fixes the following regression:
Since commit fae7d18640 ("drm/probe-helper: Default to 640x480 if no
EDID on DP") The default resolution is now 640x480 when no monitor is
connected. But Aspeed graphics is mostly used in servers, where no monitor
is attached. This also affects the remote BMC resolution to 640x480, which
is inconvenient, and breaks the anaconda installer.
v2: Add .detect callback to the dp/dp501 connector (Jani Nikula)
v3: Use .detect_ctx callback, and refactors (Thomas Zimmermann)
Add a BMC virtual connector
v4: Better indent detect_ctx() functions (Thomas Zimmermann)
v5: Enable polling of the dp and dp501 connector status
(Thomas Zimmermann)
v6: Change check order in ast_astdp_is_connected (Jammy Huang)
Fixes: fae7d18640 ("drm/probe-helper: Default to 640x480 if no EDID on DP")
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713134316.332502-2-jfalempe@redhat.com
In resume, DP's launch function, ast_dp_launch, could wait at most 30
seconds before timeout to check if DP is enabled. It could lead to 'DPM
device timeout' and trigger unrecoverable kernel panic.
To avoid this problem, we check if DP enable or not at driver probe only.
Reported-and-tested-by: Wendy Wang <wendy.wang@intel.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217278
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230530041240.13427-1-jammy_huang@aspeedtech.com
The data structure struct ast_private represents an AST device. Its
name comes from the time when it was allocated and stored separately
in struct drm_device.dev_private. The DRM device is now embedded, so
rename struct ast_private to struct ast_device.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230221155745.27484-4-tzimmermann@suse.de
Systems with AST graphics can have multiple output; typically VGA
plus some other port. Record detected output chips in a bitmask and
initialize each output on its own.
Assume a VGA output by default and use SIL164 and DP501 if available.
For ASTDP assume that it can run in parallel with VGA.
Tested on AST2100.
v3:
* define a macro for each BIT(ast_tx_chip) (Patrik)
v2:
* make VGA/SIL164/DP501 mutually exclusive
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Fixes: a59b026419 ("drm/ast: Initialize encoder and connector for VGA in helper function")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220607092008.22123-2-tzimmermann@suse.de
V1:
1. The MCU FW controling ASPEED DP is loaded by BMC boot loader.
2. Driver starts after CR[3:1] == 111b that indicates Tx is ASTDP,
and CRD1[5] has been asserted by BMVC boot loader.
3. EDID is prioritized by DP monitor.
4. DP's EDID has high priority to decide resolution supporting.
V2:
Modules description:
1. ASTDP (ASPEED DisplayPort) is controlled by dedicated
AST-MCU (ASPEED propriatary MCU).
2. MCU is looping in charged of HPD, Read EDID, Link Training with
DP sink.
3. ASTDP and AST-MUC reside in BMC (Baseboard Management controller)
addressing-space.
4. ASPEED DRM driver requests MCU to get HPD and EDID by CR-scratched
register.
Booting sequence:
1. Check if TX is ASTDP // ast_dp_launch()
2. Check if DP-MCU FW has loaded // ast_dp_launch()
3. Read EDID // ast_dp_read_edid()
4. Resolution switch // ast_dp_SetOutput()
V3:
1. Remove unneeded semicolon.
2. Apply to git://anongit.freedesktop.org/drm/drm, instead of
git://anongit.freedesktop.org/drm/drm-misc
3. Resolve auto build test WARNINGs on V1 patch.
V4:
1. Sync code-base with kernel 5.17_rc6
2. Remove the define of DPControlPower, because DP chips need to be
powered on to be used.
3. Remove the switches of PHY and Display from EDID procedure.
4. Revise increaing delay to fixed delay, because this version kernel
doesn't detect minitor consistenntly.
5. Create clean-up code used for reset of power state on errors with
-EIO manner.
6. Revise the DP detection by TX type and its DP-FW status during
booting and resume.
7. Correct the CamelCase Style.
8. Use register reading while needing, and remove to hold full
register.
9. Instead of 'u8', revise to 'bool' on swwitch of PHY and video.
10.Correct typo
11.Remove the duplicated copy of TX definition.
12.Use EDID_LENGTH as the constant of 128.
Signed-off-by: KuoHsiang Chou <kuohsiang_chou@aspeedtech.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428075603.20904-1-kuohsiang_chou@aspeedtech.com
