drm_bridge_connector is a "leaf" driver, belonging to the display
helper, rather than the "CRTC" drm_kms_helper module. Move the driver
to the drm/display and add necessary Kconfig selection clauses.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240903-drm-bridge-connector-fix-hdmi-reset-v5-2-daebde6d9857@linaro.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Using the correct bit helps. The documentation specifies bit 0 in both
registers to be controlling polarity of dpi_vsync_input and
dpi_hsync_input polarity. Bit 1 is reserved, and should therefore not be
set.
Tested with panel that requires active high vsync and hsync.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240814-nwl-dsi-sync-polarity-v1-1-ee198e369196@geanix.com
There's no need to get the length of an DT array property before
parsing the array. of_property_read_variable_u8_array() takes a minimum
and maximum length and returns the actual length (or error code).
This is part of a larger effort to remove callers of of_get_property()
and similar functions. of_get_property() leaks the DT property data
pointer which is a problem for dynamically allocated nodes which may
be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240731201407.1838385-4-robh@kernel.org
Make use of devm_clk_get_enabled() to replace devm_clk_get() and
clk_prepare_enable() for isfr and iahb clocks, and drop the now
unnecessary calls to clk_disable_unprepare().
Similarly, use devm_clk_get_optional_enabled() helper for cec clock,
which additionally allows to remove the -ENOENT test.
Moreover, the clock related members of struct dw_hdmi are not required
anymore, hence drop them.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240813-dw-hdmi-simple-clk-v1-1-78d45cef02a9@collabora.com
If the bridge is attached with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag set,
this driver won't initialize a connector and hence display mode won't be
validated in drm_connector_helper_funcs::mode_valid(). So, move the mode
validation from drm_connector_helper_funcs::mode_valid() to
drm_bridge_funcs::mode_valid(), because the mode validation is always done
for the bridge.
Fixes: 30e2ae943c ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240813091637.1054586-1-victor.liu@nxp.com
Having no in-kernel devices that use !DRM_BRIDGE_ATTACH_NO_CONNECTOR
mode for the Lontium LT9611UXC bridge, drop the in-bridge implementation
of the drm_connector.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240701-lt9611uxc-next-bridge-v1-2-665bce5fdaaa@linaro.org
Enable the transmission of an EoTp (end of transmission packet) by
default. EoTp should be enabled anyway because it is a Linux necessity
that can be disabled by a dsi mod_flag if needed.
EoTp signals the end of an HS transmission, this adds overall robustness
at protocol level at the expense of an increased overhead.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/6a7293bd06942131161c5a7b7878c51cfbbb807e.camel@googlemail.com
When the bridge is powered off, disable the IRQ until the next power on
to workaround an interrupt storm on some badly-designed hardware.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240719110623.1850021-1-treapking@chromium.org
Make the default DP port preemphasis configurable via new DT property
"toshiba,pre-emphasis". This is useful in case the DP link properties
are known and starting link training from preemphasis setting of 0 dB
is not useful. The preemphasis can be set separately for both DP lanes
in range 0=0dB, 1=3.5dB, 2=6dB .
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240708150130.54484-2-marex@denx.de
commit 6a1688ae87 ("drm/bridge: ptn3460: Convert to I2C driver model")
has dropped all the users of the struct bridge_init from the
exynos_dp_core, while retaining unused structure definition.
Later on the driver was reworked and the definition migrated
to the analogix_dp driver. Remove unused struct bridge_init definition.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240520125551.11534-1-linux@treblig.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
core:
- deprecate DRM data and return 0 date
- connector: Create a set of helpers to help with HDMI support
- Remove driver owner assignments
- Allow more drivers to compile with COMPILE_TEST
- Conversions to drm_edid
- Sprinkle MODULE_DESCRIPTIONS everywhere they are missing
- Remove drm_mm_replace_node
- print: Add a drm prefix to warn level messages too, remove
___drm_dbg, consolidate prefix handling
- New monochrome TV mode variant
ttm:
- improve number of page faults on some platforms
- fix test builds under PREEMPT_RT
- more test coverage
ci:
- Require a more recent version of mesa,
- improve farm setup and test generation
dma-buf:
- warn if reserving 0 fence slots
- internal API heap enhancements
fbdev:
- Create memory manager optimized fbdev emulation
panic:
- Allow to select fonts,
- improve drm_fb_dma_get_scanout_buffer
- Allow to dump kmsg to the screen
bridge:
- Remove redundant checks on bridge->encoder
- Remove drm_bridge_chain_mode_fixup
- bridge-connector: Plumb in the new HDMI helper
- analogix_dp: Various improvements, handle AUX transfers timeout
- samsung-dsim: Fix timings calculation
- tc358767: Plenty of small fixes, fix no connector attach, fix clocks
- sii902x: state validation improvements
panels:
- Switch panels from register table initialization to proper code
- Now that the panel code tracks the panel state, remove every
ad-hoc implementation in the panel drivers
- More cleanup of prepare / enable state tracking in drivers
- edp: Drop legacy panel compatibles
- simple-bridge: Switch to devm_drm_bridge_add
- New panels: Lincoln Tech Sol LCD185-101CT, Microtips Technology
13-101HIEBCAF0-C, Microtips Technology MF-103HIEB0GA0, BOE
nv110wum-l60, IVO t109nw41, WL-355608-A8, PrimeView PM070WL4,
Lincoln Technologies LCD197, Ortustech COM35H3P70ULC,
AUO G104STN01, K&d kd101ne3-40ti
amdgpu:
- DCN 4.0.x support
- GC 12.0 support
- GMC 12.0 support
- SDMA 7.0 support
- MES12 support
- MMHUB 4.1 support
- GFX12 modifier and DCC support
- lots of IP fixes/updates
amdkfd:
- Contiguous VRAM allocations
- GC 12.0 support
- SDMA 7.0 support
- SR-IOV fixes
- KFD GFX ALU exceptions
i915:
- Battlemage Xe2 HPD display enablement
- Panel Replay enabling
- DP AUX-less ALPM/LOBF
- Enable link training failure fallback for DP MST links
- CMRR (Content Match Refresh Rate) enabling
- Increase ADL-S/ADL-P/DG2+ max TMDS bitrate to 6 Gbps
- Enable eDP AUX based HDR backlight
- Support replaying GPU hangs with captured context image
- Automate CCS Mode setting during engine resets
- lots of refactoring
- Support replaying GPU hangs with captured context image
- Increase FLR timeout from 3s to 9s
- Enable w/a 16021333562 for DG2, MTL and ARL [guc]
xe:
- update MAINATINERS
- New uapi adding OA functionality to Xe
- expose l3 bank mask
- fix display detect on ADL-N
- runtime PM Fixes
- Fix silent backmerge issues
- More prep for SR-IOV
- HWmon additions
- per client usage info
- Rework GPU page fault handling
- Drop EXEC_QUEUE_FLAG_BANNED
- Add BMG PCI IDs
- Scheduler fixes and improvements
- Rename xe_exec_queue::compute to xe_exec_queue::lr
- Use ttm_uncached for BO with NEEDS_UC flag
- Rename xe perf layer as xe observation layer
- lots of refactoring
radeon:
- Backlight workaround for iMac
- Silence UBSAN flex array warnings
msm:
- Validate registers XML description against schema in CI
- core/dpu: SM7150 support
- mdp5: Add support for MSM8937
- gpu: Add param for userspace to know if raytracing is supported
- gpu: X185 support (aka gpu in X1 laptop chips)
- gpu: a505 support
ivpu:
- hardware scheduler support
- profiling support
- improvements to the platform support layer
- firmware handling improvements
- clocks/power mgmt improvements
- scheduler/logging improvements
habanalabs:
- Gradual sleep in polling memory macro.
- Reduce Gaudi2 MSI-X interrupt count to 128.
- Add Gaudi2-D revision support.
- Add timestamp to CPLD info.
- Gaudi2: Assume hard-reset by firmware upon MC SEI severe error.
- Align Gaudi2 interrupt names.
- Check for errors after preboot is ready.
- Change habanalabs maintainer and git repo path.
mgag200:
- refactoring and improvements
- Add BMC output
- enable polling
nouveau:
- add registry command line
v3d:
- perf counters improvements
zynqmp:
- irq and debugfs improvements
atmel-hlcdc:
- Support XLCDC in sam9x7
mipi-dbi:
- Remove mipi_dbi_machine_little_endian
- make SPI bits per word configurable
- support RGB888
- allow pixel formats to be specified in the DT
sun4i:
- Rework the blender setup for DE2
panfrost:
- Enable MT8188 support
vc4:
- Monochrome TV support
exynos:
- fix fallback mode regression
- fix memory leak
- Use drm_edid_duplicate() instead of kmemdup()
etnaviv:
- fix i.MX8MP NPU clock gating
- workaround FE register cdc issues on some cores
- fix DMA sync handling for cached buffers
- fix job timeout handling
- keep TS enabled on MMUv2 cores for improved performance
mediatek:
- Convert to platform remove callback returning void-
- Drop chain_mode_fixup call in mode_valid()
- Fixes the errors of MediaTek display driver found by IGT.
- Add display support for the MT8365-EVK board
- Fix bit depth overwritten for mtk_ovl_set bit_depth()
- Fix possible_crtcs calculation
- Fix spurious kfree()
ast:
- refactor mode setting code
stm:
- Add LVDS support
- DSI PHY updates
-----BEGIN PGP SIGNATURE-----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=g+Ad
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-07-18' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"There's a lot of stuff in here, amd, i915 and xe have new platform
work, lots of core rework around EDID handling, some new COMPILE_TEST
options, maintainer changes and a lots of other stuff. Summary:
core:
- deprecate DRM data and return 0 date
- connector: Create a set of helpers to help with HDMI support
- Remove driver owner assignments
- Allow more drivers to compile with COMPILE_TEST
- Conversions to drm_edid
- Sprinkle MODULE_DESCRIPTIONS everywhere they are missing
- Remove drm_mm_replace_node
- print: Add a drm prefix to warn level messages too, remove
___drm_dbg, consolidate prefix handling
- New monochrome TV mode variant
ttm:
- improve number of page faults on some platforms
- fix test builds under PREEMPT_RT
- more test coverage
ci:
- Require a more recent version of mesa
- improve farm setup and test generation
dma-buf:
- warn if reserving 0 fence slots
- internal API heap enhancements
fbdev:
- Create memory manager optimized fbdev emulation
panic:
- Allow to select fonts
- improve drm_fb_dma_get_scanout_buffer
- Allow to dump kmsg to the screen
bridge:
- Remove redundant checks on bridge->encoder
- Remove drm_bridge_chain_mode_fixup
- bridge-connector: Plumb in the new HDMI helper
- analogix_dp: Various improvements, handle AUX transfers timeout
- samsung-dsim: Fix timings calculation
- tc358767: Plenty of small fixes, fix no connector attach, fix
clocks
- sii902x: state validation improvements
panels:
- Switch panels from register table initialization to proper code
- Now that the panel code tracks the panel state, remove every ad-hoc
implementation in the panel drivers
- More cleanup of prepare / enable state tracking in drivers
- edp: Drop legacy panel compatibles
- simple-bridge: Switch to devm_drm_bridge_add
- New panels: Lincoln Tech Sol LCD185-101CT, Microtips Technology
13-101HIEBCAF0-C, Microtips Technology MF-103HIEB0GA0,
BOE nv110wum-l60, IVO t109nw41, WL-355608-A8, PrimeView
PM070WL4, Lincoln Technologies LCD197, Ortustech
COM35H3P70ULC, AUO G104STN01, K&d kd101ne3-40ti
amdgpu:
- DCN 4.0.x support
- GC 12.0 support
- GMC 12.0 support
- SDMA 7.0 support
- MES12 support
- MMHUB 4.1 support
- GFX12 modifier and DCC support
- lots of IP fixes/updates
amdkfd:
- Contiguous VRAM allocations
- GC 12.0 support
- SDMA 7.0 support
- SR-IOV fixes
- KFD GFX ALU exceptions
i915:
- Battlemage Xe2 HPD display enablement
- Panel Replay enabling
- DP AUX-less ALPM/LOBF
- Enable link training failure fallback for DP MST links
- CMRR (Content Match Refresh Rate) enabling
- Increase ADL-S/ADL-P/DG2+ max TMDS bitrate to 6 Gbps
- Enable eDP AUX based HDR backlight
- Support replaying GPU hangs with captured context image
- Automate CCS Mode setting during engine resets
- lots of refactoring
- Support replaying GPU hangs with captured context image
- Increase FLR timeout from 3s to 9s
- Enable w/a 16021333562 for DG2, MTL and ARL [guc]
xe:
- update MAINATINERS
- New uapi adding OA functionality to Xe
- expose l3 bank mask
- fix display detect on ADL-N
- runtime PM Fixes
- Fix silent backmerge issues
- More prep for SR-IOV
- HWmon additions
- per client usage info
- Rework GPU page fault handling
- Drop EXEC_QUEUE_FLAG_BANNED
- Add BMG PCI IDs
- Scheduler fixes and improvements
- Rename xe_exec_queue::compute to xe_exec_queue::lr
- Use ttm_uncached for BO with NEEDS_UC flag
- Rename xe perf layer as xe observation layer
- lots of refactoring
radeon:
- Backlight workaround for iMac
- Silence UBSAN flex array warnings
msm:
- Validate registers XML description against schema in CI
- core/dpu: SM7150 support
- mdp5: Add support for MSM8937
- gpu: Add param for userspace to know if raytracing is supported
- gpu: X185 support (aka gpu in X1 laptop chips)
- gpu: a505 support
ivpu:
- hardware scheduler support
- profiling support
- improvements to the platform support layer
- firmware handling improvements
- clocks/power mgmt improvements
- scheduler/logging improvements
habanalabs:
- Gradual sleep in polling memory macro
- Reduce Gaudi2 MSI-X interrupt count to 128
- Add Gaudi2-D revision support
- Add timestamp to CPLD info
- Gaudi2: Assume hard-reset by firmware upon MC SEI severe error
- Align Gaudi2 interrupt names
- Check for errors after preboot is ready
- Change habanalabs maintainer and git repo path
mgag200:
- refactoring and improvements
- Add BMC output
- enable polling
nouveau:
- add registry command line
v3d:
- perf counters improvements
zynqmp:
- irq and debugfs improvements
atmel-hlcdc:
- Support XLCDC in sam9x7
mipi-dbi:
- Remove mipi_dbi_machine_little_endian
- make SPI bits per word configurable
- support RGB888
- allow pixel formats to be specified in the DT
sun4i:
- Rework the blender setup for DE2
panfrost:
- Enable MT8188 support
vc4:
- Monochrome TV support
exynos:
- fix fallback mode regression
- fix memory leak
- Use drm_edid_duplicate() instead of kmemdup()
etnaviv:
- fix i.MX8MP NPU clock gating
- workaround FE register cdc issues on some cores
- fix DMA sync handling for cached buffers
- fix job timeout handling
- keep TS enabled on MMUv2 cores for improved performance
mediatek:
- Convert to platform remove callback returning void-
- Drop chain_mode_fixup call in mode_valid()
- Fixes the errors of MediaTek display driver found by IGT
- Add display support for the MT8365-EVK board
- Fix bit depth overwritten for mtk_ovl_set bit_depth()
- Fix possible_crtcs calculation
- Fix spurious kfree()
ast:
- refactor mode setting code
stm:
- Add LVDS support
- DSI PHY updates"
* tag 'drm-next-2024-07-18' of https://gitlab.freedesktop.org/drm/kernel: (2501 commits)
drm/amdgpu/mes12: add missing opcode string
drm/amdgpu/mes11: update opcode strings
Revert "drm/amd/display: Reset freesync config before update new state"
drm/omap: Restrict compile testing to PAGE_SIZE less than 64KB
drm/xe: Drop trace_xe_hw_fence_free
drm/xe/uapi: Rename xe perf layer as xe observation layer
drm/amdgpu: remove exp hw support check for gfx12
drm/amdgpu: timely save bad pages to eeprom after gpu ras reset is completed
drm/amdgpu: flush all cached ras bad pages to eeprom
drm/amdgpu: select compute ME engines dynamically
drm/amd/display: Allow display DCC for DCN401
drm/amdgpu: select compute ME engines dynamically
drm/amdgpu/job: Replace DRM_INFO/ERROR logging
drm/amdgpu: select compute ME engines dynamically
drm/amd/pm: Ignore initial value in smu response register
drm/amdgpu: Initialize VF partition mode
drm/amd/amdgpu: fix SDMA IRQ client ID <-> req mapping
MAINTAINERS: fix Xinhui's name
MAINTAINERS: update powerplay and swsmu
drm/qxl: Pin buffer objects for internal mappings
...
In the process of adding support for shared IRQ pins, a scenario
was accidentally created where adv7511_irq_process returned
prematurely causing the EDID to fail randomly.
Since the interrupt handler is broken up into two main helper functions,
update both of them to treat the helper functions as IRQ handlers. These
IRQ routines process their respective tasks as before, but if they
determine that actual work was done, mark the respective IRQ status
accordingly, and delay the check until everything has been processed.
This should guarantee the helper functions don't return prematurely
while still returning proper values of either IRQ_HANDLED or IRQ_NONE.
Reported-by: Liu Ying <victor.liu@nxp.com>
Fixes: f3d9683346 ("drm/bridge: adv7511: Allow IRQ to share GPIO pins")
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Liu Ying <victor.liu@nxp.com> # i.MX8MP EVK ADV7535 EDID retrieval w/o IRQ
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240630221931.1650565-1-aford173@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
V3: Remove unnecessary declaration of ret by evaluating the return
code of regmap_read directly.
V2: Fix uninitialized cec_status
Cut back a little on error handling to return either IRQ_NONE or
IRQ_HANDLED.
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmaB0NweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGkvwH/36UJRk/o6wvXnyH
E6QjCSWo2226APyWks22NjtC3I/8Iqdvkneuh6wG0qL2sXAB078EMjUq5R81bF8H
wWFBJwetjYTp8GEyLioMEb2wCH/J3R29dLFC4UYTplafXRGP6//xcpJaKmTxcgdR
31IzvTPXbApZ7L3k1U6rA2bK9PNKcFCOvZlrNMUCuwMrabymHsDfOUt1DqXyg2xp
zjqiWYBwlklozmgawSWt/mdEgkWuTcAbg+KyqDVQF59s9aj/OOwZ0j+HACq5V8CM
quTPIAYL6CC9p7uxa69lGr/sgC0Is/BZLPX7RTZAwCgarGvnX+1HUsjDcaFCtrVg
O6fPUV8=
=pgUx
-----END PGP SIGNATURE-----
Merge v6.10-rc6 into drm-next
The exynos-next pull is based on a newer -rc than drm-next. hence
backmerge first to make sure the unrelated conflicts we accumulated
don't end up randomly in the exynos merge pull, but are separated out.
Conflicts are all benign: Adjacent changes in amdgpu and fbdev-dma
code, and cherry-pick conflict in xe.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Timeouts on the AUX bus are to be expected in certain normal operating
conditions. There is no need to raise an error log or re-initialize the
whole AUX state machine. Simply acknowledge the AUX_ERR interrupt and
let upper layers know about the timeout.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-14-l.stach@pengutronix.de
All AUX error responses raise the AUX_ERR interrupt, so there is no
need to read the AUX status register in normal operation. Only read
the status when an error occurred and we can expect a different
status than OK.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-13-l.stach@pengutronix.de
Move the wait loop into its own function, so it doesn't need to be
replicated in multiple locations. Also move the PLL lock checks between
setting the link bandwidth, which may cause the PLL to unlock, and the
MACRO_RST which needs the PLL to be locked.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-12-l.stach@pengutronix.de
The PLL will be reconfigured later, which may cause it to go out of lock
anyway, so there is no point in waiting for the PLL to lock here. Instead
we can continue execution of the link setup, which will properly set the
PLL parameters and will wait for the PLL to lock at the appropriate times.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-11-l.stach@pengutronix.de
Setting the link bandwidth may change the PLL parameters, which will cause
the PLL to go out of lock, so make sure to apply the MACRO_RST, which
according to the comment is required to be pulsed after the PLL is locked.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-10-l.stach@pengutronix.de
This check is way too late in the DP enable flow. The PLL must be
locked much earlier, before any link training can happen. If the
PLL is unlocked at that point in time there is something seriously
wrong in the enable flow.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Robet Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-9-l.stach@pengutronix.de
Make sure the controller is in a basic working state after runtime
resume. Keep the analog function enable in the mode set path as this
enables parts of the PHY that are only required to be powered when
there is a data stream being sent out.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-8-l.stach@pengutronix.de
Platform and PHY power isn't only required when the actual display data
stream is active, but may be required earlier to support AUX channel
transactions. Move them into the runtime PM calls, so they are properly
managed whenever various other parts of the driver need them to be active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-7-l.stach@pengutronix.de
The clock is already managed by runtime PM, which is properly invoked
from the analogix_dp_set_bridge function, so there is no need for an
additional reference.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-6-l.stach@pengutronix.de
Now that the clock is handled dynamically through
analogix_dp_resume/suspend and it isn't statically enabled in the
driver probe routine, there is no need for the remove function anymore.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-5-l.stach@pengutronix.de
There is no reason to enable the controller clock in driver probe, as
there is no HW initialization done in this function. Instead rely on
either runtime PM to handle the controller clock or statically enable
it in the driver bind routine, after which real hardware access is
required to work.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-4-l.stach@pengutronix.de
AUX transactions require the controller to be in working state and
take a runtime PM reference. To avoid potential races beween the
first transactions on the bus and runtime PM being set up, move the
AUX registration behind the runtime PM setup.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-3-l.stach@pengutronix.de
This isn't used, but gives the impression of the power on and power off
platform calls being non-symmetrical. Remove the unused callback and
rename the power_on_start to simply power_on.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-1-l.stach@pengutronix.de
This reverts commit 01338bb82f.
With clock improvements in place, this seems to be no longer
necessary. Set the CLRSIPO to default setting recommended by
manufacturer.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625120334.145320-5-marex@denx.de
The only information in the datasheet regarding this divider is a note
in SYS_PLLPARAM register documentation which states that when LSCLK is
270 MHz, LSCLK_DIV should be 1. What should LSCLK_DIV be set to when
LSCLK is 162 MHz (for DP 1.62G mode) is unclear, but empirical test
confirms using LSCLK_DIV 1 has no adverse effects either. In the worst
case, the internal TC358767 clock would run faster.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625120334.145320-4-marex@denx.de
This line_pixel_subtract is no longer needed now that the bridge can
request and obtain specific pixel clock on input to the bridge, with
clock frequency that matches the Pixel PLL frequency.
The line_pixel_subtract is now always 0, so drop it entirely.
The line_pixel_subtract was not reliable as it never worked when the
Pixel PLL and input clock were off just so that the required amount
of pixels to subtract would not be whole integer.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625120334.145320-3-marex@denx.de
Use tc_pxl_pll_calc() to find out the exact clock frequency generated by the
Pixel PLL. Use the Pixel PLL frequency as adjusted_mode clock frequency and
pass it down the display pipeline to obtain exactly this frequency on input
into this bridge.
The precise input frequency that matches the Pixel PLL frequency is
important for this bridge, as if the frequencies do not match, the
bridge does suffer VFIFO overruns or underruns.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625120334.145320-2-marex@denx.de
Split tc_pxl_pll_en() into tc_pxl_pll_calc() which does only Pixel PLL
parameter calculation and tc_pxl_pll_en() which calls tc_pxl_pll_calc()
and then configures the Pixel PLL register.
This is a preparatory patch for further rework, where tc_pxl_pll_calc()
will also be used to find out the exact clock frequency generated by the
Pixel PLL. This frequency will be used as adjusted_mode clock frequency
and passed down the display pipeline to obtain exactly this frequency
on input into this bridge.
The precise input frequency that matches the Pixel PLL frequency is
important for this bridge, as if the frequencies do not match, the
bridge does suffer VFIFO overruns or underruns.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625120334.145320-1-marex@denx.de
With new connector model, tc358767 will not create the connector, when
DRM_BRIDGE_ATTACH_NO_CONNECTOR is set and display-controller driver will
rely on format negotiation to setup the encoder format.
Add the missing bus format negotiation hooks in the
drm_bridge_funcs to complete DRM_BRIDGE_ATTACH_NO_CONNECTOR support.
Output format, for DPI/DSI to DP, is selected to
MEDIA_BUS_FMT_RGB888_1X24 as default, keeping in mind what the older
model used to support.
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Closes: https://lore.kernel.org/all/24282420-b4dd-45b3-bb1c-fc37fe4a8205@siemens.com/
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231108-tc358767-v2-1-25c5f70a2159@ideasonboard.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
simple_bridge_probe() calls drm_bridge_add()
Thus, drm_bridge_remove() must be called in the remove() callback.
If we call devm_drm_bridge_add() instead, then drm_bridge_remove()
will be called automatically at device release, and the remove()
callback is no longer required.
Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240618-devm-simple-bridge-v1-1-c7ed8a09fcc5@freebox.fr
Check the pixel clock for the mode in atomic_check and ensure that
it is within the range supported by the bridge.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240613083805.439337-4-j-choudhary@ti.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Change exisitig enable() and disable() bridge hooks to their atomic
counterparts as the former hooks are deprecated.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240613083805.439337-3-j-choudhary@ti.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Currently, mode_valid is defined only in drm_connector_helper_funcs.
When the bridge is attached with the 'DRM_BRIDGE_ATTACH_NO_CONNECTOR'
flag, the connector is not initialized, and so is the mode_valid
hook under connector helper funcs.
It also returns MODE_OK for all modes without actually checking the
modes.
So move the mode_valid hook to drm_bridge_funcs with proper clock
checks for maximum and minimum pixel clock supported by the bridge.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240613083805.439337-2-j-choudhary@ti.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The spec of timing between IVDD/OVDD and SYSRTEN is 10ms, but SYSRSTN RC
circuit need at least 25ms for rising time, update for match spec
Signed-off-by: Kuro Chung <kuro.chung@ite.com.tw>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240604024405.1122488-1-kuro.chung@ite.com.tw
The VFP, HBP, and HSA are divided between the available lanes if
there is more than one lane. For certain timings and lane
configurations, the HFP may not be evenly divisible. If the HFP
is rounded down, it ends up being too small which can cause some
monitors to not sync properly. In these instances, adjust htotal
and hsync to round the HFP up, and recalculate the htotal.
This allows 720P-60 to operation on an i.MX8MP with a four-lane
configuration.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> # Kontron BL i.MX8MM with HDMI monitor
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240601144103.198299-2-aford173@gmail.com
The P divider should be set based on the min and max values of
the fin pll which may vary between different platforms.
These ranges are defined per platform, but hard-coded values
were used instead which resulted in a smaller range available
on the i.MX8M[MNP] than what was possible.
As noted by Frieder, there are descripencies between the reference
manuals of the Mini, Nano and Plus, so I reached out to my NXP
rep and got the following response regarding the varing notes
in the documentation.
"Yes it is definitely wrong, the one that is part of the NOTE in
MIPI_DPHY_M_PLLPMS register table against PMS_P, PMS_M and PMS_S is
not correct. I will report this to Doc team, the one customer should
be take into account is the Table 13-40 DPHY PLL Parameters and the
Note above."
With this patch, the clock rates now match the values used in NXP's
downstream kernel.
Fixes: 846307185f ("drm/bridge: samsung-dsim: update PLL reference clock")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240601144103.198299-1-aford173@gmail.com
Make sure the connector is fully initialized before signalling any
HPD events via drm_kms_helper_hotplug_event(), otherwise this may
lead to NULL pointer dereference.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240531203333.277476-1-marex@denx.de
Fix comment copy-paste error in tc_edp_mode_valid(), this function
is validating DP/eDP clock, not DPI clock frequency. Update the
comment to match. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240531203213.277421-1-marex@denx.de
Device managed panel bridge wrappers are created by calling to
drm_panel_bridge_add_typed() and registering a release handler for
clean-up when the device gets unbound.
Since the memory for this bridge is also managed and linked to the panel
device, the release function should not try to free that memory.
Moreover, the call to devm_kfree() inside drm_panel_bridge_remove() will
fail in this case and emit a warning because the panel bridge resource
is no longer on the device resources list (it has been removed from
there before the call to release handlers).
Fixes: 67022227ff ("drm/bridge: Add a devm_ allocator for panel bridge.")
Signed-off-by: Adam Miotk <adam.miotk@arm.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610102739.139852-1-adam.miotk@arm.com
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpu/drm/bridge/lontium-lt9611.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpu/drm/bridge/lontium-lt9611uxc.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpu/drm/bridge/sil-sii8620.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpu/drm/bridge/sii9234.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240609-md-drivers-gpu-drm-bridge-v1-1-b582c5c815d7@quicinc.com
Take a early return from the clock recovery training when the sink reports
CR_DONE for all lanes. There is no point in trying to adjust the link
parameters further.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240318203925.2837689-3-l.stach@pengutronix.de
There is no need for separate functions for each lane, as we can deduct the
register offset to read/write from the lane index.
Signed-off-by: Wyon Bi <bivvy.bi@rock-chips.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240318203925.2837689-2-l.stach@pengutronix.de
