Add connector debugfs entries to force the link rate/lane count to be
used by a link training afterwards. These settings will be clamped to
the supported, i.e. the source's and sink's common rate/lane count.
After forcing the link rate/lane count reset the link training
parameters and for a non-auto setting disable reducing the link
parameters via the fallback logic. The former one can be used after
testing link training failure scenarios - via debugfs entries added
later - to reset the reduced link parameters after the test.
v2:
- Add the entries from intel_dp_link_training.c (Jani)
- Rename the entries to i915_dp_set_link_rate/lane_count.
v3: (Ville)
- Rename the entries/struct fields to force_link_rate/lane_count.
- Lock connection_mutex only for the required intel_dp state.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-18-imre.deak@intel.com
The next patch adds sending a modeset-retry uevent after a link training
failure to all MST connectors on link. This requires the atomic state,
so pass it to intel_dp_start_link_train(). In case of SST where
retraining still happens by calling this function directly instead of a
modeset commit the atomic state is not available and NULL is passed
instead. This is ok, since in this case the encoder's only DP connector
is available from intel_dp->attached_connector not requiring the atomic
state.
v2: Add NOTE that the atomic state may not be valid for SST links and
assert that it's valid for MST links. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-10-imre.deak@intel.com
Factor out a function to read the sink's DPRX capabilities used by a
follow-up patch enabling the DP tunnel BW allocation mode.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-10-imre.deak@intel.com
Enable SDP error detection configuration, this will set CRC16 in
128b/132b link layer.
For Display version 13 a hardware bit31 in register VIDEO_DIP_CTL is
added to enable/disable SDP CRC applicable for DP2.0 only, but the
default value of this bit will enable CRC16 in 128b/132b hence
skipping this write.
Corrective actions on SDP corruption is yet to be defined.
v2: Moved the CRC enable to link training init(Jani N)
v3: Moved crc enable to ddi pre enable <Jani N>
v4: Separate function for SDP CRC16 (Jani N)
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230302081532.765821-3-arun.r.murthy@intel.com
Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.
Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.
v2:
* update commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-3-tzimmermann@suse.de
UAPI Changes:
- Weak parallel submission support for execlists
Minimal implementation of the parallel submission support for
execlists backend that was previously only implemented for GuC.
Support one sibling non-virtual engine.
Core Changes:
- Two backmerges of drm/drm-next for header file renames/changes and
i915_regs reorganization
Driver Changes:
- Add new DG2 subplatform: DG2-G12 (Matt R)
- Add new DG2 workarounds (Matt R, Ram, Bruce)
- Handle pre-programmed WOPCM registers for DG2+ (Daniele)
- Update guc shim control programming on XeHP SDV+ (Daniele)
- Add RPL-S C0/D0 stepping information (Anusha)
- Improve GuC ADS initialization to work on ARM64 on dGFX (Lucas)
- Fix KMD and GuC race on accessing PMU busyness (Umesh)
- Use PM timestamp instead of RING TIMESTAMP for reference in PMU with GuC (Umesh)
- Report error on invalid reset notification from GuC (John)
- Avoid WARN splat by holding RPM wakelock during PXP unbind (Juston)
- Fixes to parallel submission implementation (Matt B.)
- Improve GuC loading status check/error reports (John)
- Tweak TTM LRU priority hint selection (Matt A.)
- Align the plane_vma to min_page_size of stolen mem (Ram)
- Introduce vma resources and implement async unbinding (Thomas)
- Use struct vma_resource instead of struct vma_snapshot (Thomas)
- Return some TTM accel move errors instead of trying memcpy move (Thomas)
- Fix a race between vma / object destruction and unbinding (Thomas)
- Remove short-term pins from execbuf (Maarten)
- Update to GuC version 69.0.3 (John, Michal Wa.)
- Improvements to GT reset paths in GuC backend (Matt B.)
- Use shrinker_release_pages instead of writeback in shmem object hooks (Matt A., Tvrtko)
- Use trylock instead of blocking lock when freeing GEM objects (Maarten)
- Allocate intel_engine_coredump_alloc with ALLOW_FAIL (Matt B.)
- Fixes to object unmapping and purging (Matt A)
- Check for wedged device in GuC backend (John)
- Avoid lockdep splat by locking dpt_obj around set_cache_level (Maarten)
- Allow dead vm to unbind vma's without lock (Maarten)
- s/engine->i915/i915/ for DG2 engine workarounds (Matt R)
- Use to_gt() helper for GGTT accesses (Michal Wi.)
- Selftest improvements (Matt B., Thomas, Ram)
- Coding style and compiler warning fixes (Matt B., Jasmine, Andi, Colin, Gustavo, Dan)
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Yg4i2aCZvvee5Eai@jlahtine-mobl.ger.corp.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Fixed conflicts while applying, using the fixups/drm-intel-gt-next.patch
from drm-rerere's 1f2b1742abdd ("2022y-02m-23d-16h-07m-57s UTC: drm-tip
rerere cache update")]
By the specification the 0xF0000-0xF02FF range is only valid when the
DPCD revision is 1.4 or higher. Disable LTTPR support if this isn't so.
Trying to detect LTTPRs returned corrupted values for the above DPCD
range at least on a Skylake host with an LG 43UD79-B monitor with a DPCD
revision 1.2 connected.
v2: Add the actual version check.
v3: Fix s/DRPX/DPRX/ typo.
Fixes: 7b2a4ab8b0 ("drm/i915: Switch to LTTPR transparent mode link training")
Cc: <stable@vger.kernel.org> # v5.11
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210317190149.4032966-1-imre.deak@intel.com
The DP PHY vswing/pre-emphasis level programming the driver does is
related to the DPTX -> first LTTPR link segment only. Accordingly it
should be only programmed when link training the first LTTPR and kept
as-is when training subsequent LTTPRs and the DPRX. For these latter
PHYs the vs/pe levels will be set in response to writing the
DP_TRAINING_LANEx_SET_PHY_REPEATERy DPCD registers (by an upstream LTTPR
TX PHY snooping this write access of its downstream LTTPR/DPRX RX PHY).
The above is also described in DP Standard v2.0 under 3.6.6.1.
While at it simplify and add the LTTPR that is link trained to the debug
message in intel_dp_set_signal_levels().
Fixes: b30edfd8d0 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201229172201.4155327-2-imre.deak@intel.com
The DP Standard's recommendation is to use the LTTPR non-transparent
mode link training if LTTPRs are detected, so let's do this.
Besides power-saving, the advantages of this are that the maximum number
of LTTPRs can only be used in non-transparent mode (the limit is 5-8 in
transparent mode), and it provides a way to narrow down the reason for a
link training failure to a given link segment. Non-transparent mode is
probably also the mode that was tested the most by the industry.
The changes in this patchset:
- Pass the DP PHY that is currently link trained to all LT helpers, so
that these can access the correct LTTPR/DPRX DPCD registers.
- During LT take into account the LTTPR common lane rate/count and the
per LTTPR-PHY vswing/pre-emph limits.
- Switch to LTTPR non-transparent LT mode and train each link segment
according to the sequence in DP Standard v2.0 (complete CR/EQ for
each segment before continuing with the next segment).
v2:
- Switch to non-transparent mode during connector detection, which is
required before reading the per-PHY LTTPR capabilities.
- Move the DP_PHY_LTTPR() macro to drm_dp_helper.h (Ville)
- Use the new drm_dp_dpcd_read_phy_link_status() instead of adding the
same logic to intel_dp_get_link_status(). (Ville)
- Make intel_dp_lttpr_phy_caps() return a pointer to the whole array
instead of a pointer to its first element. (Ville)
- Add the intel_dp_phy_is_downstream_of_source() helper. (Ville)
- Add a code comment about the disable->enable quirk of
non-transparent mode.
- Add the intel_dp_training_pattern_set_reg() helper.
- Fix checkpatch/sparse warns.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-7-imre.deak@intel.com
By default LTTPRs should be in transparent link training mode,
nevertheless in this patch we switch to this default mode explicitly.
The DP Standard recommends this, supposedly because an LTTPR may be left
in the non-transparent mode (by BIOS, previous kernel, or after reset
due to a firmware bug). I haven't seen this happening, but let's follow
the DP Standard.
v2:
- Add a code comment about the explicit disabling of non-transparent
mode.
v3:
- Move check to prevent initing LTTPRs on eDP to init_dp_lttpr_init().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-6-imre.deak@intel.com
An LTTPR can be trained with training pattern 4 even if the DPCD
revision is < 1.4, but drm_dp_training_pattern_mask() would change
pattern 4 to pattern 3 on those DPCD revisions.
Since intel_dp_training_pattern() makes already sure that the proper
training pattern is used, all that needs to be masked out is the
scrambling disable flag, which is or'd to the mask later based on the
training pattern.
v2:
- Use a helper instead of open-coding the masking. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-2-imre.deak@intel.com
Get rid of mode crtc->config usage, and some ad-hoc intel_dp state
usage by plumbing the crtc state all the way down to the link training
code.
Unfortunately we do have to keep some cached state in intel_dp so
that we can do the "does the link need retraining?" checks from
the short hpd handler.
v2: Add intel_crtc_state forward declaration
v3: Don't kill the PHY test code totally since it's
now in the hotplug work where we can get at the states
v4: Don't resurrect the debug scrambling disable bit (Imre)
Use intel_dp_mst_is_master_trans() (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001111053.24451-1-ville.syrjala@linux.intel.com
vswing/pre-emphasis adjustment calculation is needed in processing
of auto phy compliance request other than link training, so have
made non-static function.
No functional change.
v1: initial patch.
v2:
- used "intel_dp" prefix in function name. (Jani)
- used array notation instead pointer for link_status. (Ville)
v3: Scrapped the initial patch, modified commit description accordingly.
- made non-static function and used intel_dp prefix. (Jani, Manasi)
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-4-animesh.manna@intel.com
Add a new subdirectory for display code, and start off by moving
modesetting output/encoder code. Judging by the include changes, this is
a surprisingly clean operation.
v2:
- move intel_sdvo_regs.h too
- use tabs for Makefile file lists and sort them
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613084416.6794-2-jani.nikula@intel.com
2019-06-17 11:25:06 +03:00
Renamed from drivers/gpu/drm/i915/intel_dp_link_training.h (Browse further)
