Annotate a few more of the failure paths on the initial
BIOS fb takeover to avoid having to guess why things
aren't working the way we expect.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Tested-by: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202224340.30647-17-ville.syrjala@linux.intel.com
On MTL the GOP (for whatever reason) likes to bind its framebuffer
high up in the ggtt address space. This can conflict with whatever
ggtt_reserve_guc_top() is trying to do, and the result is that
ggtt_reserve_guc_top() fails and then we proceed to explode when
trying to tear down the driver. Thus far I haven't analyzed what
causes the actual fireworks, but it's not super important as even
if it didn't explode we'd still fail the driver load and the user
would be left with an unusable GPU.
To remedy this (without having to figure out exactly what
ggtt_reserve_guc_top() is trying to achieve) we can attempt to
relocate the BIOS framebuffer to a lower ggtt address. We can do
this at this early point in driver init because nothing else is
supposed to be clobbering the ggtt yet. So we simply change where
in the ggtt we pin the vma, the original PTEs will be left as is,
and the new PTEs will get written with the same dma addresses.
The plane will keep on scanning out from the original PTEs until
we are done with the whole process, and at that point we rewrite
the plane's surface address register to point at the new ggtt
address.
Since we don't need a specific ggtt address for the plane
(apart from needing it to land in the mappable region for
normal stolen objects) we'll just try to pin it without a fixed
offset first. It should end up at the lowest available address
(which really should be 0 at this point in the driver init).
If that fails we'll fall back to just pinning it exactly to the
origianal address.
To make sure we don't accidentlally pin it partially over the
original ggtt range (as that would corrupt the original PTEs)
we reserve the original range temporarily during this process.
v2: Try to pin explicitly to ggtt offset 0 as otherwise DG2 puts it
even higher (atm we have no PIN_LOW flag to force it low)
v3: "fix" xe
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Tested-by: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202224340.30647-16-ville.syrjala@linux.intel.com
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Currently we assume that we bind the BIOS fb exactly into the same
ggtt address where the BIOS left it. That is about to change, and
in order to keep intel_reuse_initial_plane_obj() working as intended
we need to compare the original ggtt offset (called 'base' here)
as opposed to the actual vma ggtt offset we selected. Otherwise
the first plane could change the ggtt offset, and then subsequent
planes would no longer notice that they are in fact using the same
ggtt offset that the first plane was already using. Thus the reuse
check will fail and we proceed to turn off these subsequent planes.
TODO: would probably make more sense to do the pure readout first
for all the planes, then check for fb reuse, and only then proceed
to pin the object into the final location in the ggtt...
v2: "fix" xe
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Tested-by: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202224340.30647-15-ville.syrjala@linux.intel.com
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
There's no reason the caller of intel_initial_plane_config() should
have to loop over the CRTCs. Pull the loop into the function to
make life simpler for the caller.
v2: "fix" xe
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Tested-by: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202224340.30647-13-ville.syrjala@linux.intel.com
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Declutter initial_plane_vma() a bit by pulling the lmem and smem
readout paths into their own functions.
TODO: the smem path should still be fixed to get and validate
the dma address from the pte as well
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Tested-by: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202224340.30647-12-ville.syrjala@linux.intel.com
On MTL the stolen region starts at offset 8MiB from the start of
LMEMBAR. The dma addresses are thus also offset by 8MiB. However the
mm_node/etc. is zero based, and i915_pages_create_for_stolen() will
add the appropriate region.start into the sg dma address. So when
we do the readout we need to convert the dma address read from
the PTE to be zero based as well.
Note that currently we don't take this path on MTL, but we should
and thus this needs to be fixed. For lmem this works correctly
already as the lmem region.start==0.
While at it let's also make sure the address points to somewhere within
the memory region. We don't need to check the size as
i915_gem_object_create_region_at() should later fail if the object size
exceeds the region size.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Tested-by: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202224340.30647-9-ville.syrjala@linux.intel.com
When multiple pipes are enabled by the BIOS we try to read out each
in turn. But we do the readout for the second only after the inherited
vma for the first has been rebound into its original place (and thus
the PTEs have been rewritten). Unlike the BIOS we set some high caching
bits in the PTE on MTL which confuses the readout for the second plane.
Filter out the non-address bits from the PTE value appropriately to
fix this.
I suppose it might also be possible that the BIOS would already set
some caching bits as well, in which case we'd run into this same
issue already for the first plane.
TODO:
- should abstract the PTE decoding to avoid details leaking all over
- should probably do the readout for all the planes before
we touch anything (including the PTEs) so that we truly read
out the BIOS state
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Acked-by: Nirmoy Das <nirmoy.das@intel.com>
Tested-by: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202224340.30647-8-ville.syrjala@linux.intel.com
Split out frontbuffer related declarations and static inlines from
gem/i915_gem_object.h into new gem/i915_gem_object_frontbuffer.h.
The main goal is to reduce header interdependencies. With
gem/i915_gem_object.h including display/intel_frontbuffer.h,
modification of the latter causes a whopping 300+ objects to be rebuilt,
while many of the source files actually needing it aren't explicitly
including it at all.
After the change, only 21 objects depend on display/intel_frontbuffer.h,
directly or indirectly.
Cc: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830085127.2416842-1-jani.nikula@intel.com
Need to pull in commit from drm-next (earlier in drm-intel-next):
1eca0778f4 ("drm/i915: add struct i915_dsm to wrap dsm members together")
In order to merge following patch to drm-intel-gt-next:
https://patchwork.freedesktop.org/patch/530942/?series=114925&rev=6
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Framebuffer is exposed to userspace so make sure we set
proper flags for it. Set I915_BO_PREALLOC for prealloced
fb so that ttm won't clear existing data.
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230404143100.10452-2-nirmoy.das@intel.com
In another long-overdue cleanup, add a display sub-struct to
drm_i915_private, and start moving display related members there. Start
with display funcs that need a rename anyway to not collide with the new
display member.
Add a new header under display/ for defining struct intel_display.
Rename struct drm_i915_display_funcs to intel_display_funcs while at it.
v2:
- Fix multi-line comment style (Arun)
- Use display as the member name
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d44cae096b664f7015f8c797d6dfd4964226d4f8.1661346845.git.jani.nikula@intel.com
In order to get the GSC Support merged on drm-intel-gt-next
in a clean fashion we needed this ATS-M patch to avoid
conflict in i915_pci.c:
commit 412c942bdf ("drm/i915/ats-m: add ATS-M platform info")
--
Fixing a silent conflict on drivers/gpu/drm/i915/gt/intel_gt_gmch.c:
- if (!intel_vtd_active(i915))
+ if (!i915_vtd_active(i915))
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
With the upcoming multitile support each tile will have its own
local memory. Mark the current LMEM with the suffix '0' to
emphasise that it belongs to the root tile.
Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220318233938.149744-2-andi.shyti@linux.intel.com
On integrated it looks like the GGTT base should always 1:1 maps to
somewhere within DSM. On discrete the base seems to be pre-programmed with
a normal lmem address, and is not 1:1 mapped with the base address. On
such devices probe the lmem address directly from the PTE.
v2(Ville):
- The base is actually the pre-programmed GGTT address, which is then
meant to 1:1 map to somewhere inside dsm. In the case of dgpu the
base looks to just be some offset within lmem, but this also happens
to be the exact dsm start, on dg1. Therefore we should only need to
fudge the physical address, before allocating from stolen.
- Bail if it's not located in dsm.
v3:
- Scratch that. There doesn't seem to be any relationship with the
base and PTE address, on at least DG1. Let's instead just grab the
lmem address from the PTE itself.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Nirmoy Das <nirmoy.das@linux.intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220315181425.576828-7-matthew.auld@intel.com
When system does not have mappable aperture, ggtt->mappable_end=0. In
this case if we pass PIN_MAPPABLE when pinning vma, the pinning code
will return -ENOSPC. So conditionally set PIN_MAPPABLE if HAS_GMCH().
Suggested-by: Chris P Wilson <chris.p.wilson@intel.com>
Signed-off-by: CQ Tang <cq.tang@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Ap Kamal <kamal.ap@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220315181425.576828-6-matthew.auld@intel.com
Add a generic interface for allocating an object at some specific
offset, and convert stolen over. Later we will want to hook this up to
different backends.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220315181425.576828-4-matthew.auld@intel.com
Tile4 in bspec format is 4K tile organized into
64B subtiles with same basic shape as for legacy TileY
which will be supported by Display13.
v2: - Moved Tile4 associating struct for modifier/display to
the beginning(Imre Deak)
- Removed unneeded case I915_FORMAT_MOD_4_TILED modifier
checks(Imre Deak)
- Fixed I915_FORMAT_MOD_4_TILED to be 9 instead of 12
(Imre Deak)
v3: - Rebased patch on top of new changes related to plane_caps.
- Added static assert to check that PLANE_CTL_TILING_YF
matches PLANE_CTL_TILING_4(Nanley Chery)
- Fixed naming and layout description for Tile 4 in drm uapi
header(Nanley Chery)
v4: - Extracted drm_fourcc changes to separate patch(Nanley Chery)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220118115544.15116-3-stanislav.lisovskiy@intel.com
UAPI Changes:
- Weak parallel submission support for execlists
Minimal implementation of the parallel submission support for
execlists backend that was previously only implemented for GuC.
Support one sibling non-virtual engine.
Core Changes:
- Two backmerges of drm/drm-next for header file renames/changes and
i915_regs reorganization
Driver Changes:
- Add new DG2 subplatform: DG2-G12 (Matt R)
- Add new DG2 workarounds (Matt R, Ram, Bruce)
- Handle pre-programmed WOPCM registers for DG2+ (Daniele)
- Update guc shim control programming on XeHP SDV+ (Daniele)
- Add RPL-S C0/D0 stepping information (Anusha)
- Improve GuC ADS initialization to work on ARM64 on dGFX (Lucas)
- Fix KMD and GuC race on accessing PMU busyness (Umesh)
- Use PM timestamp instead of RING TIMESTAMP for reference in PMU with GuC (Umesh)
- Report error on invalid reset notification from GuC (John)
- Avoid WARN splat by holding RPM wakelock during PXP unbind (Juston)
- Fixes to parallel submission implementation (Matt B.)
- Improve GuC loading status check/error reports (John)
- Tweak TTM LRU priority hint selection (Matt A.)
- Align the plane_vma to min_page_size of stolen mem (Ram)
- Introduce vma resources and implement async unbinding (Thomas)
- Use struct vma_resource instead of struct vma_snapshot (Thomas)
- Return some TTM accel move errors instead of trying memcpy move (Thomas)
- Fix a race between vma / object destruction and unbinding (Thomas)
- Remove short-term pins from execbuf (Maarten)
- Update to GuC version 69.0.3 (John, Michal Wa.)
- Improvements to GT reset paths in GuC backend (Matt B.)
- Use shrinker_release_pages instead of writeback in shmem object hooks (Matt A., Tvrtko)
- Use trylock instead of blocking lock when freeing GEM objects (Maarten)
- Allocate intel_engine_coredump_alloc with ALLOW_FAIL (Matt B.)
- Fixes to object unmapping and purging (Matt A)
- Check for wedged device in GuC backend (John)
- Avoid lockdep splat by locking dpt_obj around set_cache_level (Maarten)
- Allow dead vm to unbind vma's without lock (Maarten)
- s/engine->i915/i915/ for DG2 engine workarounds (Matt R)
- Use to_gt() helper for GGTT accesses (Michal Wi.)
- Selftest improvements (Matt B., Thomas, Ram)
- Coding style and compiler warning fixes (Matt B., Jasmine, Andi, Colin, Gustavo, Dan)
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Yg4i2aCZvvee5Eai@jlahtine-mobl.ger.corp.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Fixed conflicts while applying, using the fixups/drm-intel-gt-next.patch
from drm-rerere's 1f2b1742abdd ("2022y-02m-23d-16h-07m-57s UTC: drm-tip
rerere cache update")]
Get rid of the inflexible bigjoiner_linked_crtc pointer thing
and just track things as a bitmask of pipes instead. We can
also nuke the bigjoiner_slave boolean as the role of the pipe
can be determined from its position in the bitmask.
It might be possible to nuke the bigjoiner boolean as well
if we make encoder.compute_config() do the bitmask assignment
directly for the master pipe. But for now I left that alone so
that encoer.compute_config() will just flag the state as needing
bigjoiner, and the intel_atomic_check_bigjoiner() is still
responsible for determining the bitmask. But that may have to change
as the encoder may be in the best position to determine how
exactly we should populate the bitmask.
Most places that just looked at the single bigjoiner_linked_crtc
now iterate over the whole bitmask, eliminating the singular
slave pipe assumption.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203183823.22890-11-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Maarten needs backmerge to account for header file renames/changes which
landed via drm-intel-next and are interfering with his pinning work.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
GGTT is currently available both through i915->ggtt and gt->ggtt, and we
eventually want to get rid of the i915->ggtt one.
Use to_gt() for all i915->ggtt accesses to help with the future
refactoring.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211219212500.61432-5-andi.shyti@linux.intel.com
TileF(Tile4 in bspec) format is 4K tile organized into
64B subtiles with same basic shape as for legacy TileY
which will be supported by Display13.
v2: - Fixed wrong case condition(Jani Nikula)
- Increased I915_FORMAT_MOD_F_TILED up to 12(Imre Deak)
v3: - s/I915_TILING_F/TILING_4/g
- s/I915_FORMAT_MOD_F_TILED/I915_FORMAT_MOD_4_TILED/g
- Removed unneeded fencing code
v4: - Rebased, fixed merge conflict with new table-oriented
format modifier checking(Stan)
- Replaced the rest of "Tile F" mentions to "Tile 4"(Stan)
v5: - Still had to remove some Tile F mentionings
- Moved has_4tile from adlp to DG2(Ramalingam C)
- Check specifically for DG2, but not the Display13(Imre)
v6: - Moved Tile4 associating struct for modifier/display to
the beginning(Imre Deak)
- Removed unneeded case I915_FORMAT_MOD_4_TILED modifier
checks(Imre Deak)
- Fixed I915_FORMAT_MOD_4_TILED to be 9 instead of 12
(Imre Deak)
v7: - Fixed display_ver to { 13, 13 }(Imre Deak)
- Removed redundant newline(Imre Deak)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211122211420.31584-1-stanislav.lisovskiy@intel.com
