During boot-up/system resume, the TC PHY on legacy ports will be
initialized by the IOM/TCSS firmware regardless of a sink being
connected or not (as opposed to DP-alt/TBT ports, which the FW only
inits once a sink is connected).
Wait for the above initialization to complete during HW readout, so that
connecting the PHY later will already see the expected PHY ready state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-6-imre.deak@intel.com
At least restoring the MST topology during system resume needs to use
AUX before the display HW readout->sanitization sequence is complete,
but on TC ports the PHY may be in the wrong mode for this, resulting in
the AUX transfers to fail.
The initial TC port mode is kept fixed as BIOS left it for the above HW
readout sequence (to prevent changing the mode on an enabled port). If
the port is disabled this initial mode is TBT - as in any case the PHY
ownership is not held - even if a DP-alt sink is connected. Thus, the
AUX transfers during this time will use TBT mode instead of the expected
DP-alt mode and so time out.
Fix the above by connecting the PHY during port initialization if the
port is disabled, which will switch to the expected mode (DP-alt in the
above case).
As the encoder/pipe HW state isn't read-out yet at this point, check if
the port is enabled based on the DDI_BUF enabled flag. Save the read-out
initial mode, so intel_tc_port_sanitize_mode() can check this wrt. the
read-out encoder HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-5-imre.deak@intel.com
The commit renaming icl_tc_phy_is_in_safe_mode() to
icl_tc_phy_take_ownership() didn't flip the function's return value
accordingly, fix this up.
This didn't cause an actual problem besides state check errors, since
the function is only used during HW readout.
Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: f53979d68a ("drm/i915/display/tc: Rename safe_mode functions ownership")
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-4-imre.deak@intel.com
An enabled TC MST port holds one TC port link reference, regardless of
the number of enabled streams on it, but the TC port HW readout takes
one reference for each active MST stream.
Fix the HW readout, taking only one reference for MST ports.
This didn't cause an actual problem, since the encoder HW readout doesn't
yet support reading out the MST HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-3-imre.deak@intel.com
On TC ports the 4ms AUX timeout combined with the 5 * 32 retry
attempts during DPCD accesses adds a 640ms delay to each access if the
sink is disconnected. This in turn slows down a modeset during which the
sink is disconnected (for instance a disabling modeset).
Prevent the above delay by aborting AUX transfers on a TC port with a
disconnected sink.
The DP 1.4a link CTS (4.2.1.5 Source Device Inactive HPD / Inactive AUX
Test") also requires not to initiate AUX transfers on disconnected DP
ports in general, however this patch doesn't change the behavior on
non-TC ports, leaving that for a follow-up.
Reported-and-tested-by: Chris Chiu <chris.chiu@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8279
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-2-imre.deak@intel.com
Move the TypeC DKL PHY register definitions to intel_dkl_phy_regs.h.
No functional changes.
v2:
- Move the definitions to a new intel_dkl_phy_regs.h file. (Jani).
v3:
- Rebase on latest patchset version.
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025114457.2191004-2-imre.deak@intel.com
An upcoming patch moves the DKL PHY register definitions to
intel_dkl_phy_regs.h, so for consistency rename intel_tc_phy_regs.h
containing only MG PHY register definitions to intel_mg_phy_regs.h.
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025102644.2123988-3-imre.deak@intel.com
During system resume DP MST requires AUX to be working already before
the HW state readout of the given encoder. Since AUX requires the
encoder/PHY TypeC mode to be initialized, which atm only happens during
HW state readout, these AUX transfers can change the TypeC mode
incorrectly (disconnecting the PHY for an enabled encoder) and trigger
the state check WARNs in intel_tc_port_sanitize().
Fix this by initializing the TypeC mode earlier both during driver
loading and system resume and making sure that the mode can't change
until the encoder's state is read out. While at it add the missing
DocBook comments and rename
intel_tc_port_sanitize()->intel_tc_port_sanitize_mode() for consistency.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922172148.2913088-1-imre.deak@intel.com
Commit 30e114ef4b ("drm/i915/tc: Check for DP-alt, legacy sinks before
taking PHY ownership") defaults any disconnected Type-C ports to TBT-alt
mode which presents a problem (which could most likely result in a system
hang) when userspace forces a modeset on a Type-C port that is wired for
legacy HDMI. The following warning is seen when Weston forces a modeset
on a disconnected legacy Type-C port (HDMI) on a TGL based Gigabyte system:
(https://www.gigabyte.com/Mini-PcBarebone/GB-BSi3-1115G4-rev-10#ov)
Missing case (clock == 173000)
WARNING: CPU: 1 PID: 438 at drivers/gpu/drm/i915/display/intel_ddi.c:245
icl_ddi_tc_enable_clock.cold+0x16a/0x1cf [i915]
CPU: 1 PID: 438 Comm: kworker/u8:3 Tainted: G U W E
5.18.0-rc5-drm-tip+ #20
Hardware name: GIGABYTE GB-BSi3-1115G4/GB-BSi3-1115G4, BIOS F9
10/16/2021
Workqueue: i915_modeset intel_atomic_commit_work [i915]
RIP: 0010:icl_ddi_tc_enable_clock.cold+0x16a/0x1cf [i915]
Code: 74 6c 7f 10 81 fd d0 78 02 00 74 6d 81 fd b0 1e 04 00 74 70 48 63
d5 48 c7 c6 c0 7b ab c0 48 c7 c7 20 75 ab c0 e8 b8 b5 c1 f0 <0f> 0b 45
31 ed e9 fb fe ff ff 49 63 d5
48 c7 c6 80 7b ab c0 48 c7
RSP: 0018:ffff8882522c78f0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000003 RCX: 0000000000000000
RDX: 0000000000000027 RSI: 0000000000000004 RDI: ffffed104a458f10
RBP: 0000000000011558 R08: ffffffffb078de4e R09: ffff888269ca748b
R10: ffffed104d394e91 R11: 0000000000000000 R12: ffff888255a318f8
R13: 0000000000000002 R14: ffff888255a30000 R15: ffff88823ef00348
FS: 0000000000000000(0000) GS:ffff888269c80000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd7afa42000 CR3: 0000000255c02004 CR4: 00000000007706e0
PKRU: 55555554
Call Trace:
<TASK>
intel_ddi_pre_enable.cold+0x96/0x5bf [i915]
intel_encoders_pre_enable+0x10e/0x140 [i915]
hsw_crtc_enable+0x207/0x99d [i915]
? ilk_crtc_enable.cold+0x2a/0x2a [i915]
? prepare_to_wait_exclusive+0x120/0x120
intel_enable_crtc+0x9a/0xf0 [i915]
skl_commit_modeset_enables+0x466/0x820 [i915]
? intel_commit_modeset_enables+0xd0/0xd0 [i915]
? intel_mbus_dbox_update+0x1ed/0x250 [i915]
intel_atomic_commit_tail+0xf2d/0x3040 [i915]
_raw_spin_lock_irqsave+0x87/0xe0
_raw_read_unlock_irqrestore+0x40/0x40
__update_load_avg_cfs_rq+0x70/0x5c0
__i915_sw_fence_complete+0x85/0x3b0 [i915]
? intel_get_crtc_new_encoder+0x190/0x190 [i915]
? sysvec_irq_work+0x13/0x90
? asm_sysvec_irq_work+0x12/0x20
? _raw_spin_lock_irq+0x82/0xd0
? read_word_at_a_time+0xe/0x20
? process_one_work+0x393/0x690
process_one_work+0x393/0x690
worker_thread+0x2b7/0x620
? process_one_work+0x690/0x690
kthread+0x15a/0x190
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
Continuing with the modeset without setting the DDI clock results in
more warnings and eventually a system hang. This does not seem to
happen with disconnected legacy or DP-alt DP ports because the clock
rate defaults to 162000 (which is a valid TBT clock) during the link
training process. Therefore, to fix this issue, this patch avoids
setting disconnected Type-C legacy ports to TBT-alt mode which prevents
the selection of TBT PLL when a modeset is forced.
v2: (Imre)
- Retain the check for legacy hotplug live status to account for
incorrect VBTs.
Cc: Imre Deak <imre.deak@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220526001939.4031112-2-vivek.kasireddy@intel.com
Atm the port -> DDI and AUX power domain mapping is specified by relying
on the aliasing of the platform specific intel_display_power_domain enum
values. For instance D12+ platforms refer to the 'D' port and power
domain instances, which doesn't match the bspec terminology, on these
platforms the corresponding port is TC1. To make it clear what
port/domain the code refers to add a mapping between them which matches
the bspec terms on different display versions.
This also allows for removing the aliasing in enum values in a follow-up
patch.
v2: Add the functions to intel_display_power.c, use
intel_display_power_ prefix.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-14-imre.deak@intel.com
BIOS may leave a TypeC PHY in a connected state even though the
corresponding port is disabled. This will prevent any hotplug events
from being signalled (after the monitor deasserts and then reasserts its
HPD) until the PHY is disconnected and so the driver will not detect a
connected sink. Rebooting with the PHY in the connected state also
results in a system hang.
Fix the above by disconnecting TypeC PHYs on disabled ports.
Before commit 64851a32c4 the PHY connected state was read out even
for disabled ports and later the PHY got disconnected as a side effect
of a tc_port_lock/unlock() sequence (during connector probing), hence
recovering the port's hotplug functionality.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5014
Fixes: 64851a32c4 ("drm/i915/tc: Add a mode for the TypeC PHY's disconnected state")
Cc: <stable@vger.kernel.org> # v5.16+
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220217152237.670220-1-imre.deak@intel.com
Several of our i915 header files, have been including i915_reg.h. This
means that any change to i915_reg.h will trigger a full rebuild of
pretty much every file of the driver, even those that don't have any
kind of register access. Let's delete the i915_reg.h include from all
headers and add an explicit include from the .c files that truly
need the register definitions; those that need a definition of
i915_reg_t for a function definition can get it from i915_reg_defs.h
instead.
We also remove two non-register #define's (VLV_DISPLAY_BASE and
GEN12_SFC_DONE_MAX) into i915_reg_defs.h to allow us to drop the
i915_reg.h include from a couple of headers.
There's probably a lot more header dependency optimization possible, but
the changes here roughly cut the number of files compiled after 'touch
i915_reg.h' in half --- a good first step.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127234334.4016964-7-matthew.d.roper@intel.com
The TCSS_DDI_STATUS register is indexed by tc_port not by the FIA port
index, fix this up. This only caused an issue on TC#3/4 ports in legacy
mode, as in all other cases the two indices either match (on TC#1/2) or
the TCSS_DDI_STATUS_READY flag is set regardless of something being
connected or not (on TC#1/2/3/4 in dp-alt and tbt-alt modes).
Reported-and-tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Fixes: 55ce306c2a ("drm/i915/adl_p: Implement TC sequences")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4698
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: <stable@vger.kernel.org> # v5.14+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220126104356.2022975-1-imre.deak@intel.com
Registers representing the MG/DKL TC PHYs (including the TC DPLLs which
exist inside the PHY) are only needed in a couple files and on specific
platforms; let's keep them separate from the general register pool.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220111051600.3429104-11-matthew.d.roper@intel.com
The PHY ownership release->AUX PW disable steps during a modeset
disable->PHY disconnect sequence can hang the system if the PHY
disconnect happens after disabling the PHY's PLL. The spec doesn't
require a specific order for these two steps, so this issue is still
being root caused by HW/FW teams. Until that is found, let's make
sure the disconnect happens before the PLL is disabled, and do this on
all platforms for consistency.
v2: Add a TODO comment to remove the w/a once the issue is root
caused/fixed. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-7-imre.deak@intel.com
After the previous patch the driver holds a power domain blocking
TC-cold whenever the port is locked, so we can remove the extra blocking
around the lock/unlock sequence.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-13-imre.deak@intel.com
So far TC-cold was blocked only for the duration of TypeC mode resets.
The DP-alt and legacy modes require TC-cold to be blocked also whenever
the port is in use (AUX transfers, enable modeset), and this was ensured
by the held PHY ownership flag. On ADL-P this doesn't work, since the
PHY ownership flag is in a register backed by the PW#2 power well.
Whenever this power well is disabled the ownership flag is cleared by
the HW under the driver.
The only way to cleanly release and re-acquire the PHY ownership flag
and also allow for power saving (by disabling the display power wells
and reaching DC5/6 states) is to hold the TC-cold blocking power domains
while the PHY is connected and disconnect/reconnect the PHY on-demand
around AUX transfers and modeset enable/disables. Let's do that,
disconnecting a PHY with a 1 sec delay after it becomes idle. For
consistency do this on all platforms and TypeC modes.
v2: Add tc_mode!=disconnected and phy_is_owned asserts to
__intel_tc_port_lock().
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-6-imre.deak@intel.com
While a TypeC port mode is locked a DISPLAY_CORE power domain reference
is held, which implies a runtime PM ref. By removing the ICL !legacy
port special casing, a TC_COLD_OFF power domain reference will be taken
for such ports, which also translates to a runtime PM ref on that
platform. A follow-up change will stop holding the DISPLAY_CORE power
domain while the port is locked.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-11-imre.deak@intel.com
For the ADL-P TBT mode the spec doesn't require blocking TC-cold by
using the legacy AUX power domain. To avoid the timeouts that this would
cause during PHY disconnect/reconnect sequences (which will be more
frequent after a follow-up change) use the TC_COLD_OFF power domain in
TBT mode on all platforms. On TGL this power domain blocks TC-cold via a
PUNIT command, while on other platforms the domain just takes a runtime
PM reference.
If the HPD live status indicates that the port mode needs to be reset
- for instance after switching from TBT to a DP-alt sink - still take
the AUX domain, since the IOM firmware handshake requires this.
v2: Rebased on v2 of the previous patch.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-5-imre.deak@intel.com
A follow-up change will select the TC-cold blocking power domain based
on the TypeC mode, prepare for that here.
Also bring intel_tc_cold_requires_aux_pw() earlier to its logical place
for readability.
No functional change.
v2: Add code comment about IOM reg accesses in TCCOLD. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-4-imre.deak@intel.com
A follow-up change will start to disconnect/re-connect PHYs around AUX
transfers and modeset enable/disables. To prepare for that add a new
TypeC PHY disconnected mode, to help tracking the TC-cold blocking power
domain status (no power domain in disconnected state, mode dependent
power domain in connected state).
v2: Move the !disconnected mode and phy-owned asserts in
__intel_tc_port_lock() later in the patchset, when the asserts will
hold. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-3-imre.deak@intel.com
A follow-up patch will disconnect/reconnect PHYs around AUX transfers
and modeset enable/disables. To prepare for that and make things
consistent for all TypeC modes stop connecting the PHY in legacy mode
without a sink being connected. This was done before since in legacy
mode the PHY is dedicated to display usage, so there was no point in
disconnecting it. However after the follow-up changes the TC-cold
blocking power domains will be held as long as the PHY is in the
connected state, so we'll need to disconnect/re-connect the PHY in all
TypeC modes to allow for power saving.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-7-imre.deak@intel.com
Instead of directly accessing the TypeC port internal struct members,
add/use helpers to retrieve the corresponding properties.
No functional change.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-6-imre.deak@intel.com
On ADL-P the PHY ready/complete flag is always set even in TBT-alt mode.
To avoid taking the PHY ownership and the following spurious "PHY sudden
disconnect" messages on this platform when connecting the PHY in TBT
mode, check if there is any DP-alt or legacy sink connected before
taking the ownership.
v2: (Jose)
- Fix debug message clarifying that a TBT sink can be connected.
- Add comments describing the PHY complete HW flag semantic differences
between adl-p and other platforms.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-2-imre.deak@intel.com
Waiting for the PHY complete flag to clear when releasing the PHY
ownership was add in
commit ddec362724 ("drm/i915: Wait for TypeC PHY complete flag to clear in safe mode")
This isn't required by the spec, the vague idea was to make the
handshake with the firmware more robust, without actual evidence for
when it would be needed. Checking this again, the flag doesn't clear on
ICL until after the PHY's PLL is disabled and the flag is permanently
set on ADL-P. To avoid the spurious timeout messages in dmesg, just
remove this wait.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-4-imre.deak@intel.com
On ADL-P the PHY ready (aka status complete on other platforms) flag is
always set, besides when a DP-alt, legacy sink is connected also when a
TBT sink is connected or nothing is connected. So assume the PHY to be
connected when both the TBT live status and PHY ready flags are set.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-3-imre.deak@intel.com
Disconnect TypeC PHYs during system suspend and shutdown, even with the
corresponding TypeC sink still plugged to its connector, since leaving
the PHY connected causes havoc at least during system resume in the
presence of an Nvidia card.
Note that this will only make a difference in the TypeC DP alternate
mode, since in Thunderbolt alternate mode the PHY is never owned by the
display engine and there is no notion of PHY ownership in legacy mode
(the display engine being the only possible owner in that mode and the
TypeC subsystem not having anything to do with the port in that case).
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3500
Reported-and-tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210610174223.605904-1-imre.deak@intel.com
On ADL-P TC cold is exited and blocked when legacy aux is powered,
that is exacly the same of what ICL need for static TC ports.
TODO: When a TBT hub or monitor is connected it will cause TBT and
legacy aux to be powered at the same time, hopefully this will not
cause any issues but if it do, some rework will be needed.
v2:
- skip icl_tc_port_assert_ref_held() warn on, adl-p uses aux to
block TC cold
v3:
- Drop icl_tc_port_assert_ref_held() earlier return for adl_p, not
needed anymore
- Set timeout_expected when enabling aux power well as port could be
disconnected when tc_cold_block() is called
BSpec: 55480
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210524214805.259692-2-jose.souza@intel.com
MODULAR_FIA_MASK is set in adl_p so we can drop this ealier return
and read registers.
Also to avoid warnings from icl_tc_port_assert_ref_held() when
calling tc_cold_block() in this functions it is necessary to held the
lock.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210524214805.259692-1-jose.souza@intel.com
ADL-P have basically the same TC connection and disconnection
sequences as ICL and TGL, the major difference is the new registers.
So here adding functions without the icl prefix in the name and
making the new functions call the platform specific function to access
the correct register.
v2:
- Retain DDI TC PHY ownership flag during modesetting.
BSpec: 55480
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-6-lucas.demarchi@intel.com
Alderlake P have modular FIA like TGL but it is always modular in all
skus, not like TGL that we had to read a register to check if it is
monolithic or modular.
BSpec: 55480
BSpec: 50572
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-11-matthew.d.roper@intel.com
When DP_PHY_MODE_STATUS_NOT_SAFE is set, it means that display
has the control over the TC phy.
The "not safe" naming is confusing using ownership make it easier
to read also future platforms will have a new register that does the
same job as DP_PHY_MODE_STATUS_NOT_SAFE but with the onwership name.
BSpec: 49294
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-10-matthew.d.roper@intel.com
While converting the rest of the driver to use GRAPHICS_VER() and
MEDIA_VER(), following what was done for display, some discussions went
back on what we did for display:
1) Why is the == comparison special that deserves a separate
macro instead of just getting the version and comparing directly
like is done for >, >=, <=?
2) IS_DISPLAY_RANGE() is weird in that it omits the "_VER" for
brevity. If we remove the current users of IS_DISPLAY_VER(), we
could actually repurpose it for a range check
With (1) there could be an advantage if we used gen_mask since multiple
conditionals be combined by the compiler in a single and instruction and
check the result. However a) INTEL_GEN() doesn't use the mask since it
would make the code bigger everywhere else and b) in the cases it made
sense, it also made sense to convert to the _RANGE() variant.
So here we repurpose IS_DISPLAY_VER() to work with a [ from, to ] range
like was the IS_DISPLAY_RANGE() and convert the current IS_DISPLAY_VER()
users to use == and != operators. Aside from the definition changes,
this was done by the following semantic patch:
@@ expression dev_priv, E1; @@
- !IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) != E1
@@ expression dev_priv, E1; @@
- IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) == E1
@@ expression dev_priv, from, until; @@
- IS_DISPLAY_RANGE(dev_priv, from, until)
+ IS_DISPLAY_VER(dev_priv, from, until)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Jani: Minor conflict resolve while applying.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210413051002.92589-4-lucas.demarchi@intel.com
Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:
@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)
@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)
@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)
@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)
There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.
v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com
The TypeC FIA can be powered down if the TC-COLD power state is allowed,
so block the TC-COLD state when initializing the FIA.
Note that this isn't needed on ICL where the FIA is never modular and
which has no generic way to block TC-COLD (except for platforms with a
legacy TypeC port and on those too only via these legacy ports, not via
a DP-alt/TBT port).
Cc: <stable@vger.kernel.org> # v5.10+
Cc: José Roberto de Souza <jose.souza@intel.com>
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3027
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210208154303.6839-1-imre.deak@intel.com
Reviewed-by: Jos� Roberto de Souza <jose.souza@intel.com>
If the VBT assigned tc->legacy_port mismatches the live_status indicator
for the connector, we ignore the VBT directive and switch over to the HW
setting. This is not a driver error, unless we happen to misparse the
VBT or the live_status registers. However, for the system in CI where
the error is only reported on 1 port out of 4, the evidence indicates
the VBT is wrong. Stop flaging this as an error since the cause is
beyond our control, fixup the mistake and continue on.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201030153209.14808-1-chris@chris-wilson.co.uk
struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.
Prefer drm_WARN_ON over WARN_ON.
Conversion is done with below sementic patch:
@@
identifier func, T;
@@
func(...) {
...
struct drm_i915_private *T = ...;
<+...
-WARN_ON(
+drm_WARN_ON(&T->drm,
...)
...+>
}
@@
identifier func, T;
@@
func(struct intel_digital_port *T,...) {
+struct drm_i915_private *i915 = to_i915(T->base.base.dev);
<+...
-WARN_ON(
+drm_WARN_ON(&i915->drm,
...)
...+>
}
changes since v1:
- Add i915 local variable and use it in drm_WARN_ON (Jani)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504181600.18503-5-pankaj.laxminarayan.bharadiya@intel.com
Get rid of several platform specific variants of
intel_digital_port_connected() and just use the ISR bits we've
stashed away.
v2: Duplicate stuff to avoid exposing platform specific
functions across files (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Let's get rid of the platform if ladders in
intel_digital_port_connected() and make it a vfunc. Now the if
ladders are at the encoder initialization which makes them a bit
less convoluted.
v2: Add forward decl for intel_encoder in intel_tc.h
v3: Duplicate stuff to avoid exposing platform specific
functions across files (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
As described in "drm/i915/tc/icl: Implement TC cold sequences" users
of TC functions should held aux power well during access to avoid
read garbage due HW in TC cold state.
v3:
- renamed is_tc_cold_blocked() to assert_tc_cold_blocked()
- restored the removed 0xffffffff checks
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-7-jose.souza@intel.com
TC ports can enter in TCCOLD to save power and is required to request
to PCODE to exit this state before use or read to TC registers.
For TGL there is a new MBOX command to do that with a parameter to ask
PCODE to exit and block TCCOLD entry or unblock TCCOLD entry.
So adding a new power domain to reuse the refcount and only allow
TC cold when all TC ports are not in use.
v2:
- fixed missing case in intel_display_power_domain_str()
- moved tgl_tc_cold_request to intel_display_power.c
- renamed TGL_TC_COLD_OFF to TGL_TC_COLD_OFF_POWER_DOMAINS
- added all TC and TBT aux power domains to
TGL_TC_COLD_OFF_POWER_DOMAINS
v3:
- added one msec sleep when PCODE returns -EAGAIN
- added timeout of 5msec to not loop forever if
sandybridge_pcode_write_timeout() keeps returning -EAGAIN
v4:
- Made failure to block or unblock TC cold a error
- removed 5msec timeout, instead giving PCODE 1msec by up 3 times to
recover from the internal error
v5:
- only sleeping 1msec when ret is -EAGAIN
BSpec: 49294
Cc: Imre Deak <imre.deak@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-6-jose.souza@intel.com
This is required for legacy/static TC ports as IOM is not aware of
the connection and will not trigger the TC cold exit.
Just request PCODE to exit TCCOLD is not enough as it could enter
again before driver makes use of the port, to prevent it BSpec states
that aux powerwell should be held.
So here embedding the TC cold exit sequence into ICL aux enable,
it will enable aux and then request TC cold to exit.
The TC cold block(exit and aux hold) and unblock was added to some
exported TC functions for the others and to access PHY registers,
callers should enable and keep aux powerwell enabled during access.
Also adding TC cold check and warnig in tc_port_load_fia_params() as
at this point of the driver initialization we can't request power
wells, if we get this warning we will need to figure out how to handle
it.
v2:
- moved ICL TC cold exit function to intel_display_power
- using dig_port->tc_legacy_port to only execute sequences for legacy
ports, hopefully VBTs will have this right
- fixed check to call _hsw_power_well_continue_enable()
- calling _hsw_power_well_continue_enable() unconditionally in
icl_tc_phy_aux_power_well_enable(), if needed we will surpress timeout
warnings of TC legacy ports
- only blocking TC cold around fia access
v3:
- added timeout of 5msec to not loop forever if
sandybridge_pcode_write_timeout() keeps returning -EAGAIN
returning -EAGAIN in in icl_tc_cold_exit()
- removed leftover tc_cold_wakeref
- added one msec sleep when PCODE returns -EAGAIN
v4:
- removed 5msec timeout, instead giving 1msec to whoever is using
PCODE to finish it up to 3 times
- added a comment about turn TC cold exit failure as a error in future
BSpec: 21750
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1296
Cc: Imre Deak <imre.deak@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-4-jose.souza@intel.com
