Add new member to struct intel_dp to cache support of Adaptive Sync
SDP capabilities and use it whenever required to avoid HW access
to read capability during each atomic commit.
-v2:
- Squash both the patches
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240704082638.2302092-2-mitulkumar.ajitkumar.golani@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Lets unify both bigjoiner and ultrajoiner under simple "joiner" name,
because in future we might have multiple configurations, involving
multiple bigjoiners, ultrajoiner, however it is possible to use
same api for handling both.
v2: - Renamed back some bigjoiner specific parts for now(Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
[vsyrjala: Catch a few more cases]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607075457.15700-1-stanislav.lisovskiy@intel.com
Compute Fixed Average Vtotal/CMRR with resepect to
userspace VRR enablement. Also calculate required
parameters in case of CMRR is enabled. During
intel_vrr_compute_config, CMRR is getting enabled
based on userspace has enabled Variable refresh mode
with VRR timing generator or not. Make CMRR as small subset of
FAVT mode, when Panel is running on Fixed refresh rate
and on VRR framework then only enable CMRR to match with
actual refresh rate.
--v2:
- Update is_cmrr_frac_required function return as bool, not int. [Jani]
- Use signed int math instead of unsigned in cmrr_get_vtotal2. [Jani]
- Fix typo and usage of camel case in cmrr_get_vtotal. [Jani]
- Use do_div in cmrr_get_vtotalwhile calculating cmrr_m. [ Jani]
- Simplify cmrr and vrr compute config in intel_vrr_compute_config. [Jani]
- Correct valiable name usage in is_cmrr_frac_required. [Ville]
--v3:
- Removing RFC tag.
--v4:
- Added edp check to address edp usecase for now. (ville)
- Updated is_cmrr_fraction_required to more simplified calculation.
- on longterm goal to be worked upon uapi as suggestion from ville.
--v5:
- Correct vtotal paramas accuracy and add 2 digit precision.
- Avoid using DIV_ROUND_UP and improve scanline precision.
--v6:
- Make CMRR a small subset of FAVT mode.
--v7:
- Update commit message to avoid confusion with Legacy VRR (Ankit).
- Add cmrr.enable in last, so remove from this patch.
--v8:
- Set cmrr.enable in current patch instead of separate patch (Ankit).
- Since vrr.enable and cmrr.enable are not mutually exclusive,
handle accordingly (Ankit).
- is_edp is not required inside is_cmrr_frac_required function (Ankit).
- Add video_mode_required flag for future enhancement.
- Correct cmrr_m/cmrr_n calculation.
--v9:
- Move patch to last and set other bits before computing
cmrr.enable.(Ankit)
- Add TODO: for to address target refresh rate precision as future
enhancement.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610072203.24956-10-mitulkumar.ajitkumar.golani@intel.com
Compute vrr vsync params in case of FAVT as well instead of
only to AVT mode of operation.
--v2:
- Remove redundant computation for vrr_vsync_start
and vrr_vsync_end(Ankit).
--v3:
- vrr.enable and cmrr.enable check together is not required as both
will be true at the same point in time. (Ankit)
- Replace vrr.enable flag to cmrr.enable, mistakenly added. (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610072203.24956-9-mitulkumar.ajitkumar.golani@intel.com
Add/update trans_vrr_ctl flag when crtc_state->cmrr.enable
is set, With this commit setting the stage for subsequent
CMRR enablement.
--v2:
- Check pipe active state in cmrr enabling. [Jani]
- Remove usage of bitwise OR on booleans. [Jani]
- Revert unrelated changes. [Jani]
- Update intel_vrr_enable, vrr and cmrr enable conditions. [Jani]
- Simplify whole if-ladder in intel_vrr_enable. [Jani]
- Revert patch restructuring mistakes in intel_vrr_get_config. [Jani]
--v3:
- Check pipe active state in cmrr disabling.[Jani]
- Correct messed up condition in intel_vrr_enable. [Jani]
--v4:
- Removing RFC tag.
--v5:
- CMRR handling in co-existatnce of LRR and DRRS.
--v7:
- Rebase on top of AS SDP merge.
--v8:
- Remove cmrr_enabling/disabling and update commit message. (Ankit)
--v9:
- Revert removed line(Ankit).
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610072203.24956-5-mitulkumar.ajitkumar.golani@intel.com
Add register definitions for Transcoder Fixed Average
Vtotal mode/CMRR function, with the necessary bitfields.
Compute these registers when CMRR is enabled, extending
Adaptive refresh rate capabilities.
--v2:
- Use intel_de_read64_2x32 in intel_vrr_get_config. [Jani]
- Fix indent and order based on register offset. [Jani]
--v3:
- Removing RFC tag.
--v4:
- Update place holder for CMRR register definition. (Jani)
--v5:
- Add CMRR register definitions to a separate file intel_vrr_reg.h.
--v6:
- Fixed indentation. (Jani)
- Add dependency header intel_display_reg_defs.h. (Jani)
- Rename file name to intel_vrr_regs.h instead of reg.h (Jani)
--v7:
- Remove adding CMRR flag to vrr_ctl register during set_transcoder_timing,
as it is already being done during intel_vrr_enable. (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610072203.24956-4-mitulkumar.ajitkumar.golani@intel.com
All joined pipes share the same transcoder/timing generator.
Currently we just do the commits per-pipe, which doesn't really
work if we need to change switch between non-VRR and VRR timings
generators on the fly, or even when sending the push to the
transcoder. For now just disable VRR when bigjoiner is needed.
Cc: stable@vger.kernel.org
Tested-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404213441.17637-6-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Compute vrr_vsync_start/end, which sets the position
for hardware to send the Vsync at a fixed position
relative to the end of the Vblank.
--v2:
- Updated VSYNC_START/END macros to VRR_VSYNC_START/END. (Ankit)
- Updated bit fields of VRR_VSYNC_START/END. (Ankit)
--v3:
- Add PIPE_CONF_CHECK_I(vrr.vsync_start/end).
- Read/write vrr_vsync params only when we intend to send
adaptive_sync sdp.
--v4:
- Use VRR_SYNC_START/END macros correctly.
--v5:
- Send AS SDP only when VRR is enabled.
--v6:
- Add TRANS_VRR_VSYNC before enabling VRR as per bspec. (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-9-mitulkumar.ajitkumar.golani@intel.com
Looks like TRANS_CHICKEN bit 31 means something totally different
depending on the platform:
TGL: generate VRR "safe window" for DSB
ADL/DG2: make TRANS_SET_CONTEXT_LATENCY effective with VRR
So far we've only set this on ADL/DG2, but when using DSB+VRR
we also need to set it on TGL.
And a quick test on MTL says it doesn't need this bit for either
of those purposes, even though it's still documented as valid
in bspec.
Cc: stable@vger.kernel.org
Fixes: 34d8311f4a ("drm/i915/dsb: Re-instate DSB for LUT updates")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9927
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240306040806.21697-2-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Implement low refresh rate (LRR) where we change the vblank
length by hand as requested, but otherwise keep the timing
generator running in non-VRR mode (ie. fixed refresh rate).
The panel itself must support VRR for this to work, and
only TGL+ has the double buffred TRANS_VTOTAL.VTOTAL that
we need to make the switch properly. The double buffer
latching happens at the start of transcoders undelayed
vblank. The other thing that we change is
TRANS_VBLANK.VBLANK_END but the hardware entirely ignores
that in DP mode. But I decided to keep writing it anyway
just to avoid more special cases in readout/state check.
v2: Document that TRANS_VBLANK.VBLANK_END is ignored by
the hardware
v3: Reconcile with VRR fastset
Adjust update_lrr flag behaviour
Make sure timings stay within VRR range
v4: Fix up update_m_n vs. update_lrr rebase fail (Manasi)
Drop DOUBLE_BUFFER_VACTIVE define as it's not needed (Manasi)
TODO: Hook LRR into the automatic DRRS downclocking stuff?
Cc: Manasi Navare <navaremanasi@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230915103800.14218-1-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <navaremanasi@chromium.org>
Let's assume there are some crazy displays where the high
end of the VRR range ends up being lower than the refresh
rate as determined by the actual timings. In that case
when we toggle VRR on/off we would step outside the VRR
range when toggling VRR on/off. Let's just make sure that
never happens by not using VRR in such cases. If the user
really wants VRR they should then select the timings to
land within the VRR range.
Cc: Manasi Navare <navaremanasi@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901130440.2085-9-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <navaremanasi@chromium.org>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Move is_in_vrr_range() into intel_vrr.c in anticipation of
more users, and rename it accordingly.
Cc: Manasi Navare <navaremanasi@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901130440.2085-8-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <navaremanasi@chromium.org>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Move VRR enabling/disabling into a place where it also works
for fastsets.
With this we always start the transcoder up in non-VRR mode.
Granted we already did that but for a very short period of
time. But now that we might end up doing a bit more with the
transcoder in non-VRR mode it seems prudent to also update
the active timings as the transcoder changes its operating
mode.
crtc_state->vrr.enable still tracks whether VRR is actually
enabled or not, but now we configure all the other VRR timing
registers whenever VRR is possible (whether we actually enable
it or not). crtc_state->vrr.flipline can now serve as our
"is VRR possible" bit of state.
I decided to leave the MSA timing ignore bit set all the time
whether VRR is actually enabled or not. If the sink can figure
out the timings with that information when VRR is active then
surely it can also do it when VRR is inactive.
v2: Protect intel_vrr_set_transcoder_timings() with HAS_VRR()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321135615.27338-1-ville.syrjala@linux.intel.com
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
On adl/dg2 a chicken bit needs to be set for TRANS_SET_CONTENXT_LATENCY
to take effect in VRR mode. Can't really think of a reason why we'd
ever disable that chicken bit, so let's just always set it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320203352.19515-4-ville.syrjala@linux.intel.com
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
The "window2" delay is just the difference of vactive
(undelayed vblank) vs. vblank_start (delayed vblank).
Just use vblank_start during the VRR calculations so
that things work correctly regardless of whether delayed
vblank is used or not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127173044.24108-2-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
On mtl (at least) clearing the guardband bits in the same write
as the enable bit gets cleared seems to cause an immediate FIFO
underrun. Thus is seems that we need to first clear just the
enable bit, then wait for the VRR live status to indicate the
transcoder has exited VRR mode (this step is documented in Bspec
as well), and finally we can clear out the rest of the TRANS_VRR_CTL
for good measure.
I did this without any RMWs in case we want to toggle VRR on/off
via DSB in the future, and as we know DSB can't read registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221202134412.21943-5-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
We are miscalculating both the guardband value, and the resulting
vblank exit length on adl+. This means that our start of vblank
(double buffered register latch point) is incorrect, and we also
think that it's not where it actually is (hence vblank evasion/etc.
may not work properly). Fix up the calculations to match the real
hardware behaviour (as reverse engineered by intel_display_poller).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221202134412.21943-3-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Account for the framestart delay when calculating the "pipeline full"
value for icl/tgl vrr. This puts the start of vblank (ie. where the
double bufferd registers get latched) to a consistent place regardless
of what framestart delay value is used. framestart delay does not
change where start of vblank occurs in non-vrr mode and I can't see
any reason why we'd want different behaviour in vrr mode.
Currently framestart delay is always set to 1, and the hardcoded 4
scanlines in the code means we're currently delaying the start of
vblank by three extra lines. And with framestart delay set to 4 we'd
have no extra delay.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221202134412.21943-2-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
We need to make framestart_delay dynamic for DRRS on PCH
ports. To that end move it into the crtc state. As a bonus
we get state check+dump for it. Will also allow us to get
rid of the somewhat questionable framestart_delay sanitation
code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221110356.5532-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Since I originally wrote these comments we decided to change our
definition of framestart_delay from 0-3 to 1-4. Adjust the comments
to match that new convention. The actual code was adjusted already.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117183103.27418-3-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Let's adjust the vblank evasion to account for the case where
a push has already been sent. In that case the vblank exit will start
at vmin vblank start (as opposed to vmax vblank start when no push
has been sent).
This should minimize the effects of the tiny race between sampling
the frame counter vs. intel_vrr_send_push() during the previous frame.
This will also be required if we want to do mailbox style updates with
vrr since then we'd definitely do multiple commits per frame. Currently
mailbox updates are only used by the legacy cursor, but we don't do
vrr push for those.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117183103.27418-2-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
On XE_LPD, VRR CTL register adds a new VRR Guardband bitfield
replacing the pipeline full and deprecating the pipeline override
bit.
This patch adds this corresponding bitfield in the register defs,
crtc state vrr structure and populates this in vrr compute
config and vrr enable functions. It also adds the corresponding
HW state readout for this field.
Bspec: 50508
Cc: Aditya Swarup <aditya.swarup@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Aditya Swarup <aditya.swarup@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210526000656.3060314-3-matthew.d.roper@intel.com
Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.
This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)
@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)
@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"
@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
To get sensible vblank timestamping behaviour we need to feed
the vmax based timings to the vblank code, otherwise it'll chop
off the scanline counter when it exceeds the minumum vtotal.
Additionally with VRR we have three cases to consider when we
generate the vblank timestamp:
1) we are in vertical active
-> nothing special needs to be done, just return the current
scanout position and the core will calculate the timestamp
corresponding to the past time when the current vertical
active started
2) we are in vertical blank and no push has been sent
-> the hardware will keep extending the vblank presumably
to its maximum length, so we make the timestmap match the
expected time when the max length vblank will end. Since
the timings used for this are now based on vmax nothing
special actually needs to be done
3) we are in vblank and a push has been sent so the vblank is
about to terminate
-> presumably we want the timestmap to accurately reflect
when the vblank will terminate, so we use the sampled
frame timestamp vs. current timestamp to guesstimate
how far along the vblank exit we are, and then we
adjust the reported scanout position accordingly so
that the core will see that the vblank is close to
ending.
v2:
* Fix the else if (use_scanline_Counter) (Manasi)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-17-manasi.d.navare@intel.com
With VRR the earliest the registers can get latched are at
flipline decision boundary, calculate that as vrr_vmin_vblank_start()
and the latest the regsiters can get latched are vmax decision boundary
calculate that as vrr_vmax_vblank_start()
v2:
* Remove TODO and adjust extra scanline const (Manasi)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-15-manasi.d.navare@intel.com
This functions gets the VRR config from the VRR registers
to match the crtc state variables for VRR.
v2:
* Rebase (Manasi)
* Use HAS_VRR (Jani N)
v3:
* Get pipeline_full, flipline (Ville)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-14-manasi.d.navare@intel.com
This patch disables the VRR enable and VRR PUSH
bits in the HW during commit modeset disable sequence.
Thsi disable will happen when the port is disabled
or when the userspace sets VRR prop to false and
requests to disable VRR.
v2:
* Use intel_de_rmw (Jani N)
v3:
* Remove rmw (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-12-manasi.d.navare@intel.com
VRR achieves vblank stretching using the HW PUSH functionality.
So once the VRR is enabled during modeset then for each flip
request from userspace, in the atomic tail pipe_update_end()
we need to set the VRR push bit in HW for it to terminate
the vblank at configured flipline or anytime after flipline
or latest at the Vmax.
The HW clears the PUSH bit after the double buffer updates
are completed.
v2:
* Move send push to after irq en (Manasi)
* Call send push unconditionally (Jani N)
v3:
* Stall w.r.t Vrr vmax (Manasi, Gary Smith)
v4:
* Remove the rmw (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gary Smith <gary.k.smith@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-11-manasi.d.navare@intel.com
This patch computes the VRR parameters from VRR crtc states
and configures them in VRR registers during CRTC enable in
the modeset enable sequence.
v2:
* Remove initialization to 0 (Jani N)
* Use correct pipe %c (Jani N)
v3:
* Remove debug prints (Ville)
* Use cpu_trans instead of pipe for TRANS_VRR regs (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-10-manasi.d.navare@intel.com
This forces a complete modeset if vrr drm crtc state goes
from enabled to disabled and vice versa.
This patch also computes vrr state variables from the mode timings
and based on the vrr property set by userspace as well as hardware's
vrr capability.
v2:
*Rebase
v3:
* Vmin = max (vtotal, vmin) (Manasi)
v4:
* set crtc_state->vrr.enable = 0 for disable request
v5:
* drm_dbg_kms, squash crtc states def patch (Jani N)
v6:
* Move vrr modeset check to separate function (Jani N)
v7:
* Ville's fixes - vmin, vmax rename, fix rounding dir
* Add pipeline full, flipline to crtc state
* Pass conn state to vrr_compute_config (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-6-manasi.d.navare@intel.com
This function sets the VRR property for connector based
on the platform support, EDID monitor range and DP sink
DPCD capability of outputing video without msa
timing information.
v8:
* Use HAS_VRR, remove drm_conn declaration (Jani N)
* Fix typos in Comment (Jani N)
v7:
* Move the helper to separate file (Manasi)
v6:
* Remove unset of prop
v5:
* Fix the vrr prop not being set in kernel (Manasi)
* Unset the prop on connector disconnect (Manasi)
v4:
* Rebase (Mansi)
v3:
* intel_dp_is_vrr_capable can be used for debugfs, make it
non static (Manasi)
v2:
* Just set this in intel_dp_get_modes instead of new hook (Jani)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-2-manasi.d.navare@intel.com
We create a new file for all VRR related helpers.
Also add a function to check vrr capability based on
platform support, DPCD bits and EDID monitor range.
v2:
* Remove author (Jani N)
* Define HAS_VRR (Jani N)
* Ensure intel_dp can be obtained from conn (Jani N)
v3:
* Fix the header indent (Manasi)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210125200818.2015-1-manasi.d.navare@intel.com
