MT7531_CPU_PMAP represents the destination port mask for trapped-to-CPU
frames (further restricted by PCR_MATRIX).
Currently the driver sets the first CPU port as the single port in this bit
mask, which works fine regardless of whether the device tree defines port
5, 6 or 5+6 as CPU ports. This is because the logic coincides with DSA's
logic of picking the first CPU port as the CPU port that all user ports are
affine to, by default.
An upcoming change would like to influence DSA's selection of the default
CPU port to no longer be the first one, and in that case, this logic needs
adaptation.
Since there is no observed leakage or duplication of frames if all CPU
ports are defined in this bit mask, simply include them all.
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DEV_MAC_MAXLEN_CFG register contains a 16-bit value - up to 65535.
Plus 2 * VLAN_HLEN (4), that is up to 65543.
The picos_per_byte variable is the largest when "speed" is lowest -
SPEED_10 = 10. In that case it is (1000000L * 8) / 10 = 800000.
Their product - 52434400000 - exceeds 32 bits, which is a problem,
because apparently, a multiplication between two 32-bit factors is
evaluated as 32-bit before being assigned to a 64-bit variable.
In fact it's a problem for any MTU value larger than 5368.
Cast one of the factors of the multiplication to u64 to force the
multiplication to take place on 64 bits.
Issue found by Coverity.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230613170907.2413559-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/sch_taprio.c
d636fc5dd6 ("net: sched: add rcu annotations around qdisc->qdisc_sleeping")
dced11ef84 ("net/sched: taprio: don't overwrite "sch" variable in taprio_dump_class_stats()")
net/ipv4/sysctl_net_ipv4.c
e209fee411 ("net/ipv4: ping_group_range: allow GID from 2147483648 to 4294967294")
ccce324dab ("tcp: make the first N SYN RTO backoffs linear")
https://lore.kernel.org/all/20230605100816.08d41a7b@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pointer variables of (void*) type do not require type cast.
Signed-off-by: Atin Bainada <hi@atinb.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
This error path needs call mutex_unlock(&ocelot->tas_lock) before
returning.
Fixes: 2d800bc500 ("net/sched: taprio: replace tc_taprio_qopt_offload :: enable with a "cmd" enum")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 PHY errata handling code has now been moved into the Micrel
PHY driver, so it is no longer needed inside the DSA switch driver.
Remove it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new xpcs_create_mdiodev() creator, which simplifies the
creation and destruction of the mdio device associated with xpcs.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the mdiodev after xpcs_create() so that the XPCS driver can manage
the lifetime of the mdiodev its using.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without LED triggers, the driver now fails to build:
drivers/net/dsa/qca/qca8k-leds.c: In function 'qca8k_parse_port_leds':
drivers/net/dsa/qca/qca8k-leds.c:403:31: error: 'struct led_classdev' has no member named 'hw_control_is_supported'
403 | port_led->cdev.hw_control_is_supported = qca8k_cled_hw_control_is_supported;
| ^
There is a mix of 'depends on' and 'select' for LEDS_TRIGGERS, so it's
not clear what we should use here, but in general using 'depends on'
causes fewer problems, so use that.
Fixes: e0256648c8 ("net: dsa: qca8k: implement hw_control ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN9303 doesn't associate FDB (ALR) entries with VLANs, it has just one
global Address Logic Resolution table [1].
Ignore VID in port_fdb_{add|del} methods, go on with the global table. This
is the same semantics as hellcreek or RZ/N1 implement.
Visible symptoms:
LAN9303_MDIO 5b050000.ethernet-1:00: port 2 failed to delete 00:xx:xx:xx:xx:cf vid 1 from fdb: -2
LAN9303_MDIO 5b050000.ethernet-1:00: port 2 failed to add 00:xx:xx:xx:xx:cf vid 1 to fdb: -95
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/00002308A.pdf
Fixes: 0620427ea0 ("net: dsa: lan9303: Add fdb/mdb manipulation")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230531143826.477267-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de4 ("net: dsa: mv88e6xxx: wait after reset deactivation")
Signed-off-by: Andreas Svensson <andreas.svensson@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Inspired from struct flow_cls_offload :: cmd, in order for taprio to be
able to report statistics (which is future work), it seems that we need
to drill one step further with the ndo_setup_tc(TC_SETUP_QDISC_TAPRIO)
multiplexing, and pass the command as part of the common portion of the
muxed structure.
Since we already have an "enable" variable in tc_taprio_qopt_offload,
refactor all drivers to check for "cmd" instead of "enable", and reject
every other command except "replace" and "destroy" - to be future proof.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> # for lan966x
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mv88e6250 family switch with 5 internal PHYs, 2 RMIIs
and no PTP support.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mv88e6250 family switch with 2 PHY and RMII ports and
no PTP support.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches from mv88e6250 family (including mv88e6020 and mv88e6071) need
the possibility to setup the maximal frame size, as they support frames
up to 2048 bytes.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order that the LED trigger can blink the switch MAC ports LED, it
needs to know the netdev associated to the port. Add the callback to
return the struct device of the netdev.
Add an helper function qca8k_phy_to_port() to convert the phy back to
dsa_port index, as we reference LED port based on the internal PHY
index and needs to be converted back.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement hw_control ops to drive Switch LEDs based on hardware events.
Netdev trigger is the declared supported trigger for hw control
operation and supports the following mode:
- tx
- rx
When hw_control_set is called, LEDs are set to follow the requested
mode.
Each LEDs will blink at 4Hz by default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E6361 is an 8-port switch derived from the
88E6393X/88E9193X/88E6191X switches family. It can benefit from the
existing mv88e6xxx driver by simply adding the proper switch description in
the driver. Main differences with other switches from this
family are:
- 8 ports exposed (instead of 11): ports 1, 2 and 8 not available
- No 5GBase-x nor SFI/USXGMII support
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some switches families have minor differences on supported link speed for
ports. Instead of redefining a new port_max_speed_mode for each different
configuration, allow to pass mv88e6xxx_chip structure to allow
differentiating those chips by known chip id
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
88E6393X/88E6193X/88E6191X switches have in fact 8 internal PHYs, but those
are not present starting at port 0: supported ports go from 1 to 8
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mv88e6xxx currently assumes that switch equipped with internal phys have
those phys mapped contiguously starting from port 0 (see
mv88e6xxx_phy_is_internal). However, some switches have internal PHYs but
NOT starting from port 0. For example 88e6393X, 88E6193X and 88E6191X have
integrated PHYs available on ports 1 to 8
To properly support this offset, add a new field to allow specifying an
internal PHYs layout. If field is not set, default layout is assumed (start
at port 0)
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure to use existing helper to get internal PHYs count instead of
redoing it manually
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since this function is a simple helper, we do not need to pass a full
dsa_switch structure, we can directly pass the mv88e6xxx_chip structure.
Doing so will allow to share this function with any other function
not manipulating dsa_switch structure but needing info about number of
internal phys
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no gpiod_export() and gpiod_unexport() looks pretty much stray.
The gpiod_export() and gpiod_unexport() shouldn't be used in the code,
GPIO sysfs is deprecated. That said, simply drop the stray call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230528142531.38602-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This update introduces specific register access boundaries for the
KSZ8873 and KSZ8863 chips within the DSA Microchip driver. The outlined
ranges target global control registers, port registers, and advanced
control registers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch prepares the ksz8863_smi part of ksz8 driver to utilize the
regmap register access validation feature.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The only place where this variable would be set to false is the
ksz8_config_cpu_port() function. But it is done in a bogus way:
for (i = 0; i < dev->phy_port_cnt; i++) {
if (i == dev->phy_port_cnt) <--- will be never executed.
break;
p->on = 1;
So, we never have a situation where p->on = 0. In this case, we can just
remove it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It is not immediately obvious that this driver allocates, via the
KSZ_REGMAP_TABLE() macro, 3 regmaps for register access: dev->regmap[0]
for 8-bit access, dev->regmap[1] for 16-bit and dev->regmap[2] for
32-bit access.
In future changes that add support for reg_fields, each field will have
to specify through which of the 3 regmaps it's going to go. Add an enum
now, to denote one of the 3 register access widths, and make the code go
through some wrapper functions for easier review and further
modification.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch refines the error handling mechanism for 8-bit register
read-modify-write operations. In case of a failure, it now logs an error
message detailing the problematic offset. This enhancement aids in
debugging by providing more precise information when these operations
encounter issues.
Furthermore, the ksz_prmw8() function has been updated to return error
values rather than void, enabling calling functions to appropriately
respond to errors.
Additionally, in case of an error that affects both the current and
future accesses, the PHY driver will log the errors consistently, akin
to the existing behavior in all ksz_read*/ksz_write* helpers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use the newly introduced lynx_pcs_create_mdiodev() which simplifies the
creation and destruction of the lynx PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the link forcing out of mac_config() and into the mac_prepare()
and mac_finish() methods. This results in no change to the order in
which these operations are performed, but does mean when we convert
mv88e6xxx to phylink_pcs support, we will continue to preserve this
ordering.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to datasheet, the command opcode must be specified
into bits [14:12] of the Extended Port Control register (EPC).
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marco Migliore <m.migliore@tiesse.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ports are in standalone mode, they should have learning disabled to
avoid adding new entries in the MAC lookup table which might be used by
other bridge ports to forward packets. While adding that, also make sure
learning is enabled for CPU port.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stp_set_state() should actually allow receiving BPDU while in LEARNING
mode which is not the case. Additionally, the BLOCKEN bit does not
actually forbid sending forwarded frames from that port. To fix this, add
a5psw_port_tx_enable() function which allows to disable TX. However, while
its name suggest that TX is totally disabled, it is not and can still
allow to send BPDUs even if disabled. This can be done by using forced
forwarding with the switch tagging mechanism but keeping "filtering"
disabled (which is already the case in the rzn1-a5sw tag driver). With
these fixes, STP support is now functional.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, management frame were discarded before reaching the CPU port due
to a misconfiguration of the MGMT_CONFIG register. Enable them by setting
the correct value in this register in order to correctly receive management
frame and handle STP.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On mt753x_cpu_port_enable() there's code that enables flooding for the CPU
port only. Since mt753x_cpu_port_enable() runs twice when both CPU ports
are enabled, port 6 becomes the only port to forward the frames to. But
port 5 is the active port, so no frames received from the user ports will
be forwarded to port 5 which breaks network connectivity.
Every bit of the BC_FFP, UNM_FFP, and UNU_FFP bits represents a port. Fix
this issue by setting the bit that corresponds to the CPU port without
overwriting the other bits.
Clear the bits beforehand only for the MT7531 switch. According to the
documents MT7621 Giga Switch Programming Guide v0.3 and MT7531 Reference
Manual for Development Board v1.0, after reset, the BC_FFP, UNM_FFP, and
UNU_FFP bits are set to 1 for MT7531, 0 for MT7530.
The commit 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user
ports") silently changed the method to set the bits on the MT7530_MFC.
Instead of clearing the relevant bits before mt7530_cpu_port_enable()
which runs under a for loop, the commit started doing it on
mt7530_cpu_port_enable().
Back then, this didn't really matter as only a single CPU port could be
used since the CPU port number was hardcoded. The driver was later changed
with commit 1f9a6abecf ("net: dsa: mt7530: get cpu-port via dp->cpu_dp
instead of constant") to retrieve the CPU port via dp->cpu_dp. With that,
this silent change became an issue for when using multiple CPU ports.
Fixes: 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user ports")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multi-chip module MT7530 switch with a 40 MHz oscillator on the
MT7621AT, MT7621DAT, and MT7621ST SoCs forwards corrupt frames using
trgmii.
This is caused by the assumption that MT7621 SoCs have got 150 MHz PLL,
hence using the ncpo1 value, 0x0780.
My testing shows this value works on Unielec U7621-06, Bartel's testing
shows it won't work on Hi-Link HLK-MT7621A and Netgear WAC104. All devices
tested have got 40 MHz oscillators.
Using the value for 125 MHz PLL, 0x0640, works on all boards at hand. The
definitions for 125 MHz PLL exist on the Banana Pi BPI-R2 BSP source code
whilst 150 MHz PLL don't.
Forwarding frames using trgmii on the MCM MT7530 switch with a 25 MHz
oscillator on the said MT7621 SoCs works fine because the ncpo1 value
defined for it is for 125 MHz PLL.
Change the 150 MHz PLL comment to 125 MHz PLL, and use the 125 MHz PLL
ncpo1 values for both oscillator frequencies.
Link: 81d24bbce7/u-boot-mt/drivers/net/rt2880_eth.c (L2195)
Fixes: 7ef6f6f8d2 ("net: dsa: mt7530: Add MT7621 TRGMII mode support")
Tested-by: Bartel Eerdekens <bartel.eerdekens@constell8.be>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rsvd2cpu capability for mv88e6321 model, to allow proper bpdu
processing.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Fixes: 51c901a775 ("net: dsa: mv88e6xxx: distinguish Global 2 Rsvd2CPU")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With LEDS_CLASS=m, a built-in qca8k driver fails to link:
arm-linux-gnueabi-ld: drivers/net/dsa/qca/qca8k-leds.o: in function `qca8k_setup_led_ctrl':
qca8k-leds.c:(.text+0x1ea): undefined reference to `devm_led_classdev_register_ext'
Change the dependency to avoid the broken configuration.
Fixes: 1e264f9d29 ("net: dsa: qca8k: add LEDs basic support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230420213639.2243388-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two variants of the MT7531 switch IC which got different
features (and pins) regarding port 5:
* MT7531AE: SGMII/1000Base-X/2500Base-X SerDes PCS
* MT7531BE: RGMII
Moving the creation of the SerDes PCS from mt753x_setup to mt7530_probe
with commit 6de2852297 ("net: dsa: mt7530: move SGMII PCS creation
to mt7530_probe function") works fine for MT7531AE which got two
instances of mtk-pcs-lynxi, however, MT7531BE requires mt7531_pll_setup
to setup clocks before the single PCS on port 6 (usually used as CPU
port) starts to work and hence the PCS creation failed on MT7531BE.
Fix this by introducing a pointer to mt7531_create_sgmii function in
struct mt7530_priv and call it again at the end of mt753x_setup like it
was before commit 6de2852297 ("net: dsa: mt7530: move SGMII PCS
creation to mt7530_probe function").
Fixes: 6de2852297 ("net: dsa: mt7530: move SGMII PCS creation to mt7530_probe function")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/ZDvlLhhqheobUvOK@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because of the logic in place, SW_HUGE_PACKET can never be set.
(If the first condition is true, then the 2nd one is also true, but is not
executed)
Change the logic and update each bit individually.
Fixes: 29d1e85f45 ("net: dsa: microchip: ksz8: add MTU configuration support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/43107d9e8b5b8b05f0cbd4e1f47a2bb88c8747b2.1681755535.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add LEDs blink_set() support to qca8k Switch Family.
These LEDs support hw accellerated blinking at a fixed rate
of 4Hz.
Reject any other value since not supported by the LEDs switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs basic support for qca8k Switch Family by adding basic
brightness_set() support.
Since these LEDs refelect port status, the default label is set to
":port". DT binding should describe the color and function of the
LEDs using standard LEDs api.
Each LED always have the device name as prefix. The device name is
composed from the mii bus id and the PHY addr resulting in example
names like:
- qca8k-0.0:00:amber:lan
- qca8k-0.0:00:white:lan
- qca8k-0.0:01:amber:lan
- qca8k-0.0:01:white:lan
These LEDs supports only blocking variant of the brightness_set()
function since they can sleep during access of the switch leds to set
the brightness.
While at it add to the qca8k header file each mode defined by the Switch
Documentation for future use.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move qca8k_port_to_phy() to qca8k header as it's useful for future
reference in Switch LEDs module since the same logic is applied to get
the right index of the switch port.
Make it inline as it's simple function that just decrease the port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to not transmit (preemptible) frames which will be received by
the link partner as corrupted (because it doesn't support FP), the
hardware requires the driver to program the QSYS_PREEMPTION_CFG_P_QUEUES
register only after the MAC Merge layer becomes active (verification
succeeds, or was disabled).
There are some cases when FP is known (through experimentation) to be
broken. Give priority to FP over cut-through switching, and disable FP
for known broken link modes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
