To debug link issues in the field, serdes Tx/Rx equalizer values
help to determine the health of serdes lane.
Extend 'ethtool -d' option to dump serdes Tx/Rx equalizer.
The following list of equalizer param is supported
a. rx_equalization_pre2
b. rx_equalization_pre1
c. rx_equalization_post1
d. rx_equalization_bflf
e. rx_equalization_bfhf
f. rx_equalization_drate
g. tx_equalization_pre1
h. tx_equalization_pre3
i. tx_equalization_atten
j. tx_equalization_post1
k. tx_equalization_pre2
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anil Samal <anil.samal@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240709202951.2103115-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To debug link issues in the field, it is paramount to
dump fec corrected/uncorrected block counts from firmware.
Firmware requires PCS quad number and PCS port number to
read FEC statistics. Current driver implementation does
not maintain above physical properties of a port.
Add new driver API to derive physical properties of an input
port.These properties include PCS quad number, PCS port number,
serdes lane count, primary serdes lane number.
Extend ethtool option '--show-fec' to support fec statistics.
The IEEE standard mandates two sets of counters:
- 30.5.1.1.17 aFECCorrectedBlocks
- 30.5.1.1.18 aFECUncorrectableBlocks
Standard defines above statistics per lane but current
implementation supports total FEC statistics per port
i.e. sum of all lane per port. Find sample output below
FEC parameters for ens21f0np0:
Supported/Configured FEC encodings: Auto RS BaseR
Active FEC encoding: RS
Statistics:
corrected_blocks: 0
uncorrectable_blocks: 0
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anil Samal <anil.samal@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240709202951.2103115-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the support for 200G phy speeds and the mapping for their
advertisement in link. Add the new PHY type bits for AQ command, as
needed for 200G E830 controllers.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Co-developed-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some link modes can be more accurately reported due to newer link mode
values that have been added to the kernel; update those PHY type to report
modes that better reflect the link mode.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor ice_phy_type_to_ethtool to use phy_type_[low|high]_lkup table to
map PHY type to AQ link speed and ethtool link mode. This removes
complexity and simplifies future changes.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
