In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All EtherAVB instances on R-Car Gen3/Gen4 SoCs support the RGMII
interface. In addition, the first two EtherAVB instances on R-Car V4M
also support the MII interface, but this is not yet supported by the
driver.
Add support for MII on R-Car Gen4 by adding an R-Car Gen4-specific EMAC
initialization function that selects the MII clock instead of the RGMII
clock when the PHY interface is MII. Note that all implementations of
EtherAVB on R-Car Gen4 SoCs have the APSR register, but only MII-capable
instances are documented to have the MIISELECT bit, which has a
documented value of zero when reserved.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://patch.msgid.link/3a21d1d6680864aa85afff9260234c2b8054020a.1719234830.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch makes multiple changes that can't be separated:
1) Allocate plain RX buffers via a page pool instead of allocating
SKBs, then use build_skb() when a packet is received.
2) For GbEth IP, reduce the RX buffer size to 2kB.
3) For GbEth IP, merge packets which span more than one RX descriptor
as SKB fragments instead of copying data.
Implementing (1) without (2) would require the use of an order-1 page
pool (instead of an order-0 page pool split into page fragments) for
GbEth.
Implementing (2) without (3) would leave us no space to re-assemble
packets which span more than one RX descriptor.
Implementing (3) without (1) would not be possible as the network stack
expects to use put_page() or page_pool_put_page() to free SKB fragments
after an SKB is consumed.
RX checksum offload support is adjusted to handle both linear and
nonlinear (fragmented) packets.
This patch gives the following improvements during testing with iperf3.
* RZ/G2L:
* TCP RX: same bandwidth at -43% CPU load (70% -> 40%)
* UDP RX: same bandwidth at -17% CPU load (88% -> 74%)
* RZ/G2UL:
* TCP RX: +30% bandwidth (726Mbps -> 941Mbps)
* UDP RX: +417% bandwidth (108Mbps -> 558Mbps)
* RZ/G3S:
* TCP RX: +64% bandwidth (562Mbps -> 920Mbps)
* UDP RX: +420% bandwidth (90Mbps -> 468Mbps)
* RZ/Five:
* TCP RX: +217% bandwidth (145Mbps -> 459Mbps)
* UDP RX: +470% bandwidth (20Mbps -> 114Mbps)
There is no significant impact on bandwidth or CPU load in testing on
RZ/G2H or R-Car M3N.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
NAPI Threaded mode (along with the previously enabled SW IRQ Coalescing)
is required to improve network stack performance for single core SoCs
using the GbEth IP (currently the RZ/G2L SoC family and the RZ/G3S SoC).
This patch gives the following improvements during testing with iperf3.
* RZ/G2UL:
* TCP TX: +32% bandwidth (638Mbps -> 841Mbps)
* TXP RX: +8.8% bandwidth (667Mbps -> 726Mbps)
* UDP RX: +104% bandwidth (53Mbps -> 108Mbps)
* RZ/G3S:
* TCP TX: 29% bandwidth (529Mbps -> 681Mbps)
* UDP RX: +1290% bandwidth (6.46Mbps -> 90Mbps)
* RZ/Five:
* UDP RX: Test no longer crashes (0 -> 20 Mbps)
This patch gives the following reductions in performance in the same
testing:
* RZ/G2UL:
* UDP TX: -7.5% bandwidth (594Mbps -> 549Mbps)
* RZ/G3S:
* UDP TX: -5% bandwidth (625Mbps -> 594Mbps)
These losses are considered acceptable given the benefits shown above.
If UDP TX bandwidth must be maximised for a particular use case, NAPI
threaded mode can be disabled at runtime via sysfs writes.
The improvement of UDP RX bandwidth for the single core SoCs (RZ/G2UL &
RZ/G3S) is particularly critical.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Software IRQ Coalescing is required to improve network stack performance
in the RZ/G2L SoC family and the RZ/G3S SoC, i.e. the SoCs which use the
GbEth IP.
This patch gives the following improvements during testing with iperf3:
* RZ/G2L:
* TCP RX: same bandwidth with -6% CPU load (76% -> 71%)
* UDP RX: same bandwidth with -10% CPU load (99% -> 89%)
* RZ/G2UL:
* UDP RX: +4200% bandwidth (1.23Mbps -> 53Mbps)
* RZ/G3S:
* UDP RX: +425% bandwidth (1.23Mbps -> 6.46Mbps)
The improvement of UDP RX bandwidth for the single core SoCs (RZ/G2UL &
RZ/G3S) is particularly critical.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We can reduce code duplication in ravb_rx_gbeth().
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
To reduce code duplication, we add a new RX ring refill function which
can handle both the initial RX ring population (which was split between
ravb_ring_init() and ravb_ring_format()) and the RX ring refill after
polling (in ravb_rx()).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Align ravb_poll() with the documentation in
`Documentation/networking/kapi.rst` and
`Documentation/networking/napi.rst`.
The documentation says that we should prefer napi_complete_done() over
napi_complete(), and using the former allows us to properly support busy
polling. We should ensure that napi_complete_done() is only called if
the work budget has not been exhausted, and we should only re-arm
interrupts if it returns true.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We don't need to pass the work budget to ravb_rx() by reference, it's
cleaner to pass this by value and return the amount of work done. This
allows us to simplify the ravb_poll() function and use the common
`work_done` variable name seen in other network drivers for consistency
and ease of understanding.
This is a pure refactor and should not affect behaviour.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RX byte accounting for jumbo packets was changed to fix a potential
use-after-free bug. However, that fix used the wrong variable and so
only accounted for the number of bytes in the final descriptor, not the
number of bytes in the whole packet.
To fix this, we can simply update our stats with the correct number of
bytes before calling napi_gro_receive().
Also rename pkt_len to desc_len in ravb_rx_gbeth() to avoid any future
confusion. The variable name pkt_len is correct in ravb_rx_rcar() as
that function does not handle packets spanning multiple descriptors.
Fixes: 5a5a3e564d ("ravb: Fix potential use-after-free in ravb_rx_gbeth()")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Sending a 7kB ping packet to the RZ/G2L in v6.9-rc2 causes the following
backtrace:
WARNING: CPU: 0 PID: 0 at include/linux/skbuff.h:3127 skb_trim+0x30/0x38
Hardware name: Renesas SMARC EVK based on r9a07g044l2 (DT)
pc : skb_trim+0x30/0x38
lr : ravb_rx_csum_gbeth+0x40/0x90
Call trace:
skb_trim+0x30/0x38
ravb_rx_gbeth+0x56c/0x5cc
ravb_poll+0xa0/0x204
__napi_poll+0x38/0x17c
This is caused by ravb_rx_gbeth() calling ravb_rx_csum_gbeth() with the
wrong skb for a packet which spans multiple descriptors. To fix this,
use the correct skb.
Fixes: c2da940857 ("ravb: Add Rx checksum offload support for GbEth")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The RX loops in ravb_rx_gbeth() and ravb_rx_rcar() skip to the next loop
iteration if a zero-length descriptor is seen (indicating a DMA mapping
error). However, the current RX descriptor index `priv->cur_rx[q]` was
incremented at the end of the loop and so would not be incremented when
we skip to the next loop iteration. This would cause the loop to keep
seeing the same zero-length descriptor instead of moving on to the next
descriptor.
As the loop counter `i` still increments, the loop would eventually
terminate so there is no risk of being stuck here forever - but we
should still fix this to avoid wasting cycles.
To fix this, the RX descriptor index is incremented at the top of the
loop, in the for statement itself. The assignments of `entry` and `desc`
are brought into the loop to avoid the need for duplication.
Fixes: d8b48911fd ("ravb: fix ring memory allocation")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The units of "work done" in the RX path should be packets instead of
descriptors.
Descriptors which are used by the hardware to record error conditions or
are empty in the case of a DMA mapping error should not count towards
our RX work budget.
Also make the limit variable unsigned as it can never be negative.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The error statistics should be updated each time the poll function is
called, even if the full RX work budget has been consumed. This prevents
the counts from becoming stuck when RX bandwidth usage is high.
This also ensures that error counters are not updated after we've
re-enabled interrupts as that could result in a race condition.
Also drop an unnecessary space.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20240402145305.82148-2-paul.barker.ct@bp.renesas.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The TX queue should be serviced each time the poll function is called,
even if the full RX work budget has been consumed. This prevents
starvation of the TX queue when RX bandwidth usage is high.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20240402145305.82148-1-paul.barker.ct@bp.renesas.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver used the DT node of the device itself when registering the
MDIO bus. While this works, it creates a problem: it forces any MDIO bus
properties to also be set on the devices DT node. This mixes the
properties of two distinctly different things and is confusing.
This change adds support for an optional mdio node to be defined as a
child to the device DT node. The child node can then be used to describe
MDIO bus properties that the MDIO core can act on when registering the
bus.
If no mdio child node is found the driver fallback to the old behavior
and register the MDIO bus using the device DT node. This change is
backward compatible with old bindings in use.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240325153451.2366083-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When creating a helper to allocate and align an skb one location where
the skb data size was updated was missed. This can lead to a warning
being printed when the memory is being unmapped as it now always unmap
the maximum frame size, instead of the size after it have been
aligned.
This was correctly done for RZ/G2L but missed for R-Car.
Fixes: cfbad64706 ("ravb: Create helper to allocate skb and align it")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240308224237.496924-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The R-Car and RZ/G2L Rx code paths were split in two separate
implementations when support for RZ/G2L was added due to the fact that
R-Car uses the extended descriptor format while RZ/G2L uses normal
descriptors. This has led to a duplication of Rx logic with the only
difference being the different Rx descriptors types used. The
implementation however neglects to take into account that extended
descriptors are normal descriptors with additional metadata at the end
to carry hardware timestamp information.
The hardware timestamp information is only consumed in the R-Car Rx
loop and all the maintenance code around the Rx ring can be shared
between the two implementations if the difference in descriptor length
is carefully considered.
This change merges the two implementations for Rx ring maintenance by
adding a method to access both types of descriptors as normal
descriptors, as this part covers all the fields needed for Rx ring
maintenance the only difference between using normal or extended
descriptor is the size of the memory region to allocate/free and the
step size between each descriptor in the ring.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make it possible to merge the R-Car and RZ/G2L code paths move the
maximum usable size of a single Rx descriptor data slice into the
hardware information instead of using two different defines in the two
different code paths.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the define describing the RZ/G2L maximum frame size and only use
the information in the hardware information struct. This will make it
easier to merge the R-Car and RZ/G2L code paths.
There is no functional change as both the define and the maximum frame
length in the hardware information is set to 8K.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EtherAVB device requires the SKB data to be aligned to 128 bytes.
The alignment is done by allocating an skb 128 bytes larger than the
maximum frame size supported by the device and adjusting the headroom to
fit the requirement.
This code has been refactored a few times and small issues have been
added along the way. The issues are not harmful but prevent merging
parts of the Rx code which have been split in two implementations with
the addition of RZ/G2L support, a device that supports larger frame
sizes.
This change removes the need for duplicated and somewhat inaccurate
hardware alignment constrains stored in the hardware information struct
by creating a helper to handle the allocation of an skb and alignment of
an skb data.
For the R-Car class of devices the maximum frame size is 4K and each
descriptor is limited to 2K of data. The current implementation does not
support split descriptors, this limits the frame size to 2K. The
current hardware information however records the descriptor size just
under 2K due to bad understanding of the device when larger MTUs where
added.
For the RZ/G2L device the maximum frame size is 8K and each descriptor
is limited to 4K of data. The current hardware information records this
correctly, but it gets the alignment constrains wrong as just aligns it
by 128, it does not extend it by 128 bytes to allow the full frame to be
stored. This works because the RZ/G2L device supports split descriptors
and allocates each skb to 8K and aligns each 4K descriptor in this
space.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct member rx_max_buf_size was added before split descriptor
support was added. It is unclear if the value describes the full skb
frame buffer or the data descriptor buffer which can be combined into a
single skb.
Rename it to make it clear it referees to the maximum frame size and can
cover multiple descriptors.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx ring can either be made up of normal or extended descriptors, not
a mix of the two at the same time. Make this explicit by grouping the
two variables in a rx_ring union.
The extension of the storage for more than one queue of normal
descriptors from a single to NUM_RX_QUEUE queues have no practical
effect. But aids in making the code readable as the code that uses it
already piggyback on other members of struct ravb_private that are
arrays of max length NUM_RX_QUEUE, e.g. rx_desc_dma. This will also make
further refactoring easier.
While at it, rename the normal descriptor Rx ring to make it clear it's
not strictly related to the GbEthernet E-MAC IP found in RZ/G2L, normal
descriptors could be used on R-Car SoCs too.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add runtime PM support for the ravb driver. As the driver is used by
different IP variants, with different behaviors, to be able to have the
runtime PM support available for all devices, the preparatory commits
moved all the resources parsing and allocations in the driver's probe
function and kept the settings for ravb_open(). This is due to the fact
that on some IP variants-platforms tuples disabling/enabling the clocks
will switch the IP to the reset operation mode where register contents is
lost and reconfiguration needs to be done. For this the rabv_open()
function enables the clocks, switches the IP to configuration mode, applies
all the register settings and switches the IP to the operational mode. At
the end of ravb_open() IP is ready to send/receive data.
In ravb_close() necessary reverts are done (compared with ravb_open()), the
IP is switched to reset mode and clocks are disabled.
The ethtool APIs or IOCTLs that might execute while the interface is down
are either cached (and applied in ravb_open()) or rejected (as at that time
the IP is in reset mode). Keeping the IP in the reset mode also increases
the power saved (according to the hardware manual).
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not apply features to hardware if the interface is down. In case runtime
PM is enabled, and while the interface is down, the IP will be in reset
mode (as for some platforms disabling the clocks will switch the IP to
reset mode, which will lead to losing register contents) and applying
settings in reset mode is not an option. Instead, cache the features and
apply them in ravb_open() through ravb_emac_init().
To avoid accessing the hardware while the interface is down
pm_runtime_active() check was introduced. Along with it the device runtime
PM usage counter has been incremented to avoid disabling the device clocks
while the check is in progress (if any).
Commit prepares for the addition of runtime PM.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c2da940857 ("ravb: Add Rx checksum offload support for GbEth")
introduced support for setting GbEth features. With this the IP-specific
features update functions update the ndev->features individually.
Next commits add runtime PM support for the ravb driver. The runtime PM
implementation will enable/disable the IP clocks on
the ravb_open()/ravb_close() functions. Accessing the IP registers with
clocks disabled blocks the system.
The ravb_set_features() function could be executed when the Ethernet
interface is closed so we need to ensure we don't access IP registers while
the interface is down when runtime PM support will be in place.
For these, move the update of ndev->features to ravb_set_features(). In
this way we update the ndev->features only when the IP-specific features
set function returns success and we can avoid code duplication when
introducing runtime PM registers protection.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return the cached statistics in case the interface is down. There should be
no drawback to this, as cached statistics are updated in ravb_close().
In order to avoid accessing the IP registers while the IP is runtime
suspended pm_runtime_active() check was introduced. The device runtime
PM usage counter has been incremented to avoid disabling the device clocks
while the check is in progress (if any).
The commit prepares the code for the addition of runtime PM support.
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the reverse order of operations in ravb_close() when compared with
ravb_open(). This is the recommended configuration sequence.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 4th argument of ravb_setup_irq() is used to save the IRQ number that
will be further used by the driver code. Not all ravb_setup_irqs() calls
need to save the IRQ number. The previous code used to pass a dummy
variable as the 4th argument in case the IRQ is not needed for further
usage. That is not necessary as the code from ravb_setup_irq() can detect
by itself if the IRQ needs to be saved. Thus, get rid of the code that is
not needed.
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The units of "work done" in the RX path should be packets instead of
descriptors, as large packets can be spread over multiple descriptors.
Fixes: 1c59eb678c ("ravb: Fillup ravb_rx_gbeth() stub")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20240214151204.2976-1-paul.barker.ct@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TOE has hardware support for calculating IP header and TCP/UDP/ICMP
checksum for both IPv4 and IPv6.
Add Tx checksum offload supported by TOE for IPv4 and TCP/UDP.
For Tx, the result of checksum calculation is set to the checksum field of
each IPv4 Header/TCP/UDP/ICMP of ethernet frames. For the unsupported
frames, those fields are not changed. If a transmission frame is an UDPv4
frame and its checksum value in the UDP header field is 0x0000, TOE does
not calculate checksum for UDP part of this frame as it is optional
function as per standards.
We can test this functionality by the below commands
ethtool -K eth0 tx on --> to turn on Tx checksum offload
ethtool -K eth0 tx off --> to turn off Tx checksum offload
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20240207092838.160627-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TOE has hardware support for calculating IP header and TCP/UDP/ICMP
checksum for both IPv4 and IPv6.
Add Rx checksum offload supported by TOE for IPv4 and TCP/UDP protocols.
For Rx, the 4-byte result of checksum calculation is attached to the
Ethernet frames.First 2-bytes is result of IPv4 header checksum and next
2-bytes is TCP/UDP/ICMP checksum.
If a frame does not have checksum error, 0x0000 is attached as checksum
calculation result. For unsupported frames 0xFFFF is attached as checksum
calculation result. In case of an IPv6 packet, IPv4 checksum is always set
to 0xFFFF.
We can test this functionality by the below commands
ethtool -K eth0 rx on --> to turn on Rx checksum offload
ethtool -K eth0 rx off --> to turn off Rx checksum offload
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20240207092838.160627-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove explicit calls to functions that are called by ravb_open(). There is
no need to have them doubled now that the ravb_open() already contains
what is needed for the interface configuration. Along with it,
configurations needed by PTP were moved to ravb_wol_restore(). With this,
code in ravb_resume() becomes simpler.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As ravb_close() contains now the call to ravb_ptp_stop() for both ccc_gac
and gPTP aware platforms, there is no need to keep the separate call in
ravb_suspend(). Instead, move it to ravb_wol_setup(). In this way the
resulting code is cleaner.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As some IP variants switch to reset mode (and thus the register contents is
lost) when setting clocks (due to module standby functionality) to be able
to implement runtime PM and save more power, set the IP's operating mode to
reset at the end of the probe. Along with it, in the ndo_open API the IP
will be switched to configuration, then operation mode. In the ndo_close
API, the IP will be switched back to reset mode. This allows implementing
runtime PM and, along with it, save more power when the IP is not used.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The initialization sequence for PTP is the same for platforms with ccc_gac
and gptp (according to "Figure 50.71 Flow of gPTP Initialization (Normal,
Common to All Modes)" of the R-Car Series, 3rd generation hardware
manual and "Figure 37A.53 Flow of gPTP Initialization (Normal, Common to
All Modes)" of the RZ/G Series hardware manual).
As some IP variants switch to reset mode (and thus the registers content is
lost) when setting clocks (due to module standby functionality) to be able
to implement runtime PM, move the PTP initialization to the driver's
ndo_open API.
This commit prepares the code for the addition of runtime PM.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
DBAT setup was done in the driver's probe API. As some IP variants switch
to reset mode (and thus registers content is lost) when setting clocks
(due to module standby functionality) to be able to implement runtime PM
move the DBAT configuration in the driver's ndo_open API.
This commit prepares the code for the addition of runtime PM.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Delay parsing and setting were done in the driver's probe API. As some IP
variants switch to reset mode (and thus the register contents is lost) when
setting clocks (due to module standby functionality) to be able to
implement runtime PM keep the delay parsing in the driver's probe function
and move the delay applying function to the driver's ndo_open API.
Along with it, ravb_parse_delay_mode() function was moved close to
ravb_set_delay_mode() function to have the delay specific code in the
same place.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ravb_set_gti() was computing the value of GTI based on the reference clock
rate and then applied it to register. This was done on the driver's probe
function. In order to implement runtime PM for all IP variants (as some IP
variants switches to reset mode (and thus the registers content is lost)
when module standby is configured through clock APIs) the GTI setup was
split in 2 parts: one computing the value of the GTI register (done in the
driver's probe function) and one applying the computed value to register
(done in the driver's ndo_open API).
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The runtime PM implementation will disable clocks at the end of
ravb_probe(). As some IP variants switch to reset mode as a result of
setting module standby through clock disable APIs, to implement runtime PM
the resource parsing and requesting are moved in the probe function and IP
settings are moved in the open function. This is done because at the end of
the probe some IP variants will switch anyway to reset mode and the
registers content is lost. Also keeping only register settings operations
in the ravb_open()/ravb_close() functions will make them faster.
Commit moves IRQ requests to ravb_probe() to have all the IRQs ready when
the interface is open. As now getting/requesting IRQs is done in a single
place there is no need to keep intermediary data (like ravb_rx_irqs[] and
ravb_tx_irqs[] arrays or IRQs in struct ravb_private).
In order to avoid accessing the IP registers while the IP is runtime
suspended (e.g. in the timeframe b/w the probe requests shared IRQs and
IP clocks are enabled) in the interrupt handlers were introduced
pm_runtime_active() checks. The device runtime PM usage counter has been
incremented to avoid disabling the device's clocks while the check is in
progress (if any).
This is a preparatory change to add runtime PM support for all IP variants.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reference clock could be or not be part of the power domain. If it is part
of the power domain, the power domain takes care of properly setting it. In
case it is not part of the power domain and full runtime PM support is
available in driver the clock will not be propertly disabled/enabled at
runtime. For this, keep the prepare/unprepare operations in the driver's
probe()/remove() functions and move the enable/disable in runtime PM
functions.
By doing this, the previous ravb_runtime_nop() function was renamed
ravb_runtime_suspend() and the comment was removed. A proper runtime PM
resume function was added (ravb_runtime_resume()). The current driver
still don't need to make any register settings on runtime suspend/resume
(as expressed in the removed comment) because, currently,
pm_runtime_put_sync() is called on the driver remove function. This will be
changed in the next commits (that extends the runtime PM support) such
that proper register settings (along with runtime resume/suspend) will be
done on ravb_open()/ravb_close().
Along with it, the other clock request operations were moved close to
reference clock request and prepare to have all the clock requests
specific code grouped together.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
RZ/G3S can go to deep sleep states where power to most of the SoC parts is
off. When resuming from such a state, the Ethernet controller needs to be
reinitialized. De-asserting the reset signal for it should also be done.
Thus, add reset assert/de-assert on suspend/resume functions.
On the resume function, the de-assert was not reverted in case of failures
to give the user a chance to restore the interface (e.g., bringing down/up
the interface) in case suspend/resume failed.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use tabs instead of spaces in the ravb_set_rate_gbeth() function.
This aligns with the coding style requirements.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
