On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.
Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
changed from 10gbase-r to 2500base-x due to copper change in speed
from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
its interface to the host, or the interrupt about loss of SerDes link
hadn't arrived yet (there can be a delay of several milliseconds for
this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
- phylink_mac_pcs_get_state()
- this fills in speed=10g link=up
- interface mode is updated to 2500base-x but speed is left at 10Gbps
- phylink_major_config()
- interface is changed to 2500base-x
- phylink_link_up()
- mv88e6xxx_mac_link_up()
- .port_set_speed_duplex()
- speed is set to 10Gbps
- reports "Link is Up - 10Gbps/Full" to dmesg
Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.
To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 4904b6ea1f ("net: phy: phylink: Use PHY device interface if
N/A") introduced handling for the phy interface mode where this is not
known at phylink creation time. This was never added to the OF/fwnode
paths, but is necessary when the phy is present in DT, but the phy-mode
is not specified.
Add this handling.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices expose memory-mapped c22-compliant PHYs. Because these
devices do not have an MDIO bus, we cannot use the existing helpers.
Refactor the existing helpers to allow supplying the values for c22
registers directly, instead of using MDIO to access them. Only get_state
and set_advertisement are converted, since they contain the most complex
logic. Because set_advertisement is never actually used outside
phylink_mii_c22_pcs_config, move the MDIO-writing part into that
function. Because some modes do not need the advertisement register set
at all, we use -EINVAL for this purpose.
Additionally, a new function phylink_pcs_enable_an is provided to
determine whether to enable autonegotiation.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
1000base-KX was missed in phylink_caps_to_linkmodes(), add it. This
will be necessary to convert stmmac with xpcs to ensure we don't drop
any supported linkmodes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMII has not been documented in the kernel, but information on this PHY
interface mode has been recently found. Document it, and correct the
recently introduced phylink handling for this interface mode.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1mmfVl-0075nP-14@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a generic validate() implementation using the supported_interfaces
and a bitmask of MAC pause/speed/duplex capabilities. This allows us
to entirely eliminate many driver private validate() implementations.
We expose the underlying phylink_get_linkmodes() function so that
drivers which have special needs can still benefit from conversion.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta does not support asymetric pause modes, and it flags this by the
lack of AsymPause in the supported field. When setting pause modes, we
check that pause->rx_pause == pause->tx_pause, but only when pause
autoneg is enabled. When pause autoneg is disabled, we still allow
pause->rx_pause != pause->tx_pause, which is incorrect when the MAC
does not support asymetric pause, and causes mvneta to issue a warning.
Fix this by removing the test for pause->autoneg, so we always check
that pause->rx_pause == pause->tx_pause for network devices that do not
support AsymPause.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the network device supplies a supported interface bitmap, we can use
that during phylink's validation to simplify MAC drivers in two ways by
using the supported_interfaces bitmap to:
1. reject unsupported interfaces before calling into the MAC driver.
2. generate the set of all supported link modes across all supported
interfaces (used mainly for SFP, but also some 10G PHYs.)
Suggested-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This refactors the phylink pcs helper functions to use mdiobus_* instead
of mdiodev_*.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The auto-negotiation state in the PCS as set by
phylink_mii_c22_pcs_config was previously always enabled when the
driver is configured for in-band autonegotiation, even if
autonegotiation was disabled on the interface with ethtool. Update the
code to set the BMCR_ANENABLE bit based on the interface's
autonegotiation enabled state.
Update phylink_mii_c22_pcs_get_state to not check
autonegotiation-related fields when autonegotiation is disabled.
Update phylink_mac_pcs_get_state to initialize the state based on the
interface's configured speed, duplex and pause parameters rather than
to unknown when autonegotiation is disabled, before calling the
driver's pcs_get_state functions, as they are not likely to provide
meaningful data for these fields when autonegotiation is disabled. In
this case the driver is really just filling in the link state field.
Note that in cases where there is a downstream PHY connected, such as
with SGMII and a copper PHY, the configuration set by ethtool is
handled by phy_ethtool_ksettings_set and not propagated to the PCS.
This is correct since SGMII or 1000Base-X autonegotiation with the PCS
should normally still be used even if the copper side has disabled it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ea269a6f72 ("net: phylink: Update SFP selected interface on
advertising changes") added a better solution to selecting the
interface mode for SFPs using the advertisement mask. This method will
work for mvneta and mvpp2 when selecting between 2500base-X and
1000base-X without needing to use the basex helper, or indicate that
we support both 1000base-X and 2500base-X when in either of these two
interface modes.
Hence, we need to eliminate the validation prior to selecting the
interface, otherwise when we clean up mvneta's validation function, we
will end up locking to 2500base-X as we validate with an interface mode
of PHY_INERFACE_MODE_2500BASEX.
The supported mask will already have been reduced down to the union of
support for the SFP and MAC already, so we can be confident that the
advertisement mask is already appropriately restricted. We only need to
select the appropriate interface, and then revalidate with the new
interface mode.
We get rid of the check for pl->sfp_port too, this is meaningless here
as it doesn't get cleared when a module is removed, so it doesn't
indicate if a module is present. Just rely on pl->sfp_bus.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the mdiobus_modify_changed() helper in the C22 PCS advertisement
helper.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper for setting 10Gigabit modes, so we have one central
place that sets all appropriate 10G modes for a driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter points out that we have a code path that permits a NULL
netdev pointer to be passed to netif_carrier_off(), which will cause
a kernel oops. In any case, we need to set pl->old_link_state to false
to have the desired effect when there is no netdev present.
Fixes: f97493657c ("net: phylink: add suspend/resume support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently changes to the advertising state via ethtool do not cause any
reselection of the configured interface mode after the SFP is already
inserted and initially configured.
While it is not typical to change the advertised link modes for an
interface using an SFP in certain use cases it is desirable. In the case
of a SFP port that is capable of handling both SFP and SFP+ modules it
will automatically select between 1G and 10G modes depending on the
supported mode of the SFP. However if the SFP module is capable of
working in multiple modes (e.g. a SFP+ DAC that can operate at 1G or
10G), one end of the cable may be attached to a SFP 1000base-x port thus
the SFP+ end must be manually configured to the 1000base-x mode in order
for the link to be established.
This change causes the ethtool setting of advertised mode changes to
reselect the interface mode so that the link can be established.
Additionally when a module is inserted the advertising mode is reset to
match the supported modes of the module.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Zhang reports that Wake-on-Lan with the stmmac ethernet driver broke
when moving the incorrect handling of mac link state out of mac_config().
This reason this breaks is because the stmmac's WoL is handled by the MAC
rather than the PHY, and phylink doesn't cater for that scenario.
This patch adds the necessary phylink code to handle suspend/resume events
according to whether the MAC still needs a valid link or not. This is the
barest minimum for this support.
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Tested-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need to fiddle about with the supported mask after we have
validated the user's requested parameters. Simplify and streamline the
code by moving the linkmode copy and update of the autoneg bit after
validating the user's request.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Augment the phy link debug prints with the pause state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following format issues:
1. open brace '{' following function definitions should go to the next
line.
2. braces {} are not necessary for single line statements.
3. else should follow close brace '}'.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Block comments should not use a trailing */ on a separate line and every
line of a block comment should start with an '*'.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 25gbase-r interface type and speed to phylink.
This is needed for the Sparx5 switch.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor phylink_of_phy_connect() to use phylink_fwnode_phy_connect().
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define phylink_fwnode_phy_connect() to connect phy specified by
a fwnode to a phylink instance.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
if pl->mac_ops->mac_finish() failed, phylink_err should use
"mac_finish" instead of "mac_prepare".
Fixes: b7ad14c2fe ("net: phylink: re-implement interface configuration with PCS")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain platform does not support DT, so we make phylink_parse_mode() to
allow non-DT platform to use it to setup in-band AN advertising.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some functions have different names between their prototypes
and the kernel-doc markup.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Xilinx PCS/PMA PHY requires that BMCR_ISOLATE be disabled for proper
operation in 1000BaseX mode. It should be safe to ensure this bit is
disabled in phylink_mii_c22_pcs_config in all cases.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20201026175802.1332477-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same link partner advertisement word is used for both QSGMII and
SGMII, thus treat both interface modes using the same
phylink_decode_sgmii_word() function.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new addition of the USXGMII link partner ability constants we
can now introduce a phylink helper that decodes the USXGMII word and
populates the appropriate fields in the phylink_link_state structure
based on them.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we intend to use PCS operations, mac_pcs_get_state() will not be
implemented, so will be NULL. If we also intend to register the PCS
operations in mac_prepare() or mac_config(), then this leads to an
attempt to call NULL function pointer during phylink_start(). Avoid
this, but we must report the link is down.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface to configure the advertisement for a clause 22 PCS
PHY, and set the AN enable flag in the BMCR appropriately.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a way for MAC PCS to have private data while keeping independence
from struct phylink_config, which is used for the MAC itself. We need
this independence as we will have stand-alone code for PCS that is
independent of the MAC. Introduce struct phylink_pcs, which is
designed to be embedded in a driver private data structure.
This structure does not include a mdio_device as there are PCS
implementations such as the Marvell DSA and network drivers where this
is not necessary.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
With PCS support, how we implement interface reconfiguration (or other
major reconfiguration) is not up to the job; we end up reconfiguring
the PCS for an interface change while the link could potentially be up.
In order to solve this, add two additional MAC methods for major
configuration, one to prepare for the change, and one to finish the
change.
This allows mvneta and mvpp2 to shutdown what they require prior to the
MAC and PCS configuration calls, and then restart as appropriate.
This impacts ksettings_set(), which now needs to identify whether the
change is a minor tweak to the advertisement masks or whether the
interface mode has changed, and call the appropriate function for that
update.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-code the pause in-band advertisement update in light of the addition
of PCS support, so that we perform the minimum required; only the PCS
configuration function needs to be called in this case, followed by the
request to trigger a restart of negotiation if the programmed
advertisement changed.
We need to change the pcs_config() signature to pass whether resolved
pause should be passed to the MAC for setups such as mvneta and mvpp2
where doing so overrides the MAC manual flow controls.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
For fixed links, we only allow the current settings, so this should be
a matter of merely rejecting an attempt to change the settings. If the
settings agree, then there is nothing more we need to do.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than recomputing whether AN is enabled, use config.an_enabled.
Suggested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have a PHY attached, an ethtool ksettings_set() call only
really needs to call through to the phylib equivalent; phylib will
call back to us when the link changes so we can update our state.
Therefore, we can bypass most of our ksettings_set() call for this
case.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the ksettings_set() implementation to look more like phylib's
implementation; use a switch() for validating the autoneg setting, and
use the linkmode_modify() helper to set the autoneg bit in the
advertisement mask.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid calling mac_config() when using split PCS, and the interface
remains the same.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only PHYs that are used with phylink which change their interface
are the BCM84881 and MV88X3310 family, both of which only change their
interface modes on link-up events. This will break when drivers are
converted to split-PCS. Fix this.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only PHYs that are used with phylink which change their interface
are the BCM84881 and MV88X3310 family, both of which only change their
interface modes on link-up events. However, rather than relying upon
this behaviour by the PHY, we should give a stronger guarantee when
resolving that the link will be down whenever we change the interface
mode. This patch implements that stronger guarantee for resolve.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a boolean to indicate whether mac_config() should be called during
a resolution. This allows resolution to have a single location where
mac_config() will be called, which will allow us to make decisions
about how and what we do.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rejig the link state tracking, so that we can use the current state
in a future patch.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Comparing the ethtool output from phylink and non-phylink fixed-link
setups shows that we have some differences:
- The "auto-negotiation" fields are different; phylink reports these
as "No", non-phylink reports these as "Yes" for the supported and
advertising masks.
- The link partner advertisement is set to the link speed with non-
phylink, but phylink leaves this unset, causing all link partner
fields to be omitted.
The phylink ethtool output also disagrees with the software emulated
PHY dump via the MII registers.
Update the phylink fixed-link parsing code so that we better reflect
the behaviour of the non-phylink code that this facility replaces, and
bring the ethtool interface more into line with the report from via the
MII interface.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
