generic_ocp_write() asks the parameter "size" must be 4 bytes align.
Therefore, write the bp would fail, if the mac->bp_num is odd. Align the
size to 4 for fixing it. The way may write an extra bp, but the
rtl8152_is_fw_mac_ok() makes sure the value must be 0 for the bp whose
index is more than mac->bp_num. That is, there is no influence for the
firmware.
Besides, I check the return value of generic_ocp_write() to make sure
everything is correct.
Fixes: e5c266a611 ("r8152: set bp in bulk")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20240903063333.4502-1-hayeswang@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some docks support MAC pass-through - MAC address
is taken from another device.
Driver should indicate that with NET_ADDR_STOLEN flag.
This should help to avoid collisions if network interface
names are generated with MAC policy.
Reported and discussed here
https://github.com/systemd/systemd/issues/33104
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240605153340.25694-1-gmazyland@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we get to the end of the r8152's suspend() routine and we find that
the USB device is INACCESSIBLE then it means that some of our
preparation for suspend didn't take place. We need a USB reset to get
ourselves back in a consistent state so we can try again and that
can't happen during system suspend. Call pm_wakeup_event() to wake the
system up in this case.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/66590f25.170a0220.8b5ad.1752@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we happened to get a USB transfer error during the transition to
suspend then the usb_queue_reset_device() that r8152_control_msg()
calls will get dropped on the floor. This is because
usb_lock_device_for_reset() (which usb_queue_reset_device() uses)
silently fails if it's called when a device is suspended or if too
much time passes.
Let's resolve this by resetting the device ourselves in r8152's
resume() function.
NOTE: due to timing, it's _possible_ that we could end up with two USB
resets: the one queued previously and the one called from the resume()
patch. This didn't happen in test cases I ran, though it's conceivably
possible. We can't easily know if this happened since
usb_queue_reset_device() can just silently drop the reset request. In
any case, it's not expected that this is a problem since the two
resets can't run at the same time (because of the device lock) and it
should be OK to reset the device twice. If somehow the double-reset
causes problems we could prevent resets from being queued up while
suspend is running.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/66590f22.170a0220.8b5ad.1750@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Someone complains the message appears continuously. This occurs
because the device is woken from UPS mode, and the driver re-loads
the firmware.
When the device enters runtime suspend and cable is unplugged, the
device would enter UPS mode. If the runtime resume occurs, and the
device is woken from UPS mode, the driver has to re-load the firmware
and causes the message. If someone wakes the device continuously, the
message would be shown continuously, too. Use dev_dbg to avoid it.
Note that, the function could be called before register_netdev(), so I
don't use netif_info() or netif_dbg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20240424084532.159649-1-hayeswang@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For the unknown device, rtl8152_cfgselector_choose_configuration()
should return a negative value. Then, usb_choose_configuration() would
set a configuration for CDC ECM or NCM mode. Otherwise, there is no
usb interface driver for the device.
Fixes: aa4f2b3e41 ("r8152: Choose our USB config with choose_configuration() rather than probe()")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20240308075206.33553-436-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make use of the existing linkmode helpers for converting PHY EEE
register values into links modes, now that ethtool_keee uses link
modes, rather than u32 values.
Rework determining if EEE is active to make is similar as to how
phylib decides, and make use of a phylib helper to validate if EEE is
valid in for the current link mode. This then requires that PHYLIB is
selected.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in preparation of using the existing names for linkmode
bitmaps.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASUS USB-C2500 is an RTL8156 based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Kelly Kane <kelly@hawknetworks.com>
Link: https://lore.kernel.org/r/20231203011712.6314-1-kelly@hawknetworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If you deauthorize the r8152 device (by writing 0 to the "authorized"
field in sysfs) and then reauthorize it (by writing a 1) then it no
longer works. This is because when you do the above we lose the
special configuration that we set in rtl8152_cfgselector_probe().
Deauthorizing causes the config to be set to -1 and then reauthorizing
runs the default logic for choosing the best config.
I made an attempt to fix it so that the config is kept across
deauthorizing / reauthorizing [1] but it was a bit ugly.
Let's instead use the new USB core feature to override
choose_configuration().
This patch relies upon the patches ("usb: core: Don't force USB
generic_subclass drivers to define probe()") and ("usb: core: Allow
subclassed USB drivers to override usb_choose_configuration()")
[1] https://lore.kernel.org/r/20231130154337.1.Ie00e07f07f87149c9ce0b27ae4e26991d307e14b@changeid
Fixes: ec51fbd1b8 ("r8152: add USB device driver for config selection")
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Link: https://lore.kernel.org/r/20231201102946.v2.3.Ie00e07f07f87149c9ce0b27ae4e26991d307e14b@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_aldps_en().
Fixes: 4214cc550b ("r8152: check if disabling ALDPS is finished")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_pre_firmware_1().
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in
r8156b_wait_loading_flash().
Fixes: 195aae321c ("r8152: support new chips")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commits added checks for RTL8152_INACCESSIBLE in the loops in
the driver. There are still a few more that keep tripping the driver
up in error cases and make things take longer than they should. Add
those in.
All the loops that are part of this commit existed in some form or
another since the r8152 driver was first introduced, though
RTL8152_INACCESSIBLE was known as RTL8152_UNPLUG before commit
715f67f33a ("r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE")
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit d9962b0d42 ("r8152: Block future register access if
register access fails") there is a race condition that can happen
between the USB device reset thread and napi_enable() (not) getting
called during rtl8152_open(). Specifically:
* While rtl8152_open() is running we get a register access error
that's _not_ -ENODEV and queue up a USB reset.
* rtl8152_open() exits before calling napi_enable() due to any reason
(including usb_submit_urb() returning an error).
In that case:
* Since the USB reset is perform in a separate thread asynchronously,
it can run at anytime USB device lock is not held - even before
rtl8152_open() has exited with an error and caused __dev_open() to
clear the __LINK_STATE_START bit.
* The rtl8152_pre_reset() will notice that the netif_running() returns
true (since __LINK_STATE_START wasn't cleared) so it won't exit
early.
* rtl8152_pre_reset() will then hang in napi_disable() because
napi_enable() was never called.
We can fix the race by making sure that the r8152 reset routines don't
run at the same time as we're opening the device. Specifically we need
the reset routines in their entirety rely on the return value of
netif_running(). The only way to reliably depend on that is for them
to hold the rntl_lock() mutex for the duration of reset.
Grabbing the rntl_lock() mutex for the duration of reset seems like a
long time, but reset is not expected to be common and the rtnl_lock()
mutex is already held for long durations since the core grabs it
around the open/close calls.
Fixes: d9962b0d42 ("r8152: Block future register access if register access fails")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the functions to read/write registers can fail, most of
the places in the r8152 driver that read/write register values don't
check error codes. The lack of error code checking is problematic in
at least two ways.
The first problem is that the r8152 driver often uses code patterns
similar to this:
x = read_register()
x = x | SOME_BIT;
write_register(x);
...with the above pattern, if the read_register() fails and returns
garbage then we'll end up trying to write modified garbage back to the
Realtek adapter. If the write_register() succeeds that's bad. Note
that as of commit f53a7ad189 ("r8152: Set memory to all 0xFFs on
failed reg reads") the "garbage" returned by read_register() will at
least be consistent garbage, but it is still garbage.
It turns out that this problem is very serious. Writing garbage to
some of the hardware registers on the Ethernet adapter can put the
adapter in such a bad state that it needs to be power cycled (fully
unplugged and plugged in again) before it can enumerate again.
The second problem is that the r8152 driver generally has functions
that are long sequences of register writes. Assuming everything will
be OK if a random register write fails in the middle isn't a great
assumption.
One might wonder if the above two problems are real. You could ask if
we would really have a successful write after a failed read. It turns
out that the answer appears to be "yes, this can happen". In fact,
we've seen at least two distinct failure modes where this happens.
On a sc7180-trogdor Chromebook if you drop into kdb for a while and
then resume, you can see:
1. We get a "Tx timeout"
2. The "Tx timeout" queues up a USB reset.
3. In rtl8152_pre_reset() we try to reinit the hardware.
4. The first several (2-9) register accesses fail with a timeout, then
things recover.
The above test case was actually fixed by the patch ("r8152: Increase
USB control msg timeout to 5000ms as per spec") but at least shows
that we really can see successful calls after failed ones.
On a different (AMD) based Chromebook with a particular adapter, we
found that during reboot tests we'd also sometimes get a transitory
failure. In this case we saw -EPIPE being returned sometimes. Retrying
worked, but retrying is not always safe for all register accesses
since reading/writing some registers might have side effects (like
registers that clear on read).
Let's fully lock out all register access if a register access fails.
When we do this, we'll try to queue up a USB reset and try to unlock
register access after the reset. This is slightly tricker than it
sounds since the r8152 driver has an optimized reset sequence that
only works reliably after probe happens. In order to handle this, we
avoid the optimized reset if probe didn't finish. Instead, we simply
retry the probe routine in this case.
When locking out access, we'll use the existing infrastructure that
the driver was using when it detected we were unplugged. This keeps us
from getting stuck in delay loops in some parts of the driver.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever the RTL8152_UNPLUG is set that just tells the driver that all
accesses will fail and we should just immediately bail. A future patch
will use this same concept at a time when the driver hasn't actually
been unplugged but is about to be reset. Rename the flag in
preparation for the future patch.
This is a no-op change and just a search and replace.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the adapter is unplugged while we're looping in r8153b_ups_en() /
r8153c_ups_en() we could end up looping for 10 seconds (20 ms * 500
loops). Add code similar to what's done in other places in the driver
to check for unplug and bail.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the adapter is unplugged while we're looping in
rtl_phy_patch_request() we could end up looping for 10 seconds (2 ms *
5000 loops). Add code similar to what's done in other places in the
driver to check for unplug and bail.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error handling in rtl8152_probe() is missing a call to release
firmware. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error handling in rtl8152_probe() is missing a call to cancel the
hw_phy_work. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: a028a9e003 ("r8152: move the settings of PHY to a work queue")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtl8152_probe() function lacks a call to the chip-specific
unload() routine when it sees an error in probe. Add it in to match
the cleanup code in rtl8152_disconnect().
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the comment next to USB_CTRL_GET_TIMEOUT and
USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is
usually quite fast, the spec allows them to take up to 5 seconds.
Let's increase the timeout in the Realtek driver from 500ms to 5000ms
(using the #defines) to account for this.
This is not just a theoretical change. The need for the longer timeout
was seen in testing. Specifically, if you drop a sc7180-trogdor based
Chromebook into the kdb debugger and then "go" again after sitting in
the debugger for a while, the next USB control message takes a long
time. Out of ~40 tests the slowest USB control message was 4.5
seconds.
While dropping into kdb is not exactly an end-user scenario, the above
is similar to what could happen due to an temporary interrupt storm,
what could happen if there was a host controller (HW or SW) issue, or
what could happen if the Realtek device got into a confused state and
needed time to recover.
This change is fairly critical since the r8152 driver in Linux doesn't
expect register reads/writes (which are backed by USB control
messages) to fail.
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bulk transfer of the USB may contain many packets. And, the total
number of the packets in the bulk transfer may be more than budget.
Originally, only budget packets would be handled by napi_gro_receive(),
and the other packets would be queued in the driver for next schedule.
This patch would break the loop about getting next bulk transfer, when
the budget is exhausted. That is, only the current bulk transfer would
be handled, and the other bulk transfers would be queued for next
schedule. Besides, the packets which are more than the budget in the
current bulk trasnfer would be still queued in the driver, as the
original method.
In addition, a bulk transfer wouldn't contain more than 400 packets, so
the check of queue length is unnecessary. Therefore, I replace it with
WARN_ON_ONCE().
Fixes: cf74eb5a5b ("eth: r8152: try to use a normal budget")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230926111714.9448-433-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the document of napi, there is no rx process when the
budget is 0. Therefore, r8152_poll() has to return 0 directly when the
budget is equal to 0.
Fixes: d2187f8e44 ("r8152: divide the tx and rx bottom functions")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The D-Link DUB-E250 is an RTL8156 based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Antonio Napolitano <anton@polit.no>
Link: https://lore.kernel.org/r/CV200KJEEUPC.WPKAHXCQJ05I@mercurius
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mario reports that loading r8152 on his system leads to a:
netif_napi_add_weight() called with weight 256
warning getting printed. We don't have any solid data
on why such high budget was chosen, and it may cause
stalls in processing other softirqs and rt threads.
So try to switch back to the default (64) weight.
If this slows down someone's system we should investigate
which part of stopping starting the NAPI poll in this
driver are expensive.
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/all/0bfd445a-81f7-f702-08b0-bd5a72095e49@amd.com/
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230814153521.2697982-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PLA_BP_0 ~ PLA_BP_15 (0xfc28 ~ 0xfc46) are continuous registers, so we
could combine the control transfers into one control transfer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230726030808.9093-419-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reduce the control transfer if all bytes of first or the last DWORD are
written.
The original method is to split the control transfer into three parts
(the first DWORD, middle continuous data, and the last DWORD). However,
they could be combined if whole bytes of the first DWORD or last DWORD
are written. That is, the first DWORD or the last DWORD could be combined
with the middle continuous data, if the byte_en is 0xff.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230726030808.9093-418-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move declarations into include/net/gso.h and code into net/core/gso.c
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stanislav Fomichev <sdf@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230608191738.3947077-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set supports_autosuspend = 1 for the rtl8152_cfgselector_driver.
Fixes: ec51fbd1b8 ("r8152: add USB device driver for config selection")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setting r8153b_rx_agg_chg_indicate() for 2.5G devices. The
r8153b_rx_agg_chg_indicate() has to be called after enabling tx/rx.
Otherwise, the coalescing settings are useless.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the poor throughput for 2.5G devices, when changing the speed from
auto mode to force mode. This patch is used to notify the MAC when the
mode is changed.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The feature of flow control becomes abnormal, if the device sends a
pause frame and the tx/rx is disabled before sending a release frame. It
causes the lost of packets.
Set PLA_RX_FIFO_FULL and PLA_RX_FIFO_EMPTY to zeros before disabling the
tx/rx. And, toggle FC_PATCH_TASK before enabling tx/rx to reset the flow
control patch and timer. Then, the hardware could clear the state and
the flow control becomes normal after enabling tx/rx.
Besides, remove inline for fc_pause_on_auto() and fc_pause_off_auto().
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When memory is a little tight on my system, it's pretty easy to see
warnings that look like this.
ksoftirqd/0: page allocation failure: order:3, mode:0x40a20(GFP_ATOMIC|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0
...
Call trace:
dump_backtrace+0x0/0x1e8
show_stack+0x20/0x2c
dump_stack_lvl+0x60/0x78
dump_stack+0x18/0x38
warn_alloc+0x104/0x174
__alloc_pages+0x588/0x67c
alloc_rx_agg+0xa0/0x190 [r8152 ...]
r8152_poll+0x270/0x760 [r8152 ...]
__napi_poll+0x44/0x1ec
net_rx_action+0x100/0x300
__do_softirq+0xec/0x38c
run_ksoftirqd+0x38/0xec
smpboot_thread_fn+0xb8/0x248
kthread+0x134/0x154
ret_from_fork+0x10/0x20
On a fragmented system it's normal that order 3 allocations will
sometimes fail, especially atomic ones. The driver handles these
failures fine and the WARN just creates spam in the logs for this
case. The __GFP_NOWARN flag is exactly for this situation, so add it
to the allocation.
NOTE: my testing is on a 5.15 system, but there should be no reason
that this would be fundamentally different on a mainline kernel.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230406171411.1.I84dbef45786af440fd269b71e9436a96a8e7a152@changeid
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reduce the control transfer by moving calling rtl8152_get_version() in
rtl8152_probe(). This could prevent from calling rtl8152_get_version()
for unnecessary situations. For example, after setting config #2 for the
device, there are two interfaces and rtl8152_probe() may be called
twice. However, we don't need to call rtl8152_get_version() for this
situation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit ec51fbd1b8 ("r8152: add USB device driver for
config selection"), the code about changing USB configuration
in rtl_vendor_mode() wouldn't be run anymore. Therefore, the
function could be removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rtl8152_cfgselector_probe() should set the USB configuration to the
vendor mode only for the devices which the driver (r8152) supports.
Otherwise, no driver would be used for such devices.
Fixes: ec51fbd1b8 ("r8152: add USB device driver for config selection")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Microsoft Devkit 2023 is a an ARM64 based machine featuring a
Realtek 8153 USB3.0-to-GBit Ethernet adapter. As in their other
machines, Microsoft uses a custom USB device ID.
Add the respective ID values to the driver. This makes Ethernet work on
the MS Devkit device. The chip has been visually confirmed to be a
RTL8153.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20230111133228.190801-1-andre.przywara@arm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Subclassing the generic USB device driver to override the
default configuration selection regardless of matching interface
drivers.
The r815x family devices expose a vendor specific function which
the r8152 interface driver wants to handle. This is the preferred
device mode. Additionally one or more USB class functions are
usually supported for hosts lacking a vendor specific driver. The
choice is USB configuration based, with one alternate function per
configuration.
Example device with both NCM and ECM alternate cfgs:
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 3
P: Vendor=0bda ProdID=8156 Rev=31.00
S: Manufacturer=Realtek
S: Product=USB 10/100/1G/2.5G LAN
S: SerialNumber=001000001
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=256mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=00 Driver=r8152
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 2 Ivl=128ms
C: #Ifs= 2 Cfg#= 2 Atr=a0 MxPwr=256mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0d Prot=00 Driver=
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=128ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=01 Driver=
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
C: #Ifs= 2 Cfg#= 3 Atr=a0 MxPwr=256mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=128ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
A problem with this is that Linux will prefer class functions over
vendor specific functions. Using the above example, Linux defaults
to cfg #2, running the device in a sub-optimal NCM mode.
Previously we've attempted to work around the problem by
blacklisting the devices in the ECM class driver "cdc_ether", and
matching on the ECM class function in the vendor specific interface
driver. The latter has been used to switch back to the vendor
specific configuration when the driver is probed for a class
function.
This workaround has several issues;
- class driver blacklists is additional maintanence cruft in an
unrelated driver
- class driver blacklists prevents users from optionally running
the devices in class mode
- each device needs double match entries in the vendor driver
- the initial probing as a class function slows down device
discovery
Now these issues have become even worse with the introduction of
firmware supporting both NCM and ECM, where NCM ends up as the
default mode in Linux. To use the same workaround, we now have
to blacklist the devices in to two different class drivers and
add yet another match entry to the vendor specific driver.
This patch implements an alternative workaround strategy -
independent of the interface drivers. It avoids adding a
blacklist to the cdc_ncm driver and will let us remove the
existing blacklist from the cdc_ether driver.
As an additional bonus, removing the blacklists allow users to
select one of the other device modes if wanted.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Lenovo USB-C Travel Hub supports MAC passthrough.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
