In transmit path, it is likely that the iova is not aligned to PCIe TLP
max payload size, which is 128 for WCN7850. Normally in such cases hardware
is expected to split the packet into several parts in a manner such that
they, other than the first one, have aligned iova. However due to hardware
limitations, WCN7850 does not behave like that properly with some specific
unaligned iova in transmit path. This easily results in target hang in a
KPI transmit test: packet send/receive failure, WMI command send timeout
etc. Also fatal error seen in PCIe level:
...
Capabilities: ...
...
DevSta: ... FatalErr+ ...
...
...
Work around this by manually moving/reallocating payload buffer such that
we can map it to a 128 bytes aligned iova. The moving requires sufficient
head room or tail room in skb: for the former we can do ourselves a favor
by asking some extra bytes when registering with mac80211, while for the
latter we can do nothing.
Moving/reallocating buffer consumes additional CPU cycles, but the good news
is that an aligned iova increases PCIe efficiency. In my tests on some X86
platforms the KPI results are almost consistent.
Since this is seen only with WCN7850, add a new hardware parameter to
differentiate from others.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Cc: <stable@vger.kernel.org>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240715023814.20242-1-quic_bqiang@quicinc.com
Currently, the Rx data path only supports parsing peer metadata of version
zero. However, the QCN9274 platform configures the peer metadata version
as V1B. When V1B peer metadata is parsed using the version zero logic,
invalid data is populated, causing valid packets to be dropped. To address
this issue, refactor the peer metadata version and add the version based
parsing to populate the data from peer metadata correctly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: 2870338109 ("wifi: ath12k: add support for peer meta data version")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240624145418.2043461-1-quic_periyasa@quicinc.com
Advertise the driver support for multiple BSSID (MBSSID) and
enhanced multi-BSSID advertisements (EMA) by setting extended
capabilities.
Configure mbssid_max_interfaces and ema_max_profile_periodicity
fields in structure wiphy which are used to advertise maximum number
of interfaces and profile periodicity supported by the driver.
Add new WMI fields to configure maximum vdev count supported for
MBSSID and profile periodicity in case of EMA.
Set WMI_RSRC_CFG_FLAGS2_CALC_NEXT_DTIM_COUNT_SET flag to allow
firmware to track and update the DTIM counts for each nontransmitted
profile.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-2-quic_alokad@quicinc.com
Parse SMPS configuration from IEs and configure. Without this,
SMPS is not enabled for 6 GHz band. This is disabled for
WCN7850 as hardware does not support it.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508173655.22191-7-quic_pradeepc@quicinc.com
Currently, ath12k does not support Time-Average-SAR (TAS). In order to enable
TAS read the tables from ACPI and send them to the firmware using
WMI_PDEV_SET_BIOS_INTERFACE_CMDID command. Besides, ath12k registers an ACPI
event callback so that ACPI can notify ath12k to get the updated SAR power
table and sends it to the firmware when the device state is changed.
ACPI is only enabled for WCN7850 using struct ath12k_hw_params::acpi_guid
field. Most likely QCN9274 will never support ACPI as the chip is not used in
laptops.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-2-quic_lingbok@quicinc.com
With single wiphy, multiple radios are combined into a single wiphy.
Since any channel can be assigned to a vif being brought up,
the vdev cannot be created during add_interface(). Hence defer the
vdev creation till channel assignment.
If only one radio is part of the wiphy, then the existing logic
is maintained, i.e vdevs are created during add interface and
started during channel assignment. This ensures no functional changes
to single pdev devices which has only one radio in the SoC.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-5-quic_ramess@quicinc.com
To reduce power consumption enable 802.11 power save mode in
station mode. This allows both radio and CPU to sleep more.
Only enable the mode on WCN7850, other chips don't support it
for now.
To test that power save mode is running, run below command and
check there is no NULL Data frame seen by a sniffer:
iw dev <inf> set power_save off
And run below command, then check there is a NULL Data frame
in sniffer:
iw dev <inf> set power_save on
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240201035830.2534-1-quic_bqiang@quicinc.com
QCN9274 can support single-PHY or split-PHY architecture. Currently,
only the single-PHY architecture is supported in ath12k.
The split-PHY QCN9274 requires different AMSS firmware binary
"amss_dualmac.bin".
Hence, add support to read board id from OTP. Based on board id
decide whether single-mac / dual-mac firmware needs to be downloaded
to the target. Also, update HW param max_radios to support split-PHY
in QCN9274.
Also, add new Firmware IE for firmware_N.bin
"ATH11K_FW_IE_AMSS_DUALMAC_IMAGE" to support dualmac QCN9274.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Ganesh Babu Jothiram <quic_gjothira@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-13-quic_rajkbhag@quicinc.com
With word mask subscription support, the rx_desc structure will
change. The fields in this structure rx_desc will be reduced to only
the required fields. To make word mask subscription changes compatible
with the older firmware version (firmware that does not support word
mask subscription), two different structures of rx_desc will be
required for the same hardware.
The hardware param hal_desc_sz value cannot be constant for the same
hardware. It depends on the size of rx_desc structure which may
change based on firmware capability to support word mask subscription.
Hence, remove hal_desc_sz from hardware param and add hal_rx_ops
to get the size of rx_desc in run time.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-9-quic_rajkbhag@quicinc.com
In segment memory mode, firmware allocates memory segments of size
2 MB. This 2 MB memory is used by firmware for the number of peers.
This number of peer is sent from host to firmware during WMI init
command. For single-phy the number of peers sent is
TARGET_NUM_PEERS_SINGLE = 529 (512 + 17). While for split-phy number
of peers sent to firmware is TARGET_NUM_PEERS_DBS = 2 *(512 + 17) =
1058. With this 1058 number of peers firmware is unable to allocate
memory in 2 MB segment and firmware crash is observed.
Hence, fix this firmware crash by reducing the number of stations
TARGET_NUM_STATIONS for split-phy.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-7-quic_rajkbhag@quicinc.com
Add support to process WMI_TLV_SERVICE_PEER_METADATA_V1A_V1B_SUPPORT
service bit. If this service bit is set by firmware, then it expects
host to set rx_peer_meta_data_ver in wmi_resource_config's flags2
with value 3 for QCN9274 to indicate as V1B meta version. If this is
not set firmware crash is seen during peer addition.
Hence, if WMI_TLV_SERVICE_PEER_METADATA_V1A_V1B_SUPPORT service bit
is set by firmware, set correct peer metadata version to avoid
firmware crash.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-4-quic_rajkbhag@quicinc.com
Currently, QMI MLO host capability parameters are specific to the WCN7850
platform. To make use of this helper function across all the platforms,
move the platform specific MLO capability parameter to the HW param
configuration.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240113001659.1022465-2-quic_periyasa@quicinc.com
Currently ATH12K_BD_IE_BOARD_EXT is not used, so remove it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231216060140.30611-4-quic_bqiang@quicinc.com
RDDM is Ram Dump Debug Module which is used to debug issues when the
firmware encounters an error. The rddm_size is needed by the firmware
while MHI goes to the RDDM state. Provide the size to MHI subsystem so
that the firmware restart works when the firmware crashes.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230721055305.20420-2-quic_wgong@quicinc.com
When hardware rfkill is enabled in the firmware, it will report the
capability using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY event
to the host. Currently ath12k does not process this service capability. In
order to support this, update ath12k to check if the capability is enabled,
if so, send the GPIO information to firmware. When the firmware detects
hardware rfkill is enabled by the user, it will report it using
WMI_RFKILL_STATE_CHANGE_EVENTID. When ath12k receive the event, it will set
the value of rfkill_radio_on based on whether radio_state is equal to
WMI_RFKILL_RADIO_STATE_ON, then send WMI_PDEV_PARAM_RFKILL_ENABLE to
firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906110412.182176-1-quic_lingbok@quicinc.com
Currently the CNSS (Connectivity Subsystem) QMI feature is assigned to
qmi_wlanfw_host_cap_req_msg_v01 request directly, this prevents chip-specific
CNSS features from being added easily.
Solve this by adding a new field qmi_cnss_feature_bitmap to hw_params so
chip-specific CNSS features can be assigned to this field and later assigned to
qmi_wlanfw_host_cap_req_msg_v01 request.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230404032057.3236122-2-quic_cjhuang@quicinc.com
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.
ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.
ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.
Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.
The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.
The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:
https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52
The driver has had multiple authors who are listed in alphabetical
order below.
Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
