In transmit path, it is likely that the iova is not aligned to PCIe TLP
max payload size, which is 128 for WCN7850. Normally in such cases hardware
is expected to split the packet into several parts in a manner such that
they, other than the first one, have aligned iova. However due to hardware
limitations, WCN7850 does not behave like that properly with some specific
unaligned iova in transmit path. This easily results in target hang in a
KPI transmit test: packet send/receive failure, WMI command send timeout
etc. Also fatal error seen in PCIe level:
...
Capabilities: ...
...
DevSta: ... FatalErr+ ...
...
...
Work around this by manually moving/reallocating payload buffer such that
we can map it to a 128 bytes aligned iova. The moving requires sufficient
head room or tail room in skb: for the former we can do ourselves a favor
by asking some extra bytes when registering with mac80211, while for the
latter we can do nothing.
Moving/reallocating buffer consumes additional CPU cycles, but the good news
is that an aligned iova increases PCIe efficiency. In my tests on some X86
platforms the KPI results are almost consistent.
Since this is seen only with WCN7850, add a new hardware parameter to
differentiate from others.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Cc: <stable@vger.kernel.org>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240715023814.20242-1-quic_bqiang@quicinc.com
We have moved to a new group-managed repo, and this is the first pull
request from that repo, and from me. Fingers crossed...
We have some new features in ath12k along with some cleanups in ath11k
and ath12k. Also notable are some device-tree changes to allow certain
ath11k and ath12k devices to work with a new power sequencing
subsystem.
Major changes:
ath12k
* DebugFS support for datapath statistics
* WCN7850: support for WoW (Wake on WLAN)
* WCN7850: device-tree bindings
ath11k
* QCA6390: device-tree bindings
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQQ/mtSHzPUi16IfDEksFbugiYzLewUCZoQU7hQcampvaG5zb25A
a2VybmVsLm9yZwAKCRAsFbugiYzLe6vCAP9mt6rfI2SWucd0ex9XbXwVkN7vV5Qn
NCvRXeT5QlnfFQEAt0DBUnmU/CuShroshEw2kXKLHJpZ1y6Oz6YVN49ECAU=
=ArqZ
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20240702' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
ath.git patches for v6.11
We have moved to a new group-managed repo, and this is the first pull
request from that repo, and from me. Fingers crossed...
We have some new features in ath12k along with some cleanups in ath11k
and ath12k. Also notable are some device-tree changes to allow certain
ath11k and ath12k devices to work with a new power sequencing
subsystem.
Major changes:
ath12k
* DebugFS support for datapath statistics
* WCN7850: support for WoW (Wake on WLAN)
* WCN7850: device-tree bindings
ath11k
* QCA6390: device-tree bindings
Pdev id from mac phy capabilities will be sent as a part of
HTT/WMI command to firmware. This causes issue with single pdev
devices where firmware does not respond to the WMI/HTT request
sent from host.
For single pdev devices firmware expects pdev id as 1 for 5 GHz/6 GHz
phy and 2 for 2 GHz band. Add wrapper ath12k_mac_get_target_pdev_id()
to help fetch right pdev for single pdev devices.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240621102809.3984004-1-quic_rgnanase@quicinc.com
With WoWLAN enabled and after sleeping for a rather long time,
we are seeing that with some APs, it is not able to wake up
the STA though the correct wake up pattern has been configured.
This is because the host doesn't send keepalive command to
firmware, thus firmware will not send any packet to the AP and
after a specific time the AP kicks out the STA.
So enable keepalive before going to suspend and disable it after
resume back.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-9-quic_bqiang@quicinc.com
Host sets GTK related info to firmware before WoW is enabled, and
gets rekey replay_count and then disables GTK rekey when WoW quits.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-8-quic_bqiang@quicinc.com
Support ARP and NS offload in WoW state.
Tested this way: put machine A with QCA6390 to WoW state,
ping/ping6 machine A from another machine B, check sniffer to see
any ARP response and Neighbor Advertisement from machine A.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-7-quic_bqiang@quicinc.com
Implement net-detect feature by setting flag
WIPHY_WOWLAN_NET_DETECT if firmware supports this
feature. Driver sets the related PNO configuration
to firmware before entering WoW and firmware then
scans periodically and wakes up host if a specific
SSID is found.
Note that firmware crashes if we enable it for both
P2P vdev and station vdev simultaneously because
firmware can only support one vdev at a time. Since
there is rare scenario for a P2P vdev to do net-detect,
skip it for P2P vdevs.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-5-quic_bqiang@quicinc.com
Implement basic WoW functionalities such as magic-packet, disconnect
and pattern. The logic is very similar to ath11k.
When WoW is configured, ath12k_core_suspend and ath12k_core_resume
are skipped (by checking ar->state) as we are not allowed to power
cycle firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-4-quic_bqiang@quicinc.com
The Current method for advertising the maximum MBSSID interface count
assumes single radio per wiphy (multi wiphy model). However, this
assumption is incorrect for multi radio per wiphy (single wiphy model).
Therefore, populate the parameter for each radio present in the MAC
abstraction layer (ah). This approach ensure scalability for both single
wiphy and multi wiphy models.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: 519a545cfe ("wifi: ath12k: advertise driver capabilities for MBSSID and EMA")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240613153813.3509837-1-quic_periyasa@quicinc.com
Currently, if the access point receives an association
request containing an Extended HE Capabilities Information
Element with an invalid MCS-NSS, it triggers a firmware
crash.
This issue arises when EHT-PHY capabilities shows support
for a bandwidth and MCS-NSS set for that particular
bandwidth is filled by zeros and due to this, driver obtains
peer_nss as 0 and sending this value to firmware causes
crash.
Address this issue by implementing a validation step for
the peer_nss value before passing it to the firmware. If
the value is greater than zero, proceed with forwarding
it to the firmware. However, if the value is invalid,
reject the association request to prevent potential
firmware crashes.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ajith C <quic_ajithc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240613053528.2541645-1-quic_ajithc@quicinc.com
Currently SMPS configuration failed when the Information
Elements (IEs) did not contain HT or 6 GHz capabilities. This
caused legacy peer association to fail as legacy peers do not
have HT or 6 GHz capabilities. Fix this by not returning an
error when SMPS configuration fails due to the absence of HT
or 6 GHz capabilities.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: f0e61dc7ec ("wifi: ath12k: refactor SMPS configuration")
Reported-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Reported-by: Zachary Smith <dr.z.smith@gmail.com>
Closes: https://lore.kernel.org/all/CAM=znoFPcXrn5GhDmDmo50Syic3-hXpWvD+vkv8KX5o_ZTo8kQ@mail.gmail.com/
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Reported-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240612225336.2303119-1-quic_pradeepc@quicinc.com
Smatch throws following errors
drivers/net/wireless/ath/ath12k/mac.c:1922 ath12k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
drivers/net/wireless/ath/ath12k/mac.c:1922 ath12k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_160'.
drivers/net/wireless/ath/ath12k/mac.c:1924 ath12k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
In ath12k_peer_assoc_h_he() rx_mcs_80 and rx_mcs_160 variables
remain uninitialized in the following conditions:
1. Whenever the value of mcs_80 become equal to
IEEE80211_HE_MCS_NOT_SUPPORTED then rx_mcs_80 remains uninitialized.
2. Whenever phy capability is not supported 160 channel width and
value of mcs_160 become equal to IEEE80211_HE_MCS_NOT_SUPPORTED
then rx_mcs_160 remains uninitialized.
Initialize these variables during declaration.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240611031017.297927-3-quic_aarasahu@quicinc.com
Smatch throws below error
drivers/net/wireless/ath/ath12k/mac.c:8318 ath12k_mac_op_get_survey() error: we previously assumed 'sband' could be null
Currently, we access sband inside the null check of the sband
in ath12k_mac_op_get_survey().
Fix this issue by removing the entire if block, because decrement
idx is unnecessary since there are no more band to test.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: 70e3be54bb ("wifi: ath12k: fix survey dump collection in 6 GHz")
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240611031017.297927-2-quic_aarasahu@quicinc.com
Currently, device (ab) reference in hardware abstraction (ah)
is not used anywhere. Also, with multiple device group abstraction,
hardware abstraction would be coupled with device group abstraction
rather than single device.
Hence, remove the ab reference from hardware abstraction.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529060939.4156281-1-quic_hprem@quicinc.com
Whenever firmware is crashed in split-phy below WARN_ON() triggered:
WARNING: CPU: 3 PID: 82 at net/mac80211/driver-ops.c:41 drv_stop+0xac/0xbc
Modules linked in: ath12k qmi_helpers
CPU: 3 PID: 82 Comm: kworker/3:2 Tainted: G D W 6.9.0-next-20240520-00113-gd981a3784e15 #39
Hardware name: Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C9 (DT)
Workqueue: events_freezable ieee80211_restart_work
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : drv_stop+0xac/0xbc
lr : ieee80211_stop_device+0x54/0x64
sp : ffff8000848dbb20
x29: ffff8000848dbb20 x28: 0000000000000790 x27: ffff000014d78900
x26: ffff000014d791f8 x25: ffff000007f0d9b0 x24: 0000000000000018
x23: 0000000000000001 x22: 0000000000000000 x21: ffff000014d78e10
x20: ffff800081dc0000 x19: ffff000014d78900 x18: ffffffffffffffff
x17: ffff7fffbca84000 x16: ffff800083fe0000 x15: ffff800081dc0b48
x14: 0000000000000076 x13: 0000000000000076 x12: 0000000000000001
x11: 0000000000000000 x10: 0000000000000a60 x9 : ffff8000848db980
x8 : ffff000000dddfc0 x7 : 0000000000000400 x6 : ffff800083b012d8
x5 : ffff800083b012d8 x4 : 0000000000000000 x3 : ffff000014d78398
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000014d78900
Call trace:
drv_stop+0xac/0xbc
ieee80211_stop_device+0x54/0x64
ieee80211_do_stop+0x5a0/0x790
ieee80211_stop+0x4c/0x178
__dev_close_many+0xb0/0x150
dev_close_many+0x88/0x130
dev_close.part.171+0x44/0x74
dev_close+0x1c/0x28
cfg80211_shutdown_all_interfaces+0x44/0xfc
ieee80211_restart_work+0xfc/0x14c
process_scheduled_works+0x18c/0x2dc
worker_thread+0x13c/0x314
kthread+0x118/0x124
ret_from_fork+0x10/0x20
---[ end trace 0000000000000000 ]---
The warning in question is from drv_stop():
if (WARN_ON(!local->started))
return;
The sequence of WARN_ON() is:
Thread 1:
-Firmware crash calls ath12k_core_reset().
-Call ieee80211_restart_hw() inside
ath12k_core_post_reconfigure_recovery() which schedules worker
for both hardware.
-Wait for completion of ab->recovery_start.
Thread 2 (worker thread):
-One hardware acquires rtnl_lock() inside ieee80211_restart_hw() and
calls ath12k_mac_wait_reconfigure() into ath12k_mac_op_start().
-Hardware is waiting for ab->reconfigure_complete but at this time
recovery_start_count value is 1 because another worker thread
(local->restart_work) is still waiting for rtnl_lock().
recovery_start_count is not equal to number of radios
(2 in split-phy). So ab->recovery_start complete does not set
due to this, thread 1 is still waiting and not able to perform
hif power down up and firmware reload.
-Wait timeout happens for ab->reconfigure_complete and comeback
to caller (ath12k_mac_op_start()) and sends WMI command to
crashed firmware and gets error.
-This returns error to drv_start() and local->started is set to false.
-Hardware calls cfg80211_shutdown_all_interfaces() after receiving error
inside ieee80211_restart_work() and goes to drv_stop(), here we trigger
WARN_ON as local->started is false.
To fix this issue call ieee80211_restart_hw() after firmware has been
reloaded. Now, each hardware can send WMI command to firmware
successfully. With this fix we don't need to wait for
ab->recovery_start completion so remove
ath12k_mac_wait_reconfigure().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 HW2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529034405.2863150-1-quic_aarasahu@quicinc.com
During normal de-initialization path or if any error happens while
registering the hardware, there is no support to unregister the per pdev
debugfs. Add support for the same.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529043043.2488031-3-quic_adisi@quicinc.com
Function ath12k_debugfs_register() is called once inside the function
ath12k_mac_hw_register(). However, with single wiphy model, there could
be multiple pdevs registered under single hardware. Hence, need to register
debugfs for each one of them.
Move the caller inside the loop which iterates over all underlying pdevs.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: f8bde02a26 ("wifi: ath12k: initial debugfs support")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529043043.2488031-2-quic_adisi@quicinc.com
When multiple radios are advertised as a single wiphy which supports various
bands, vdev creation for the vif is deferred until channel is assigned to it.
If a remain on channel (RoC) request is received from mac80211, select the
corresponding radio (ar) based on channel and create a vdev on that radio to
initiate an RoC scan.
Note that on RoC completion this vdev is not deleted. If a new RoC/hw scan
request is seen on that same vif for a different band the vdev will be deleted
and created on the new radio supporting the request.
Also if the RoC scan is requested when the vdev is in started state, no
switching to new radio is allowed and RoC request can be accepted only on
channels within same radio.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240528082739.1226758-1-quic_ramess@quicinc.com
Currently, hw_link_id is sent in WMI service ready event but it
is not parsed anywhere.
But, in future, for multi-link operation, this parameter would be
needed by many WMI commands such as WMI beacon template
(WMI_BCN_TMPL_CMDID), WMI vdev start for Multi-link virtual AP
interfaces (WMI_VDEV_START_REQUEST_CMDID), WMI peer assoc command
(WMI_PEER_ASSOC_CMDID) for Multi-link peer and so on.
Hence, add changes to parse and store the hw_link_id received in
WMI service ready event in ath12k_pdev structure.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529054955.4105240-1-quic_hprem@quicinc.com
ath12k_mac_op_unassign_vif_chanctx() will do peer delete for WCN7850's monitor
interface. But for host no need to do peer create/delete for monitor interface
because firmware doesn't require it, QCN9274 is the same. Also, the first
judgement is true only for WCN7850, so this logic won't affect QCN9274 at any
time.
So remove this peer delete.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240510111238.1113-1-quic_kangyang@quicinc.com
Remove the unnecessary WMI vdev down operation as firmware
internally does so already as part of WMI vdev restart.
Repeated vdev down results in a firmware crash during channel
switch operation when multiple BSSID advertisements are enabled:
ath12k_pci 0000:06:00.0: firmware crashed: MHI_CB_SYS_ERROR
ath12k_pci 0000:06:00.0: failed to send WMI_VDEV_SET_PARAM_CMDID
ath12k_pci 0000:06:00.0: failed to set vdev 5 HE MU mode: -108 param_value 7b
ath12k_pci 0000:06:00.0: failed to set he mode vdev 5
ath12k_pci 0000:06:00.0: failed to restart vdev 5: -108
ath12k_pci 0000:06:00.0: failed to send WMI_VDEV_SET_PARAM_CMDID
ath12k_pci 0000:06:00.0: failed to set vdev 4 HE MU mode: -108 param_value 7b
ath12k_pci 0000:06:00.0: failed to set he mode vdev 4
ath12k_pci 0000:06:00.0: failed to restart vdev 4: -108
ath12k_pci 0000:06:00.0: failed to send WMI_VDEV_SET_PARAM_CMDID
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-10-quic_alokad@quicinc.com
Add new function ath12k_mac_setup_bcn_tmpl_ema() which retrieves
a list of EMA (Enhanced Multi-BSSID Advertisements) beacon templates
from mac80211 and sends all to firmware. Add support to send EMA
configurations to firmware by adding a new parameter 'ema_params' in
struct wmi_bcn_tmpl_cmd.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-9-quic_alokad@quicinc.com
- A single beacon template is used for one multiple BSSID group as
only one interface from group transmits the beacons. But firmware
requires the host to send this template each time a nontransmitted
interface is brought up. Hence, modify existing logic to retrieve
the template from vif context of the transmitting interface. Also,
firmware crashes if host sends a template for a nontransmitted
interface which is already up, add a check to avoid this.
- Set rsnie_present and wpaie_present fields for nontransmitted VAPs.
- Send offset to the multiple BSSID element in the beacon template
firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-8-quic_alokad@quicinc.com
Configure security parameters in a separate function to make it
easier to support setting the same for nontransmitted profiles.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-7-quic_alokad@quicinc.com
Include MBSSID parameters in WMI vdev up operation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-6-quic_alokad@quicinc.com
Host needs to send multiple BSSID configurations to firmware for
each vdev in ath12k_wmi_vdev_up() for AP mode. This function accepts
individual input parameters hence any new argument will require changes
to all callers. Most of these will use default value (0 or NULL).
Create a structure for the function arguments and include objects with
all members initialized to zero to minimize future changes.
Tested-on : QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-5-quic_alokad@quicinc.com
Configure multiple BSSID flags and vdev_id of the transmited profile
in vdev create/start commands depending on the service bit
WMI_TLV_SERVICE_MBSS_PARAM_IN_VDEV_START_SUPPORT.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-3-quic_alokad@quicinc.com
Advertise the driver support for multiple BSSID (MBSSID) and
enhanced multi-BSSID advertisements (EMA) by setting extended
capabilities.
Configure mbssid_max_interfaces and ema_max_profile_periodicity
fields in structure wiphy which are used to advertise maximum number
of interfaces and profile periodicity supported by the driver.
Add new WMI fields to configure maximum vdev count supported for
MBSSID and profile periodicity in case of EMA.
Set WMI_RSRC_CFG_FLAGS2_CALC_NEXT_DTIM_COUNT_SET flag to allow
firmware to track and update the DTIM counts for each nontransmitted
profile.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-2-quic_alokad@quicinc.com
Parse SMPS configuration from IEs and configure. Without this,
SMPS is not enabled for 6 GHz band. This is disabled for
WCN7850 as hardware does not support it.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508173655.22191-7-quic_pradeepc@quicinc.com
Move fetching SMPS value to a new function and use u16_get_bits
to extract it from capabilities. This will help in extending the
functionality when SMPS support in 6 GHz band gets added in
subsequent patches.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508173655.22191-6-quic_pradeepc@quicinc.com
Currently A-MPDU aggregation parameters are not being configured
during peer association for 6 GHz band. Hence, extract these
parameters from station's capabilities received in association
request and send to firmware. Without this, A-MPDU aggregation
is not happening in 6 GHz band.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Avula Sri Charan <quic_asrichar@quicinc.com>
Signed-off-by: Avula Sri Charan <quic_asrichar@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508173655.22191-5-quic_pradeepc@quicinc.com
When ath12k receives survey request, choose the 6 GHz band
when enabled. Without this, survey requests do not include
any 6 GHz band results, leading to failures in auto channel
selection.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508173655.22191-4-quic_pradeepc@quicinc.com
Add support for the 6 GHz channel 2 with center frequency
5935 MHz and operating class 136 per IEEE Std 802.11ax-2021,
Table E-4.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508173655.22191-2-quic_pradeepc@quicinc.com
In ath12k_mac_op_assign_vif_chanctx(), there is a logic to
create peer using ar->mac_addr for a STA vdev. This is invalid
because a STA vdev should have a peer created using AP's
MAC address. Besides, if we run into that logic, it means a peer
has already been created earlier, we should not create it again.
So remove it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240429081525.983-6-quic_kangyang@quicinc.com
ath12k_mac_op_unassign_vif_chanctx() will do vdev down in function
ath12k_mac_monitor_stop(). So no need to do vdev down again.
remove the duplicated one.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240429081525.983-4-quic_kangyang@quicinc.com
ath12k_mac_op_unassign_vif_chanctx() will do vdev stop in
ath12k_mac_monitor_stop(). This ath12k_mac_vdev_stop() will do vdev stop
again, then might trigger firmware crash.
So add judgement to avoid duplicated vdev stop.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: c9e4e41e71 ("wifi: ath12k: move peer delete after vdev stop of station for WCN7850")
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240429081525.983-3-quic_kangyang@quicinc.com
monitor_flags is defined in struct ath12k. Although it is changed in
some places, but it is not actually used.
So remove related code.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240429081525.983-2-quic_kangyang@quicinc.com
Currently, hardware state is not protected across the reconfigure
operations. However, in single wiphy models, multiple radio/links is
exposed as a MAC hardware (ieee80211_hw) through the driver hardware
abstraction (ath12k_hw) layer. In such scenario, we need to protect
hardware state across the multiple radio/link at the driver hardware
abstraction (ath12k_hw) layer. Therefore, introduce a new mutex in
the ath12k_hw layer.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425090307.3233434-4-quic_periyasa@quicinc.com
Currently, in multi wiphy models, the mac80211 hardware state is maintained
within the radio/link structure. However, in single wiphy models, the
mac80211 hardware state is needed at the hardware abstraction layer
(ath12k_hw). Therefore, move the hardware state from the radio/link
structure to the hardware abstraction layer (ath12k_hw). Additionally,
update the naming convention of the state enums to enhance clarity and
consistency.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425090307.3233434-3-quic_periyasa@quicinc.com
Currently, in multi-wiphy models, the recovery handler access mac80211
HW from the radio/link structure. This will be incorrect for single wiphy
model, as they will hold multiple link/radio structures. To fix this,
access mac80211 HW based on the number of hardware in the SoC/chip. This
approach makes the recovery handler compatible with both multi wiphy and
single wiphy models.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425090307.3233434-2-quic_periyasa@quicinc.com
Currently, when using WCN7850 or QCN9274 as AP, ath12k always performs down
grade phy mode operation regardless of whether the firmware supports EHT
capability or not and then vdev will start in HE mode. When stations that
support EHT capability try to connect to the AP, the AP will set phy mode
to EHT after receiving the association request packet, and then send
WMI_PEER_ASSOC_CMDID command to firmware, AP’s firmware will crash.
This is because when the ath12k_mac_copy_sband_iftype_data() function
handles EHT capability, it does not copy the EHT capability into the
iftype[band][type] array according to the interface type. So, interface
type should not be used as an index to get eht_cap in
ath12k_mac_check_down_grade_phy_mode() function.
To address this issue, use types_mask to select the eht_cap in
ath12k_mac_check_down_grade_phy_mode() function.
This patch affects QCN9274 and WCN7850 because they have the same issue.
Hostapd log:
wlo1: STA 02:03:7f:37:12:34 IEEE 802.11: Could not set STA to kernel driver
Kernel log:
[270894.816076] ath12k_pci 0000:03:00.0: failed to send WMI_PEER_SET_PARAM cmd
[270894.816111] ath12k_pci 0000:03:00.0: failed to setup peer SMPS for vdev 0: -108
[270894.816122] ath12k_pci 0000:03:00.0: Failed to associate station: 02:03:7f:37:12:34
[270894.843389] ieee80211 phy5: Hardware restart was requested
[270894.843517] ath12k_pci 0000:03:00.0: failed to lookup peer 02:03:7f:37:12:34 on vdev 0
[270894.843616] ath12k_pci 0000:03:00.0: failed to send WMI_PEER_DELETE cmd
[270894.843650] ath12k_pci 0000:03:00.0: failed to delete peer vdev_id 0 addr 02:03:7f:37:12:34 ret -108
[270894.843663] ath12k_pci 0000:03:00.0: Failed to delete peer: 02:03:7f:37:12:34 for VDEV: 0
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425083837.5340-1-quic_lingbok@quicinc.com
When AP goes down or too far away without indication to STA, beacon miss
will be detected. Then for WCN7850's firmware, it will use roam event
to send beacon miss to host.
If STA doesn't handle the beacon miss, will keep the fake connection
and unable to roam.
So add support for WCN7850 to trigger disconnection from AP when
receiving this event from firmware.
It has to be noted that beacon miss event notification for QCN9274
to be handled in a separate patch as it uses STA kickout WMI event
to notify beacon miss and the current STA kickout event is processed
as low_ack.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412094447.2063-1-quic_kangyang@quicinc.com
In order to send out all packets before going to suspend, current code
adds a 500ms delay as a workaround. It is a rough estimate and may not
work.
Fix this by checking packet counters, if counters become zero, then all
packets are sent out or dropped.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-7-quic_bqiang@quicinc.com
Currently, when debug logs are enabled, messages such as the following
are found in the kernel log:
event mgmt rx skb pK-error len 209 ftype 00 stype 50
The "pK-error" comes from using %pK to display an skb address in an
interrupt context.
Per the guidance in the current "printk-formats" documentation, %pK
"is only intended when producing content of a file read by userspace
from e.g. procfs or sysfs, not for dmesg."
So replace %pK with %p in all of the ath12k_dbg() format strings.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240416-pk-v1-1-2c8852743e6d@quicinc.com
ath12k will support Multi-Link Operation (MLO) in the future but not yet. A
major change with MLO is that cfg80211 will disable Wireless Extension (WEXT)
user space interface. To avoid having inconsistent user experience, first
supporting WEXT and later not, disable WEXT already now.
Now ath12k claims that WEXT is not supported:
$ iwconfig wlan0
wlan0 no wireless extensions.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240411165645.4071238-1-kvalo@kernel.org
Every time EHT Operation element changed, mac80211 will parse it and
extract the valid puncturing bitmap according to the bandwidth.
Current driver only update puncturing bitmap to firmware as vdev
parameter. Which can only meet the needs of AP. But STA will also use
it as peer parameter. If only update as vdev parameter, might cause
firmware crash. QCN9274 is the same.
So update bandwidth and puncturing bitmap as peer parameters once they
changed for STA. Then send them to the firmware by WMI event.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240408083047.22548-1-quic_kangyang@quicinc.com
The radio for which the survey info needs to be collected
depends on the channel idx which could be based on the band.
Use the idx to identify the appropriate sband since multiple
bands could be combined for single wiphy case.
Also use the channel idx and sband to identify the corresponding
radio on which the survey results needs to be populated.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-13-quic_ramess@quicinc.com
Since multiple radios are abstracted under a single wiphy,
apply the rts threshold value to all the vdevs of the radios
combined under single wiphy.
This also implies that vif specific rts threshold support
needs to be added in future from cfg80211/mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-12-quic_ramess@quicinc.com
As multiple radios are combined into a single wiphy, and
the current infrastructure supports only set/get antenna
for the wiphy, the max Tx/Rx antenna capability is advertised
during wiphy register.
Hence, When antenna set/get is received we adjust the set/get
based on max radio capability and set/get antenna accordingly.
Multi radio capability needs to introduced with interface
combination changes to support single wiphy model in cfg80211
which would help extend the wiphy specific get/set configs similar
to this to per hw level.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-11-quic_ramess@quicinc.com
