If the platform decides to block enabling the device nothing is printed
currently. This can lead to some confusion since the dmesg output will
usually print an error with no context e.g.
e1000e: probe of 0022:01:00.0 failed with error -22
This shouldn't be spammy since pci_enable_device() already prints a
messages when it succeeds.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200409061337.9187-1-oohall@gmail.com
Fix gcc '-Wunused-but-set-variable' warning:
arch/powerpc/platforms/powernv/pci-ioda.c: In function pnv_ioda_configure_pe:
arch/powerpc/platforms/powernv/pci-ioda.c:867:18: warning: variable parent set but not used [-Wunused-but-set-variable]
It is not used since commit b131a8425c ("powerpc/powernv:
Set PELTV for compound PEs")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1574144074-142032-6-git-send-email-zhengbin13@huawei.com
Fix a typo introduced during recent code cleanup, which could lead to
silently not freeing resources or an oops message (on PCI hotplug or
CAPI reset).
Only impacts ioda2, the code path for ioda1 is correct.
Fixes: 01e12629af ("powerpc/powernv/pci: Add explicit tracking of the DMA setup state")
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200819130741.16769-1-fbarrat@linux.ibm.com
Rework the PE allocation logic to allow allocating blocks of PEs rather
than individually. We'll use this to allocate contigious blocks of PEs for
the SR-IOVs.
This patch also adds code to pnv_ioda_alloc_pe() and pnv_ioda_reserve_pe() to
use the existing, but unused, phb->pe_alloc_mutex. Currently these functions
use atomic bit ops to release a currently allocated PE number. However,
the pnv_ioda_alloc_pe() wants to have exclusive access to the bit map while
scanning for hole large enough to accomodate the allocation size.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-10-oohall@gmail.com
pci-ioda.c is getting a bit unwieldly due to the amount of stuff jammed in
there. The SR-IOV support can be extracted easily enough and is mostly
standalone, so move it into a separate file.
This patch also moves the PowerNV SR-IOV specific fields from pci_dn and
moves them into a platform specific structure. I'm not sure how they ended
up in there in the first place, but leaking platform specifics into common
code has proven to be a terrible idea so far so lets stop doing that.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-5-oohall@gmail.com
We pre-configure the m64 window for IODA1 as a 1-1 segment-PE mapping,
similar to PHB3. Currently the actual mapping of segments occurs in
pnv_ioda_pick_m64_pe(), but we can move it into pnv_ioda1_init_m64() and
drop the IODA1 specific code paths in the PE setup / teardown.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-4-oohall@gmail.com
There's an optimisation in the PE setup which skips performing DMA
setup for a PE if we only have bridges in a PE. The assumption being
that only "real" devices will DMA to system memory, which is probably
fair. However, if we start off with only bridge devices in a PE then
add a non-bridge device the new device won't be able to use DMA because
we never configured it.
Fix this (admittedly pretty weird) edge case by tracking whether we've done
the DMA setup for the PE or not. If a non-bridge device is added to the PE
(via rescan or hotplug, or whatever) we can set up DMA on demand.
This also means the only remaining user of the old "DMA Weight" code is
the IODA1 DMA setup code that it was originally added for, which is good.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-3-oohall@gmail.com
Currently we have these two functions:
pnv_pci_ioda2_release_dma_pe(), and
pnv_pci_ioda2_release_pe_dma()
The first is used when tearing down VF PEs and the other is used for normal
devices. There's very little difference between the two though. The latter
(non-VF) will skip a call to pnv_pci_ioda2_unset_window() unless
CONFIG_IOMMU_API=y is set. There's no real point in doing this so fold the
two together.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-2-oohall@gmail.com
Add a helper to go from a pci_bus structure to the pnv_phb that hosts
that bus. There's a lot of instances of the following pattern:
struct pci_controller *hose = pci_bus_to_host(pdev->bus);
struct pnv_phb *phb = hose->private_data;
Without any other uses of the pci_controller inside the function. This
is hard to read since it requires you to memorise the contents of the
private data fields and kind of error prone since it involves blindly
assigning a void pointer. Add a helper to make it more concise and
explicit.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-1-oohall@gmail.com
pnv_ioda_setup_bus_dma() is only used when a passed through PE is
returned to the host. If the kernel is built without IOMMU support
this is dead code. Move it under the #ifdef with the rest of the
IOMMU API support.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200705133557.443607-2-oohall@gmail.com
The kernel test robot noticed these are non-static which causes Clang to
print some warnings. These are called via ppc_md function pointers so
there's no need for them to be non-static.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200705133557.443607-1-oohall@gmail.com
pnv_pci_ioda_configure_bus() should now only ever be called when a device is
added to the bus so add a WARN_ON() to the empty bus check. Similarly,
pnv_pci_ioda_setup_bus_PE() should only ever be called for an unconfigured PE,
so add a WARN_ON() for that case too.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200417073508.30356-5-oohall@gmail.com
Doing it once during boot rather than doing it on the fly and drop the janky
populated logic.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200417073508.30356-4-oohall@gmail.com
For normal PHBs IODA PEs are handled on a per-bus basis so all the devices
on that bus will share a PE. Which PE specificly is determined by the location
of the MMIO BARs for the devices on the bus so we can't actually configure the
bus PEs until after MMIO resources are allocated. As a result PEs are currently
configured by pcibios_setup_bridge(), which is called just before the bridge
windows are programmed into the bus' parent bridge. Configuring the bus PE here
causes a few problems:
1. The root bus doesn't have a parent bridge so setting up the PE for the root
bus requires some hacks.
2. The PELT-V isn't setup correctly because pnv_ioda_set_peltv() assumes that
PEs will be configured in root-to-leaf order. This assumption is broken
because resource assignment is performed depth-first so the leaf bridges
are setup before their parents are. The hack mentioned in 1) results in
the "correct" PELT-V for busses immediately below the root port, but not
for devices below a switch.
3. It's possible to break the sysfs PCI rescan feature by removing all
the devices on a bus. When the last device is removed from a PE its
will be de-configured. Rescanning the devices on a bus does not cause
the bridge to be reconfigured rendering the devices on that bus
unusable.
We can address most of these problems by moving the PE setup out of
pcibios_setup_bridge() and into pcibios_bus_add_device(). This fixes 1)
and 2) because pcibios_bus_add_device() is called on each device in
root-to-leaf order so PEs for parent buses will always be configured
before their children. It also fixes 3) by ensuring the PE is
configured before initialising DMA for the device. In the event the PE
was de-configured due to removing all the devices in that PE it will
now be reconfigured when a new device is added since there's no
dependecy on the bridge_setup() hook being called.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200417073508.30356-3-oohall@gmail.com
For each PHB we maintain a reverse-map that can be used to find the
PE that a BDFN is currently mapped to. Add a helper for doing this
lookup so we can check if a PE has been configured without looking
at pdn->pe_number.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200417073508.30356-2-oohall@gmail.com
Quite useful to know in some cases.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200408112213.5549-1-oohall@gmail.com
The NVlink IOMMU group setup is only relevant to NVLink devices so move
it into the NPU containment zone. This let us remove some prototypes in
pci.h and staticfy some function definitions.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200406030745.24595-8-oohall@gmail.com
Move it in with the rest of the TCE wrangling rather than carting around
a static prototype in pci-ioda.c
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200406030745.24595-7-oohall@gmail.com
Historically adding devices to their respective iommu group has been
handled by the post-init phb fixup for most devices. This was done
because:
1) The IOMMU group is tied to the PE (usually) so we can only setup the
iommu groups after we've done resource allocation since BAR location
determines the device's PE, and:
2) The sysfs directory for the pci_dev needs to be available since
iommu_add_device() wants to add an attribute for the iommu group.
However, since commit 30d87ef8b3 ("powerpc/pci: Fix
pcibios_setup_device() ordering") both conditions are met when
hose->ops->dma_dev_setup() is called so there's no real need to do
this in the fixup.
Moving the call to iommu_add_device() into pnv_pci_ioda_dma_setup_dev()
is a nice cleanup since it puts all the per-device IOMMU setup into one
place. It also results in all (non-nvlink) devices getting their iommu
group via a common path rather than relying on the bus notifier hack
in pnv_tce_iommu_bus_notifier() to handle the adding VFs and
hotplugged devices to their group.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200406030745.24595-5-oohall@gmail.com
Move the registration of IOMMU groups out of the post-phb init fixup and
into when we configure DMA for a PE. For most devices this doesn't
result in any functional changes, but for NVLink attached GPUs it
requires a bit of care. When the GPU is probed an IOMMU group would be
created for the PE that contains it. We need to ensure that group is
removed before we add the PE to the compound group that's used to keep
the translations see by the PCIe and NVLink buses the same.
No functional changes. Probably.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200406030745.24595-4-oohall@gmail.com
In pnv_ioda_setup_vf_PE() we register an iommu group for the VF PE
then call pnv_ioda_setup_bus_iommu_group() to add devices to that group.
However, this function is called before the VFs are scanned so there's
no devices to add.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200406030745.24595-3-oohall@gmail.com
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200209105901.1620958-6-gregkh@linuxfoundation.org
This is only used in pci-ioda.c so move it there and rename it to match.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200110070207.439-6-oohall@gmail.com
pnv_pci_dma_dev_setup() does nothing but call the phb->dma_dev_setup()
callback, if one exists. That callback is only set for normal PCIe PHBs so
we can remove the layer of indirection and use the ioda version in
the pci_controller_ops.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200110070207.439-5-oohall@gmail.com
An ioda_pe for each VF is allocated in pnv_pci_sriov_enable() before
the pci_dev for the VF is created. We need to set the pe->pdev pointer
at some point after the pci_dev is created. Currently we do that in:
pcibios_bus_add_device()
pnv_pci_dma_dev_setup() (via phb->ops.dma_dev_setup)
/* fixup is done here */
pnv_pci_ioda_dma_dev_setup() (via pnv_phb->dma_dev_setup)
The fixup needs to be done before setting up DMA for for the VF's PE,
but there's no real reason to delay it until this point. Move the
fixup into pnv_pci_ioda_fixup_iov() so the ordering is:
pcibios_add_device()
pnv_pci_ioda_fixup_iov() (via ppc_md.pcibios_fixup_sriov)
pcibios_bus_add_device()
...
This isn't strictly required, but it's a slightly more logical place
to do the fixup and it simplifies pnv_pci_dma_dev_setup().
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200110070207.439-4-oohall@gmail.com
The pnv_pci_dma_dev_setup() only does something when:
1) There PHB contains VFs, or
2) The PHB defines a dma_dev_setup() callback in the pnv_phb structure.
Neither is true for NPU PHBs so there's no reason to set the callback.
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200110070207.439-3-oohall@gmail.com
Add a debugfs entry to dump the state of the active IODA PEs. The IODA
PE state reflects how the PHB's internal concept of a PE is
configured. This is separate to the EEH PE state and is managed power
the PowerNV PCI backend rather than the EEH core.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[mpe: Use DEFINE_DEBUGFS_ATTRIBUTE]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190912052945.12589-3-oohall@gmail.com
Make the dump trigger off any input rather than just '1'. This allows you
to write "echo 1> dump_diag_data" and it'll do what you want rather than
erroring out pointlessly.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190912052945.12589-2-oohall@gmail.com
Use the pnv_phb structure as the private data pointer for the debugfs
files. This lets us delete some code and an open-coded use of
hose->private_data.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190912052945.12589-1-oohall@gmail.com
The powerpc PCI code requires that a pci_dn structure exists for all
devices in the system. This is fine for real devices since at boot a pci_dn
is created for each PCI device in the DT and it's fine for hotplugged devices
since the hotplug slot driver will manage the pci_dn's devices in hotplug
slots. For SR-IOV, we need the platform / pcibios to manage the pci_dn for
virtual functions since firmware is unaware of VFs, and they aren't
"hot plugged" in the traditional sense.
Management of the pci_dn is handled by the, poorly named, functions:
add_pci_dev_data() and remove_pci_dev_data(). The entire body of these
functions is #ifdef`ed around CONFIG_PCI_IOV and they cannot be used
in any other context, so make them only available when CONFIG_PCI_IOV
is selected, and rename them to reflect their actual usage rather than
having them masquerade as generic code.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190821062655.19735-2-oohall@gmail.com
With hotplug, an opencapi device can now go away. It needs to be
released, mostly to clean up its PE state. We were previously not
defining any device callback. We can reuse the standard PCI release
callback, it does a bit too much for an opencapi device, but it's
harmless, and only needs minor tuning.
Also separate the undo of the PELT-V code in a separate function, it
is not needed for NPU devices and it improves a bit the readability of
the code.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-5-fbarrat@linux.ibm.com
The PE for an opencapi device was set as part of a late PHB fixup
operation, when creating the PHB. To use the PCI hotplug framework,
this is not going to work, as the PHB stays the same, it's only the
devices underneath which are updated. For regular PCI devices, it is
done as part of the reconfiguration of the bridge, but for opencapi
PHBs, we don't have an intermediate bridge. So let's define the PE
when the device is enabled. PEs are meaningless for opencapi, the NPU
doesn't define them and opal is not doing anything with them.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-4-fbarrat@linux.ibm.com
Protect the PHB's list of PE. Probably not needed as long as it was
populated during PHB creation, but it feels right and will become
required once we can add/remove opencapi devices on hotplug.
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-3-fbarrat@linux.ibm.com
The pci_dn structure used to store a pointer to the struct pci_dev, so
taking a reference on the device was required. However, the pci_dev
pointer was later removed from the pci_dn structure, but the reference
was kept for the npu device.
See commit 902bdc5745 ("powerpc/powernv/idoa: Remove unnecessary
pcidev from pci_dn").
We don't need to take a reference on the device when assigning the PE
as the struct pnv_ioda_pe is cleaned up at the same time as
the (physical) device is released. Doing so prevents the device from
being released, which is a problem for opencapi devices, since we want
to be able to remove them through PCI hotplug.
Now the ugly part: nvlink npu devices are not meant to be
released. Because of the above, we've always leaked a reference and
simply removing it now is dangerous and would likely require more
work. There's currently no release device callback for nvlink devices
for example. So to be safe, this patch leaks a reference on the npu
device, but only for nvlink and not opencapi.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-2-fbarrat@linux.ibm.com
Use resource_size rather than a verbose computation on
the end and start fields.
The semantic patch that makes these changes is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@ struct resource ptr; @@
- (ptr.end - ptr.start + 1)
+ resource_size(&ptr)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1577900990-8588-11-git-send-email-Julia.Lawall@inria.fr
On pseries there is a bug with adding hotplugged devices to an IOMMU
group. For a number of dumb reasons fixing that bug first requires
re-working how VFs are configured on PowerNV. For background, on
PowerNV we use the pcibios_sriov_enable() hook to do two things:
1. Create a pci_dn structure for each of the VFs, and
2. Configure the PHB's internal BARs so the MMIO range for each VF
maps to a unique PE.
Roughly speaking a PE is the hardware counterpart to a Linux IOMMU
group since all the devices in a PE share the same IOMMU table. A PE
also defines the set of devices that should be isolated in response to
a PCI error (i.e. bad DMA, UR/CA, AER events, etc). When isolated all
MMIO and DMA traffic to and from devicein the PE is blocked by the
root complex until the PE is recovered by the OS.
The requirement to block MMIO causes a giant headache because the P8
PHB generally uses a fixed mapping between MMIO addresses and PEs. As
a result we need to delay configuring the IOMMU groups for device
until after MMIO resources are assigned. For physical devices (i.e.
non-VFs) the PE assignment is done in pcibios_setup_bridge() which is
called immediately after the MMIO resources for downstream
devices (and the bridge's windows) are assigned. For VFs the setup is
more complicated because:
a) pcibios_setup_bridge() is not called again when VFs are activated, and
b) The pci_dev for VFs are created by generic code which runs after
pcibios_sriov_enable() is called.
The work around for this is a two step process:
1. A fixup in pcibios_add_device() is used to initialised the cached
pe_number in pci_dn, then
2. A bus notifier then adds the device to the IOMMU group for the PE
specified in pci_dn->pe_number.
A side effect fixing the pseries bug mentioned in the first paragraph
is moving the fixup out of pcibios_add_device() and into
pcibios_bus_add_device(), which is called much later. This results in
step 2. failing because pci_dn->pe_number won't be initialised when
the bus notifier is run.
We can fix this by removing the need for the fixup. The PE for a VF is
known before the VF is even scanned so we can initialise
pci_dn->pe_number pcibios_sriov_enable() instead. Unfortunately,
moving the initialisation causes two problems:
1. We trip the WARN_ON() in the current fixup code, and
2. The EEH core clears pdn->pe_number when recovering a VF and
relies on the fixup to correctly re-set it.
The only justification for either of these is a comment in
eeh_rmv_device() suggesting that pdn->pe_number *must* be set to
IODA_INVALID_PE in order for the VF to be scanned. However, this
comment appears to have no basis in reality. Both bugs can be fixed by
just deleting the code.
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191028085424.12006-1-oohall@gmail.com
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1545705876-63132-1-git-send-email-yuehaibing@huawei.com
As now we have xchg_no_kill/tce_kill, these are not used anymore so
remove them.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190829085252.72370-6-aik@ozlabs.ru
At the moment updates in a TCE table are made by iommu_table_ops::exchange
which update one TCE and invalidates an entry in the PHB/NPU TCE cache
via set of registers called "TCE Kill" (hence the naming).
Writing a TCE is a simple xchg() but invalidating the TCE cache is
a relatively expensive OPAL call. Mapping a 100GB guest with PCI+NPU
passed through devices takes about 20s.
Thankfully we can do better. Since such big mappings happen at the boot
time and when memory is plugged/onlined (i.e. not often), these requests
come in 512 pages so we call call OPAL 512 times less which brings 20s
from the above to less than 10s. Also, since TCE caches can be flushed
entirely, calling OPAL for 512 TCEs helps skiboot [1] to decide whether
to flush the entire cache or not.
This implements 2 new iommu_table_ops callbacks:
- xchg_no_kill() to update a single TCE with no TCE invalidation;
- tce_kill() to invalidate multiple TCEs.
This uses the same xchg_no_kill() callback for IODA1/2.
This implements 2 new wrappers on top of the new callbacks similar to
the existing iommu_tce_xchg().
This does not use the new callbacks yet, the next patches will;
so this should not cause any behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190829085252.72370-2-aik@ozlabs.ru
At the moment we create a small window only for 32bit devices, the window
maps 0..2GB of the PCI space only. For other devices we either use
a sketchy bypass or hardware bypass but the former can only work if
the amount of RAM is no bigger than the device's DMA mask and the latter
requires devices to support at least 59bit DMA.
This extends the default DMA window to the maximum size possible to allow
a wider DMA mask than just 32bit. The default window size is now limited
by the the iommu_table::it_map allocation bitmap which is a contiguous
array, 1 bit per an IOMMU page.
This increases the default IOMMU page size from hard coded 4K to
the system page size to allow wider DMA masks.
This increases the level number to not exceed the max order allocation
limit per TCE level. By the same time, this keeps minimal levels number
as 2 in order to save memory.
As the extended window now overlaps the 32bit MMIO region, this adds
an area reservation to iommu_init_table().
After this change the default window size is 0x80000000000==1<<43 so
devices limited to DMA mask smaller than the amount of system RAM can
still use more than just 2GB of memory for DMA.
This is an optimization and not a bug fix for DMA API usage.
With the on-demand allocation of indirect TCE table levels enabled and
2 levels, the first TCE level size is just
1<<ceil((log2(0x7ffffffffff+1)-16)/2)=16384 TCEs or 2 system pages.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190718051139.74787-5-aik@ozlabs.ru
Notable changes:
- Removal of the NPU DMA code, used by the out-of-tree Nvidia driver, as well
as some other functions only used by drivers that haven't (yet?) made it
upstream.
- A fix for a bug in our handling of hardware watchpoints (eg. perf record -e
mem: ...) which could lead to register corruption and kernel crashes.
- Enable HAVE_ARCH_HUGE_VMAP, which allows us to use large pages for vmalloc
when using the Radix MMU.
- A large but incremental rewrite of our exception handling code to use gas
macros rather than multiple levels of nested CPP macros.
And the usual small fixes, cleanups and improvements.
Thanks to:
Alastair D'Silva, Alexey Kardashevskiy, Andreas Schwab, Aneesh Kumar K.V, Anju
T Sudhakar, Anton Blanchard, Arnd Bergmann, Athira Rajeev, Cédric Le Goater,
Christian Lamparter, Christophe Leroy, Christophe Lombard, Christoph Hellwig,
Daniel Axtens, Denis Efremov, Enrico Weigelt, Frederic Barrat, Gautham R.
Shenoy, Geert Uytterhoeven, Geliang Tang, Gen Zhang, Greg Kroah-Hartman, Greg
Kurz, Gustavo Romero, Krzysztof Kozlowski, Madhavan Srinivasan, Masahiro
Yamada, Mathieu Malaterre, Michael Neuling, Nathan Lynch, Naveen N. Rao,
Nicholas Piggin, Nishad Kamdar, Oliver O'Halloran, Qian Cai, Ravi Bangoria,
Sachin Sant, Sam Bobroff, Satheesh Rajendran, Segher Boessenkool, Shaokun
Zhang, Shawn Anastasio, Stewart Smith, Suraj Jitindar Singh, Thiago Jung
Bauermann, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=3dBZ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Removal of the NPU DMA code, used by the out-of-tree Nvidia driver,
as well as some other functions only used by drivers that haven't
(yet?) made it upstream.
- A fix for a bug in our handling of hardware watchpoints (eg. perf
record -e mem: ...) which could lead to register corruption and
kernel crashes.
- Enable HAVE_ARCH_HUGE_VMAP, which allows us to use large pages for
vmalloc when using the Radix MMU.
- A large but incremental rewrite of our exception handling code to
use gas macros rather than multiple levels of nested CPP macros.
And the usual small fixes, cleanups and improvements.
Thanks to: Alastair D'Silva, Alexey Kardashevskiy, Andreas Schwab,
Aneesh Kumar K.V, Anju T Sudhakar, Anton Blanchard, Arnd Bergmann,
Athira Rajeev, Cédric Le Goater, Christian Lamparter, Christophe
Leroy, Christophe Lombard, Christoph Hellwig, Daniel Axtens, Denis
Efremov, Enrico Weigelt, Frederic Barrat, Gautham R. Shenoy, Geert
Uytterhoeven, Geliang Tang, Gen Zhang, Greg Kroah-Hartman, Greg Kurz,
Gustavo Romero, Krzysztof Kozlowski, Madhavan Srinivasan, Masahiro
Yamada, Mathieu Malaterre, Michael Neuling, Nathan Lynch, Naveen N.
Rao, Nicholas Piggin, Nishad Kamdar, Oliver O'Halloran, Qian Cai, Ravi
Bangoria, Sachin Sant, Sam Bobroff, Satheesh Rajendran, Segher
Boessenkool, Shaokun Zhang, Shawn Anastasio, Stewart Smith, Suraj
Jitindar Singh, Thiago Jung Bauermann, YueHaibing"
* tag 'powerpc-5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (163 commits)
powerpc/powernv/idle: Fix restore of SPRN_LDBAR for POWER9 stop state.
powerpc/eeh: Handle hugepages in ioremap space
ocxl: Update for AFU descriptor template version 1.1
powerpc/boot: pass CONFIG options in a simpler and more robust way
powerpc/boot: add {get, put}_unaligned_be32 to xz_config.h
powerpc/irq: Don't WARN continuously in arch_local_irq_restore()
powerpc/module64: Use symbolic instructions names.
powerpc/module32: Use symbolic instructions names.
powerpc: Move PPC_HA() PPC_HI() and PPC_LO() to ppc-opcode.h
powerpc/module64: Fix comment in R_PPC64_ENTRY handling
powerpc/boot: Add lzo support for uImage
powerpc/boot: Add lzma support for uImage
powerpc/boot: don't force gzipped uImage
powerpc/8xx: Add microcode patch to move SMC parameter RAM.
powerpc/8xx: Use IO accessors in microcode programming.
powerpc/8xx: replace #ifdefs by IS_ENABLED() in microcode.c
powerpc/8xx: refactor programming of microcode CPM params.
powerpc/8xx: refactor printing of microcode patch name.
powerpc/8xx: Refactor microcode write
powerpc/8xx: refactor writing of CPM microcode arrays
...
The powernv platform uses @dma_iommu_ops for non-bypass DMA. These ops
need an iommu_table pointer which is stored in
dev->archdata.iommu_table_base. It is initialized during
pcibios_setup_device() which handles boot time devices. However when a
device is taken from the system in order to pass it through, the
default IOMMU table is destroyed but the pointer in a device is not
updated; also when a device is returned back to the system, a new
table pointer is not stored in dev->archdata.iommu_table_base either.
So when a just returned device tries using IOMMU, it crashes on
accessing stale iommu_table or its members.
This calls set_iommu_table_base() when the default window is created.
Note it used to be there before but was wrongly removed (see "fixes").
It did not appear before as these days most devices simply use bypass.
This adds set_iommu_table_base(NULL) when a device is taken from the
system to make it clear that IOMMU DMA cannot be used past that point.
Fixes: c4e9d3c1e6 ("powerpc/powernv/pseries: Rework device adding to IOMMU groups")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These have been unused anywhere in the kernel tree ever since they've
been added to the kernel.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the return value type was changed from int to bool, few places
were left unchanged, this fixes them. We did not hit these failures as
the first one is not happening at all and the second one is little
more likely to happen if the user switches a 33..58bit DMA capable
device between the VFIO and vendor drivers and there are not so many
of these.
Fixes: 2d6ad41b2c ("powerpc/powernv: use the generic iommu bypass code")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
