x86_flattree_get_config() is incorrectly protected by
ifdef CONFIG_OF_FLATTREE. It uses of_get_flat_dt_size(), which
only exists if CONFIG_OF_EARLY_FLATTREE. This issue has not
been exposed previously because OF_FLATTREE did not occur unless
it was selected by OF_EARLY_FLATTREE. A devicetree overlay change
is selecting OF_FLATTREE directly instead of indirectly enabling
it by selecting OF_EARLY_FLATTREE.
This problem was exposed by a randconfig generated by the kbuild
test robot, where Platform OLPC was enabled. OLPC selects
OF_PROMTREE instead of OF_EARLY_FLATREE. The only other x86
platform that selects OF is X86_INTEL_CE, which does select
OF_EARLY_FLATTREE.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
The pending interrupt check code is old, update the following:
- Use for_each_set_bit() instead of open coding it
- Replace printk() with pr_err()
- Get rid of printk line breaks
- Make curly braces balanced
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: bhe@redhat.com
Cc: ebiederm@xmission.com
Link: https://lkml.kernel.org/r/20180301055930.2396-3-douly.fnst@cn.fujitsu.com
The pending interrupt check code is mixed with the local APIC setup code,
that looks messy.
Extract the related code, move it into a new function named
apic_pending_intr_clear().
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: bhe@redhat.com
Cc: ebiederm@xmission.com
Link: https://lkml.kernel.org/r/20180301055930.2396-2-douly.fnst@cn.fujitsu.com
The separation of the cpu_entry_area from the fixmap missed the fact that
on 32bit non-PAE kernels the cpu_entry_area mapping might not be covered in
initial_page_table by the previous synchronizations.
This results in suspend/resume failures because 32bit utilizes initial page
table for resume. The absence of the cpu_entry_area mapping results in a
triple fault, aka. insta reboot.
With PAE enabled this works by chance because the PGD entry which covers
the fixmap and other parts incindentally provides the cpu_entry_area
mapping as well.
Synchronize the initial page table after setting up the cpu entry
area. Instead of adding yet another copy of the same code, move it to a
function and invoke it from the various places.
It needs to be investigated if the existing calls in setup_arch() and
setup_per_cpu_areas() can be replaced by the later invocation from
setup_cpu_entry_areas(), but that's beyond the scope of this fix.
Fixes: 92a0f81d89 ("x86/cpu_entry_area: Move it out of the fixmap")
Reported-by: Woody Suwalski <terraluna977@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Woody Suwalski <terraluna977@gmail.com>
Cc: William Grant <william.grant@canonical.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1802282137290.1392@nanos.tec.linutronix.de
Pull x86 fixes from Thomas Gleixner:
"Yet another pile of melted spectrum related changes:
- sanitize the array_index_nospec protection mechanism: Remove the
overengineered array_index_nospec_mask_check() magic and allow
const-qualified types as index to avoid temporary storage in a
non-const local variable.
- make the microcode loader more robust by properly propagating error
codes. Provide information about new feature bits after micro code
was updated so administrators can act upon.
- optimizations of the entry ASM code which reduce code footprint and
make the code simpler and faster.
- fix the {pmd,pud}_{set,clear}_flags() implementations to work
properly on paravirt kernels by removing the address translation
operations.
- revert the harmful vmexit_fill_RSB() optimization
- use IBRS around firmware calls
- teach objtool about retpolines and add annotations for indirect
jumps and calls.
- explicitly disable jumplabel patching in __init code and handle
patching failures properly instead of silently ignoring them.
- remove indirect paravirt calls for writing the speculation control
MSR as these calls are obviously proving the same attack vector
which is tried to be mitigated.
- a few small fixes which address build issues with recent compiler
and assembler versions"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
KVM/VMX: Optimize vmx_vcpu_run() and svm_vcpu_run() by marking the RDMSR path as unlikely()
KVM/x86: Remove indirect MSR op calls from SPEC_CTRL
objtool, retpolines: Integrate objtool with retpoline support more closely
x86/entry/64: Simplify ENCODE_FRAME_POINTER
extable: Make init_kernel_text() global
jump_label: Warn on failed jump_label patching attempt
jump_label: Explicitly disable jump labels in __init code
x86/entry/64: Open-code switch_to_thread_stack()
x86/entry/64: Move ASM_CLAC to interrupt_entry()
x86/entry/64: Remove 'interrupt' macro
x86/entry/64: Move the switch_to_thread_stack() call to interrupt_entry()
x86/entry/64: Move ENTER_IRQ_STACK from interrupt macro to interrupt_entry
x86/entry/64: Move PUSH_AND_CLEAR_REGS from interrupt macro to helper function
x86/speculation: Move firmware_restrict_branch_speculation_*() from C to CPP
objtool: Add module specific retpoline rules
objtool: Add retpoline validation
objtool: Use existing global variables for options
x86/mm/sme, objtool: Annotate indirect call in sme_encrypt_execute()
x86/boot, objtool: Annotate indirect jump in secondary_startup_64()
x86/paravirt, objtool: Annotate indirect calls
...
- optimization for the exitless interrupt support that was merged in 4.16-rc1
- improve the branch prediction blocking for nested KVM
- replace some jump tables with switch statements to improve expoline performance
- fixes for multiple epoch facility
ARM:
- fix the interaction of userspace irqchip VMs with in-kernel irqchip VMs
- make sure we can build 32-bit KVM/ARM with gcc-8.
x86:
- fixes for AMD SEV
- fixes for Intel nested VMX, emulated UMIP and a dump_stack() on VM startup
- fixes for async page fault migration
- small optimization to PV TLB flush (new in 4.16-rc1)
- syzkaller fixes
Generic:
- compiler warning fixes
- syzkaller fixes
- more improvements to the kvm_stat tool
Two more small Spectre fixes are going to reach you via Ingo.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEbBAABAgAGBQJakL/fAAoJEL/70l94x66Dzp4H9j6qMzgOTAQ0bYmupQp81tad
V8lNabVSNi0UBYwk2D44oNigtNjQckE18KGnjuJ4tZW+GZ+D7zrrHrKXWtATXgxP
SIfHj+raSd/lgJoy6HLu/N0oT6wS+PdZMYFgSu600Vi618lGKGX1SIAwBhjoxdMX
7QKKAuPcDZ1qgGddhWaLnof28nQQEWcCAVfFeVojmM0TyhvSbgSysh/Gq10ydybh
NVUfgP3fzLtT9gVngX/ZtbogNkltPYmucpI+wT3nWfsgBic783klfWrfpnC/GM85
OeXLVhHwVLG6tXUGhb4ULO+F9HwRGX31+er6iIxmwH9PvqnQMRcQ0Xxf2gbNXg==
=YmH6
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"s390:
- optimization for the exitless interrupt support that was merged in 4.16-rc1
- improve the branch prediction blocking for nested KVM
- replace some jump tables with switch statements to improve expoline performance
- fixes for multiple epoch facility
ARM:
- fix the interaction of userspace irqchip VMs with in-kernel irqchip VMs
- make sure we can build 32-bit KVM/ARM with gcc-8.
x86:
- fixes for AMD SEV
- fixes for Intel nested VMX, emulated UMIP and a dump_stack() on VM startup
- fixes for async page fault migration
- small optimization to PV TLB flush (new in 4.16-rc1)
- syzkaller fixes
Generic:
- compiler warning fixes
- syzkaller fixes
- more improvements to the kvm_stat tool
Two more small Spectre fixes are going to reach you via Ingo"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (40 commits)
KVM: SVM: Fix SEV LAUNCH_SECRET command
KVM: SVM: install RSM intercept
KVM: SVM: no need to call access_ok() in LAUNCH_MEASURE command
include: psp-sev: Capitalize invalid length enum
crypto: ccp: Fix sparse, use plain integer as NULL pointer
KVM: X86: Avoid traversing all the cpus for pv tlb flush when steal time is disabled
x86/kvm: Make parse_no_xxx __init for kvm
KVM: x86: fix backward migration with async_PF
kvm: fix warning for non-x86 builds
kvm: fix warning for CONFIG_HAVE_KVM_EVENTFD builds
tools/kvm_stat: print 'Total' line for multiple events only
tools/kvm_stat: group child events indented after parent
tools/kvm_stat: separate drilldown and fields filtering
tools/kvm_stat: eliminate extra guest/pid selection dialog
tools/kvm_stat: mark private methods as such
tools/kvm_stat: fix debugfs handling
tools/kvm_stat: print error on invalid regex
tools/kvm_stat: fix crash when filtering out all non-child trace events
tools/kvm_stat: avoid 'is' for equality checks
tools/kvm_stat: use a more pythonic way to iterate over dictionaries
...
Add a more versatile memmap= operator, which -- in addition to all the
things that were possible before -- allows you to:
- redeclare existing ranges -- before, you were limited to adding ranges;
- drop any range -- like a mem= for any location;
- use any e820 memory type -- not just some predefined ones.
The syntax is:
memmap=<size>%<offset>-<oldtype>+<newtype>
Size and offset work as usual. The "-<oldtype>" and "+<newtype>" are
optional and their existence determine the behavior: The command
works on the specified range of memory limited to type <oldtype>
(if specified). This memory is then configured to show up as <newtype>.
If <newtype> is not specified, the memory is removed from the e820 map.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180202231020.15608-1-jschoenh@amazon.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Make the noop functions in x86_init.c static in case they are used
locally only.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180221094232.23462-1-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a new struct x86_init_acpi to x86_init_ops. For now it contains
only one init function to get the RSDP table address.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: boris.ostrovsky@oracle.com
Cc: lenb@kernel.org
Cc: linux-acpi@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20180219100906.14265-3-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 fixes from Thomas Gleixner:
"A small set of fixes:
- UAPI data type correction for hyperv
- correct the cpu cores field in /proc/cpuinfo on CPU hotplug
- return proper error code in the resctrl file system failure path to
avoid silent subsequent failures
- correct a subtle accounting issue in the new vector allocation code
which went unnoticed for a while and caused suspend/resume
failures"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/topology: Update the 'cpu cores' field in /proc/cpuinfo correctly across CPU hotplug operations
x86/topology: Fix function name in documentation
x86/intel_rdt: Fix incorrect returned value when creating rdgroup sub-directory in resctrl file system
x86/apic/vector: Handle vector release on CPU unplug correctly
genirq/matrix: Handle CPU offlining proper
x86/headers/UAPI: Use __u64 instead of u64 in <uapi/asm/hyperv.h>
Avoid traversing all the cpus for pv tlb flush when steal time
is disabled since pv tlb flush depends on the field in steal time
for shared data.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The early_param() is only called during kernel initialization, So Linux
marks the functions of it with __init macro to save memory.
But it forgot to mark the parse_no_kvmapf/stealacc/kvmclock_vsyscall,
So, Make them __init as well.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: rkrcmar@redhat.com
Cc: kvm@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: x86@kernel.org
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Guests on new hypersiors might set KVM_ASYNC_PF_DELIVERY_AS_PF_VMEXIT
bit when enabling async_PF, but this bit is reserved on old hypervisors,
which results in a failure upon migration.
To avoid breaking different cases, we are checking for CPUID feature bit
before enabling the feature and nothing else.
Fixes: 52a5c155cf ("KVM: async_pf: Let guest support delivery of async_pf from guest mode")
Cc: <stable@vger.kernel.org>
Reviewed-by: Wanpeng Li <wanpengli@tencent.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Without this fix, /proc/cpuinfo will display an incorrect amount
of CPU cores, after bringing them offline and online again, as
exemplified below:
$ cat /proc/cpuinfo | grep cores
cpu cores : 4
cpu cores : 8
cpu cores : 8
cpu cores : 20
cpu cores : 4
cpu cores : 3
cpu cores : 2
cpu cores : 2
This patch fixes this by always zeroing the booted_cores variable
upon turning off a logical CPU.
Tested-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Samuel Neves <sneves@dei.uc.pt>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jgross@suse.com
Cc: luto@kernel.org
Cc: prarit@redhat.com
Cc: vkuznets@redhat.com
Link: http://lkml.kernel.org/r/20180221205036.5244-1-sneves@dei.uc.pt
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If no monitoring feature is detected because all monitoring features are
disabled during boot time or there is no monitoring feature in hardware,
creating rdtgroup sub-directory by "mkdir" command reports error:
mkdir: cannot create directory ‘/sys/fs/resctrl/p1’: No such file or directory
But the sub-directory actually is generated and content is correct:
cpus cpus_list schemata tasks
The error is because rdtgroup_mkdir_ctrl_mon() returns non zero value after
the sub-directory is created and the returned value is reported as an error
to user.
Clear the returned value to report to user that the sub-directory is
actually created successfully.
Signed-off-by: Wang Hui <john.wanghui@huawei.com>
Signed-off-by: Zhang Yanfei <yanfei.zhang@huawei.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi V Shankar <ravi.v.shankar@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vikas <vikas.shivappa@intel.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Link: http://lkml.kernel.org/r/1519356363-133085-1-git-send-email-fenghua.yu@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When a irq vector is replaced, then the previous vector is normally
released when the first interrupt happens on the new vector. If the target
CPU of the previous vector is already offline when the new vector is
installed, then the previous vector is silently discarded, which leads to
accounting issues causing suspend failures and other problems.
Adjust the logic so that the previous vector is freed in the underlying
matrix allocator to ensure that the accounting stays correct.
Fixes: 69cde0004a ("x86/vector: Use matrix allocator for vector assignment")
Reported-by: Yuriy Vostrikov <delamonpansie@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Yuriy Vostrikov <delamonpansie@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180222112316.930791749@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On i386, there are 2 types of PLTs, PIC and non-PIC. PIE and shared
objects must use PIC PLT. To use PIC PLT, you need to load
_GLOBAL_OFFSET_TABLE_ into EBX first. There is no need for that on
x86-64 since x86-64 uses PC-relative PLT.
On x86-64, for 32-bit PC-relative branches, we can generate PLT32
relocation, instead of PC32 relocation, which can also be used as
a marker for 32-bit PC-relative branches. Linker can always reduce
PLT32 relocation to PC32 if function is defined locally. Local
functions should use PC32 relocation. As far as Linux kernel is
concerned, R_X86_64_PLT32 can be treated the same as R_X86_64_PC32
since Linux kernel doesn't use PLT.
R_X86_64_PLT32 for 32-bit PC-relative branches has been enabled in
binutils master branch which will become binutils 2.31.
[ hjl is working on having better documentation on this all, but a few
more notes from him:
"PLT32 relocation is used as marker for PC-relative branches. Because
of EBX, it looks odd to generate PLT32 relocation on i386 when EBX
doesn't have GOT.
As for symbol resolution, PLT32 and PC32 relocations are almost
interchangeable. But when linker sees PLT32 relocation against a
protected symbol, it can resolved locally at link-time since it is
used on a branch instruction. Linker can't do that for PC32
relocation"
but for the kernel use, the two are basically the same, and this
commit gets things building and working with the current binutils
master - Linus ]
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Carve out the SMCA code in get_block_address() into a separate helper
function.
No functional change.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
[ Save an indentation level. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180215210943.11530-4-Yazen.Ghannam@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The block address is saved after the block is initialized when
threshold_init_device() is called.
Use the saved block address, if available, rather than trying to
rediscover it.
This will avoid a call trace, when resuming from suspend, due to the
rdmsr_safe_on_cpu() call in get_block_address(). The rdmsr_safe_on_cpu()
call issues an IPI but we're running with interrupts disabled. This
triggers:
WARNING: CPU: 0 PID: 11523 at kernel/smp.c:291 smp_call_function_single+0xdc/0xe0
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # 4.14.x
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180221101900.10326-8-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, bank 4 is reserved on Fam17h, so we chose not to initialize
bank 4 in the smca_banks array. This means that when we check if a bank
is initialized, like during boot or resume, we will see that bank 4 is
not initialized and try to initialize it.
This will cause a call trace, when resuming from suspend, due to
rdmsr_*on_cpu() calls in the init path. The rdmsr_*on_cpu() calls issue
an IPI but we're running with interrupts disabled. This triggers:
WARNING: CPU: 0 PID: 11523 at kernel/smp.c:291 smp_call_function_single+0xdc/0xe0
...
Reserved banks will be read-as-zero, so their MCA_IPID register will be
zero. So, like the smca_banks array, the threshold_banks array will not
have an entry for a reserved bank since all its MCA_MISC* registers will
be zero.
Enumerate a "Reserved" bank type that matches on a HWID_MCATYPE of 0,0.
Use the "Reserved" type when checking if a bank is reserved. It's
possible that other bank numbers may be reserved on future systems.
Don't try to find the block address on reserved banks.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # 4.14.x
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180221101900.10326-7-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pass the bank number to smca_get_bank_type() since that's all we need.
Also, we should compare the bank number to MAX_NR_BANKS (size of the
smca_banks array) not the number of bank types. Bank types are reused
for multiple banks, so the number of types can be different from the
number of banks in a system and thus we could return an invalid bank
type.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # 4.14.x
Cc: <stable@vger.kernel.org> # 4.14.x: 11cf887728 x86/MCE/AMD: Define a function to get SMCA bank type
Cc: <stable@vger.kernel.org> # 4.14.x: c6708d50f1 x86/MCE: Report only DRAM ECC as memory errors on AMD systems
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180221101900.10326-6-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The MCA banks log error info into MCA_ADDR, MCA_MISC0, and MCA_SYND even
if the corresponding valid bits are not set:
"Error handlers should save the values in MCA_ADDR, MCA_MISC0,
and MCA_SYND even if MCA_STATUS[AddrV], MCA_STATUS[MiscV], and
MCA_STATUS[SyndV] are zero."
Do so by setting those bits so that code down the MCE processing path
doesn't need to be changed.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180221101900.10326-5-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
... to save space when future flags are added.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180221101900.10326-3-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
... because they don't need to be exported outside of MCE.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180221101900.10326-2-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Convert init_kernel_text() to a global function and use it in a few
places instead of manually comparing _sinittext and _einittext.
Note that kallsyms.h has a very similar function called
is_kernel_inittext(), but its end check is inclusive. I'm not sure
whether that's intentional behavior, so I didn't touch it.
Suggested-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/4335d02be8d45ca7d265d2f174251d0b7ee6c5fd.1519051220.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With boot-time switching between paging modes, XEN_PV and XEN_PVH can be
boot into 4-level paging mode.
Tested-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180216114948.68868-2-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The objtool retpoline validation found this indirect jump. Seeing how
it's on CPU bringup before we run userspace it should be safe, annotate
it.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently the kdump kernel becomes very slow if 'noapic' is specified.
Normal kernel doesn't have this bug.
Kernel parameter 'noapic' is used to disable IO-APIC in system for
testing or special purpose. Here the root cause is that in kdump
kernel LAPIC is disabled since commit:
522e664644 ("x86/apic: Disable I/O APIC before shutdown of the local APIC")
In this case we need set up through-local-APIC on boot CPU in
setup_local_APIC().
In normal kernel the legacy irq mode is enabled by the BIOS. If
it is virtual wire mode, the local-APIC has been enabled and set as
through-local-APIC.
Though we fixed the regression introduced by commit 522e664644,
to further improve robustness set up the through-local-APIC mode
explicitly, do not rely on the default boot IRQ mode.
Signed-off-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: douly.fnst@cn.fujitsu.com
Cc: joro@8bytes.org
Cc: prarit@redhat.com
Cc: uobergfe@redhat.com
Link: http://lkml.kernel.org/r/20180214054656.3780-7-bhe@redhat.com
[ Rewrote the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The names of x86_io_apic_ops and its two member variables are
misleading:
The ->read() member is to read IO_APIC reg, while ->disable()
which is called by native_disable_io_apic()/irq_remapping_disable_io_apic()
is actually used to restore boot IRQ mode, not to disable the IO-APIC.
So rename x86_io_apic_ops to 'x86_apic_ops' since it doesn't only
handle the IO-APIC, but also the local APIC.
Also rename its member variables and the related callbacks.
Signed-off-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: douly.fnst@cn.fujitsu.com
Cc: joro@8bytes.org
Cc: prarit@redhat.com
Cc: uobergfe@redhat.com
Link: http://lkml.kernel.org/r/20180214054656.3780-6-bhe@redhat.com
[ Rewrote the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is a regression fix.
Before, to fix erratum AVR31, the following commit:
522e664644 ("x86/apic: Disable I/O APIC before shutdown of the local APIC")
... moved the lapic_shutdown() call to after disable_IO_APIC() in the reboot
and kexec/kdump code paths.
This introduced the following regression: disable_IO_APIC() not only clears
the IO-APIC, but it also restores boot IRQ mode by setting the
LAPIC/APIC/IMCR, calling lapic_shutdown() after disable_IO_APIC() will
disable LAPIC and ruin the possible virtual wire mode setting which
the code has been trying to do all along.
The consequence is that a KVM guest kernel always prints the warning below
during kexec/kdump as the kernel boots up:
[ 0.001000] WARNING: CPU: 0 PID: 0 at arch/x86/kernel/apic/apic.c:1467 setup_local_APIC+0x228/0x330
[ ........]
[ 0.001000] Call Trace:
[ 0.001000] apic_bsp_setup+0x56/0x74
[ 0.001000] x86_late_time_init+0x11/0x16
[ 0.001000] start_kernel+0x3c9/0x486
[ 0.001000] secondary_startup_64+0xa5/0xb0
[ ........]
[ 0.001000] masked ExtINT on CPU#0
To fix this, just call clear_IO_APIC() to stop the IO-APIC where
disable_IO_APIC() was called, and call restore_boot_irq_mode() to
restore boot IRQ mode before a reboot or a kexec/kdump jump.
Signed-off-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: douly.fnst@cn.fujitsu.com
Cc: joro@8bytes.org
Cc: prarit@redhat.com
Cc: stable@vger.kernel.org
Cc: uobergfe@redhat.com
Fixes: commit 522e664644 ("x86/apic: Disable I/O APIC before shutdown of the local APIC")
Link: http://lkml.kernel.org/r/20180214054656.3780-4-bhe@redhat.com
[ Rewrote the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Split following patches disable_IO_APIC() will be broken up into
clear_IO_APIC() and restore_boot_irq_mode().
These two functions will be called separately where they are needed
to fix a regression introduced by:
522e664644 ("x86/apic: Disable I/O APIC before shutdown of the local APIC").
While the CONFIG_KEXEC_JUMP=y code doesn't call lapic_shutdown() before jump
like kexec/kdump, so it's not impacted by commit 522e664644.
Hence here change clear_IO_APIC() as public, and replace disable_IO_APIC()
with clear_IO_APIC() and restore_boot_irq_mode() to keep CONFIG_KEXEC_JUMP=y
code unchanged in essence. No functional change.
Signed-off-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: douly.fnst@cn.fujitsu.com
Cc: joro@8bytes.org
Cc: prarit@redhat.com
Cc: uobergfe@redhat.com
Link: http://lkml.kernel.org/r/20180214054656.3780-3-bhe@redhat.com
[ Rewrote the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is a preparation patch. Split out the code which restores boot
irq mode from disable_IO_APIC() into the new restore_boot_irq_mode()
function.
No functional changes.
Signed-off-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: douly.fnst@cn.fujitsu.com
Cc: joro@8bytes.org
Cc: prarit@redhat.com
Cc: uobergfe@redhat.com
Link: http://lkml.kernel.org/r/20180214054656.3780-2-bhe@redhat.com
[ Build fix for !CONFIG_IO_APIC and rewrote the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With some microcode upgrades, new CPUID features can become visible on
the CPU. Check what the kernel has mirrored now and issue a warning
hinting at possible things the user/admin can do to make use of the
newly visible features.
Originally-by: Ashok Raj <ashok.raj@intel.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180216112640.11554-4-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a callback function which the microcode loader calls when microcode
has been updated to a newer revision. Do the callback only when no error
was encountered during loading.
Tested-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180216112640.11554-3-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
... so that callers can know when microcode was updated and act
accordingly.
Tested-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180216112640.11554-2-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Early boot code should be able to initialize page tables for both 4- and
5-level paging modes.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214182542.69302-7-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
vmemmap area has different placement depending on paging mode.
Let's adjust it during early boot accodring to machine capability.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214182542.69302-6-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
vmalloc area has different placement and size depending on paging mode.
Let's adjust it during early boot accodring to machine capability.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214182542.69302-5-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For 4- and 5-level paging we have different 'page_offset_base'.
Let's initialize it at boot-time accordingly to machine capability.
We also have to split __PAGE_OFFSET_BASE into two constants -- for 4-
and 5-level paging.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214182542.69302-4-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Switching between paging modes requires the folding of the p4d page table level
when we only have 4 paging levels, which means we need to adjust 'pgdir_shift'
and 'ptrs_per_p4d' during early boot according to paging mode.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214182542.69302-3-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
'pgtable_l5_enabled' indicates which paging mode we are using. We need to
initialize it at boot-time according to machine capability.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214182542.69302-2-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
