[Why]
New value breaks VSR on high refresh panels, reverting until a fix is developed
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
dram clock change latencies get updated using ddr4 latency table, but
does that update does not happen before validation. This value
should not be the default and should be number received from
df for better mode support.
This may cause a PState hang on high refresh panels with short vblanks
such as on 1080p 360hz or 300hz panels.
[HOW]
Update latency from 23.84 to 11.72.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the system does not have hostvm enabled, disabling it for
DML validation will allow more modes to pass at lower voltage
levels.
[How]
When initializing HostVM save state to hubbub and read back
when populating DML pipes from context.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Program modulo with ref dpp clk Mhz/10.
Program phase with pipe dpp clk Mhz /10.
DMUB FW could use these value to determine optimization clk
for PSR power saving.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When mpo enabled, video comes is 709. Desktop use sRGB.
So color change easily noticeable especially when switch between
mpo/non-mpo.
[How]
Force use sRGB for video TF is sRGB or BT709.
DCN1/DCN2 use predefined type with YUV.
DCN3 use distributed points type with YUV.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the freesync power optimization increasing vtotal, the driver
believes that MPO is supported. MPO is turned on. Freesync then
exits, MPO can no longer be supported and immediate flip fails. This
causes corruption on the panel.
[How]
Avoid the freesync optimization when doing validation so in the case
freesync exits, driver can still support the configuration.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some cases, prefetch mode 0 is unsupported but prefetch 1 is
supported. Due to previous change always forcing prefetch mode to 0, we
are failing bandwidth validation in cases where we should not.
[How]
By default try prefetch mode 0 but in the case validation fails, attempt
to do prefetch mode 1 to see if it is supported.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On APU should be always using prefetch mode 0.
Currently, sometimes prefetch mode 1 is being
used causing system to hard hang due to
minTTUVBlank being too low.
[How]
Any ASIC running DCN21 will by default allow
self refresh and mclk switch. This sets both
min and max prefetch mode to 0 by default.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some sink devices wish to have access to the minimum
HBlank supported by the ASIC.
[How]
Make the ASIC minimum HBlank available in Source
Device information address 0x340.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Enable ODM Combine + Fullscreen MPO on DCN2.1
For lower power consumption in video use cases.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Create a separate dcn21_fast_validate_bw function for dcn21.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DF PState and Voltage State are coupled such that one cannot be
raised without raising the other. This uses more power than
is necessary in high bandwidth scenarios.
[HOW]
Add logic to create a new bounding box state that allows for
DF PState to be low while Voltage State is high. Watermarks
vlevel calculation logic was also udpated to assume
state 1 contains the new optimized state.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently construction of clock limits gets skipped for diags.
This logic would be useful to get tested in diags.
[HOW]
Copy existing states to clk_table such that update_bw_bounding_box
logic gets used to fill the table.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.
[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.
This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Current pipe merge and split logic only supports cases where new
dc_state is allocated and relies on dc->current_state to gather
information from previous dc_state.
Calls to validate_bandwidth on UPDATE_TYPE_MED would cause an issue
because there is no new dc_state allocated, and data in
dc->current_state would be overwritten during pipe merge.
[how]
Only allow validate_bandwidth when new dc_state space is created.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The only usage of dcn21_res_pool_funcs is to assign its address to a
const pointer. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Implement an interface to obtain plane size caps
[How]
Add min_width, min_height fields to dc_plane_cap structure.
Set values to 16x16 for discrete ASICs, and 64x64 for others.
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn20_add_dsc_to_stream_resource is accessed in amdgpu_dm directly.
This creates build error for configuration with DCN disabled.
[How]
Make the function available through a resource pool function so
that dcn20 function need not be called directly.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP link layer CTS specs updated to change the test parameters in test
4.2.1.1.
Before it requires source to delay 400us on aux no reply.
With the specs updates Errata5, it requires source to delay 3.2ms
(based on LTTPR aux timeout)
This causes our test to fail after updating with the latest test
equipment firmware.
[how]
the change is to allow LTTPR 3.2ms aux timeout delay by default.
And set back to 400us if LTTPR feature is not enabled.
We will set 3.2ms and always enable LTTPR non transparent mode
if LTTPR feature is enabled and LTTPR is present.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DMUB command table should be allowed to be used
only if dmcu is explicitly disabled.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The change causes some regression in a common use case.
Will need more investigation before fixing the original issue.
[how]
This reverts commit fb8cf277b1.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SOC_BOUNDING_BOX_VALID is unused and not required for dcn21.
[How]
Remove it.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dal side nv12 wa has a lot of side effects.
KMD side wa is used, so this should be remove.
[How]
Removed wa from dal side.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Save the correct num vmid during resource creation and fix RN gpuvm
level from 1 to 16 vmid entries.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current locking scheme for cursor can result in a flip missing
its vsync, deferring it for one or more vsyncs. Result is a
potential for stuttering when cursor is moved.
[How]
Use cursor update lock so that flips are not blocked while cursor
is being programmed.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
modules/color calculates various colour operations which are translated
to abstracted HW. DCE 5-12 had almost no important changes, but
starting with DCN1, every new generation comes with fairly major
differences in color pipeline.
We would hack it with some DCN checks, but a better approach is to
abstract color pipe capabilities so modules/DM can decide mapping to
HW block based on logical capabilities,
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The downspread percentage was copied over from a previous version
of the display_mode_lib spreadsheet. This value has been updated,
and the previous value is too high to allow for such modes as
4K120hz. The new value is sufficient for such modes.
[HOW]
Update the value in dcn21_resource to match the spreadsheet.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently RN SOC bounding box update assumes we will get at least
2 clock states from SMU. This isn't always true and because of special
casing on first clock state we end up with low disp, dpp, dsc and phy
clocks.
This change removes the special casing allowing the first state to
acquire correct clocks.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
it doesn't represent panel specifically, it's more like the control
logic for the panel
[How]
change from panel to panel cntl to make it a bit more clear
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
panel power sequencer is currently just sitting in hwseq but it really
it tied to internal panels
[How]
make a new panel struct to contain power sequencer code
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
Renoir's pipe VM flags are not correctly updated if pipe strategy has
changed during some scenarios. It will result in watermarks mistakenly
calculation, thus underflow and garbage appear.
[How]:
Correctly update pipe VM flags to pipes which have been populated.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When dmcub is the default we no longer wish to create the psr and dmcu
objects. Currently a dc debug flag is used to implement this, but these
flags aren't populated until after dcn21_resource_construct is called.
This means the dmcub objects will never be created. Therefore we must
use a dc config flag, which is populated before dc resource construct.
[How]
Add a dc config flag.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML expects num_states to exclude the duplicate state.
[How]
Set num_states to correct value to prevent array off-by-one error. Also
refactor max clock level code for diags.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
P010 pixel format is not declared as supported in DRM and DM.
[How]
Add P010 format to the support list presented to DRM and checked in DM
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable/disable psr on dmcub and fallback to dmcu
when necessary.
[How]
Use dc config option to do so.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The default value for disable_dmcu is true, even for asics that require
dmcu.
[How]
Set flag properly per asic.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
vstartup calculation is incorrect due to use 2 number of cursors and
result in an underflow when playing video in full screen mode and
combines graphic plane and video plane.
[How]
Apply new policy for dml calculation.
1 cursor for graphic plane, 0 cursor for video plane.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Freesync borderless is not meant to be enabled on any APUs
[HOW]
Add is_apu cap to dcn21_resource_construct for correct recognition
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we have single channel memory, we can not light up 2 4k displays
with a 1080p edp, because we don't have enough bw by a small margin.
this small margin comes from dcc meta being too large. We however don't
have this dcc meta when we create fake planes so, before the flip we
will not filter out the mode for 2 4k displays with a 1080p edp
[how]
Change get_default_swizzle_mode to something more general so we don't
end up with a separate function for every missing field in the fake
plane. Add a reasonable dcc meta to the fake plane when it is filled in,
so we filter out modes that don't have enough bandwidth. To do this, we
take the screen width and align it to 1024(8k 60)
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some asics don't support FEC but FEC overhead is added into link
bandwidth calculation by mistake. This causes certain timing cannot be
validated.
[how]
Only include FEC overhead if both asic and display support FEC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Move psr_on_dmub flag from dc_debug_options to dc_config.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when changing display clock, SMU need to use power up DFS and use
DENTIST to ramp DFS DID to switch target frequency before switching back
to bypass.
[How]
fixed the minimum display clock to 100MHz, it's W/A the same with PCO.
Signed-off-by: Yu-ting Shen <Yu-ting.Shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow sometimes occurs during transition into MPO with stutter
enabled.
[How]
When transitioning into MPO, disable stutter. Re-enable stutter within
one frame.
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Add infrastructure to enable and disable PSR on DMCUB.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous logic is only good for 15W parts. Other configuration
need a smarter logic to match clk levels with pp table in the fuse.
[How]
Cache all 8 DPM level's clock data, find lvl that match each pstate
in the pp table and build input into DML base on that
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MPO isn't enabled on some 4k videos due to video source width is 4096
and the current limit is 3840.
[How]
Changed the limit to 4096.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
