[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The I2C memory blocks should be powered down when they are not in use.
This will reduce power consumption.
[How]
1. Write to I2C_LIGHT_SLEEP_FORCE to put memory in light sleep when
released
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust the FP handling to avoid nested calls.
The nested calls cause the warning below
WARNING: CPU: 3 PID: 384 at arch/x86/kernel/fpu/core.c:129 kernel_fpu_begin
Fixes: 582e2ce5b4 ("drm/amdgpu/display: FP fixes for DCN3.x (v4)")
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When mpo enabled, video comes is 709. Desktop use sRGB.
So color change easily noticeable especially when switch between
mpo/non-mpo.
[How]
Force use sRGB for video TF is sRGB or BT709.
DCN1/DCN2 use predefined type with YUV.
DCN3 use distributed points type with YUV.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the freesync power optimization increasing vtotal, the driver
believes that MPO is supported. MPO is turned on. Freesync then
exits, MPO can no longer be supported and immediate flip fails. This
causes corruption on the panel.
[How]
Avoid the freesync optimization when doing validation so in the case
freesync exits, driver can still support the configuration.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add proper FP_START/END handling and adjust Makefiles per
previous asics.
v2: fix up harder.
v3: fix clkmgr Makefile for dcn30
v4: fix old gcc handling is only required for x86
Build-tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com> (v1)
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need this to pass dp compliance.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nikola Cornij <nikola.cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All DCN3x resources share ABM_MASK_SH_LIST_DCN301 definition.
The naming is misleading since it looks like DCN30 code
depends on next version DCN301, which in fact is vice-versa.
[How]
Refactor the naming to ABM_MASK_SH_LIST_DCN30.
v2: squash in build fixes (Alex)
Signed-off-by: Roman Li <roman.li@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
missing OEM data to control graphics card functions
how:
load it into init_data. copied over from dcn2 implementation.
copied destruction sequence as well.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If full pstate is not supported, we should set WM set A
to 0 to prevent any hangs
[How]
If pstate is not supported, set watermark set A to 0
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some sink devices wish to have access to the minimum
HBlank supported by the ASIC.
[How]
Make the ASIC minimum HBlank available in Source
Device information address 0x340.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Enable ODM Combine + Fullscreen MPO on DCN2.1
For lower power consumption in video use cases.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable Memory Access at Last Level (MALL) feature for display.
v2: squash in 64 bit division fixes
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.
[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.
This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add code to gracefuly handle any pipe reassignment
occuring on dcn3 hardware. This should only happen when new
surfaces are used for an update rather than old ones updated.
Fixes: 69fc1f4b97 ("amd/drm/display: avoid dcn3 on flip opp change for slave pipes")
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
At the moment on flip opp reassignment does not work in all cases
for non root pipes.
This change simply makes sure we prefer pipes not used previously
when splitting in dcn3.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Eric Bernstein <eric.bernstein@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, when full p-state changes are not supported, DLG parameters
are calculated for no p-state support at all. However, we are required
to always support dummy p-state changes, so we should instead calculate
DLG based on dummy p-state latency when full p-state is unsupported.
This behaviour already exists for DCN2.
[How]
- move DLG calculation inside WM calculation
- if p-state unsupported, do not recalculate for set A, instead copy from
set C, and perform DLG calculation with dummy p-state latency
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some SOC BB paramters may vary per SKU, and it does
not make sense for driver to hardcode these values
[how]
Parse the values from VBIOS if available, and use
them if valid
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
some functions may need be dependent on stutter period in the future
how:
Extract from stutter calculations and place into perf_params structure
Signed-off-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR needs to be enabled on DCN30. This is the driver part of PSR
enablement.
Also disabled retired DMCU on driver side, since DMCU is
not supported on DCN30 anymore.
[How]
Add necessary changes to enable PSR on DCN30.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dpcs reg are missing for dcn3 link encoder regs list, so add them.
Also remove
DPCSTX_DEBUG_CONFIG and RDPCSTX_DEBUG_CONFIG as they are unused and
cause compile errors for dcn3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without this, enabling dsc will cause a nullptr
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Programming is missing the sequence where for eDP the scrambling is
reset when testing for eye diagram test pattern.
[How]
Include the required register in the definition
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Register definitions are asic-specific, so functions that use registers of
a particular asic should be static, to be exposed in asic-specific function
pointer structures.
[How]
- make register-definition-using functions static
- make some functions non-static, for future use
- remove duplicate function definition
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The only usage of dcn30_res_pool_funcs is to assign its address to a
const pointer. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our validation is a known mess with actual validation mixed with
topology configuration. This change makes sure topolgical validation is
completed before any topology changes are made so we do not run into
issues where we merge and split a pipe over the course of a single call.
v2: Squash in compilation fix
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update each p-state in the bounding box
[How]
Update states when assigning values to clocks
v2: squash in patch to set min values (Alex)
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to update the bounding box to have more granular control of the
DCFCLK.
[How]
Setup DCFCLK to use STA values and also optimal values based on
UCLK.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Get the values from VBIOS table
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
struct gpu_info_voltage_scaling_v1_0 & gpu_info_soc_bounding_box_v1_0 is
defined in amdgpu_socbb.h
Signed-off-by: Flora Cui <flora.cui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was done already done for other DCN blocks.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for managing resources for DCN3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
