When checking the PHY for status, by specification, the driver
should be using "topology" mode when querying the module type.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, VF devices can be deactivated while a message is
in-flight. In that case, a series of scary error message will be
printed in the log. Since these are actually harmless, check for this
case and suppress them. No harm, no foul.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current flag name of "enable-fw-lldp" is a bit cumbersome.
Change priv-flag name to "fw-lldp-agent" with a value of on or
off. This is more straight-forward in meaning.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The virtchnl interface provides a mechanism for a VF driver to request
head writeback support. This feature is deprecated as of AVF 1.0, but
older versions of a VF driver may still attempt to request the mode.
Since the ice hardware does not support head writeback, we should not
accept Tx queue configuration which attempts to enable it.
Currently, the driver simply assumes that the headwb_enabled bit will
never be set.
If a VF driver does request head writeback, the configuration will
return successfully, even though head writeback is not enabled. This
leaves the VF driver in a non functional state since it is assuming to
be operating in head writeback mode.
Fix the PF driver to reject any attempt to setup headwb_enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In rebuild DCB desired_dcbx_cfg was copy to local_dcbx_cfg, but
if DCBX mode is IEEE desired_dcbx_cfg is not initialized by DCBX
config from FW. Change logic to copy config value only if mode is
set to CEE.
If driver copy desired_dcbx_cfg to local_dcbx_cfg in IEEE mode there
is problem with globr. System is frozen after two or more globr.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a port is not cabled, but DCBx is enabled in the
firmware, the status of DCBx will be NOT_STARTED. This
is a valid state for FW enabled and should not be
treated as a is_fw_lldp true automatically.
Add the code to treat NOT_STARTED as another valid state.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we will call synchronize_irq() from the host for VF's. This is
not correct, so don't allow it.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, only the DCBx status is taken into account to
determine if FW LLDP is possible. But there are NVM version
coming out with DCBx enabled, and FW LLDP disabled. This
is causing errors where the driver sees that DCBx is not
disabled, and then tries to register for LLDP MIB change
events, and fails.
Change the logic to detect both DCBx and LLDP states in the
FW engine.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For control packets (i.e. LLDP packets) to be able to egress
from the main VSI, a bit has to be set in the TX_descriptor.
This should only be done for the main VSI and only if the
FW LLDP agent is disabled. A bit to allow this also has to
be set in the VSI context.
Add the logic to add the necessary bits in the VSI context
for the PF_VSI and the TX_descriptors for control packets
egressing the PF_VSI.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a bug where driver was breaking out of the loop and
reporting an error without retrying first.
Signed-off-by: Marcin Formela <marcin.formela@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a function to read NVM module data and uses it to
read current LLDP agent configuration from NVM API version 1.8.
Signed-off-by: Sylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver waits after issuing a reset. When a reset takes too long a driver
gives up. Implemented by invoking PF reset in a loop. After defined
number of unsuccessful PF reset trials it returns error.
Without this patch PF reset fails when NIC is in recovery mode.
So make i40e_set_mac_type() public. i40e driver requires i40e_set_mac_type()
to be public. It is required for recovery mode handling. Without this patch
recovery mode could not be detected in i40e_probe().
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes function i40e_update_dcb_config(). Instead of
i40e_update_dcb_config() we use i40e_init_dcb(), which implements the
correct NVM read.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add update to the VSI pointer passed to the i40e_set_vf_mac function.
If VF is in reset state the driver waits in i40e_set_vf_mac function
for the reset to be complete, yet after reset the vsi pointer
that was passed into this function is no longer valid.
The patch updates local VSI pointer directly from pf->vsi array,
by using the id stored in VF pointer (lan_vsi_idx).
Without this commit the driver might occasionally invoke general
protection fault in kernel and disable the OS entirely.
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The stats structure for the VEB switch statistics is reset periodically,
but the tc_stats are not reset at the same time.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Upcoming FW increment API version to 1.9 due to Extend PHY access AQ
command support. SW is ready for that support as well.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function check_recovery_mode had wrong if statement.
Now we check proper FWS1B register values, which are responsible for
the recovery mode. Recovery mode has 4 values for x710 and 2 for x722.
That's why we need 6 different flags which are defined in the code.
Now in the if statement, we recognize type of mac address
and register value.
Without those changes driver could show wrong state.
Signed-off-by: Adrian Podlawski <adrian.podlawski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds "drop mode" parameter to set mac config AQ command.
This bit controls the behavior when a no-drop packet is blocking a TC
queue.
0 – The PF driver is notified.
1 – The blocking packet is dropped and then the PF driver is notified.
Signed-off-by: Sylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes following error reported by cppcheck:
(error) Shifting signed 32-bit value by 31 bits is undefined behaviour
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When i40e_configure_tx_ring(vsi->tx_rings[i]) returns an error, we should
exit from i40e_vsi_configure_tx and return the error, instead of continuing
to check whether xdp is enable, and configure the xdp transmit ring.
Signed-off-by: huhai <huhai@kylinos.cn>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to the ixgbe issue fixed in:
655c914145 ("ixgbe: Check DDM existence in transceiver before access)
i40e has the same issue when reading eeprom from SFP's module that comply
with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM)
interface described in it. The existence of such area is specified by bit
6 of byte 92, set to 1 if implemented.
Without this patch, due to not checking this bit i40e fails to read SFP
module's eeprom with the follow message:
ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error
Because it fails to read the additional 256 bytes in which it was assumed
to exist the DDM data.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The functions i40e_aq_get_phy_abilities_resp() and i40e_set_fc() both
have giant structure on the stack, which makes each one use stack frames
larger than 500 bytes.
As clang decides one function into the other, we get a warning for
exceeding the frame size limit on 32-bit architectures:
drivers/net/ethernet/intel/i40e/i40e_common.c:1654:23: error: stack frame size of 1116 bytes in function 'i40e_set_fc' [-Werror,-Wframe-larger-than=]
When building with gcc, the inlining does not happen, but i40e_set_fc()
calls i40e_aq_get_phy_abilities_resp() anyway, so they add up on the
kernel stack just as much.
The parts that actually use large stacks don't overlap, so make sure
each one is a separate function, and mark them as noinline_for_stack to
prevent the compilers from combining them again.
Fixes: 0a862b43ac ("i40e/i40evf: Add module_types and update_link_info")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we fail to add/delete MAC filters in the VF, the print doesn't
distinguish between the two. Fix that by printing whether or not we
failed to add/delete the MAC filter respectively.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These queue variables are being assigned values that are type u16.
Change the local variables to match these types. Since these
represent queue counts, they should never be negative.
Signed-off-by: Pawel Kaminski <pawel.kaminski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to use some of the VF resources definition in the SR-IOV specific
virtchnl header file, this patch moves applicable code to
ice_virtchnl_pf.h file accordingly... and they should have been defined in
the destination file originally.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we use the ICE_MBXQ_LEN for both the Mailbox send and receive
queues that are used to communicate with VFs. This is fine for the send
queue because the PF driver will lock the queue for every single send,
but for the Mailbox receive queue every VF is posting to its Mailbox
send queue and the hardware is then handing the message to the PF on its
Mailbox receive queue. This becomes a problem with many VFs because it
seems to overburden the Mailbox receive queue on the PF. Fix this by
increasing the Mailbox receive queue for the PF to 512 entries.
The number 512 was determined based on the number of VFs supported by
the device. We can have a total of 256 VFs so in the worst case this
allows the VFs to put 2 messages in the PFs Mailbox receive queue at the
same time.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently there are a couple places where the VF is waiting too long when
checking the status of registers. This is causing the AVF driver to
spin for longer than necessary in the __IAVF_STARTUP state. Sometimes
it causes the AVF to go into the __IAVF_COMM_FAILED, which may retrigger
the __IAVF_STARTUP state. Try to reduce the chance of this happening by
removing unnecessary wait times in VF bringup/resets.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Register access for GLINT_DYN_CTL and GLINT_VECT2FUNC should be within
the PF space and not the absolute device space.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During rebuild ice_ena_vsi() is called to recover the VSI state.
This function assumes the PF VSI is always to be enabled, however,
it's possible that during reset/rebuild the interface can be
brought down. If this occurs, we can attempt to bring up the PF
VSI on a downed interface which can lead to various crashes. If
the interface is not running, do not bring up the associated VSI.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, the hardware will hand us a receive descriptor
which has no data attached, but is otherwise valid. The receive code was
improperly ignoring these descriptors, which result in an infinite loop.
To fix this, change the receive code to process all descriptors,
regardless of the size of the associated data. Add checks to the
memory-handling functions to allow for zero size.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the set local MIB AQ call failures in the DCB rebuild path
by setting the defaults for the ETS recommended DCB configuration. Also,
willing bits for the DCB configuration needs to be set correctly. Resets
works fine in IEEE mode as the ETS recommended DCB configuration is
populated but not in CEE mode.
Without this patch, PFR causes the kernel hang in CEE mode.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when busy polling is enabled we aren't setting/enabling
WB_ON_ITR in the driver. This doesn't break the driver, but it does
cause issues. If we don't enable WB_ON_ITR mode we will still get
write-backs from hardware during polling when a cache line has been
filled, but if a cache line is not filled we will not get the
write-back because WB_ON_ITR is not set. Fix this by enabling
WB_ON_ITR in the driver when interrupts are disabled.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When ETHTOOL_GLINKSETTINGS is defined get pause param pause->autoneg
reports SW configured setting, however when not defined get pause param
pause->autoneg reports the link status. Set pause param needs to compare
pause->autoneg with the same source as get pause param to block the user
from changing autoneg with the set pause param option, or the user
may be incorrectly blocked from changing Rx|Tx pause settings.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch restructures how VFs are configured, and resources allocated.
Instead of freeing resources that were never allocated, and resetting
empty VFs that have never been created - the new flow will just allocate
resources for number of requested VFs based on the availability.
During VFs initialization process, global interrupt is disabled, and
rearmed after getting MSIX vectors for VFs. This allows immediate mailbox
communications, instead of delaying it till later and VFs.
PF communications resulted to using polling instead of actual interrupt.
The issue manifested when creating higher number of VFs (128 VFs) per PF.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we divide budget by the number of Rx queues per Rx ring
container in ice_napi_poll even if there is only 1. This is an
unnecessary divide for the normal case of 1 Rx ring per Rx ring
container. Fix this by using an unlikely() call in the case where we
actually need to divide.
Also, we will always set budget_per_ring even if there are no Rx rings
in the Rx ring container so we don't need to initialize it to 0.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently in ice_get_tx_pending we try to read a Tx ring's tail. This is
then compared with the software based head (next_to_clean) to determine
if we have pending work. This will never work because reading of the Tx
ring's tail is no longer supported. Fix this by using the software based
tail (next_to_use) to determine if there is pending work.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the need_wakeup feature of AF_XDP. If the
application has told the kernel that it might sleep using the new bind
flag XDP_USE_NEED_WAKEUP, the driver will then set this flag if it has
no more buffers on the NIC Rx ring and yield to the application. For
Tx, it will set the flag if it has no outstanding Tx completion
interrupts and return to the application.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch adds support for the need_wakeup feature of AF_XDP. If the
application has told the kernel that it might sleep using the new bind
flag XDP_USE_NEED_WAKEUP, the driver will then set this flag if it has
no more buffers on the NIC Rx ring and yield to the application. For
Tx, it will set the flag if it has no outstanding Tx completion
interrupts and return to the application.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This commit replaces ndo_xsk_async_xmit with ndo_xsk_wakeup. This new
ndo provides the same functionality as before but with the addition of
a new flags field that is used to specifiy if Rx, Tx or both should be
woken up. The previous ndo only woke up Tx, as implied by the
name. The i40e and ixgbe drivers (which are all the supported ones)
are updated with this new interface.
This new ndo will be used by the new need_wakeup functionality of XDP
sockets that need to be able to wake up both Rx and Tx driver
processing.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_service_task() calls unregister_netdev() under rtnl_lock().
But unregister_netdev() internally calls rtnl_lock().
So deadlock would occur.
Fixes: 59dd45d550 ("ixgbe: firmware recovery mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2019-08-05
This series contains updates to i40e driver only.
Dmitrii adds missing statistic counters for VEB and VEB TC's.
Slawomir adds support for logging the "Disable Firmware LLDP" flag
option and its current status.
Jake fixes an issue where VF's being notified of their link status
before their queues are enabled which was causing issues. So always
report link status down when the VF queues are not enabled. Also adds
future proofing when statistics are added or removed by adding checks to
ensure the data pointer for the strings lines up with the expected
statistics count.
Czeslaw fixes the advertised mode reported in ethtool for FEC, where the
"None BaseR RS" was always being displayed no matter what the mode it
was in. Also added logging information when the PF is entering or
leaving "allmulti" (or promiscuous) mode. Fixed up the logging logic
for VF's when leaving multicast mode to not include unicast as well.
v2: drop Aleksandr's patch (previously patch #2 in the series) to
display the VF MAC address that is set by the VF while community
feedback is addressed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unicast log when VF is leaving multicast mode.
Added check of vf->vf_states &
I40E_VF_STATE_MC_PROMISC/I40E_VF_STATE_UC_PROMISC.
Without this commit, leaving multicast mode logs "unset unicast"
in dmsg.
Signed-off-by: Czeslaw Zagorski <czeslawx.zagorski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to i40e_get_ethtool_stats, add a goto to verify that the data
pointer for the strings lines up with the expected stats count. This
helps ensure that bugs are not introduced when adding stats.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add log when PF is entering and leaving allmulti mode. The
change of PF state is visible in dmesg now. Without this commit,
entering and leaving allmulti mode is not logged in dmesg.
Signed-off-by: Czeslaw Zagorski <czeslawx.zagorski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Updates visual effect for advertised mode after setting desired mode.
The mode appears in advertised FEC mode correctly, when ethtool
interface command is called. Without this commit advertised FEC
is displayed regardless of the settings as "None BaseR RS".
Signed-off-by: Czeslaw Zagorski <czeslawx.zagorski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
