It's recommended to disable VDD4BLOW during initialisation.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-6-git-send-email-kvalo@codeaurora.org
For QCA6390, one PCI related clock drifts sometimes, and
it makes PCI link difficult to quit L1ss. Fix it by writing
some registers which are known to fix the problem.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-5-git-send-email-kvalo@codeaurora.org
For QCA6390, host needs to reset some registers before MHI power up to fix PCI
link unstable issue if hot reset happened. Also clear all pending interrupts
during power up.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-4-git-send-email-kvalo@codeaurora.org
In QCN9074 ath11k boot, firmware crash is observed in 64-bit
builds and is due to wrong 64 bit MSI address size. This patch
fixes the firmware crash. Read msi high addr if 64-bit addresses
allowed on MSI.
Tested-On: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606199334-18206-1-git-send-email-akolli@codeaurora.org
For QCA6390, host can read and write registers below unwindowed
address directly without programming the window register. For
registers below bar0 + 4k - 32, host can read and write regardless
of the power save state. Shadow registers are located below
bar0 + 4K - 32.
Before MHI power up, there is no need to wakeup MHI so ini_done is
added to indicate it.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-2-git-send-email-kvalo@codeaurora.org
For QCA6390, normal power up and power down can't bring MHI
to a workable state. This happens especially in warm reboot
and rmmod and insmod. Host needs to write a few registers to
bring MHI to normal state.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeauroro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-10-git-send-email-kvalo@codeaurora.org
Modem Host Interface (MHI) is a communication protocol to communicate with
external Qualcomm modems and Wi-Fi chipsets over high speed peripheral buses.
Even though MHI doesn’t dictate underlying physical layer, protocol and MHI
stack is structured for PCI based devices.
Register directly with MHI subsystem as a MHI device driver for firmware
download to QCA6390.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-9-git-send-email-kvalo@codeaurora.org
Add support for setting up pci region and dma mask.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-6-git-send-email-kvalo@codeaurora.org
