Make sure the number of WBM_IDLE_LINK ring descriptors is power
of 2. This increases the number of descriptors to 32k from the
current ~18k to fix the target assert because of the shortage in
the descriptors in WBM_IDLE_LINK ring. Remove unnecessary
power of 2 calculation in ath11k_dp_link_desc_setup() as it is
not required after this change.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV length was 0 for TLV tag 'WMI_TAG_ARRAY_STRUCT' causing
Q6 to crash when trying to configure pktlog filter via debugfs.
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
skb_panic is hit during msdu coalescing whenever
enough tailroom is not allocated based on the remaining
msdu length which is spread across in different rx buffers.
Compute the extra length for resizing the skb based on
the total msdu length and the msdu length of the first buffer.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
remove unused counter to avoid taking locks inorder to optimize
cpu load.
Using Flamegraph, cpu usage of ath11k_dp_tx() observed to be decreased
from 5.58% to 3.74% with iperf traffic running with 80MHz bandwidth ap
mode.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In conf_tx() mac operation callback, we are truncating the tx
params cw_min and cw_max due to lower data type cast. so modified
the data type of cwmin and cwmax to avoid the trucation issue.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch drops ath11k_hal_rx_parse_dst_ring_desc(). This function was
creating a huge amount of load, which lead to a signifcant latency delay
when processing data in the RX path.
Pegging the processing on a specific core and running perf --top we get
the following output when running HE80 at a fixed bandwidth of 1gbit.
with patch
19.19% [ath11k] [k] ath11k_dp_process_rx
5.02% [ath11k] [k] ath11k_dp_rx_tid_del_func
4.39% [kernel] [k] v7_dma_inv_range
4.15% [kernel] [k] __slab_alloc.constprop.1
4.03% [kernel] [k] dev_gro_receive
3.86% [kernel] [k] tcp_gro_receive
3.07% [ip_tables] [k] ipt_do_table
2.96% [kernel] [k] dma_cache_maint_page
without patch
21.64% [ath11k] [k] ath11k_hal_rx_parse_dst_ring_desc
10.80% [ath11k] [k] ath11k_dp_process_rx
3.77% [kernel] [k] v7_dma_inv_range
3.48% [kernel] [k] dev_gro_receive
3.32% [ath11k] [k] ath11k_dp_rx_tid_del_func
3.17% [mac80211] [k] ieee80211_rx_napi
2.70% [kernel] [k] dma_cache_maint_page
2.65% [mac80211] [k] ieee80211_sta_ps_transition
When removing the the bandwidth limit and rerunning the test we see an
overall throughput improvement of 3-400mbit when running 4x4 HE80.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is observed that ath11k STA mode UL throughput is low.
This is due to packets delivered to FW from TCL instead of TQM.
TCL AST search fail causes packet delivered to FW, fix this by
properly configuring the TCL address search type and ast_hash.
STA UL throughput is improved 10times with 11AC AP.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current ath11k driver failed to parse
wmi_tlv_svc_rdy_ext_parse if there is change in
wmi_mac_phy_capabilities length with below error.
ath11k c000000.wifi1: failed to extract mac caps, idx :0
ath11k c000000.wifi1: failed to parse tlv -22
This is needed to get firmware version
WLAN.HK.2.0.0.1-00240-QCAHKSWPL_SILICONZ-1 working.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Handled the error case with proper resource cleanup and
moved the handling into a separate function from
ath11k_mac_sta_state.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Previous configuartion of htt stats sounding info and pdev cca stats
are invalid due to that getting time out error.
Changing htt stats sounding info value from 0xFF to 0x00 and htt pdev cca
stats from 0x10 to 0x00
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trigger the WMI call en/disabling OBSS PD when the bss config changes or we
assoc to an AP that broadcasts the IE.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add target wait time wmi calls to the driver. En/disable the support
from when the bss_config changes. We ignore the cmd completion events.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add basic HE support to the driver. The sband_iftype data is generated from
the capabilities read from the FW.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove unexecuted code while handling amsdu packets.
The same logic is done before calling ath11k_dp_rx_msdu_coalesce
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX rate stats for the retried packets for a station comes through
tx completion events. Assigning hw reported bandwidth information
directly to station's txrate bandwidth will cause below warning.
Fix this warning by converting the hw reported bandwidth to
mac80211 base bandwidth.
[ 134.758190] PC is at cfg80211_calculate_bitrate+0x1bc/0x214 [cfg80211]
[ 134.765730] LR is at cfg80211_calculate_bitrate+0x1bc/0x214 [cfg80211]
[ 134.875014] [<ffffffbffca8d708>] cfg80211_calculate_bitrate+0x1bc/0x214 [cfg80211]
[ 134.877192] [<ffffffbffcaa9704>] nl80211_put_sta_rate+0x54/0xf24 [cfg80211]
[ 134.884829] [<ffffffbffcaa9d48>] nl80211_put_sta_rate+0x698/0xf24 [cfg80211]
[ 134.891687] [<ffffffbffcaaa490>] nl80211_put_sta_rate+0xde0/0xf24 [cfg80211]
[ 134.898975] [<ffffffc0004de748>] genl_lock_dumpit+0x30/0x4c
[ 134.905998] [<ffffffc0004dc264>] netlink_dump+0xf4/0x248
[ 134.911291] [<ffffffc0004dc910>] __netlink_dump_start+0xe0/0x174
[ 134.916850] [<ffffffc0004df114>] genl_family_rcv_msg+0x130/0x2c0
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We can regularly see the following message.
- "ath11k c000000.wifi1: failed to find the peer with peer_id 4"
This happens when the FW starts sending stats for the peer whilst the
peer is not fully associated. Convert this info message to a debug one.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Everytime a new peer gets associated, we see the following message in the log
- ath11k c000000.wifi1: Unknown eventid: 0x6017
Ignore this event for now. We probably need to handle the event properly when
we add OMI support.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 expects the definition of what HE rate info is available inside a
struct prepended to the skb.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first
supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k
uses mac80211 and supports AP, Station and Mesh modes.
Even though ath11k has some similar code as with ath10k (especially
the WMI layer) it was concluded to be simpler to have a "clean start"
for ath11k code base and not try to share the code with ath10k. This
makes maintenance easier and avoids major changes in ath10k, which
would have significantly increased the risk of regressions in existing
setups.
Even though the driver is very similar with ath10k but there are major
differences as well. The datapath is completely different. ath11k
supports multiple MACs, called "soc" in the firmware interface. And
there's only one WMI interface to support.
Currently ath11k supports only IEEE 802.11ac mode, but patches for
802.11ax are available and they will be submitted after ath11k is
accepted to upstream.
The firmware images are available from ath11k-firmware repository but
they will be also submitted to linux-firmware:
https://github.com/kvalo/ath11k-firmware
This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1.
The driver has had multiple authors who are listed in alphabetical
order below.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
