Set I2C bus 7 to multi-master mode and add the panel device that will
register as a slave.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200908200101.64974-6-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Fix the VGA reserved memory node, and add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the second EHCI controller on the AST2600. Also add a line-name
for the GPIO that controls power to the USB port.
The power control is in place to allow the port to be disabled, for
those that are worried about rogue USB sticks.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier uses the P10 processor so the OCC binding should reflect that.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the four SPI masters on each CFAM. Each master has four 128KB EEPROM
devices attached to it.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adding pca9552 exposes the presence detect lines for the cards and
tca9554 exposes the presence details for the cards.
Signed-off-by: Jet Li <Jet.Li@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We have a 4-bus mux whose output is selected by two GPIO inputs. Wire it
up in the devicetree and ensure the output is enabled by hogging the
appropriate line.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
The signal is wired as active high on the first pass systems.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
GPIOP7 is used in the Rainier design to manage the state of a
microcontroller elsewhere in the system but its ball, Y23, is the
driver of the heartbeat LED on the ast2600-evb and the SoC defaults Y23
at power-on to the pulse-train behaviour used to drive the LED. This
causes much confusion for the micro in the Rainier system, so hog the
line as early as possible.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The hub FSI master can access the cfams on two other processors. Reflect
this by adding a second cfam to the first hub description.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Tested-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier uses GPIO B6 as the checkstop GPIO. Define the line-name
so that this GPIO can be found by name.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The BMC uses reserves the top 16MB of memory for the host to use for VGA
or PCIe communication.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Name the GPIOs to help userspace work with them. The names describe the
functionality the lines provide, not the net or ball name. This makes it
easier to share userspace code across different systems and makes the
use of the lines more obvious.
Signed-off-by: Andrew Geissler <geisonator@yahoo.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Regulators will be dynamically configured and monitored from userspace.
Signed-off-by: Matthew Barth <msbarth@linux.ibm.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the description of the Power CPUs that are attached to the
BMC.
Without this userspace will see the '/dev/scom66' style layout.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
All 16 pins of the PCA9552 at 7-bit address 0x61 should be set as type
GPIO.
Signed-off-by: Matthew Barth <msbarth@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The second VUART is used to expose multiplexed, non-hypervisor consoles.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Change Rainier device tree to use UCD90320 chip and only bind driver to
port which excepts PMBus commands.
Signed-off-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier can use either version of the IBM CFFPS, so don't set the
version in the devicetree so the driver can detect it automatically.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The PCA9552 used for fan fault and presence information is at address
61h, not 60h.
Fixes: 2efc118ce3 ("ARM: dts: aspeed: rainier: Add i2c devices")
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a revert of "ARM: dts: aspeed: rainier: Add i2c devices", which
was already applied to the tree.
Fixes: 9c44db7096 ("ARM: dts: aspeed: rainier: Add i2c devices")
Reviewed-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Tested-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add in a gpio-keys section to the Rainier device tree source, add in the
power supply presence GPIOs.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Fix the size of the Proc VRM card's eeprom used for vpd storage. The
size is changed from 64Kbit to 128Kbit.
Signed-off-by: Jinu Joy Thomas <jinu.joy.thomas@in.ibm.com>
Reviewed-by: Santosh Puranik <santosh.puranik.ibm@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Like most OpenPower machines the VUART is expected to be at /dev/ttyS5
for communication with the host over LPC.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Added eeproms for the below VPD devices
- BMC
- TPM
- System Planar
- DCM 0 VRM
- DCM 1 VRM
- Base Op panel
- Lcd Op panel
- DASD (All)
- PCIe Cards (All)
Signed-off-by: Jinu Joy Thomas <jinu.joy.thomas@in.ibm.com>
Reviewed-by: Santosh Puranik <santosh.puranik.ibm@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We need to ungate RCLK on AST2500- and AST2600-based platforms for RMII
to function. RMII interfaces are commonly used for NCSI.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add fan controllers, regulators, temperature sensors, power supplies
and regulators.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add fan controllers, regulators, temperature sensors, power supplies
and regulators.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier contains two NCSI network devices.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier is a new IBM server with POWER host processors and an AST2600
BMC.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
