because i2c is unstable in GPU reset, driver need protect
eeprom update from GPU reset, to not miss any bad page record.
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Restore RPS for ILK-M. We lost it when an extra HAS_RPS()
check appeared in intel_rps_enable().
Unfortunaltey this just makes the performance worse on my
ILK because intel_ips insists on limiting the GPU freq to
the minimum. If we don't do the RPS init then intel_ips will
not limit the frequency for whatever reason. Either it can't
get at some required information and thus makes wrong decisions,
or we mess up some weights/etc. and cause it to make the wrong
decisions when RPS init has been done, or the entire thing is
just wrong. Would require a bunch of reverse engineering to
figure out what's going on.
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 9c878557b1 ("drm/i915/gt: Use the RPM config register to determine clk frequencies")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021131443.25616-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The "mmio" writes into vgpu registers are simple memory traps from the
guest into the host. We do not need to assert in the guest that the
device is awake for the io as we do not write to the device itself.
However, over time we have refactored all the mmio accessors with the
result that the vgpu reuses the gen2 accessors and so inherits the
assert for runtime-pm of the native device. The assert though has
actually been there since commit 3be0bf5acc ("drm/i915: Create vGPU
specific MMIO operations to reduce traps").
References: 3be0bf5acc ("drm/i915: Create vGPU specific MMIO operations to reduce traps")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Yan Zhao <yan.y.zhao@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200811092532.13753-1-chris@chris-wilson.co.uk
(cherry picked from commit 0e65ce24a3)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
If i915.ko is being used as a passthrough device, it does not know if
the host is using intel_iommu. Mixing the iommu and gfx causes a few
issues (such as scanout overfetch) which we need to workaround inside
the driver, so if we detect we are running under a hypervisor, also
assume the device access is being virtualised.
Reported-by: Stefan Fritsch <sf@sfritsch.de>
Suggested-by: Stefan Fritsch <sf@sfritsch.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Stefan Fritsch <sf@sfritsch.de>
Cc: stable@vger.kernel.org
Tested-by: Stefan Fritsch <sf@sfritsch.de>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201019101523.4145-1-chris@chris-wilson.co.uk
(cherry picked from commit f566fdcd6c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The GPU is trashing the low pages of its reserved memory upon reset. If
we are using this memory for ringbuffers, then we will dutiful resubmit
the trashed rings after the reset causing further resets, and worse. We
must exclude this range from our own use. The value of 128KiB was found
by empirical measurement (and verified now with a selftest) on gen9.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201019165005.18128-2-chris@chris-wilson.co.uk
(cherry picked from commit d3606757e6)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In switching to using objects for our ppGTT scratch pages, care was not
taken to avoid trying to unref NULL objects on failure. And for gen6
ppGTT, it appears we forgot entirely to unwind after a partial allocation
failure.
Fixes: 89351925a4 ("drm/i915/gt: Switch to object allocations for page directories")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201019083444.1286-1-chris@chris-wilson.co.uk
(cherry picked from commit fa812ce96a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
GEN >= 10 hardware supports the programmable scaler filter.
Attach scaling filter property for CRTC and plane for GEN >= 10
hardwares and program scaler filter based on the selected filter
type.
changes since v3:
* None
changes since v2:
* Use updated functions
* Add ps_ctrl var to contain the full PS_CTRL register value (Ville)
* Duplicate the scaling filter in crtc and plane hw state (Ville)
changes since v1:
* None
Changes since RFC:
* Enable properties for GEN >= 10 platforms (Ville)
* Do not round off the crtc co-ordinate (Danial Stone, Ville)
* Add new functions to handle scaling filter setup (Ville)
* Remove coefficient set 0 hardcoding.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-5-pankaj.laxminarayan.bharadiya@intel.com
Integer scaling (IS) is a nearest-neighbor upscaling technique that
simply scales up the existing pixels by an integer
(i.e., whole number) multiplier.Nearest-neighbor (NN) interpolation
works by filling in the missing color values in the upscaled image
with that of the coordinate-mapped nearest source pixel value.
Both IS and NN preserve the clarity of the original image. Integer
scaling is particularly useful for pixel art games that rely on
sharp, blocky images to deliver their distinctive look.
Introduce functions to configure the scaler filter coefficients to
enable nearest-neighbor filtering.
Bspec: 49247
changes since v6:
* Trust compiler, remove pointless inline keyword from cnl_coef_tap()
& cnl_nearest_filter_coef() functions (Ville)
changes since v4:
* Make cnl_coef_tap(), cnl_nearest_filter_coef() inline (Uma)
changes since v3:
* None
changes since v2:
* Move APIs from 5/5 into this patch.
* Change filter programming related function names to cnl_*, move
filter select bits related code into inline function (Ville)
changes since v1:
* Rearrange skl_scaler_setup_nearest_neighbor_filter() to iterate the
registers directly instead of the phases and taps (Ville)
changes since RFC:
* Refine the skl_scaler_setup_nearest_neighbor_filter() logic (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-4-pankaj.laxminarayan.bharadiya@intel.com
Introduce scaler registers and bit fields needed to configure the
scaling filter in prgrammed mode and configure scaling filter
coefficients.
changes since v3:
* None
changes since v2:
* Change macro names to CNL_* and use +(set)*8 instead of adding
another trip through _PICK_EVEN (Ville).
changes since v1:
* None
changes since RFC:
* Parametrize scaler coeffient macros by 'set' (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-3-pankaj.laxminarayan.bharadiya@intel.com
Introduce per-plane and per-CRTC scaling filter properties to allow
userspace to select the driver's default scaling filter or
Nearest-neighbor(NN) filter for upscaling operations on CRTC and
plane.
Drivers can set up this property for a plane by calling
drm_plane_create_scaling_filter() and for a CRTC by calling
drm_crtc_create_scaling_filter().
NN filter works by filling in the missing color values in the upscaled
image with that of the coordinate-mapped nearest source pixel value.
NN filter for integer multiple scaling can be particularly useful for
for pixel art games that rely on sharp, blocky images to deliver their
distinctive look.
changes since: v6:
* Move property doc to existing "Standard CRTC Properties" and
"Plane Composition Properties" doc comments (Simon)
changes since v3:
* Refactor code, add new function for common code (Ville)
changes since v2:
* Create per-plane and per-CRTC scaling filter property (Ville)
changes since v1:
* None
changes since RFC:
* Add separate properties for plane and CRTC (Ville)
Link: https://github.com/xbmc/xbmc/pull/18194
Link: https://github.com/xbmc/xbmc/pull/18567
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Simon Ser <contact@emersion.fr>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-2-pankaj.laxminarayan.bharadiya@intel.com
This moves the to system move into the drivers, and moves all
the unbinds in the move path under driver control
Note: radeon/nouveau already wait so don't duplicate it.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020010319.1692445-4-airlied@gmail.com
No functional changes in this patch.
With Bigjoiner, there are 2 pipes driving 2 halfs of 1
transcoder. The transcoder_mode has the full timings, and is used
for configuring the transcoder with the intended mode after
joining the 2 halves.
To clear the confusion, we rename intel_set_pipe_timings to
intel_set_transcoder_timings
v2:
* Split the renaming into separate patch (Ville)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008214535.22942-2-manasi.d.navare@intel.com
Add ABGR format with 10-bit components packed in 64-bit per pixel.
This format can be used to handle
VK_FORMAT_R10X6G10X6B10X6A10X6_UNORM_4PACK16 on little-endian
architectures.
Signed-off-by: Matteo Franchin <matteo.franchin@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201012164043.23630-1-matteo.franchin@arm.com
Move the DSC stuff out from the middle of the ICP HPD register
definitions. The location seems to have been selected by a
dice roll.
SHPD_FILTER_CNT addition also went astray due to the DSC
mess, so we also fix that vs. ICP_TC_HPD_{SHORT,LONG}_DETECT().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201006143349.5561-2-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
i915:
- Set all unused color plane offsets to ~0xfff again (Ville)
- Fix TGL DKL PHY DP vswing handling (Ville)
amdgpu:
- DCN clang warning fix
- eDP fix
- BACO fix
- Kernel documentation fixes
- SMU7 mclk fix
- VCN1 hw bug workaround
amdkfd:
- kvfree vs kfree fix
-----BEGIN PGP SIGNATURE-----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=/+Vb
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-10-19' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Some fixes queued up already for i915 and amdgpu, I've also included
the fix for the clang warning you've seen.
i915:
- set all unused color plane offsets to ~0xfff again (Ville)
- fix TGL DKL PHY DP vswing handling (Ville)
amdgpu:
- DCN clang warning fix
- eDP fix
- BACO fix
- kernel documentation fixes
- SMU7 mclk fix
- VCN1 hw bug workaround
amdkfd:
- kvfree vs kfree fix"
* tag 'drm-next-2020-10-19' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Fix incorrect dsc force enable logic
drm/amdkfd: Use kvfree in destroy_crat_image
drm/amdgpu: vcn and jpeg ring synchronization
drm/amd/pm: increase mclk switch threshold to 200 us
docs: amdgpu: fix a warning when building the documentation
drm/amd/display: kernel-doc: document force_timing_sync
drm/amdgpu/swsmu: init the baco mutex in early_init
drm/amd/display: Fix module load hangs when connected to an eDP
drm/i915: Set all unused color plane offsets to ~0xfff again
drm/i915: Fix TGL DKL PHY DP vswing handling
Currently we call .hpd_irq_setup() directly just before display
resume, and follow it with another call via intel_hpd_init()
just afterwards. Assuming the hpd pins are marked as enabled
during the open-coded call these two things do exactly the
same thing (ie. enable HPD interrupts). Which even makes sense
since we definitely need working HPD interrupts for MST sideband
during the display resume.
So let's nuke the open-coded call and move the intel_hpd_init()
call earlier. However we need to leave the poll_init_work stuff
behind after the display resume as that will trigger display
detection while we're resuming. We don't want that trampling over
the display resume process. To make this a bit more symmetric
we turn this into a intel_hpd_poll_{enable,disable}() pair.
So we end up with the following transformation:
intel_hpd_poll_init() -> intel_hpd_poll_enable()
lone intel_hpd_init() -> intel_hpd_init()+intel_hpd_poll_disable()
.hpd_irq_setup()+resume+intel_hpd_init() -> intel_hpd_init()+resume+intel_hpd_poll_disable()
If we really would like to prevent all *long* HPD processing during
display resume we'd need some kind of software mechanism to simply
ignore all long HPDs. Currently we appear to have that just for
fbdev via ifbdev->hpd_suspended. Since we aren't exploding left and
right all the time I guess that's mostly sufficient.
For a bit of history on this, we first got a mechanism to block
hotplug processing during suspend in commit 15239099d7 ("drm/i915:
enable irqs earlier when resuming") on account of moving the irq enable
earlier. This then got removed in commit 50c3dc970a ("drm/fb-helper:
Fix hpd vs. initial config races") because the fdev initial config
got pushed to a later point. The second ad-hoc hpd_irq_setup() for
resume was added in commit 0e32b39cee ("drm/i915: add DP 1.2 MST
support (v0.7)") to be able to do MST sideband during the resume.
And finally we got a partial resurrection of the hpd blocking
mechanism in commit e8a8fedd57 ("drm/i915: Block fbdev HPD
processing during suspend"), but this time it only prevent fbdev
from handling hpd while resuming.
v2: Leave the poll_init_work behind
v3: Remove the extra intel_hpd_poll_disable() from display reset (Lyude)
Add the missing intel_hpd_poll_disable() to display init (Imre)
Cc: Lyude Paul <lyude@redhat.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201013181137.30560-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.
Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.
Trivial bits done with cocci:
@@
expression DP;
@@
(
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF)
+ intel_dp_set_power(DP, DP_SET_POWER_D3)
|
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON)
+ intel_dp_set_power(DP, DP_SET_POWER_D0)
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Rather that try to trick LSPCON back into PCON mode from the .reset()
hook let's just do that as a regular part of the normal modeset
sequence, which is going to take care of the system resume case. During
a normal modeset this should normally be a nop as the mode should have
already been switched by .detect().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The "mmio" writes into vgpu registers are simple memory traps from the
guest into the host. We do not need to assert in the guest that the
device is awake for the io as we do not write to the device itself.
However, over time we have refactored all the mmio accessors with the
result that the vgpu reuses the gen2 accessors and so inherits the
assert for runtime-pm of the native device. The assert though has
actually been there since commit 3be0bf5acc ("drm/i915: Create vGPU
specific MMIO operations to reduce traps").
References: 3be0bf5acc ("drm/i915: Create vGPU specific MMIO operations to reduce traps")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Yan Zhao <yan.y.zhao@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200811092532.13753-1-chris@chris-wilson.co.uk
If i915.ko is being used as a passthrough device, it does not know if
the host is using intel_iommu. Mixing the iommu and gfx causes a few
issues (such as scanout overfetch) which we need to workaround inside
the driver, so if we detect we are running under a hypervisor, also
assume the device access is being virtualised.
Reported-by: Stefan Fritsch <sf@sfritsch.de>
Suggested-by: Stefan Fritsch <sf@sfritsch.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Stefan Fritsch <sf@sfritsch.de>
Cc: stable@vger.kernel.org
Tested-by: Stefan Fritsch <sf@sfritsch.de>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201019101523.4145-1-chris@chris-wilson.co.uk
Hooray for generic fbdev support, making this a oneliner. We just
needed to fix preferred_depth fixed and the vmap support added first.
This is useful for testing fbdev testcases in igt. Right now we only
have a simple one in the fbdev testcases, which passes both info and
mmap subtests.
v2: Augment commit message as suggested by Melissa.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Melissa Wen <melissa.srw@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Cc: Melissa Wen <melissa.srw@gmail.com>
Cc: Haneen Mohammed <hamohammed.sa@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201009232156.3916879-3-daniel.vetter@ffwll.ch
Underruns happens when plane height + y offset is not a modulo of 4
when FBC is enabled. It happens when scanline is at vactive - 10 but
that is not feasible to do from the software side so here completely
disabling FBC when height + y offset matches to avoid visual glitches.
Specification says that it only affects TGL display C stepping and
newer but to simply the check and as TGL is already in final costumers
hands, pre-production display stepping A and B was also included.
BSpec: 52887 ICL
BSpec: 52888 EHL/JSL
BSpec: 52890/55378 TGL
BSpec: 53508 DG1
BSpec: 53273 RKL
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201019175609.28715-1-jose.souza@intel.com
This sequence is not part of "Sequences to Initialize Display" but
as noted in the MBus page the DBUF_CTL.Tracker_state_service needs
to be set to 8.
BSpec: 49213
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201019173906.18892-1-jose.souza@intel.com
In all 3 drivers there is a case where the driver knows the
bo is in SYSTEM so don't call the api that checks that.
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201019071314.1671485-4-airlied@gmail.com
On Tigerlake, we are seeing a repeat of commit d8f5053117 ("drm/i915/icl:
Forcibly evict stale csb entries") where, presumably, due to a missing
Global Observation Point synchronisation, the write pointer of the CSB
ringbuffer is updated _prior_ to the contents of the ringbuffer. That is
we see the GPU report more context-switch entries for us to parse, but
those entries have not been written, leading us to process stale events,
and eventually report a hung GPU.
However, this effect appears to be much more severe than we previously
saw on Icelake (though it might be best if we try the same approach
there as well and measure), and Bruce suggested the good idea of resetting
the CSB entry after use so that we can detect when it has been updated by
the GPU. By instrumenting how long that may be, we can set a reliable
upper bound for how long we should wait for:
513 late, avg of 61 retries (590 ns), max of 1061 retries (10099 ns)
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2045
References: d8f5053117 ("drm/i915/icl: Forcibly evict stale csb entries")
References: HSDES#22011327657, HSDES#1508287568
Suggested-by: Bruce Chang <yu.bruce.chang@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Bruce Chang <yu.bruce.chang@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: stable@vger.kernel.org # v5.4
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200915134923.30088-2-chris@chris-wilson.co.uk
(cherry picked from commit 233c1ae3c8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
A CSB entry is 64b, and it is simpler for us to treat it as an array of
64b entries than as an array of pairs of 32b entries.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200915134923.30088-1-chris@chris-wilson.co.uk
(cherry picked from commit f24a44e52f)
(cherry picked from commit 3d4dbe0e0f0d04ebcea917b7279586817da8cf46)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We may try to preempt the currently executing request, only to find that
after unravelling all the dependencies that the original executing
context is still the earliest in the topological sort and re-submitted
back to HW (if we do detect some change in the ELSP that requires
re-submission). However, due to the way we check for wrap-around during
the unravelling, we mark any context that has been submitted just once
(i.e. with the rq->wa_tail set, but the ring->tail earlier) as
potentially wrapping and requiring a forced restore on resubmission.
This was expected to be not a problem, as it was anticipated that most
unwinding for preemption would result in a context switch and the few
that did not would be lost in the noise. It did not take long for
someone to find one particular workload where the cost of those extra
context restores was measurable.
However, since we know the wa_tail is of fixed size, and we know that a
request must be larger than the wa_tail itself, we can safely maintain
the check for request wrapping and check against a slightly future point
in the ring that includes an expected wa_tail. (That is if the
ring->tail is already set to rq->wa_tail, including another 8 bytes in
the check does not invalidate the incremental wrap detection.)
Fixes: 8ab3a3812a ("drm/i915/gt: Incrementally check for rewinding")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Bruce Chang <yu.bruce.chang@intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002083425.4605-1-chris@chris-wilson.co.uk
(cherry picked from commit bb65548e3c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
When running gem_exec_nop, it floods the system with many requests (with
the goal of userspace submitting faster than the HW can process a single
empty batch). This causes the driver to continually resubmit new
requests onto the end of an active context, a flood of lite-restore
preemptions. If we time this just right, Tigerlake hangs.
Inserting a small delay between the processing of CS events and
submitting the next context, prevents the hang. Naturally it does not
occur with debugging enabled. The suspicion then is that this is related
to the issues with the CS event buffer, and inserting an mmio read of
the CS pointer status appears to be very successful in preventing the
hang. Other registers, or uncached reads, or plain mb, do not prevent
the hang, suggesting that register is key -- but that the hang can be
prevented by a simple udelay, suggests it is just a timing issue like
that encountered by commit 233c1ae3c8 ("drm/i915/gt: Wait for CSB
entries on Tigerlake"). Also note that the hang is not prevented by
applying CTX_DESC_FORCE_RESTORE, or by inserting a delay on the GPU
between requests.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Bruce Chang <yu.bruce.chang@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201015195023.32346-1-chris@chris-wilson.co.uk
(cherry picked from commit 6ca7217dff)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Matthew Auld noted that on more recent systems (such as the parser for
gen9) we may have objects that are larger than expected by the GEM uAPI
(i.e. greater than u32). These objects would have incorrect implicit
batch lengths, causing the parser to reject them for being incomplete,
or worse.
Based on a patch by Matthew Auld.
Reported-by: Matthew Auld <matthew.auld@intel.com>
Fixes: 435e8fc059 ("drm/i915: Allow parsing of unsized batches")
Testcase: igt/gem_exec_params/larger-than-life-batch
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20201015115954.871-1-chris@chris-wilson.co.uk
(cherry picked from commit 57b2d834bf)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Currently we leave the cache_level of the initial fb obj
set to NONE. This means on eLLC machines the first pin_to_display()
will try to switch it to WT which requires a vma unbind+bind.
If that happens during the fbdev initialization rcu does not
seem operational which causes the unbind to get stuck. To
most appearances this looks like a dead machine on boot.
Avoid the unbind by already marking the object cache_level
as WT when creating it. We still do an excplicit ggtt pin
which will rewrite the PTEs anyway, so they will match whatever
cache level we set.
Cc: <stable@vger.kernel.org> # v5.7+
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2381
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007120329.17076-1-ville.syrjala@linux.intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20201015122138.30161-1-chris@chris-wilson.co.uk
(cherry picked from commit d46b60a2e8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In order to avoid functional breakage of mis-programmed applications that
have grown to depend on unused MOCS entries, we are programming
those entries to be equal to fully cached ("L3 + LLC") entry.
These reserved and unspecified entries should not be used as they may be
changed to less performant variants with better coherency in the future
if more entries are needed.
v2: As suggested by Lucas De Marchi to utilise __init_mocs_table for
programming default value, setting I915_MOCS_PTE index of tgl_mocs_table
with desired value.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Francisco Jerez <currojerez@riseup.net>
Cc: Mathew Alwin <alwin.mathew@intel.com>
Cc: Mcguire Russell W <russell.w.mcguire@intel.com>
Cc: Spruit Neil R <neil.r.spruit@intel.com>
Cc: Zhou Cheng <cheng.zhou@intel.com>
Cc: Benemelis Mike G <mike.g.benemelis@intel.com>
Signed-off-by: Ayaz A Siddiqui <ayaz.siddiqui@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200729102539.134731-2-ayaz.siddiqui@intel.com
Cc: stable@vger.kernel.org
(cherry picked from commit 4d8a5cfe3b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In commit 7994672309 ("drm/i915: Assume 100% brightness when not in
DPCD control mode"), we fixed the brightness level when DPCD control was
not active to max brightness. This is as good as we can guess since most
backlights go on full when uncontrolled.
However in doing so we changed the semantics of the initial
'backlight.enabled' value. At least on Pixelbooks, they were relying
on the brightness level in DP_EDP_BACKLIGHT_BRIGHTNESS_MSB to be 0 on
boot such that enabled would be false. This causes the device to be
enabled when the brightness is set. Without this, brightness control
doesn't work. So by changing brightness to max, we also flipped enabled
to be true on boot.
To fix this, make enabled a function of brightness and backlight control
mechanism.
Fixes: 7994672309 ("drm/i915: Assume 100% brightness when not in DPCD control mode")
Cc: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Kevin Chowski <chowski@chromium.org>>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200918002845.32766-1-sean@poorly.run
(cherry picked from commit 4ade8f31c2)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
If guest fills non-priv bb on ApolloLake/Broxton as Mesa i965 does in:
717e7539124d (i965: Use a WC map and memcpy for the batch instead of pw-)
Due to the missing flush of bb filled by VM vCPU, host GPU hangs on
executing these MI_BATCH_BUFFER.
Temporarily workaround this by setting SNOOP bit for PAT3 used by PPGTT
PML4 PTE: PAT(0) PCD(1) PWT(1).
The performance is still expected to be low, will need further improvement.
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20201012045231.226748-1-colin.xu@intel.com
Guest driver may reset HWSP to 0 as init value during D3->D0:
The full sequence is:
- Boot ->D0
- Update HWSP
- D0->D3
- ...In D3 state...
- D3->D0
- DMLR reset.
- Set engine HWSP to 0.
- Set engine ring mode to 0.
- Set engine HWSP to correct value.
- Set engine ring mode to correct value.
Ring mode is masked register so set 0 won't take effect.
However HWPS addr 0 is considered as invalid GGTT address which will
report error like:
gvt: vgpu 1: write invalid HWSP address, reg:0x2080, value:0x0
gvt: vgpu 1: fail to emulate MMIO write 00002080 len 4
Detected your guest driver doesn't support GVT-g.
Now vgpu 2 will enter failsafe mode.
Zero out HWSP addr is considered as a valid setting from device driver
so don't treat it as invalid HWSP addr.
V2:
Treat HWSP addr 0 as valid. (zhenyu)
V3:
Change patch title.
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200911065239.147789-1-colin.xu@intel.com
This adds support for the TDO TL070WSH30 TFT-LCD panel module.
The panel has a 1024×600 resolution and uses 24 bit RGB per pixel.
It provides a MIPI DSI interface to the host, a built-in LED backlight
and touch controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200915121912.4347-5-narmstrong@baylibre.com
