No reason that I can see why we should enable the hpd detection logic
already during irq postinstall phase. We don't even do this on all
the platforms. We just need it before we actually enable the hotplug
interrupts in .hpd_irq_setup(), and in fact we already do it there as
well. Let's just eliminate the redundant early setup.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-15-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Use hpd_pin to parametrize BXT_DE_PORT_HP_DDI() to make it clear
these have nothing to do with DDI ports or PHYs as such. The only
thing that matters is the HPD pin assignment.
v2: Remember the gvt
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-8-ville.syrjala@linux.intel.com
Let's make the AUX CH names match the spec (AUX A-F for pre-tgl,
AUX A-C or AUX USBC1-6 for tgl+). And while at it let's include
the full encoder name in the AUX CH name as well (as opposed to
just using port_name() which wouldn't give us the right thing on
tgl+).
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-6-ville.syrjala@linux.intel.com
Let's pimp the DDI encoder->name to reflect what the spec calls them.
Ie. on pre-tgl DDI A-F, on tgl+ DDI A-C or DDI TC1-6.
Also since each encoder is really a combination of the DDI and the PHY
we include the PHY name as well.
ICL is a bit special since it already has the two different types
of DDIs (combo or TC) but it still calls them just DDI A-F regarless
of the type. For that let's add an extra "(TC)" note to remind
is which type of DDI it really is.
The code is darn ugly, but not sure there's much we can do about it.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-4-ville.syrjala@linux.intel.com
The mutex within the panfrost_queue_state should have the lifetime of
the queue, however it was erroneously initialised/destroyed during
panfrost_job_{open,close} which is called every time a client
opens/closes the drm node.
Move the initialisation/destruction to panfrost_job_{init,fini} where it
belongs.
Fixes: 1a11a88cfd ("drm/panfrost: Fix job timeout handling")
Signed-off-by: Steven Price <steven.price@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029170047.30564-1-steven.price@arm.com
When the GPU's ACE-Lite interface is fully wired up and capable of
snooping CPU caches, it may be described as "dma-coherent" in
devicetree, which will already inform the DMA layer not to perform
unnecessary cache maintenance. However, we still need to ensure that
the GPU uses the appropriate cacheable outer-shareable attributes in
order to generate the requisite snoop signals, and that CPU mappings
don't create a mismatch by using a non-cacheable type either.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7024ce18c1cb1a226e918037d49175571db0b436.1600780574.git.robin.murphy@arm.com
This reverts commit f878122841 ("drm/amdgpu:
Fix bug where DPM is not enabled after hibernate and resume").
It was intended to fix Hawaii S4(hibernation) issue but break S3. As
ixFEATURE_STATUS is filled with garbage data on resume which can be
only cleared by reloading smc firmware(but that will involve many
changes). So, we will revert this S4 fix and seek a new way.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that the succeeding resume can be performed based on
a clean state.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Which can be used for S4(hibernation) support.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct some registers bitmasks and add mmBIOS_SCRATCH_7
reset.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This can address the random SDMA hang after pci config reset
seen on Hawaii.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Navi14 0x7340/C9 SKU has no display and video support, remove them.
Signed-off-by: Flora Cui <flora.cui@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct spelling in one of the comment.
s/defalut/default/p
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
core_link_write_dpcd() returns enum dc_status, not ddc_result:
display/dc/core/dc_link_dp.c: In function 'dp_set_panel_mode':
display/dc/core/dc_link_dp.c:4237:11: warning: implicit conversion from 'enum dc_status' to 'enum ddc_result'
[-Wenum-conversion]
Avoid the warning by using the correct enum in the caller.
Fixes: 0b22632243 ("drm/amd/display: Synchronous DisplayPort Link Training")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A recent change added two uint16_t elements to PPTable_t and reduced the
uint32_t array down to 8 elements. This results in the dev_info printing
of pptable->SkuReserved[8] accessing a value that is out-of-range on
array SkuReserved. The array has been shrunk by 1 element, so remove
this extraneous dev_info message.
Addresses-Coverity: ("Out-of-bounds read")
Fixes: 1dc3c5a95b ("drm/amd/pm: update driver if file for sienna cichlid")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccinelle report:
./drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:1367:3-5:
WARNING: possible condition with no effect (if == else)
Both branches are the same, so remove the if/else altogether.
Fixes: 81875979f0 ("drm/amd/display: Remove extra pairs of parentheses in dce_calcs.c")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's unused and identical to dal_cmd_tbl_helper_dce112_get_table2.
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a separate config option at this point.
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit f878122841 ("drm/amdgpu:
Fix bug where DPM is not enabled after hibernate and resume").
It was intended to fix Hawaii S4(hibernation) issue but break S3. As
ixFEATURE_STATUS is filled with garbage data on resume which can be
only cleared by reloading smc firmware(but that will involve many
changes). So, we will revert this S4 fix and seek a new way.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that the succeeding resume can be performed based on
a clean state.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Which can be used for S4(hibernation) support.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct some registers bitmasks and add mmBIOS_SCRATCH_7
reset.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This can address the random SDMA hang after pci config reset
seen on Hawaii.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use ">= CHIP_SIENNA_CICHLID" to replace per asic check
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Hawking.Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
First of all don't snprintf into a char buffer allocated on the stack with
a constant hubname.
Then cleanup to exit the function early in case of a ratelimit or SRIOV.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need this to pass dp compliance.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nikola Cornij <nikola.cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since the unique_id is now obtained in amdgpu in smu_late_init,
topology misses getting the value during KFD device initialization.
To work around this, we use amdgpu_amdkfd_get_unique_id to get
the unique_id at read time. Due to this, we can remove unique_id from
the kfd_dev structure, since we only need it in the KFD node properties
struct
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to enable the rest functions of swSMU for vangogh.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to add some swSMU functions for vangogh, to support the
sensor info on "hwmon" and pm info.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to add one new function to get 32 bit feature mask for
vangogh.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to remove some redundant smu message mapping for vangogh.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
