Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is an upper bound to the value that a watermark may hold. That
upper bound is not immediately obvious during configuration, and it
might be possible to have accidental truncation.
Actually this has happened already, add a warning to prevent it from
happening again.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
VCAP IS1 is a VCAP module which can filter on the most common L2/L3/L4
Ethernet keys, and modify the results of the basic QoS classification
and VLAN classification based on those flow keys.
There are 3 VCAP IS1 lookups, mapped over chains 10000, 11000 and 12000.
Currently the driver is hardcoded to use IS1_ACTION_TYPE_NORMAL half
keys.
Note that the VLAN_MANGLE has been omitted for now. In hardware, the
VCAP_IS1_ACT_VID_REPLACE_ENA field replaces the classified VLAN
(metadata associated with the frame) and not the VLAN from the header
itself. There are currently some issues which need to be addressed when
operating in standalone, or in bridge with vlan_filtering=0 modes,
because in those cases the switch ports have VLAN awareness disabled,
and changing the classified VLAN to anything other than the pvid causes
the packets to be dropped. Another issue is that on egress, we expect
port tagging to push the classified VLAN, but port tagging is disabled
in the modes mentioned above, so although the classified VLAN is
replaced, it is not visible in the packet transmitted by the switch.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mscc_ocelot_switch_lib is common between a pure switchdev and
a DSA driver, the procedure of retrieving a net_device for a certain
port index differs, as those are registered by their individual
front-ends.
Up to now that has been dealt with by always passing the port index to
the switch library, but now, we're going to need to work with net_device
pointers from the tc-flower offload, for things like indev, or mirred.
It is not desirable to refactor that, so let's make sure that the flower
offload core has the ability to translate between a net_device and a
port index properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we are deriving these from the constants exposed by the
hardware, we can delete the static info we're keeping in the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The numbers in struct vcap_props are not intuitive to derive, because
they are not a straightforward copy-and-paste from the reference manual
but instead rely on a fairly detailed level of understanding of the
layout of an entry in the TCAM and in the action RAM. For this reason,
bugs are very easy to introduce here.
Ease the work of hardware porters and read from hardware the constants
that were exported for this particular purpose. Note that this implies
that struct vcap_props can no longer be const.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation step for the offloading to ES0, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation step for the offloading to IS1, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Ocelot switches there are 3 TCAMs: VCAP ES0, IS1 and IS2, which
have the same configuration interface, but different sets of keys and
actions. The driver currently only supports VCAP IS2.
In preparation of VCAP IS1 and ES0 support, the existing code must be
generalized to work with any VCAP.
In that direction, we should move the structures that depend upon VCAP
instantiation, like vcap_is2_keys and vcap_is2_actions, out of struct
ocelot and into struct vcap_props .keys and .actions, a structure that
is replicated 3 times, once per VCAP. We'll pass that structure as an
argument to each function that does the key and action packing - only
the control logic needs to distinguish between ocelot->vcap[VCAP_IS2]
or IS1 or ES0.
Another change is to make use of the newly introduced ocelot_target_read
and ocelot_target_write API, since the 3 VCAPs have the same registers
but put at different addresses.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port mask width was larger than the actual number of ports, and
therefore, all fields following this one were also shifted by the number
of excess bits. But the driver doesn't use the REW_OP, SMAC_REPLACE_ENA
or ACL_ID bits from the action vector, so the bug was inconsequential.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 goals that we follow:
- Reduce the header size
- Make the header size equal between RX and TX
The issue that required long prefix on RX was the fact that the ocelot
DSA tag, being put before Ethernet as it is, would overlap with the area
that a DSA master uses for RX filtering (destination MAC address
mainly).
Now that we can ask DSA to put the master in promiscuous mode, in theory
we could remove the prefix altogether and call it a day, but it looks
like we can't. Using no prefix on ingress, some packets (such as ICMP)
would be received, while others (such as PTP) would not be received.
This is because the DSA master we use (enetc) triggers parse errors
("MAC rx frame errors") presumably because it sees Ethernet frames with
a bad length. And indeed, when using no prefix, the EtherType (bytes
12-13 of the frame, bits 96-111) falls over the REW_VAL field from the
extraction header, aka the PTP timestamp.
When turning the short (32-bit) prefix on, the EtherType overlaps with
bits 64-79 of the extraction header, which are a reserved area
transmitted as zero by the switch. The packets are not dropped by the
DSA master with a short prefix. Actually, the frames look like this in
tcpdump (below is a PTP frame, with an extra dsa_8021q tag - dadb 0482 -
added by a downstream sja1105).
89:0c:a9:f2:01:00 > 88:80:00:0a:00:1d, 802.3, length 0: LLC, \
dsap Unknown (0x10) Individual, ssap ProWay NM (0x0e) Response, \
ctrl 0x0004: Information, send seq 2, rcv seq 0, \
Flags [Response], length 78
0x0000: 8880 000a 001d 890c a9f2 0100 0000 100f ................
0x0010: 0400 0000 0180 c200 000e 001f 7b63 0248 ............{c.H
0x0020: dadb 0482 88f7 1202 0036 0000 0000 0000 .........6......
0x0030: 0000 0000 0000 0000 0000 001f 7bff fe63 ............{..c
0x0040: 0248 0001 1f81 0500 0000 0000 0000 0000 .H..............
0x0050: 0000 0000 0000 0000 0000 0000 ............
So the short prefix is our new default: we've shortened our RX frames by
12 octets, increased TX by 4, and headers are now equal between RX and
TX. Note that we still need promiscuous mode for the DSA master to not
drop it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
state->speed holds a value of 10, 100, 1000 or 2500, but
QSYS_TAG_CONFIG_LINK_SPEED expects a value of 0, 1, 2, 3. So convert the
speed to a proper value.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seville does not need to depend on PCI or on the ENETC MDIO controller.
There will also be other compile-time differences in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not only does Sevile not have a PTP clock, but with separate modules,
this structure cannot even live in felix.c, due to the .owner =
THIS_MODULE assignment causing this link time error:
drivers/net/dsa/ocelot/felix.o:(.data+0x0): undefined reference to `__this_module'
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we don't plan on making any changes to this function, currently
this is the only remaining dependency between felix and seville, after
the PCS has been refactored out into pcs-lynx.c.
Duplicate this function in seville to break the dependency completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Over the time, some patches have introduced structures aligned with
spaces, near structures aligned with tabs. Fix the inconsistencies.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The overall idea (issue soft reset, enable memories, initialize
memories, enable core) is the same, so it would make sense that an
attempt is made to unify the procedures.
It is not immediately obvious that the fields are not part of the same
register targets, though. So add a comment.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since these helpers for regmap fields are available, use them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the helper functions introduced by the newly added
Lynx PCS MDIO module in the Felix VSC9959 and Seville VSC9953.
Instead of representing the PCS as a phy_device, a mdio_device structure
will be passed to the Lynx module which is now actually implementing all
the PCS configuration and status reporting.
All code previously used for PCS monitoring and runtime configuration
is removed and replaced will calls to the Lynx PCS operations.
Tested on the following SERDES protocols of LS1028A: 0x7777
(2500Base-X), 0x85bb (QSGMII), 0x9999 (SGMII) and 0x13bb (USXGMII).
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there are USXGMII constants available, drop the old definitions
and reuse the generic ones.
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is another switch from Vitesse / Microsemi / Microchip, that has
10 ports (8 external, 2 internal) and is integrated into the Freescale /
NXP T1040 PowerPC SoC. It is very similar to Felix from NXP LS1028A,
except that this is a platform device and Felix is a PCI device, and it
doesn't support IEEE 1588 and TSN.
Like Felix, this driver configures its own PCS on the internal MDIO bus
using a phy_device abstraction for it (yes, it will be refactored to use
a raw mdio_device, like other phylink drivers do, but let's keep it like
that for now). But unlike Felix, the MDIO bus and the PCS are not from
the same vendor. The PCS is the same QorIQ/Layerscape PCS as found in
Felix/ENETC/DPAA*, but the internal MDIO bus that is used to access it
is actually an instantiation of drivers/net/phy/mdio-mscc-miim.c. But it
would be difficult to reuse that driver (it doesn't even use regmap, and
it's less than 200 lines of code), so we hand-roll here some internal
MDIO bus accessors within seville_vsc9953.c, which serves the purpose of
driving the PCS absolutely fine.
Also, same as Felix, the PCS doesn't support dynamic reconfiguration of
SerDes protocol, so we need to do pre-validation of PHY mode from device
tree and not let phylink change it.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix is not actually meant to be a DSA driver only for the switch
inside NXP LS1028A, but an umbrella for all Vitesse / Microsemi /
Microchip switches that are register-compatible with Ocelot and that are
using in DSA mode (with an NPI Ethernet port).
For the dsa_switch_ops exported by the felix driver to be generic enough
to be used by other non-PCI switches, we need to move the PCI-specific
probing to the low-level translation module felix_vsc9959.c. This way,
other switches can have their own probing functions, as platform devices
or otherwise.
This patch also removes the "Felix instance table", which did not stand
the test of time and is unnecessary at this point.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_wm_encode function deals with setting thresholds for pause
frame start and stop. In Ocelot and Felix the register layout is the
same, but for Seville, it isn't. The easiest way to accommodate Seville
hardware configuration is to introduce a function pointer for setting
this up.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seville has a different bitwise layout than Ocelot and Felix.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use tag_ocelot.c don't have the exact
same bitfield layout for the DSA tags. The destination ports field is
different for Seville VSC9953 for example. So the choices are to either
duplicate tag_ocelot.c into a new tag_seville.c (sub-optimal) or somehow
take into account a supposed ocelot->dest_ports_offset when packing this
field into the DSA injection header (again not ideal).
Secondly, tag_ocelot.c already needs to memset a 128-bit area to zero
and call some packing() functions of dubious performance in the
fastpath. And most of the values it needs to pack are pretty much
constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good
if we could improve that.
The proposed solution is to allocate a memory area per port at probe
time, initialize that with the statically defined bits as per chip
hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently Felix and Ocelot share the same bit layout in these per-port
registers, but Seville does not. So we need reg_fields for that.
Actually since these are per-port registers, we need to also specify the
number of ports, and register size per port, and use the regmap API for
multiple ports.
There's a more subtle point to be made about the other 2 register
fields:
- QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG
- QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE
which we are not writing any longer, for 2 reasons:
- Using the previous API (ocelot_write_rix), we were only writing 1 for
Felix and Ocelot, which was their hardware-default value, and which
there wasn't any intention in changing.
- In the case of SCH_NEXT_CFG, in fact Seville does not have this
register field at all, and therefore, if we want to have common code
we would be required to not write to it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the register definitions for the MSCC MIIM MDIO controller in
preparation for seville_vsc9959.c to create its accessors for the
internal MDIO bus.
Since we've introduced elements to ocelot_regfields that are not
instantiated by felix and ocelot, we need to define the size of the
regfields arrays explicitly, otherwise ocelot_regfields_init, which
iterates up to REGFIELD_MAX, will fault on the undefined regfield
entries (if we're lucky).
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, there are some minimal register differences between
VSC7514 Ocelot and VSC9959 Felix. To be precise, the PCS1G registers are
missing from Felix because it was integrated with an NXP PCS.
But with VSC9953 Seville (not yet introduced), the register differences
are more pronounced. The MAC registers are located at different offsets
within the DEV_GMII target. So we need to refactor the driver to keep a
regmap even for per-port registers. The callers of the ocelot_port_readl
and ocelot_port_writel were kept unchanged, only the implementation is
now more generic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink now requires that parameters established through
auto-negotiation be written into the MAC at the time of the
mac_link_up() callback. In the case of felix, that means taking the port
out of reset, setting the correct timers for PAUSE frames, and
enabling/disabling TX flow control.
This patch also splits the inband and noinband configuration of the
vsc9959 PCS (currently found in a function called "init") into 2
different functions, which have a nomenclature closer to phylink:
"config", for inband setup, and "link_up", for noinband (forced) setup.
This is necessary as a preparation step for giving up control of the PCS
to phylink, which will be done in further patch series.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink uses the .mac_an_restart method to offer the user an
implementation of the "ethtool -r" behavior, when the media-side auto
negotiation can be restarted by the local MAC PCS. This is the case for
fiber modes 1000Base-X and 2500Base-X (IEEE clause 37) that don't have
an Ethernet PHY connected locally, and the media is connected to the MAC
PCS directly.
On the other hand, the Cisco SGMII and USXGMII standards also have an
auto negotiation mechanism based on IEEE 802.3 clause 37 (their
respective specs require a MAC PCS and a PHY PCS to implement the same
state machine, which is described in IEEE 802.3 "Auto-Negotiation Figure
37-6"), so the ability to restart auto-negotiation is intrinsically
symmetrical (the MAC PCS can do it too).
However, it appears that not all SGMII/USXGMII PHYs have logic to
restart the MDI-side auto-negotiation process when they detect a
transition of the SGMII link from data mode to configuration mode.
Some do (VSC8234) and some don't (AR8033, MV88E1111). IEEE and/or Cisco
specification wordings to not help to prove whether propagating the "AN
restart" event from MII side ("mr_restart_an") to MDI side
("mr_restart_negotiation") is required behavior - neither of them
specifies any mandatory interaction between the clause 37 AN state
machine from Figure 37-6 and the clause 28 AN state machine from Figure
28-18.
Therefore, even if a certain behavior could be proven as being required,
real-life SGMII/USXGMII PHYs are inconsistent enough that a clause 37 AN
restart cannot be used by phylink to reliably trigger a media-side
renegotiation, when the user requests it via ethtool.
The only remaining use that the .mac_an_restart callback might possibly
have, given what we know now, is to implement some silicon quirks, but
so far that has proven to not be necessary.
So remove this code for now, since it never gets called and we don't
foresee any circumstance in which it might be, either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ping tested:
[ 11.808455] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 11.816497] IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready
[root@LS1028ARDB ~] # ethtool -s swp0 advertise 0x4
[ 18.844591] mscc_felix 0000:00:00.5 swp0: Link is Down
[ 22.048337] mscc_felix 0000:00:00.5 swp0: Link is Up - 100Mbps/Half - flow control off
[root@LS1028ARDB ~] # ip addr add 192.168.1.1/24 dev swp0
[root@LS1028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes
(...)
^C--- 192.168.1.2 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.383/0.611/1.051 ms
[root@LS1028ARDB ~] # ethtool -s swp0 advertise 0x10
[ 355.637747] mscc_felix 0000:00:00.5 swp0: Link is Down
[ 358.788034] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Half - flow control off
[root@LS1028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes
(...)
^C
--- 192.168.1.2 ping statistics ---
16 packets transmitted, 16 packets received, 0% packet loss
round-trip min/avg/max = 0.301/0.384/1.138 ms
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver appears to write to BMCR_SPEED and BMCR_DUPLEX, fields which
are read-only, since they are actually configured through the
vendor-specific IF_MODE (0x14) register.
But the reason we're writing back the read-only values of MII_BMCR is to
alter these writable fields:
BMCR_RESET
BMCR_LOOPBACK
BMCR_ANENABLE
BMCR_PDOWN
BMCR_ISOLATE
BMCR_ANRESTART
In particular, the only field which is really relevant to this driver is
BMCR_ANENABLE. Clarify that intention by spelling it out, using
phy_set_bits and phy_clear_bits.
The driver also made a few writes to BMCR_RESET and BMCR_ANRESTART which
are unnecessary and may temporarily disrupt the link to the PHY. Remove
them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller of devm_ioremap_resource(), either accidentally
or by wrong assumption, is writing back derived resource data
to global static resource initialization tables that should
have been constant. Meaning that after it computes the final
physical start address it saves the address for no reason
in the static tables. This doesn't affect the first driver
probing after reboot, but it breaks consecutive driver reloads
(i.e. driver unbind & bind) because the initialization tables
no longer have the correct initial values. So the next probe()
will map the device registers to wrong physical addresses,
causing ARM SError async exceptions.
This patch fixes all of the above.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently burst is clamping on rate and not burst, the assignment
of burst from the clamping discards the previous assignment of burst.
This looks like a cut-n-paste error from the previous clamping
calculation on ramp. Fix this by replacing ramp with burst.
Addresses-Coverity: ("Unused value")
Fixes: 0fbabf875d ("net: dsa: felix: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC9959 hardware support the Credit Based Shaper(CBS) which part
of the IEEE-802.1Qav. This patch support sch_cbs set for VSC9959.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot VSC9959 switch supports time-based egress shaping in hardware
according to IEEE 802.1Qbv. This patch add support for TAS configuration
on egress port of VSC9959 switch.
Felix driver is an instance of Ocelot family, with a DSA front-end. The
patch uses tc taprio hardware offload to setup TAS set function on felix
driver.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running 'bridge fdb dump' on Felix, sometimes learnt and static MAC
addresses would appear, sometimes they wouldn't.
Turns out, the MAC table has 4096 entries on VSC7514 (Ocelot) and 8192
entries on VSC9959 (Felix), so the existing code from the Ocelot common
library only dumped half of Felix's MAC table. They are both organized
as a 4-way set-associative TCAM, so we just need a single variable
indicating the correct number of rows.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wave programming registers definitions for Ocelot platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the cls_flower methods from the ocelot driver and hook them up to
the DSA passthrough layer.
Tables for the VCAP IS2 parameters, as well as half key packing (field
offsets and lengths) need to be defined for the VSC9959 core, as they
are different from Ocelot, mainly due to the different port count.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy-mode = "gmii" is confusing because it may mean that the port
supports the 8-bit-wide parallel data interface pinout, which it
doesn't.
It may also be confusing because one of the "gmii" internal ports is
actually overclocked to run at 2.5Gbps (even though, yes, as far as the
switch MAC is concerned, it still thinks it's gigabit).
So use the phy-mode = "internal" property to describe the internal ports
inside the NXP LS1028A chip (the ones facing the ENETC). The change
should be fine, because the device tree bindings document is yet to be
introduced, and there are no stable DT blobs in use.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs like VSC8234 don't like it when AN restarts on their system side
and they restart line side AN too, going into an endless link up/down loop.
Don't restart PCS AN if link is up already.
Although in theory this feedback loop should be possible with the other
in-band AN modes too, for some reason it was not seen with the VSC8514
QSGMII and AQR412 USXGMII PHYs. So keep this logic only for SGMII where
the problem was found.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least some PHYs (AQR412) don't advertise copper-side link status
during system side AN.
So remove this duplicate assignment to pcs->link and rely on the
previous one for link state: the local indication from the MAC PCS.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Layerscape SoCs traditionally expose the SerDes configuration/status for
Ethernet protocols (PCS for SGMII/USXGMII/10GBase-R etc etc) in a register
format that is compatible with clause 22 or clause 45 (depending on
SerDes protocol). Each MAC has its own internal MDIO bus on which there
is one or more of these PCS's, responding to commands at a configurable
PHY address. The per-port internal MDIO bus (which is just for PCSs) is
totally separate and has nothing to do with the dedicated external MDIO
controller (which is just for PHYs), but the register map for the MDIO
controller is the same.
The VSC9959 (Felix) switch instantiated in the LS1028A is integrated
in hardware with the ENETC PCS of its DSA master, and reuses its MDIO
controller driver, so Felix has been made to depend on it in Kconfig.
+------------------------------------------------------------------------+
| +--------+ GMII (typically disabled via RCW) |
| ENETC PCI | ENETC |--------------------------+ |
| Root Complex | port 3 |-----------------------+ | |
| Integrated +--------+ | | |
| Endpoint | | |
| +--------+ 2.5G GMII | | |
| | ENETC |--------------+ | | |
| | port 2 |-----------+ | | | |
| +--------+ | | | | |
| +--------+ +--------+ |
| | Felix | | Felix | |
| | port 4 | | port 5 | |
| +--------+ +--------+ |
| |
| +--------+ +--------+ +--------+ +--------+ +--------+ +--------+ |
| | ENETC | | ENETC | | Felix | | Felix | | Felix | | Felix | |
| | port 0 | | port 1 | | port 0 | | port 1 | | port 2 | | port 3 | |
+------------------------------------------------------------------------+
| |||| SerDes | |||| |||| |||| |||| |
| +--------+block | +--------------------------------------------+ |
| | ENETC | | | ENETC port 2 internal MDIO bus | |
| | port 0 | | | PCS PCS PCS PCS | |
| | PCS | | | 0 1 2 3 | |
+-----------------|------------------------------------------------------+
v v v v v v
SGMII/ RGMII QSGMII/QSXGMII/4xSGMII/4x1000Base-X/4x2500Base-X
USXGMII/ (bypasses
1000Base-X/ SerDes)
2500Base-X
In the LS1028A SoC described above, the VSC9959 Felix switch is PF5 of
the ENETC root complex, and has 2 BARs:
- BAR 4: the switch's effective registers
- BAR 0: the MDIO controller register map lended from ENETC port 2
(PF2), for accessing its associated PCS's.
This explanation is necessary because the patch does some renaming
"pci_bar" -> "switch_pci_bar" for clarity, which would otherwise appear
a bit obtuse.
The fact that the internal MDIO bus is "borrowed" is relevant because
the register map is found in PF5 (the switch) but it triggers an access
fault if PF2 (the ENETC DSA master) is not enabled. This is not treated
in any way (and I don't think it can be treated).
All of this is so SoC-specific, that it was contained as much as
possible in the platform-integration file felix_vsc9959.c.
We need to parse and pre-validate the device tree because of 2 reasons:
- The PHY mode (SerDes protocol) cannot change at runtime due to SoC
design.
- There is a circular dependency in that we need to know what clause the
PCS speaks in order to find it on the internal MDIO bus. But the
clause of the PCS depends on what phy-mode it is configured for.
The goal of this patch is to make steps towards removing the bootloader
dependency for SGMII PCS pre-configuration, as well as to add support
for monitoring the in-band SGMII AN between the PCS and the system-side
link partner (PHY or other MAC).
In practice the bootloader dependency is not completely removed. U-Boot
pre-programs the PHY address at which each PCS can be found on the
internal MDIO bus (MDEV_PORT). This is needed because the PCS of each
port has the same out-of-reset PHY address of zero. The SerDes register
for changing MDEV_PORT is pretty deep in the SoC (outside the addresses
of the ENETC PCI BARs) and therefore inaccessible to us from here.
Felix VSC9959 and Ocelot VSC7514 are integrated very differently in
their respective SoCs, and for that reason Felix does not use the Ocelot
core library for PHYLINK. On one hand we don't want to impose the
fixed phy-mode limitation to Ocelot, and on the other hand Felix doesn't
need to force the MAC link speed the way Ocelot does, since the MAC is
connected to the PCS through a fixed GMII, and the PCS is the one who
does the rate adaptation at lower link speeds, which the MAC does not
even need to know about. In fact changing the GMII speed for Felix
irrecoverably breaks transmission through that port until a reset.
The pair with ENETC port 3 and Felix port 5 is optional and doesn't
support tagging. When we enable it, swp5 is a regular slave port, albeit
an internal one. The trouble is that it doesn't work, and that is
because the DSA PHYLIB adaptation layer doesn't treat fixed-link slave
ports. So that is yet another reason for wanting to convert Felix to the
native PHYLINK API.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to define PTP registers for felix_vsc9959.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
